Specifications
Table Of Contents
- Software Configuration Guide
- Contents
- Preface
- Understanding Interface Numbering and Cisco IOS Software Basics
- Understanding Interface Numbering
- Understanding Cisco IOS Software Basics
- Upgrading to a New Cisco IOS Release
- Where to Go Next
- Using the Setup Command Facility
- Before Starting Your Router
- Using the setup Command Facility
- Configuring Global Parameters
- Configuring Interface Parameters
- Completing the Configuration
- Where to Go Next
- Configuring with the Command-Line Interface
- Configuring the Host Name and Password
- Configuring 1-Port and 2-Port Ethernet Interfaces
- Configuring Fast Ethernet Interfaces
- Configuring Asynchronous/Synchronous Serial Network Modules or WAN Interface Cards
- Configuring 16-Port and 32-Port Asynchronous Network Modules
- Configuring ISDN BRI WAN Interface Cards
- Configuring T1 and E1 Interfaces
- Configuring T1 (FT1) WAN Interface Cards
- Configuring ATM Interfaces
- Configuring Inverse Multiplexing for ATM Interfaces
- Configuring Analog Modem Interfaces
- Configuring Wireless Multipoint Interfaces
- Checking the Interface Configuration
- Configuring 1-Port ADSL WAN Interface Card
- Configuring the NM-AIC-64, Contact Closure Network Module
- Configuring the 1-Port HSSI Network Module
- Configuring the Compression Network Module for the Cisco 3600 Series Routers
- Configuring the Digital Modem Network Module for the Cisco 3640 Router
- Prerequisites
- Configuration Tasks
- Configure the E1/T1 Network Module for ISDN PRI
- Configure the ISDN D-Channel Serial Interfaces
- Configure the Loopback Interface
- Configure the LAN Interface
- Create the Group Asynchronous Interface
- Configure the ISDN Dialer Interface
- Configure the Default IP Pool Information
- Configure Modem Lines for Dial-In and Dial-Out
- Configuration Example
- Configuring 1-Port G.SHDSL WAN Interface Card
- Saving Configuration Changes
- Where to Go Next
- Configuring Voice-over-IP
- Voice-over-IP Prerequisites
- Configuring the Voice Interface
- Voice-over-IP Configuration Examples
- Where to Go Next
- Configuration Examples
- Cisco 2600 Series Router Configuration Example
- Cisco 3631 Router Configuration Example
- Cisco 3725 Router Configuration Example
- 1-Port ADSL WAN Interface Card Configuration Examples
- NM-AIC-64, Contact Closure NetworkConfiguration Examples
- Cisco 3640 Central Site Configuration to Support ISDN and Modem Calls
- Formatting the Compact Flash Memory Cards
- Using the ROM Monitor
- Index
IN-1
Software Configuration Guide For Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers
OL-1957-03
INDEX
Numerics
56-kbps DSU/CSU interface, configuring 2-22
A
analog modem interface
configuring
3-26
modem country codes 3-28
asynchronous/synchronous serial interface
configuring
3-5
asynchronous interface, configuring 3-9
atm-dxi map command 3-48
ATM interface
configuring
3-20
configuring PVCs 3-21
configuring SVCs 3-22
IMA interface configuration 3-23
ATM T1/E1 interface configuration 3-23
B
benefits 3-50
boot
ROM monitor
C-3
C
caution symbol, meaning of xiii
Cisco 2600 series router
WAN Interface Numbering
1-2
Cisco 2600 series routers
interface numbering
1-1
Voice Interface Numbering 1-4
Cisco 3600 series routers
interface numbering
1-4
unit numbers (figure) 1-9
Cisco 3700 Series Interface Numbering 1-9
Cisco 3725 Interface Numbering 1-9
Cisco 3745 router interface numbering 1-11
Cisco IOS
about
1-13
command modes 1-14
enable mode 1-15
getting help 1-13
saving configuration changes 1-15
undo command 1-15
undo feature 1-15
clock rate settings 3-8
codec complexity configuration 3-18
command modes, Cisco IOS 1-14
commands
configuration register
C-5
context C-5
copy running-config 1-15
debugging C-5
dir C-3
exec-timeout 3-2
frame C-5
half-duplex timer 3-8
help 1-13, C-3
meminfo C-3
ping 3-29
reset C-4