Specifications
Table Of Contents
- Software Configuration Guide
- Contents
- Preface
- Understanding Interface Numbering and Cisco IOS Software Basics
- Understanding Interface Numbering
- Understanding Cisco IOS Software Basics
- Upgrading to a New Cisco IOS Release
- Where to Go Next
- Using the Setup Command Facility
- Before Starting Your Router
- Using the setup Command Facility
- Configuring Global Parameters
- Configuring Interface Parameters
- Completing the Configuration
- Where to Go Next
- Configuring with the Command-Line Interface
- Configuring the Host Name and Password
- Configuring 1-Port and 2-Port Ethernet Interfaces
- Configuring Fast Ethernet Interfaces
- Configuring Asynchronous/Synchronous Serial Network Modules or WAN Interface Cards
- Configuring 16-Port and 32-Port Asynchronous Network Modules
- Configuring ISDN BRI WAN Interface Cards
- Configuring T1 and E1 Interfaces
- Configuring T1 (FT1) WAN Interface Cards
- Configuring ATM Interfaces
- Configuring Inverse Multiplexing for ATM Interfaces
- Configuring Analog Modem Interfaces
- Configuring Wireless Multipoint Interfaces
- Checking the Interface Configuration
- Configuring 1-Port ADSL WAN Interface Card
- Configuring the NM-AIC-64, Contact Closure Network Module
- Configuring the 1-Port HSSI Network Module
- Configuring the Compression Network Module for the Cisco 3600 Series Routers
- Configuring the Digital Modem Network Module for the Cisco 3640 Router
- Prerequisites
- Configuration Tasks
- Configure the E1/T1 Network Module for ISDN PRI
- Configure the ISDN D-Channel Serial Interfaces
- Configure the Loopback Interface
- Configure the LAN Interface
- Create the Group Asynchronous Interface
- Configure the ISDN Dialer Interface
- Configure the Default IP Pool Information
- Configure Modem Lines for Dial-In and Dial-Out
- Configuration Example
- Configuring 1-Port G.SHDSL WAN Interface Card
- Saving Configuration Changes
- Where to Go Next
- Configuring Voice-over-IP
- Voice-over-IP Prerequisites
- Configuring the Voice Interface
- Voice-over-IP Configuration Examples
- Where to Go Next
- Configuration Examples
- Cisco 2600 Series Router Configuration Example
- Cisco 3631 Router Configuration Example
- Cisco 3725 Router Configuration Example
- 1-Port ADSL WAN Interface Card Configuration Examples
- NM-AIC-64, Contact Closure NetworkConfiguration Examples
- Cisco 3640 Central Site Configuration to Support ISDN and Modem Calls
- Formatting the Compact Flash Memory Cards
- Using the ROM Monitor
- Index
3-46
Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers
OL-1957-03
Chapter 3 Configuring with the Command-Line Interface
Configuring the 1-Port HSSI Network Module
Configuration Backup
The AIC CLI provides commands for storing and restoring configurations. Users can transfer the current
configuration of the AIC to or from the TFTP server whose address is given as a parameter to the
get config command. When a configuration file is transferred from the server to the AIC, the AIC takes
on the new configuration.
The configuration is stored as a list of commands (script) that can be applied to the CLI of an AIC for
configuration.
Two other useful commands are the get image and put config commands. Use the get image command
to get a new image, and the put config command to back up the configuration to the TFTP server.
Backup is not automatic, but the AIC reminds the user, on logout, to back up the configuration.
Override
In the case that bad software is resident on the AIC or that the configured administrator password is lost,
the AIC provides a method for recovering the card. Upon booting, the AIC begins a countdown, visible
at the AIC local CLI (Craft Port). If an ASCII character is received on that local CLI channel (DSCC4
channel 2) during this countdown, the AIC enters a mode in which a limited CLI is available. At this
limited CLI, available over the Craft Port only, no login is necessary. The user may enter commands for
software upgrade and configuration transfer. The new configuration takes effect upon a reset of the AIC
card.
After interrupting the countdown, the user will see an AIC Boot]: prompt. From this prompt, the user
can enter “?” to see the available commands, “g” to get a new application image, or “d” to delete the
current configuration and return to the defaults. (All commands require a carriage return.) In the case of
the get command, the user will be prompted for the name of the file, the IP address of the TFTP server,
and a confirmation.
Configuration Examples
The following configuration examples are shown in Appendix A, “Configuration Examples”:
• AIC IP Address Configuration Example, page A-16
• IP Route to the AIC Configuration Examples, page A-20
–
With an Unnumbered IP Address, page A-20
–
Without an Unnumbered IP Address, page A-21
Configuring the 1-Port HSSI Network Module
The Cisco 3600 series 1-port high-speed serial interface (HSSI) network module provides full-duplex
connectivity at Synchronous Optical Network (SONET) OC-1/STS-1 (51.840 Mhz), T3 (44.736 MHz),
and E3 (34.368 MHz) rates in conformance with the EIA/TIA-612 and EIA/TIA-613 specifications. The
actual rate of the interface depends on the external data service unit (DSU) and the type of service to
which it is connected. This 1-port HSSI network module can reach speeds of up to 52 Mbps in
unidirectional traffic with 1,548-byte packets and 4,250 packets per second. Asynchronous Transfer
Mode (ATM), High-Level Data Link Control (HDLC), Point-to-Point Protocol (PPP), Frame Relay, and
Switched Multi-Megabit Data Service (SMDS) WAN services are all fully supported.