Specifications
Table Of Contents
- Software Configuration Guide
- Contents
- Preface
- Understanding Interface Numbering and Cisco IOS Software Basics
- Understanding Interface Numbering
- Understanding Cisco IOS Software Basics
- Upgrading to a New Cisco IOS Release
- Where to Go Next
- Using the Setup Command Facility
- Before Starting Your Router
- Using the setup Command Facility
- Configuring Global Parameters
- Configuring Interface Parameters
- Completing the Configuration
- Where to Go Next
- Configuring with the Command-Line Interface
- Configuring the Host Name and Password
- Configuring 1-Port and 2-Port Ethernet Interfaces
- Configuring Fast Ethernet Interfaces
- Configuring Asynchronous/Synchronous Serial Network Modules or WAN Interface Cards
- Configuring 16-Port and 32-Port Asynchronous Network Modules
- Configuring ISDN BRI WAN Interface Cards
- Configuring T1 and E1 Interfaces
- Configuring T1 (FT1) WAN Interface Cards
- Configuring ATM Interfaces
- Configuring Inverse Multiplexing for ATM Interfaces
- Configuring Analog Modem Interfaces
- Configuring Wireless Multipoint Interfaces
- Checking the Interface Configuration
- Configuring 1-Port ADSL WAN Interface Card
- Configuring the NM-AIC-64, Contact Closure Network Module
- Configuring the 1-Port HSSI Network Module
- Configuring the Compression Network Module for the Cisco 3600 Series Routers
- Configuring the Digital Modem Network Module for the Cisco 3640 Router
- Prerequisites
- Configuration Tasks
- Configure the E1/T1 Network Module for ISDN PRI
- Configure the ISDN D-Channel Serial Interfaces
- Configure the Loopback Interface
- Configure the LAN Interface
- Create the Group Asynchronous Interface
- Configure the ISDN Dialer Interface
- Configure the Default IP Pool Information
- Configure Modem Lines for Dial-In and Dial-Out
- Configuration Example
- Configuring 1-Port G.SHDSL WAN Interface Card
- Saving Configuration Changes
- Where to Go Next
- Configuring Voice-over-IP
- Voice-over-IP Prerequisites
- Configuring the Voice Interface
- Voice-over-IP Configuration Examples
- Where to Go Next
- Configuration Examples
- Cisco 2600 Series Router Configuration Example
- Cisco 3631 Router Configuration Example
- Cisco 3725 Router Configuration Example
- 1-Port ADSL WAN Interface Card Configuration Examples
- NM-AIC-64, Contact Closure NetworkConfiguration Examples
- Cisco 3640 Central Site Configuration to Support ISDN and Modem Calls
- Formatting the Compact Flash Memory Cards
- Using the ROM Monitor
- Index
Contents
iv
Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers
OL-1957-03
Getting Help 1-13
Understanding Command Modes 1-14
Undoing a Command or Feature 1-15
Saving Configuration Changes 1-15
Upgrading to a New Cisco IOS Release 1-15
Where to Go Next 1-15
CHAPTER
2 Using the Setup Command Facility 2-1
Before Starting Your Router 2-1
Using the setup Command Facility 2-2
Configuring Global Parameters 2-2
Configuring Interface Parameters 2-6
Ethernet Interface Configuration 2-6
FastEthernet Interface Configuration 2-6
Token Ring Interface Configuration 2-7
Serial Interface Configuration 2-7
Frame Relay Encapsulation 2-8
LAPB Encapsulation 2-8
X.25 Encapsulation 2-9
ATM-DXI Encapsulation 2-9
SMDS Encapsulation 2-9
Serial Cisco IOS Commands Generated 2-9
Asynchronous/Synchronous Serial Interface Configuration 2-10
Synchronous Configuration 2-10
Asynchronous Configuration 2-12
ISDN BRI Interface Configuration 2-12
ISDN BRI Line Configuration 2-15
ISDN BRI Provisioning by Switch Type 2-16
Defining ISDN Service Profile Identifiers 2-17
E1/T1 ISDN PRI Configuration 2-18
E1/T1 PRI Mode 2-18
E1 Channelized Mode 2-18
T1 Channelized Mode 2-21
1-Port, 4-Wire 56-kbps DSU/CSU Configuration Setup 2-22
Choosing Circuit-Switched or Dedicated-Line Service 2-23
Switched Mode 2-23
Dedicated Mode 2-23
Completing the Configuration 2-24
Where to Go Next 2-25