Specifications
Table Of Contents
- Software Configuration Guide
- Contents
- Preface
- Understanding Interface Numbering and Cisco IOS Software Basics
- Understanding Interface Numbering
- Understanding Cisco IOS Software Basics
- Upgrading to a New Cisco IOS Release
- Where to Go Next
- Using the Setup Command Facility
- Before Starting Your Router
- Using the setup Command Facility
- Configuring Global Parameters
- Configuring Interface Parameters
- Completing the Configuration
- Where to Go Next
- Configuring with the Command-Line Interface
- Configuring the Host Name and Password
- Configuring 1-Port and 2-Port Ethernet Interfaces
- Configuring Fast Ethernet Interfaces
- Configuring Asynchronous/Synchronous Serial Network Modules or WAN Interface Cards
- Configuring 16-Port and 32-Port Asynchronous Network Modules
- Configuring ISDN BRI WAN Interface Cards
- Configuring T1 and E1 Interfaces
- Configuring T1 (FT1) WAN Interface Cards
- Configuring ATM Interfaces
- Configuring Inverse Multiplexing for ATM Interfaces
- Configuring Analog Modem Interfaces
- Configuring Wireless Multipoint Interfaces
- Checking the Interface Configuration
- Configuring 1-Port ADSL WAN Interface Card
- Configuring the NM-AIC-64, Contact Closure Network Module
- Configuring the 1-Port HSSI Network Module
- Configuring the Compression Network Module for the Cisco 3600 Series Routers
- Configuring the Digital Modem Network Module for the Cisco 3640 Router
- Prerequisites
- Configuration Tasks
- Configure the E1/T1 Network Module for ISDN PRI
- Configure the ISDN D-Channel Serial Interfaces
- Configure the Loopback Interface
- Configure the LAN Interface
- Create the Group Asynchronous Interface
- Configure the ISDN Dialer Interface
- Configure the Default IP Pool Information
- Configure Modem Lines for Dial-In and Dial-Out
- Configuration Example
- Configuring 1-Port G.SHDSL WAN Interface Card
- Saving Configuration Changes
- Where to Go Next
- Configuring Voice-over-IP
- Voice-over-IP Prerequisites
- Configuring the Voice Interface
- Voice-over-IP Configuration Examples
- Where to Go Next
- Configuration Examples
- Cisco 2600 Series Router Configuration Example
- Cisco 3631 Router Configuration Example
- Cisco 3725 Router Configuration Example
- 1-Port ADSL WAN Interface Card Configuration Examples
- NM-AIC-64, Contact Closure NetworkConfiguration Examples
- Cisco 3640 Central Site Configuration to Support ISDN and Modem Calls
- Formatting the Compact Flash Memory Cards
- Using the ROM Monitor
- Index
Index
IN-3
Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers
OL-1957-03
T1 (FT1) WAN interface 3-19
T1 interface 3-15
context command C-5
conventions xii
conventions, document xii
D
debugging commands C-5
dir command C-3
document
conventions
xii
document conventions xii
E
E1/T1 ISDN PRI interface 3-15, 3-16
E1/T1 multiflex trunk interface 3-15, 3-16
E1 interface
configuring
3-15
enable mode 1-15
encapsulation atm-dxi command 3-48
encapsulation ppp command
configuring compression over
3-50
Ethernet interface, configuring 2-6, 3-3
F
feature summary 3-50
frame command C-5
G
global configuration command mode 1-14
global parameters configuration 2-2
H
half-duplex timer commands 3-8
hardware compression, displaying 3-49
help
command
C-3
help, Cisco IOS 1-13
high-density voice interface
codec complexity
3-18
host name
configuring
3-2
show config command 3-3
verifying 3-3
hssi internal-clock command 3-48
HSSI network module
benefits
3-47
configuration
disabling fair queueing
3-48
examples 3-48
invoking ATM 3-48
specifying clocking 3-48
specifying encapsulation 3-47
specifying interface 3-47
task list 3-47
feature summary 3-46
I
IMA interface
configuring
3-23
configuring the ATM T1/E1 interface 3-23
configuring the IMA interface 3-25
IMA interface configuration 3-25
interface configuration command mode 1-14
interface numbering
Cisco 2600 series routers
1-1
Cisco 3600 series routers 1-4
Cisco 3660 slot 0 1-6, 1-8
WAN and LAN interface cards 1-2