Specifications
Table Of Contents
- Software Configuration Guide
- Contents
- Preface
- Understanding Interface Numbering and Cisco IOS Software Basics
- Understanding Interface Numbering
- Understanding Cisco IOS Software Basics
- Upgrading to a New Cisco IOS Release
- Where to Go Next
- Using the Setup Command Facility
- Before Starting Your Router
- Using the setup Command Facility
- Configuring Global Parameters
- Configuring Interface Parameters
- Completing the Configuration
- Where to Go Next
- Configuring with the Command-Line Interface
- Configuring the Host Name and Password
- Configuring 1-Port and 2-Port Ethernet Interfaces
- Configuring Fast Ethernet Interfaces
- Configuring Asynchronous/Synchronous Serial Network Modules or WAN Interface Cards
- Configuring 16-Port and 32-Port Asynchronous Network Modules
- Configuring ISDN BRI WAN Interface Cards
- Configuring T1 and E1 Interfaces
- Configuring T1 (FT1) WAN Interface Cards
- Configuring ATM Interfaces
- Configuring Inverse Multiplexing for ATM Interfaces
- Configuring Analog Modem Interfaces
- Configuring Wireless Multipoint Interfaces
- Checking the Interface Configuration
- Configuring 1-Port ADSL WAN Interface Card
- Configuring the NM-AIC-64, Contact Closure Network Module
- Configuring the 1-Port HSSI Network Module
- Configuring the Compression Network Module for the Cisco 3600 Series Routers
- Configuring the Digital Modem Network Module for the Cisco 3640 Router
- Prerequisites
- Configuration Tasks
- Configure the E1/T1 Network Module for ISDN PRI
- Configure the ISDN D-Channel Serial Interfaces
- Configure the Loopback Interface
- Configure the LAN Interface
- Create the Group Asynchronous Interface
- Configure the ISDN Dialer Interface
- Configure the Default IP Pool Information
- Configure Modem Lines for Dial-In and Dial-Out
- Configuration Example
- Configuring 1-Port G.SHDSL WAN Interface Card
- Saving Configuration Changes
- Where to Go Next
- Configuring Voice-over-IP
- Voice-over-IP Prerequisites
- Configuring the Voice Interface
- Voice-over-IP Configuration Examples
- Where to Go Next
- Configuration Examples
- Cisco 2600 Series Router Configuration Example
- Cisco 3631 Router Configuration Example
- Cisco 3725 Router Configuration Example
- 1-Port ADSL WAN Interface Card Configuration Examples
- NM-AIC-64, Contact Closure NetworkConfiguration Examples
- Cisco 3640 Central Site Configuration to Support ISDN and Modem Calls
- Formatting the Compact Flash Memory Cards
- Using the ROM Monitor
- Index
A-13
Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers
OL-1957-03
Appendix A Configuration Examples
1-Port ADSL WAN Interface Card Configuration Examples
dsl operating-mode ansi-dmt
no fair-queue
!
interface Ethernet0/1
no ip address
shutdown
!
ip classless
ip route 223.255.254.254 255.255.255.224 Ethernet0/0
no ip http server
!
!
snmp-server engineID local 000000090200003080477F20
snmp-server manager
!
voice-port 1/0:0
local-alerting
timeouts wait-release 3
connection trunk 3001
!
voice-port 1/0:1
local-alerting
timeouts wait-release 3
connection trunk 3002
.
.
.
voice-port 1/0:23
local-alerting
timeouts wait-release 3
connection trunk 3024
shutdown
!
dial-peer cor custom
!
dial-peer voice 3001 voatm
destination-pattern 3001
called-number 4001
session protocol aal2-trunk
session target ATM0/1 pvc 10/100 31
codec aal2-profile ITUT 1 g711ulaw
no vad
!
dial-peer voice 3002 voatm
destination-pattern 3002
called-number 4002
session protocol aal2-trunk
session target ATM0/1 pvc 10/100 32
codec aal2-profile custom 100 g726r32
no vad
!
dial-peer voice 3003 voatm
destination-pattern 3003
called-number 4003
session protocol aal2-trunk
session target ATM0/1 pvc 10/100 33
codec aal2-profile ITUT 7 g729abr8
no vad
.
.
.
dial-peer voice 3024 voatm
destination-pattern 3024
called-number 3024