Specifications
Table Of Contents
- Software Configuration Guide
- Contents
- Preface
- Understanding Interface Numbering and Cisco IOS Software Basics
- Understanding Interface Numbering
- Understanding Cisco IOS Software Basics
- Upgrading to a New Cisco IOS Release
- Where to Go Next
- Using the Setup Command Facility
- Before Starting Your Router
- Using the setup Command Facility
- Configuring Global Parameters
- Configuring Interface Parameters
- Completing the Configuration
- Where to Go Next
- Configuring with the Command-Line Interface
- Configuring the Host Name and Password
- Configuring 1-Port and 2-Port Ethernet Interfaces
- Configuring Fast Ethernet Interfaces
- Configuring Asynchronous/Synchronous Serial Network Modules or WAN Interface Cards
- Configuring 16-Port and 32-Port Asynchronous Network Modules
- Configuring ISDN BRI WAN Interface Cards
- Configuring T1 and E1 Interfaces
- Configuring T1 (FT1) WAN Interface Cards
- Configuring ATM Interfaces
- Configuring Inverse Multiplexing for ATM Interfaces
- Configuring Analog Modem Interfaces
- Configuring Wireless Multipoint Interfaces
- Checking the Interface Configuration
- Configuring 1-Port ADSL WAN Interface Card
- Configuring the NM-AIC-64, Contact Closure Network Module
- Configuring the 1-Port HSSI Network Module
- Configuring the Compression Network Module for the Cisco 3600 Series Routers
- Configuring the Digital Modem Network Module for the Cisco 3640 Router
- Prerequisites
- Configuration Tasks
- Configure the E1/T1 Network Module for ISDN PRI
- Configure the ISDN D-Channel Serial Interfaces
- Configure the Loopback Interface
- Configure the LAN Interface
- Create the Group Asynchronous Interface
- Configure the ISDN Dialer Interface
- Configure the Default IP Pool Information
- Configure Modem Lines for Dial-In and Dial-Out
- Configuration Example
- Configuring 1-Port G.SHDSL WAN Interface Card
- Saving Configuration Changes
- Where to Go Next
- Configuring Voice-over-IP
- Voice-over-IP Prerequisites
- Configuring the Voice Interface
- Voice-over-IP Configuration Examples
- Where to Go Next
- Configuration Examples
- Cisco 2600 Series Router Configuration Example
- Cisco 3631 Router Configuration Example
- Cisco 3725 Router Configuration Example
- 1-Port ADSL WAN Interface Card Configuration Examples
- NM-AIC-64, Contact Closure NetworkConfiguration Examples
- Cisco 3640 Central Site Configuration to Support ISDN and Modem Calls
- Formatting the Compact Flash Memory Cards
- Using the ROM Monitor
- Index
Contents
vi
Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers
OL-1957-03
Serial Communication Channels 3-35
Serial Data Channel 3-36
Asynchronous Craft Port 3-36
Configuring the AIC 3-36
Configuration Tasks 3-37
Configuring the AIC 3-38
Accessing the AIC 3-40
Configuring the NOC IP Address 3-40
Configuring Alarms 3-41
Programming the Analog Contact Points 3-41
Programming the Discrete Contact Points 3-43
Verifying the IP Address 3-43
Troubleshooting Tips 3-45
Monitoring and Maintaining the NM-AIC-64 Contact Closure Network Module 3-45
Software Upgrade 3-45
Configuration Backup 3-46
Override 3-46
Configuration Examples 3-46
Configuring the 1-Port HSSI Network Module 3-46
Configuration Tasks 3-47
Specify a HSSI 3-47
Specify HSSI Encapsulation 3-47
Invoke ATM on a HSSI Line 3-48
Convert HSSI to Clock Master 3-48
Disable Fair Queueing 3-48
Configuration Examples 3-48
Configuring the Compression Network Module for the
Cisco 3600 Series Routers
3-49
Configuration Task 3-49
Configuration Example 3-50
Configuring the Digital Modem Network Module for the
Cisco 3640 Router
3-50
Prerequisites 3-51
Configuration Tasks 3-51
Configure the E1/T1 Network Module for ISDN PRI 3-52
Configure Channelized E1 ISDN PRI 3-52
Configure Channelized T1 ISDN PRI 3-53
Configure the ISDN D-Channel Serial Interfaces 3-53
Configure the ISDN D-Channel Serial Interface for E1 Modules 3-54
Configure the ISDN D-Channel Serial Interface for T1 Modules 3-54