User guide

ManualsBrandsCisco ManualsHardware2600 Series

Cisco Systems, Inc.

170 West Tasman Drive

San Jose, CA 95134-1706

USA

Cisco Systems, Inc.

Corporate Headquarters

Text Part Number:

Rack-Mounting the Cisco 2600 Series

Router

Product Numbers: ACS-2600RM-19=, ACS-2600RM-24=

This document describes the procedure to install Cisco 2600 series routers in a rack and includes the

following sections:

• Safety Recommendations, page 1

• FCC Class B Compliance, page 3

• Required Tools and Equipment, page 4

• Mounting the Chassis in a Rack, page 4

• What to Do after Installing the Router Hardware, page 7

• Cisco Connection Online, page 8

• Documentation CD-ROM, page 9

Safety Recommendations

Follow these guidelines to ensure general safety:

• Keep the chassis area clear and dust-free during and after installation.

• Do not wear loose clothing that could get caught in the chassis. Fasten your tie or scarf and roll

up your sleeves.

• Wear safety glasses when working under any conditions that might be hazardous to your eyes.

• Do not perform any action that creates a potential hazard to people or makes the equipment

unsafe.

78-5183-02

Summary of content (10 pages)

PAGE 1
Text Part Number: 78-5183-02 Rack-Mounting the Cisco 2600 Series Router Product Numbers: ACS-2600RM-19=, ACS-2600RM-24= This document describes the procedure to install Cisco 2600 series routers in a rack and includes the following sections: • • • • • • • Safety Recommendations, page 1 FCC Class B Compliance, page 3 Required Tools and Equipment, page 4 Mounting the Chassis in a Rack, page 4 What to Do after Installing the Router Hardware, page 7 Cisco Connection Online, page 8 Documentation CD-ROM, page
PAGE 2
Safety Recommendations Safety Warnings Safety warnings appear throughout this publication in procedures that, if performed incorrectly, may harm you. A warning symbol precedes each safety warning. Warning This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents.
PAGE 3
FCC Class B Compliance Aviso Este símbolo de aviso indica perigo. Encontra-se numa situação que lhe poderá causar danos físicos. Antes de começar a trabalhar com qualquer equipamento, familiarize-se com os perigos relacionados com circuitos eléctricos, e com quaisquer práticas comuns que possam prevenir possíveis acidentes.
PAGE 4
Required Tools and Equipment Required Tools and Equipment Installation might require some tools and equipment that are not provided as standard equipment with the router. Following are the tools and parts required for a typical router installation: • • • Flat-blade screwdrivers: small, 3/16-inch (0.476 cm) and medium, 1/4-inch (0.
PAGE 5
Attaching the Brackets Note If you are installing a Cisco 2600 series router in a 19-inch rack with a 17.5-inch opening, orient the rack-mount brackets so that, when installed, they do not increase the width of the chassis. (See Figure 2.) If you are installing a Cisco 2600 series router in a 19-inch EIA-standard rack with a 17.75-inch opening or a 23- or 24-inch rack, orient the rack-mount brackets so that, when installed, they increase the width of the chassis. (See Figure 3.
PAGE 6
Mounting the Chassis in a Rack Bracket Installation—Rear Panel Forward (19-Inch Rack with a 17.5-Inch Opening) 110V 60 Hz 1.6A MAX 27715 Figure 4 Figure 5 Bracket Installation—Rear Panel Forward (19-Inch Rack with a 17.75-Inch Opening or a 23- or 24-Inch Rack) 19-inch brackets Figure 6 27714 110V 60 Hz 1.6A MAX 23-inch and 24-inch brackets Center-Mount Bracket Installation—Rear Panel Forward 6 Rack-Mounting the Cisco 2600 Series Router 19-inch brackets 27716 110V 60 Hz 1.
PAGE 7
Installing the Router in a Rack Installing the Router in a Rack After the brackets are secured to the chassis, you can rack-mount it. Using screws that you provide, attach the chassis to the rack. (See Figure 7 and Figure 8). Mounting the Chassis in a Rack (19-Inch Rack with a 17.5-Inch Opening) 110V 60 Hz 1.6A MAX 27718 Figure 7 19-inch rack The second bracket attaches to the rack at the other side of the chassis. The brackets can also be installed with the front panel forward.
PAGE 8
Cisco Connection Online Note The Cisco IOS command reference publications provide additional software configuration information. Cisco IOS command reference publications are available on the Documentation CD-ROM that came with your router or you can order printed copies. For ordering information, see the “Documentation CD-ROM” section on page 9. Cisco Connection Online Cisco Connection Online (CCO) is Cisco Systems’ primary, real-time support channel.
PAGE 9
Documentation CD-ROM Documentation CD-ROM Cisco documentation and additional literature are available in a CD-ROM package, which ships with your product. The Documentation CD-ROM, a member of the Cisco Connection Family, is updated monthly. Therefore, it might be more current than printed documentation. To order additional copies of the Documentation CD-ROM, contact your local sales representative or call customer service. The CD-ROM package is available as a single package or as an annual subscription.
PAGE 10
Documentation CD-ROM 10 Rack-Mounting the Cisco 2600 Series Router