Specifications
Table Of Contents
- Software Configuration Guide
- Contents
- Preface
- Understanding Interface Numbering and Cisco IOS Software Basics
- Understanding Interface Numbering
- Understanding Cisco IOS Software Basics
- Upgrading to a New Cisco IOS Release
- Where to Go Next
- Using the Setup Command Facility
- Before Starting Your Router
- Using the setup Command Facility
- Configuring Global Parameters
- Configuring Interface Parameters
- Completing the Configuration
- Where to Go Next
- Configuring with the Command-Line Interface
- Configuring the Host Name and Password
- Configuring 1-Port and 2-Port Ethernet Interfaces
- Configuring Fast Ethernet Interfaces
- Configuring Asynchronous/Synchronous Serial Network Modules or WAN Interface Cards
- Configuring 16-Port and 32-Port Asynchronous Network Modules
- Configuring ISDN BRI WAN Interface Cards
- Configuring T1 and E1 Interfaces
- Configuring T1 (FT1) WAN Interface Cards
- Configuring ATM Interfaces
- Configuring Inverse Multiplexing for ATM Interfaces
- Configuring Analog Modem Interfaces
- Configuring Wireless Multipoint Interfaces
- Checking the Interface Configuration
- Configuring 1-Port ADSL WAN Interface Card
- Configuring the NM-AIC-64, Contact Closure Network Module
- Configuring the 1-Port HSSI Network Module
- Configuring the Compression Network Module for the Cisco 3600 Series Routers
- Configuring the Digital Modem Network Module for the Cisco 3640 Router
- Prerequisites
- Configuration Tasks
- Configure the E1/T1 Network Module for ISDN PRI
- Configure the ISDN D-Channel Serial Interfaces
- Configure the Loopback Interface
- Configure the LAN Interface
- Create the Group Asynchronous Interface
- Configure the ISDN Dialer Interface
- Configure the Default IP Pool Information
- Configure Modem Lines for Dial-In and Dial-Out
- Configuration Example
- Configuring 1-Port G.SHDSL WAN Interface Card
- Saving Configuration Changes
- Where to Go Next
- Configuring Voice-over-IP
- Voice-over-IP Prerequisites
- Configuring the Voice Interface
- Voice-over-IP Configuration Examples
- Where to Go Next
- Configuration Examples
- Cisco 2600 Series Router Configuration Example
- Cisco 3631 Router Configuration Example
- Cisco 3725 Router Configuration Example
- 1-Port ADSL WAN Interface Card Configuration Examples
- NM-AIC-64, Contact Closure NetworkConfiguration Examples
- Cisco 3640 Central Site Configuration to Support ISDN and Modem Calls
- Formatting the Compact Flash Memory Cards
- Using the ROM Monitor
- Index
2-6
Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers
OL-1957-03
Chapter 2 Using the Setup Command Facility
Configuring Interface Parameters
Configuring Interface Parameters
From this point on in the setup process, the prompts you see vary depending on the network modules
and WAN interface cards in place in your router. The following sections provide examples of the setup
steps for each interface module. Refer to the sections appropriate to your router.
Configuration for network modules includes:
• Ethernet Interface Configuration, page 2-6
• FastEthernet Interface Configuration, page 2-6
• Token Ring Interface Configuration, page 2-7
• Serial Interface Configuration, page 2-7
• Asynchronous/Synchronous Serial Interface Configuration, page 2-10
• ISDN BRI Interface Configuration, page 2-12
• E1/T1 ISDN PRI Configuration, page 2-18
–
E1/T1 PRI Mode, page 2-18
–
E1 Channelized Mode, page 2-18
–
T1 Channelized Mode, page 2-21
• 1-Port, 4-Wire 56-kbps DSU/CSU Configuration Setup, page 2-22
When you complete the setup steps for your interface modules, go to the “Completing the Configuration”
section on page 2-24 for directions on saving your configuration.
Ethernet Interface Configuration
This section contains a sample configuration for the Ethernet interface. Enter the values appropriate for
your router and network. The messages you see may vary.
Do you want to configure Ethernet0/0 interface [yes]:
Configure IP on this interface? [yes]:
IP address for this interface: 255.255.255.0
Subnet mask for this interface [255.0.0.0]:
Class A network is 1.0.0.0, 8 subnet bits, mask is /8
Configure IPX on this interface? [no]: y
IPX network number [1]:
Need to select encapsulation type
[0] sap (IEEE 802.2)
[1] snap (IEEE 802.2 SNAP)
[2] arpa (Ethernet_II)
[3] novell-ether (Novell Ethernet_802.3)
Enter the encapsulation type [2]:
FastEthernet Interface Configuration
This section contains a sample configuration for the FastEthernet interface. Enter the values appropriate
for your router and network. The messages you see may vary.
Do you want to configure FastEthernet0/0 interface [yes]:
Use the 100 Base-TX (RJ-45) connector? [yes]:
Operate in full-duplex mode? [no]:
Configure IP on this interface? [no]: yes
IP address for this interface: 6.0.0.1