Specifications
Table Of Contents
- Software Configuration Guide
- Contents
- Preface
- Understanding Interface Numbering and Cisco IOS Software Basics
- Understanding Interface Numbering
- Understanding Cisco IOS Software Basics
- Upgrading to a New Cisco IOS Release
- Where to Go Next
- Using the Setup Command Facility
- Before Starting Your Router
- Using the setup Command Facility
- Configuring Global Parameters
- Configuring Interface Parameters
- Completing the Configuration
- Where to Go Next
- Configuring with the Command-Line Interface
- Configuring the Host Name and Password
- Configuring 1-Port and 2-Port Ethernet Interfaces
- Configuring Fast Ethernet Interfaces
- Configuring Asynchronous/Synchronous Serial Network Modules or WAN Interface Cards
- Configuring 16-Port and 32-Port Asynchronous Network Modules
- Configuring ISDN BRI WAN Interface Cards
- Configuring T1 and E1 Interfaces
- Configuring T1 (FT1) WAN Interface Cards
- Configuring ATM Interfaces
- Configuring Inverse Multiplexing for ATM Interfaces
- Configuring Analog Modem Interfaces
- Configuring Wireless Multipoint Interfaces
- Checking the Interface Configuration
- Configuring 1-Port ADSL WAN Interface Card
- Configuring the NM-AIC-64, Contact Closure Network Module
- Configuring the 1-Port HSSI Network Module
- Configuring the Compression Network Module for the Cisco 3600 Series Routers
- Configuring the Digital Modem Network Module for the Cisco 3640 Router
- Prerequisites
- Configuration Tasks
- Configure the E1/T1 Network Module for ISDN PRI
- Configure the ISDN D-Channel Serial Interfaces
- Configure the Loopback Interface
- Configure the LAN Interface
- Create the Group Asynchronous Interface
- Configure the ISDN Dialer Interface
- Configure the Default IP Pool Information
- Configure Modem Lines for Dial-In and Dial-Out
- Configuration Example
- Configuring 1-Port G.SHDSL WAN Interface Card
- Saving Configuration Changes
- Where to Go Next
- Configuring Voice-over-IP
- Voice-over-IP Prerequisites
- Configuring the Voice Interface
- Voice-over-IP Configuration Examples
- Where to Go Next
- Configuration Examples
- Cisco 2600 Series Router Configuration Example
- Cisco 3631 Router Configuration Example
- Cisco 3725 Router Configuration Example
- 1-Port ADSL WAN Interface Card Configuration Examples
- NM-AIC-64, Contact Closure NetworkConfiguration Examples
- Cisco 3640 Central Site Configuration to Support ISDN and Modem Calls
- Formatting the Compact Flash Memory Cards
- Using the ROM Monitor
- Index
Contents
vii
Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers
OL-1957-03
Configure the Loopback Interface 3-55
Configure the LAN Interface 3-55
Create the Group Asynchronous Interface 3-55
Configure the ISDN Dialer Interface 3-56
Configure the Default IP Pool Information 3-57
Configure Modem Lines for Dial-In and Dial-Out 3-57
Configure the Modem for Dial-In 3-58
Configure the Modem for Dial-Out 3-58
Configuration Example 3-58
Configuring 1-Port G.SHDSL WAN Interface Card 3-58
Restrictions 3-60
Prerequisites 3-60
Configuration Tasks 3-60
Configuring G.SHDSL on a Cisco Router 3-60
Configuring ILMI on the DSLAM Connected to the ADSL WAN 3-62
Verifying ATM Configuration 3-62
Configuration Examples 3-64
Saving Configuration Changes 3-65
Where to Go Next 3-65
CHAPTER
4 Configuring Voice-over-IP 4-1
Voice-over-IP Prerequisites 4-1
Configuring the Voice Interface 4-2
Voice-over-IP Configuration Examples 4-3
FXS-to-FXS Connection Using RSVP 4-4
Configuration for Router RLB-1 4-4
Configuration for Router RLB-w 4-5
Configuration for Router R12-e 4-5
Configuration for Router RLB-2 4-6
Linking PBX Users with E&M Trunk Lines 4-6
Router SJ Configuration 4-7
Router SLC Configuration 4-8
PSTN Gateway Access Using FXO Connection 4-8
Router SJ Configuration 4-9
Router SLC Configuration 4-9
PSTN Gateway Access Using FXO Connection (PLAR Mode) 4-10
Router SJ Configuration 4-10
Router SLC Configuration 4-11
Configuring Direct-Inward Dialing on a BRI Port 4-11