Specifications
Table Of Contents
- Software Configuration Guide
- Contents
- Preface
- Understanding Interface Numbering and Cisco IOS Software Basics
- Understanding Interface Numbering
- Understanding Cisco IOS Software Basics
- Upgrading to a New Cisco IOS Release
- Where to Go Next
- Using the Setup Command Facility
- Before Starting Your Router
- Using the setup Command Facility
- Configuring Global Parameters
- Configuring Interface Parameters
- Completing the Configuration
- Where to Go Next
- Configuring with the Command-Line Interface
- Configuring the Host Name and Password
- Configuring 1-Port and 2-Port Ethernet Interfaces
- Configuring Fast Ethernet Interfaces
- Configuring Asynchronous/Synchronous Serial Network Modules or WAN Interface Cards
- Configuring 16-Port and 32-Port Asynchronous Network Modules
- Configuring ISDN BRI WAN Interface Cards
- Configuring T1 and E1 Interfaces
- Configuring T1 (FT1) WAN Interface Cards
- Configuring ATM Interfaces
- Configuring Inverse Multiplexing for ATM Interfaces
- Configuring Analog Modem Interfaces
- Configuring Wireless Multipoint Interfaces
- Checking the Interface Configuration
- Configuring 1-Port ADSL WAN Interface Card
- Configuring the NM-AIC-64, Contact Closure Network Module
- Configuring the 1-Port HSSI Network Module
- Configuring the Compression Network Module for the Cisco 3600 Series Routers
- Configuring the Digital Modem Network Module for the Cisco 3640 Router
- Prerequisites
- Configuration Tasks
- Configure the E1/T1 Network Module for ISDN PRI
- Configure the ISDN D-Channel Serial Interfaces
- Configure the Loopback Interface
- Configure the LAN Interface
- Create the Group Asynchronous Interface
- Configure the ISDN Dialer Interface
- Configure the Default IP Pool Information
- Configure Modem Lines for Dial-In and Dial-Out
- Configuration Example
- Configuring 1-Port G.SHDSL WAN Interface Card
- Saving Configuration Changes
- Where to Go Next
- Configuring Voice-over-IP
- Voice-over-IP Prerequisites
- Configuring the Voice Interface
- Voice-over-IP Configuration Examples
- Where to Go Next
- Configuration Examples
- Cisco 2600 Series Router Configuration Example
- Cisco 3631 Router Configuration Example
- Cisco 3725 Router Configuration Example
- 1-Port ADSL WAN Interface Card Configuration Examples
- NM-AIC-64, Contact Closure NetworkConfiguration Examples
- Cisco 3640 Central Site Configuration to Support ISDN and Modem Calls
- Formatting the Compact Flash Memory Cards
- Using the ROM Monitor
- Index
3-55
Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers
OL-1957-03
Chapter 3 Configuring with the Command-Line Interface
Configuring the Digital Modem Network Module for the Cisco 3640 Router
For more information about configuring T1 ISDN D-channel serial interfaces, refer to the “Configure
ISDN PRI” section in the Cisco IOS Release 11.3 Dial Solutions Configuration Guide.
Configure the Loopback Interface
The loopback 0 interface is the interface dial-in users access when dialing in to the network. Usually, all
dial-in users are assigned to a single IP subnet. This subnet can be identified with the loopback 0
interface, a logical interface whose network number can be borrowed by each asynchronous dial-in
interface.
To configure the loopback 0 interface, perform the following tasks, beginning in global configuration
mode:
Configure the LAN Interface
The next task you need to perform is to configure the LAN interfaces on your Cisco 3600 series router.
For the purpose of this procedure, we are showing how to configure an Ethernet interface. If the interface
you are configuring is different, refer to the “Configuring LAN Interfaces” chapter in the Cisco IOS
Release 11.3 Configuration Fundamentals Configuration Guide or to the configuration notes that
shippedwith your module.
To configure an Ethernet interface, perform the following tasks, beginning in global configuration mode:
Note The Ethernet and loopback interfaces should be on different subnets.
Create the Group Asynchronous Interface
A group asynchronous interface is a parent interface that applies protocol characteristics to specified,
associated asynchronous interfaces. After you create a group asynchronous interface, all associated
asynchronous interfaces (called members) can be configured through it. Group asynchronous interfaces
can speed configuration time and help you maintain interface configuration consistency.
Command Description
Step 1
interface Loopback number
Select the loopback 0 interface.
Step 2
ip address ip-address ip-address
mask
Assign an IP address and subnet mask to
the loopback 0 interface.
Command Description
Step 1
interface ethernet slot/port
Select the Ethernet interface.
Step 2
ip address ip-address ip-address
mask
Assign an IP address and subnet mask to
the Ethernet interface.
Step 3
no shutdown
Enable this interface