user manual
Table Of Contents
- Cisco Content Services Switch Routing and Bridging Configuration Guide
- Contents
- Preface
- Configuring Interfaces and Circuits
- Interface and Circuit Overview
- Configuring Interfaces
- Configuring an Interface
- Entering a Description for the Interface
- Configuring Interface Duplex and Speed
- Setting Interface Maximum Idle Time
- Bridging an Interface to a VLAN
- Specifying VLAN Trunking for an Interface
- Configuring Spanning-Tree Bridging for a VLAN or a Trunked Interface
- Configuring Port Fast on an Interface
- Showing Interface Configurations
- Shutting Down an Interface
- Shutting Down All Interfaces
- Restarting an Interface
- Restarting All Interfaces
- Configuring Circuits
- Configuring RIP for an IP Interface
- Configuring the Switched Port Analyzer Feature
- Configuring Spanning-Tree Bridging for the CSS
- CSS Spanning-Tree Bridging Quick Start
- Configuring Spanning-Tree Bridge Aging-Time
- Configuring Spanning-Tree Bridge Forward-Time
- Configuring Spanning-Tree Bridge Hello-Time
- Configuring Spanning-Tree Bridge Max-Age
- Configuring Spanning-Tree Bridge Priority
- Disabling Bridge Spanning-Tree
- Showing Bridge Configurations
- Configuring Open Shortest Path First (OSPF)
- OSPF Overview
- CSS OSPF Configuration Quick Start
- Configuring OSPF on the CSS
- Configuring OSPF on a CSS IP Interface
- Showing OSPF Information
- OSPF Configuration in a Startup-Configuration File
- Configuring the Address Resolution Protocol
- Configuring Routing Information Protocol
- Configuring the Internet Protocol
- IP Configuration Quick Start
- Configuring an IP Route
- Disabling an Implicit Service for the Static Route Next Hop
- Configuring an IP Source Route
- Configuring the IP Record Route
- Configuring Box-to-Box Redundancy
- Configuring IP Equal-Cost Multipath
- Forwarding IP Subnet Broadcast Addressed Frames
- Configuring IP Unconditional Bridging
- Configuring IP Opportunistic Layer 3 Forwarding
- Showing IP Configuration Information
- Configuring the Cisco Discovery Protocol
- Configuring the DHCP Relay Agent
- Index
1-5
Cisco Content Services Switch Routing and Bridging Configuration Guide
OL-4580-01
Chapter 1 Configuring Interfaces and Circuits
Interface and Circuit Overview
The following running-configuration example shows the results of entering the
commands in Table 1-1.
!********************** INTERFACE *********************
interface 2/1
phy 100Mbits-FD
bridge vlan 2
!*********************** CIRCUIT **********************
circuit VLAN1
ip address 10.3.6.58 255.255.255.255
circuit VLAN3
ip address 10.3.6.60 255.255.255.255
7. (Optional) Display all circuit information for circuits that are currently
active.
(config-if[2/1])# show circuit all
8. (Optional) Display the interface configuration.
(config-if[2/1])# show interface
(config-if[2/1])# exit
9. Configure circuits as required. Assign an IP address and subnet mask to each
circuit.
(config)# circuit VLAN1
(config-circuit[VLAN1])# ip address 10.3.6.58/24
(config)# circuit VLAN3
(config-circuit[VLAN3])# ip address 10.3.6.60/24
(config-circuit-ip[VLAN3-10.3.6.60])# exit
10. (Optional) Display the circuit configuration.
(config-circuit[VLAN1])# show circuit all
11. (Recommended) Save your configuration changes to the
startup-configuration file. If you do not save the running configuration, all
configuration changes are lost upon reboot.
# copy running-config startup-config
Table 1-1 Interface and Circuit Configuration Quick Start (continued)
Task and Command Example