Specifications
Table Of Contents
- Software Configuration Guide
- Contents
- Preface
- Understanding Interface Numbering and Cisco IOS Software Basics
- Understanding Interface Numbering
- Understanding Cisco IOS Software Basics
- Upgrading to a New Cisco IOS Release
- Where to Go Next
- Using the Setup Command Facility
- Before Starting Your Router
- Using the setup Command Facility
- Configuring Global Parameters
- Configuring Interface Parameters
- Completing the Configuration
- Where to Go Next
- Configuring with the Command-Line Interface
- Configuring the Host Name and Password
- Configuring 1-Port and 2-Port Ethernet Interfaces
- Configuring Fast Ethernet Interfaces
- Configuring Asynchronous/Synchronous Serial Network Modules or WAN Interface Cards
- Configuring 16-Port and 32-Port Asynchronous Network Modules
- Configuring ISDN BRI WAN Interface Cards
- Configuring T1 and E1 Interfaces
- Configuring T1 (FT1) WAN Interface Cards
- Configuring ATM Interfaces
- Configuring Inverse Multiplexing for ATM Interfaces
- Configuring Analog Modem Interfaces
- Configuring Wireless Multipoint Interfaces
- Checking the Interface Configuration
- Configuring 1-Port ADSL WAN Interface Card
- Configuring the NM-AIC-64, Contact Closure Network Module
- Configuring the 1-Port HSSI Network Module
- Configuring the Compression Network Module for the Cisco 3600 Series Routers
- Configuring the Digital Modem Network Module for the Cisco 3640 Router
- Prerequisites
- Configuration Tasks
- Configure the E1/T1 Network Module for ISDN PRI
- Configure the ISDN D-Channel Serial Interfaces
- Configure the Loopback Interface
- Configure the LAN Interface
- Create the Group Asynchronous Interface
- Configure the ISDN Dialer Interface
- Configure the Default IP Pool Information
- Configure Modem Lines for Dial-In and Dial-Out
- Configuration Example
- Configuring 1-Port G.SHDSL WAN Interface Card
- Saving Configuration Changes
- Where to Go Next
- Configuring Voice-over-IP
- Voice-over-IP Prerequisites
- Configuring the Voice Interface
- Voice-over-IP Configuration Examples
- Where to Go Next
- Configuration Examples
- Cisco 2600 Series Router Configuration Example
- Cisco 3631 Router Configuration Example
- Cisco 3725 Router Configuration Example
- 1-Port ADSL WAN Interface Card Configuration Examples
- NM-AIC-64, Contact Closure NetworkConfiguration Examples
- Cisco 3640 Central Site Configuration to Support ISDN and Modem Calls
- Formatting the Compact Flash Memory Cards
- Using the ROM Monitor
- Index
A-2
Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers
OL-1957-03
Appendix A Configuration Examples
Cisco 2600 Series Router Configuration Example
no mop enabled
!
interface Serial0/0
encapsulation hdlc
clock rate 2000000
ip address 1.0.0.1 255.0.0.0
lat enabled
appletalk cable-range 3-3 3.3
appletalk zone myzone
ipx network 8
no vines metric
mop enabled
!
interface Ethernet0/1
ip address 255.255.255.1 255.255.0.0
lat enabled
no vines metric
mop enabled
!
interface Serial0/1
physical-layer sync
encapsulation ppp
ip address 2.0.0.1 255.0.0.0
lat enabled
appletalk cable-range 6-6 6.6
appletalk zone myzone
ipx network 6
no vines metric
xns network 7
mop enabled
!
interface Serial0/2
physical-layer async
ip address 3.0.0.1 255.0.0.0
lat enabled
appletalk cable-range 8-8 8.8
appletalk zone myzone
ipx network 8
no vines metric
mop enabled
!
interface Serial1/0
physical-layer sync
encapsulation frame-relay
frame-relay lmi-type cisco
clock rate 115200
ip address 4.0.0.1 255.0.0.0
no lat enabled
no vines metric
no mop enabled
!
interface Serial1/1
physical-layer async
ip address 5.0.0.1 255.0.0.0
no lat enabled
no vines metric
no mop enabled
!
interface Serial1/2
physical-layer sync
encapsulation x25 dte
x25 address 1234
x25 map ip 1.0.0.1 4321
x25 map ipx 6.0.0.1 -2132065964