user manual
Table Of Contents
- Cisco Content Services Switch Routing and Bridging Configuration Guide
- Contents
- Preface
- Configuring Interfaces and Circuits
- Interface and Circuit Overview
- Configuring Interfaces
- Configuring an Interface
- Entering a Description for the Interface
- Configuring Interface Duplex and Speed
- Setting Interface Maximum Idle Time
- Bridging an Interface to a VLAN
- Specifying VLAN Trunking for an Interface
- Configuring Spanning-Tree Bridging for a VLAN or a Trunked Interface
- Configuring Port Fast on an Interface
- Showing Interface Configurations
- Shutting Down an Interface
- Shutting Down All Interfaces
- Restarting an Interface
- Restarting All Interfaces
- Configuring Circuits
- Configuring RIP for an IP Interface
- Configuring the Switched Port Analyzer Feature
- Configuring Spanning-Tree Bridging for the CSS
- CSS Spanning-Tree Bridging Quick Start
- Configuring Spanning-Tree Bridge Aging-Time
- Configuring Spanning-Tree Bridge Forward-Time
- Configuring Spanning-Tree Bridge Hello-Time
- Configuring Spanning-Tree Bridge Max-Age
- Configuring Spanning-Tree Bridge Priority
- Disabling Bridge Spanning-Tree
- Showing Bridge Configurations
- Configuring Open Shortest Path First (OSPF)
- OSPF Overview
- CSS OSPF Configuration Quick Start
- Configuring OSPF on the CSS
- Configuring OSPF on a CSS IP Interface
- Showing OSPF Information
- OSPF Configuration in a Startup-Configuration File
- Configuring the Address Resolution Protocol
- Configuring Routing Information Protocol
- Configuring the Internet Protocol
- IP Configuration Quick Start
- Configuring an IP Route
- Disabling an Implicit Service for the Static Route Next Hop
- Configuring an IP Source Route
- Configuring the IP Record Route
- Configuring Box-to-Box Redundancy
- Configuring IP Equal-Cost Multipath
- Forwarding IP Subnet Broadcast Addressed Frames
- Configuring IP Unconditional Bridging
- Configuring IP Opportunistic Layer 3 Forwarding
- Showing IP Configuration Information
- Configuring the Cisco Discovery Protocol
- Configuring the DHCP Relay Agent
- Index
Chapter 1 Configuring Interfaces and Circuits
Configuring Interfaces
1-10
Cisco Content Services Switch Routing and Bridging Configuration Guide
OL-4580-01
• phy 1Gbits-FD-sym-asym - Sets the Gigabit Ethernet port to full-duplex
mode with symmetric and asymmetric pause frames used with the local
device.
For example, to configure Fast Ethernet interface 1 on the I/O module in slot 2 of
the CSS 11503 to 100 Mbps and half-duplex mode, enter:
(config-if[2/1])# phy 100Mbits-HD
For example, to configure gigabit interface 1 on the SCM in slot 1 of the
CSS 11503 to full-duplex mode with asymmetric pause, enter:
(config-if[1/1])# phy auto-negotiate disable
(config-if[1/1])# phy 1Gbits-FD-asym
Setting Interface Maximum Idle Time
As a troubleshooting tool to verify an interface’s ability to receive traffic, use the
max-idle command. If the interface does not receive traffic within the configured
idle time, the CSS reinitializes the interface automatically.
Set the idle time to a value greater than the interval over which the interface is
receiving traffic. For example, if the interface receives traffic every 90 seconds,
set the idle time to a value greater than 90 seconds. If you set the idle time to less
than 90 seconds, the CSS would continuously reinitialize the interface before the
interface was able to receive traffic.
Enter an idle time from 15 to 65535 seconds. The default is 0, which disables the
idle timer.
For example, to set the maximum idle time to 180 seconds for interface port 1 on
a CSS 11503, the I/O module in slot 2, enter:
(config-if[2/1])# max-idle 180
To reset the idle time for an interface to its default value of 0, enter:
(config-if[2/1])# no max-idle