Specifications
Table Of Contents
- Software Configuration Guide
- Contents
- Preface
- Understanding Interface Numbering and Cisco IOS Software Basics
- Understanding Interface Numbering
- Understanding Cisco IOS Software Basics
- Upgrading to a New Cisco IOS Release
- Where to Go Next
- Using the Setup Command Facility
- Before Starting Your Router
- Using the setup Command Facility
- Configuring Global Parameters
- Configuring Interface Parameters
- Completing the Configuration
- Where to Go Next
- Configuring with the Command-Line Interface
- Configuring the Host Name and Password
- Configuring 1-Port and 2-Port Ethernet Interfaces
- Configuring Fast Ethernet Interfaces
- Configuring Asynchronous/Synchronous Serial Network Modules or WAN Interface Cards
- Configuring 16-Port and 32-Port Asynchronous Network Modules
- Configuring ISDN BRI WAN Interface Cards
- Configuring T1 and E1 Interfaces
- Configuring T1 (FT1) WAN Interface Cards
- Configuring ATM Interfaces
- Configuring Inverse Multiplexing for ATM Interfaces
- Configuring Analog Modem Interfaces
- Configuring Wireless Multipoint Interfaces
- Checking the Interface Configuration
- Configuring 1-Port ADSL WAN Interface Card
- Configuring the NM-AIC-64, Contact Closure Network Module
- Configuring the 1-Port HSSI Network Module
- Configuring the Compression Network Module for the Cisco 3600 Series Routers
- Configuring the Digital Modem Network Module for the Cisco 3640 Router
- Prerequisites
- Configuration Tasks
- Configure the E1/T1 Network Module for ISDN PRI
- Configure the ISDN D-Channel Serial Interfaces
- Configure the Loopback Interface
- Configure the LAN Interface
- Create the Group Asynchronous Interface
- Configure the ISDN Dialer Interface
- Configure the Default IP Pool Information
- Configure Modem Lines for Dial-In and Dial-Out
- Configuration Example
- Configuring 1-Port G.SHDSL WAN Interface Card
- Saving Configuration Changes
- Where to Go Next
- Configuring Voice-over-IP
- Voice-over-IP Prerequisites
- Configuring the Voice Interface
- Voice-over-IP Configuration Examples
- Where to Go Next
- Configuration Examples
- Cisco 2600 Series Router Configuration Example
- Cisco 3631 Router Configuration Example
- Cisco 3725 Router Configuration Example
- 1-Port ADSL WAN Interface Card Configuration Examples
- NM-AIC-64, Contact Closure NetworkConfiguration Examples
- Cisco 3640 Central Site Configuration to Support ISDN and Modem Calls
- Formatting the Compact Flash Memory Cards
- Using the ROM Monitor
- Index
3-9
Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers
OL-1957-03
Chapter 3 Configuring with the Command-Line Interface
Configuring 16-Port and 32-Port Asynchronous Network Modules
Configuring 16-Port and 32-Port Asynchronous Network
Modules
You can configure the asynchronous interface manually by entering Cisco IOS commands on the
command line. This method, called configuration mode, provides the greatest power and flexibility.
Timesaver Before you begin, disconnect all WAN cables from the router to keep it from trying to run the
AutoInstall process. The router tries to run AutoInstall whenever you power it ON, if there is a WAN
connection on both ends and the router does not have a valid configuration file stored in nonvolatile
random-access memory (NVRAM) (for instance, when you add a new interface). It can take several
minutes for the router to determine that AutoInstall is not connected to a remote Transmission
Control Protocol/Internet Protocol (TCP/IP) host.
Before you begin configuring the asynchronous interface, make sure you:
• Connect a console to the router.
• Power on the router.
Table 3-4 Clock Rate Settings for 2-Port Asynchronous/Synchronous Serial WAN Interface Card
Timer (bits per
second)
Syntax (bits per
second)
Default Setting (bits
per second)
1200 28800 72000
2400 32000 115200
4800 38400 125000
9600 56000 128000
14400 57600
19200 64000
Table 3-5 Clock Rate Settings for 4-Port/8-Port Asynchronous/Synchronous Serial Network Module
Timer (bits per
second)
Syntax (bits per
second)
Default Setting (bits
per second)
300 19200 64000
1200 28800 72000
2400 32000 115200
4800 38400 128000
9600 56000
14400 57600