Specifications
Table Of Contents
- Software Configuration Guide
- Contents
- Preface
- Understanding Interface Numbering and Cisco IOS Software Basics
- Understanding Interface Numbering
- Understanding Cisco IOS Software Basics
- Upgrading to a New Cisco IOS Release
- Where to Go Next
- Using the Setup Command Facility
- Before Starting Your Router
- Using the setup Command Facility
- Configuring Global Parameters
- Configuring Interface Parameters
- Completing the Configuration
- Where to Go Next
- Configuring with the Command-Line Interface
- Configuring the Host Name and Password
- Configuring 1-Port and 2-Port Ethernet Interfaces
- Configuring Fast Ethernet Interfaces
- Configuring Asynchronous/Synchronous Serial Network Modules or WAN Interface Cards
- Configuring 16-Port and 32-Port Asynchronous Network Modules
- Configuring ISDN BRI WAN Interface Cards
- Configuring T1 and E1 Interfaces
- Configuring T1 (FT1) WAN Interface Cards
- Configuring ATM Interfaces
- Configuring Inverse Multiplexing for ATM Interfaces
- Configuring Analog Modem Interfaces
- Configuring Wireless Multipoint Interfaces
- Checking the Interface Configuration
- Configuring 1-Port ADSL WAN Interface Card
- Configuring the NM-AIC-64, Contact Closure Network Module
- Configuring the 1-Port HSSI Network Module
- Configuring the Compression Network Module for the Cisco 3600 Series Routers
- Configuring the Digital Modem Network Module for the Cisco 3640 Router
- Prerequisites
- Configuration Tasks
- Configure the E1/T1 Network Module for ISDN PRI
- Configure the ISDN D-Channel Serial Interfaces
- Configure the Loopback Interface
- Configure the LAN Interface
- Create the Group Asynchronous Interface
- Configure the ISDN Dialer Interface
- Configure the Default IP Pool Information
- Configure Modem Lines for Dial-In and Dial-Out
- Configuration Example
- Configuring 1-Port G.SHDSL WAN Interface Card
- Saving Configuration Changes
- Where to Go Next
- Configuring Voice-over-IP
- Voice-over-IP Prerequisites
- Configuring the Voice Interface
- Voice-over-IP Configuration Examples
- Where to Go Next
- Configuration Examples
- Cisco 2600 Series Router Configuration Example
- Cisco 3631 Router Configuration Example
- Cisco 3725 Router Configuration Example
- 1-Port ADSL WAN Interface Card Configuration Examples
- NM-AIC-64, Contact Closure NetworkConfiguration Examples
- Cisco 3640 Central Site Configuration to Support ISDN and Modem Calls
- Formatting the Compact Flash Memory Cards
- Using the ROM Monitor
- Index
3-59
Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers
OL-1957-03
Chapter 3 Configuring with the Command-Line Interface
Configuring 1-Port G.SHDSL WAN Interface Card
• Configuration Tasks, page 3-60
• Configuration Examples, page 3-64
G.SHDSL is ATM-based, multirate, high-speed (up to 2.3 MB), symmetrical digital subscriber line
digital data transfer between a single customer premises equipment (CPE) subscriber and a central
office.
G.SHDSL is supported on the G.SHDSL WAN interface card, a 1-port WAN interface card (WIC) for
Cisco 2600 series and Cisco 3600 series routers.
The G.SHDSL WIC is compatible with the Cisco 6015, Cisco 6130, Cisco 6160, and Cisco 6260 Digital
Subscriber Line Access Multiplexers (DSLAMs). The DSLAM must be equipped with G.SHDSL line
cards that are compatible with the DSL service to be configured.
The G.SHDSL WIC supports ATM Adaptation Layer 2 (AAL2), ATM Adaptation Layer 5 (AAL5), and
various classes of quality of service (QoS) for both voice and data service.
Listed below are some benefits of this feature:
• Enables business-class broadband service with voice integration, scalable performance, flexibility,
and security.
• Aggregates G.SHDSL and other transport options into a single box.
• Provides G.SHDSL high-speed digital data transmissions between customer premises equipment
(CPE) and the central office (CO), or between routers located within a customer site.
• Supports ITU G.991.2 (SHDSL).
• Supports ANSI T1.601 (BRI), ANSI T1.410 (DDS), and ANSI T1.403 (T1 carrier).
• Supports AAL2 and AAL5 services and applications (including voice), ATM class of service
(constant bit rate [CBR], variable bit rate-nonreal time [VBR-nrt], variable bit rate-real time
[VBR-rt], and unspecified bit rate [UBR and UBR+]), and up to 23 virtual circuits on a WIC in
Cisco 2600 series and Cisco 3600 series routers.
• Provides ATM traffic management and quality of service (QoS) features to enable service providers
to manage their core ATM network infrastructures.
This feature is supported on the following router platforms:
• Cisco 2610
• Cisco 2611
• Cisco 2612
• Cisco 2613
• Cisco 2620
• Cisco 2621
• Cisco 2650
• Cisco 2651
• Cisco 3620
• Cisco 3640
• Cisco 3661
• Cisco 3662