Specifications
Table Of Contents
- Software Configuration Guide
- Contents
- Preface
- Understanding Interface Numbering and Cisco IOS Software Basics
- Understanding Interface Numbering
- Understanding Cisco IOS Software Basics
- Upgrading to a New Cisco IOS Release
- Where to Go Next
- Using the Setup Command Facility
- Before Starting Your Router
- Using the setup Command Facility
- Configuring Global Parameters
- Configuring Interface Parameters
- Completing the Configuration
- Where to Go Next
- Configuring with the Command-Line Interface
- Configuring the Host Name and Password
- Configuring 1-Port and 2-Port Ethernet Interfaces
- Configuring Fast Ethernet Interfaces
- Configuring Asynchronous/Synchronous Serial Network Modules or WAN Interface Cards
- Configuring 16-Port and 32-Port Asynchronous Network Modules
- Configuring ISDN BRI WAN Interface Cards
- Configuring T1 and E1 Interfaces
- Configuring T1 (FT1) WAN Interface Cards
- Configuring ATM Interfaces
- Configuring Inverse Multiplexing for ATM Interfaces
- Configuring Analog Modem Interfaces
- Configuring Wireless Multipoint Interfaces
- Checking the Interface Configuration
- Configuring 1-Port ADSL WAN Interface Card
- Configuring the NM-AIC-64, Contact Closure Network Module
- Configuring the 1-Port HSSI Network Module
- Configuring the Compression Network Module for the Cisco 3600 Series Routers
- Configuring the Digital Modem Network Module for the Cisco 3640 Router
- Prerequisites
- Configuration Tasks
- Configure the E1/T1 Network Module for ISDN PRI
- Configure the ISDN D-Channel Serial Interfaces
- Configure the Loopback Interface
- Configure the LAN Interface
- Create the Group Asynchronous Interface
- Configure the ISDN Dialer Interface
- Configure the Default IP Pool Information
- Configure Modem Lines for Dial-In and Dial-Out
- Configuration Example
- Configuring 1-Port G.SHDSL WAN Interface Card
- Saving Configuration Changes
- Where to Go Next
- Configuring Voice-over-IP
- Voice-over-IP Prerequisites
- Configuring the Voice Interface
- Voice-over-IP Configuration Examples
- Where to Go Next
- Configuration Examples
- Cisco 2600 Series Router Configuration Example
- Cisco 3631 Router Configuration Example
- Cisco 3725 Router Configuration Example
- 1-Port ADSL WAN Interface Card Configuration Examples
- NM-AIC-64, Contact Closure NetworkConfiguration Examples
- Cisco 3640 Central Site Configuration to Support ISDN and Modem Calls
- Formatting the Compact Flash Memory Cards
- Using the ROM Monitor
- Index
2-14
Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers
OL-1957-03
Chapter 2 Using the Setup Command Facility
Configuring Interface Parameters
Note If your router does not have a configured LAN interface, you must use a numbered IP address.
IP address for this interface: 2.0.0.0.1
Enter the subnet mask [255.0.0.0]:
PPP Encapsulation
Would you like to enable multilink PPP [yes]:
Enter a remote hostname for PPP authentication [Router]:
Enter a password for PPP authentication:
Note The password, which is used by the Challenge Handshake Authentication Protocol (CHAP)
authentication process, is case sensitive and must match the remote router’s password exactly.
Frame Relay Encapsulation
The following lmi-types are available to be set,
when connected to a frame relay switch
[0] none
[1] ansi
[2] cisco
[3] q933a
Enter lmi-type [2]:
Note The setup command facility only prompts for the data-link connection identifier (DLCI) number if
you specify none for the Local Management Interface (LMI) type. If you accept the default or specify
another LMI type, the DLCI number is provided by the specified protocol.
Enter the DLCI number for this interface [16]:
Do you want to map a remote machine’s IP address to dlci? [yes]:
IP address for the remote interface: 2.0.0.2
Do you want to map a remote machine’s IPX address to dlci? [yes]:
IPX address for the remote interface: 40.1234.5678
Serial interface needs clock rate to be set in dce mode.
The following clock rates are supported on the serial interface.
0
1200, 2400, 4800, 9600, 19200, 38400
56000, 64000, 72000, 125000, 148000, 500000
800000, 1000000, 1300000, 2000000, 4000000, 8000000
choose speed from above: [2000000]: 1200
Configure IP on this interface? [yes]:
IP address for this interface: 2.0.0.1
Subnet mask for this interface [255.0.0.0]:
Class A network is 2.0.0.0, 8 subnet bits; mask is /8
Note If IPX is configured on the router, the setup command facility prompts for the IPX map:
Do you want to map a remote machine's IPX address to dlci? [yes]:
IPX address for the remote interface: 40.0060.34c6.90ed