Specifications
4-20
PA-8E 10BaseT Ethernet Port Adapter Installation and Configuration
OL-3494-04
Chapter 4 Configuring the PA-8E
Checking the Configuration
Router# show interfaces ethernet 0/6
Ethernet0/6 is administratively down, line protocol is down
Hardware is cyBus Ethernet, address is 0000.0ca5.2306 (bia 0000.0ca5.238f)
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255
Encapsulation ARPA, loopback not set, keepalive set (10 sec)
(display text omitted)
Router# show interfaces ethernet 0/7
Ethernet0/7 is administratively down, line protocol is down
Hardware is cyBus Ethernet, address is 0000.0ca5.2307 (bia 0000.0ca5.2391)
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255
Encapsulation ARPA, loopback not set, keepalive set (10 sec)
The following example of the show interfaces ethernet command shows all of the information specific
to the first PA-8E interface port (interface port 0) in port adapter slot 1:
Router# show interfaces ethernet 1/0
Ethernet1/0 is administratively down, line protocol is down
Hardware is cyBus Ethernet, address is 0000.0ca5.2309 (bia 0000.0ca5.2392)
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255
Encapsulation ARPA, loopback not set, keepalive set (10 sec)
ARP type: ARPA, ARP Timeout 4:00:00
Last input never, output never, output hang never
Last clearing of “show interface” counters 2:56:26
Output queue 0/40, 0 drops; input queue 0/75, 0 drops
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 input packets with dribble condition detected
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets, 0 restarts
0 output buffer failures, 0 output buffers swapped out
Cisco 7200 Series and Cisco uBR7200 Series Routers—Example Output of the show interfaces Command
Following are examples of the show interfaces command from a Cisco 7200 series router or a
Cisco uBR7200 series router. In these examples, the eight serial interfaces (0 to 7) are on a port adapter
in port adapter slot 2; also, most of the status information for each interface is omitted. (Interfaces are
administratively shut down until you enable them.)
Router# show interfaces ethernet 2/0
Ethernet2/0 is administratively down, line protocol is down
Hardware is AmdP2 Ethernet, address is 10.0.0.0 10.255.255.255 (bia 0000.0ca5.2389)
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255
Encapsulation ARPA, loopback not set, keepalive set (10 sec)
(display text omitted)
Router# show interfaces ethernet 2/1
Ethernet2/1 is administratively down, line protocol is down
Hardware is AmdP2 Ethernet, address is 10.0.0.0 10.255.255.255 (bia 0000.0ca5.238a)
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255
Encapsulation ARPA, loopback not set, keepalive set (10 sec)
(display text omitted)Router# sh int e 2/2
Ethernet2/2 is administratively down, line protocol is down
Hardware is AmdP2 Ethernet, address is 10.0.0.0 10.255.255.255 (bia 0000.0ca5.238b)
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255
Encapsulation ARPA, loopback not set, keepalive set (10 sec)
(display text omitted)