Specifications

x
Cisco 1751 Router Software Configuration Guide
OL-1070-01
The following output shows the voice quality statistics collected periodically:
vcsm_process_event: [1/0, 0.13, 17]
dsp_get_rx_stats: [1/0] packet_len=12 channel_id=1 packet_id=87 reset_flag=0
vcsm_process_event: [1/0, 0.13, 28]
vcsm_process_event: [1/0, 0.13, 29]
vcsm_process_event: [1/0, 0.13, 32]
vcsm_process_event: [1/0, 0.13, 17]
dsp_get_rx_stats: [1/0] packet_len=12 channel_id=1 packet_id=87 reset_flag=0
vcsm_process_event: [1/0, 0.13, 28]
vcsm_process_event: [1/0, 0.13, 29]
vcsm_process_event: [1/0, 0.13, 32]
vcsm_process_event: [1/0, 0.13, 17]
dsp_get_rx_stats: [1/0] packet_len=12 channel_id=1 packet_id=87 reset_flag=0
vcsm_process_event: [1/0, 0.13, 28]
vcsm_process_event: [1/0, 0.13, 29]
vcsm_process_event: [1/0, 0.13, 32]
The following output shows that the disconnection indication is passed to higher level code. The call
connection is torn down, and final call statistics are collected.
vcsm_process_event: [1/0, 0.13, 4] act_generate_disc
vcsm_process_event: [1/0, 0.13, 16] act_bdrop
dsp_CP_tone_off: [1/0] packet_len=10 channel_id=1 packet_id=71
vcsm_process_event: [1/0, 0.13, 18] act_disconnect
dsp_get_levels: [1/0] packet_len=10 channel_id=1 packet_id=89
vcsm_timer: 48762
vcsm_process_event: [1/0, 0.15, 34] act_get_levels
dsp_get_tx_stats: [1/0] packet_len=12 channel_id=1 packet_id=86 reset_flag=1
vcsm_process_event: [1/0, 0.15, 31] act_stats_complete
dsp_CP_tone_off: [1/0] packet_len=10 channel_id=1 packet_id=71
dsp_digit_collect_off: [1/0] packet_len=10 channel_id=129 packet_id=36
dsp_idle_mode: [1/0] packet_len=10 channel_id=1 packet_id=68
vcsm_timer: 48762
dsp_set_sig_state: [1/0] packet_len=14 channel_id=129 packet_id=39 state=0x4
timestamp=0x0
vcsm_process_event: [1/0, 0.16, 5] act_wrelease_release
dsp_CP_tone_off: [1/0] packet_len=10 channel_id=1 packet_id=71
dsp_idle_mode: [1/0] packet_len=10 channel_id=1 packet_id=68
dsp_get_rx_stats: [1/0] packet_len=12 channel_id=1 packet_id=87 reset_flag=1
debug vtsp all
Use the debug vtsp all EXEC command to show debugging information for all of the debug vtsp
commands. Use the no form of this command to disable debugging output.
[no] debug vtsp all
Usage Guidelines
The debug vtsp all command enables the following debug voice telephony service provider (vtsp)
commands: debug vtsp session, debug vtsp error, and debug vtsp dsp. For more information or
sample output, refer to the individual commands in this chapter.