Specifications
Table Of Contents
- Software Configuration Guide
- Contents
- Preface
- Understanding Interface Numbering and Cisco IOS Software Basics
- Understanding Interface Numbering
- Understanding Cisco IOS Software Basics
- Upgrading to a New Cisco IOS Release
- Where to Go Next
- Using the Setup Command Facility
- Before Starting Your Router
- Using the setup Command Facility
- Configuring Global Parameters
- Configuring Interface Parameters
- Completing the Configuration
- Where to Go Next
- Configuring with the Command-Line Interface
- Configuring the Host Name and Password
- Configuring 1-Port and 2-Port Ethernet Interfaces
- Configuring Fast Ethernet Interfaces
- Configuring Asynchronous/Synchronous Serial Network Modules or WAN Interface Cards
- Configuring 16-Port and 32-Port Asynchronous Network Modules
- Configuring ISDN BRI WAN Interface Cards
- Configuring T1 and E1 Interfaces
- Configuring T1 (FT1) WAN Interface Cards
- Configuring ATM Interfaces
- Configuring Inverse Multiplexing for ATM Interfaces
- Configuring Analog Modem Interfaces
- Configuring Wireless Multipoint Interfaces
- Checking the Interface Configuration
- Configuring 1-Port ADSL WAN Interface Card
- Configuring the NM-AIC-64, Contact Closure Network Module
- Configuring the 1-Port HSSI Network Module
- Configuring the Compression Network Module for the Cisco 3600 Series Routers
- Configuring the Digital Modem Network Module for the Cisco 3640 Router
- Prerequisites
- Configuration Tasks
- Configure the E1/T1 Network Module for ISDN PRI
- Configure the ISDN D-Channel Serial Interfaces
- Configure the Loopback Interface
- Configure the LAN Interface
- Create the Group Asynchronous Interface
- Configure the ISDN Dialer Interface
- Configure the Default IP Pool Information
- Configure Modem Lines for Dial-In and Dial-Out
- Configuration Example
- Configuring 1-Port G.SHDSL WAN Interface Card
- Saving Configuration Changes
- Where to Go Next
- Configuring Voice-over-IP
- Voice-over-IP Prerequisites
- Configuring the Voice Interface
- Voice-over-IP Configuration Examples
- Where to Go Next
- Configuration Examples
- Cisco 2600 Series Router Configuration Example
- Cisco 3631 Router Configuration Example
- Cisco 3725 Router Configuration Example
- 1-Port ADSL WAN Interface Card Configuration Examples
- NM-AIC-64, Contact Closure NetworkConfiguration Examples
- Cisco 3640 Central Site Configuration to Support ISDN and Modem Calls
- Formatting the Compact Flash Memory Cards
- Using the ROM Monitor
- Index
Index
IN-4
Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers
OL-1957-03
ISDN BRI
switch type, provisioning
2-16
ISDN BRI interface, configuring 3-10
ISDN BRI line, configuring 2-15
ISDN PRI interface
configuring
3-15
E1 configuration 3-16
T1 configuration 3-15
ISDN PRI switch types 3-52
ISDN provisioning by switch type (table) 2-16
ISDN switch types 3-12
L
LAN Interface Numbering
Cisco 2600 series router
1-2
M
meminfo command C-3
modem country codes 3-28
multiflex trunk interface
configuring
3-15
E1 configuration 3-16
T1 configuration 3-15
TDM connect 3-17
N
network modules
configuring
asynchronous/synchronous interface
2-10
E1/T1 ISDN PRI interface 2-18
Ethernet interface 2-6
Fast Ethernet interface 2-6
ISDN BRI interface 2-12
serial interface 2-7
Token Ring interface 2-7
note symbol, meaning of xiii
P
parameters
configuring global
2-2
configuring interface 2-6
password
configuring
3-2
show config command 3-3
verifying 3-3
PPP
compression
3-49
prerequisites 3-51
privileged EXEC command mode 1-14
provisioning ISDN switch types 2-16
PVC configuration 3-21
R
recovering boot and system images C-8
reset command C-4
ROM
monitor
diagnostics
C-5
router
rear view
Cisco 3620 (figure)
1-5
Cisco 3631 (figure) 1-6
Cisco 3640 (figure) 1-5
Cisco 3660 (figure) 1-5
S
saving configuration changes 1-15, 3-65
script, setup 2-2
service profile identifier
See SPID