user manual
Table Of Contents
- Cisco Content Services Switch Routing and Bridging Configuration Guide
- Contents
- Preface
- Configuring Interfaces and Circuits
- Interface and Circuit Overview
- Configuring Interfaces
- Configuring an Interface
- Entering a Description for the Interface
- Configuring Interface Duplex and Speed
- Setting Interface Maximum Idle Time
- Bridging an Interface to a VLAN
- Specifying VLAN Trunking for an Interface
- Configuring Spanning-Tree Bridging for a VLAN or a Trunked Interface
- Configuring Port Fast on an Interface
- Showing Interface Configurations
- Shutting Down an Interface
- Shutting Down All Interfaces
- Restarting an Interface
- Restarting All Interfaces
- Configuring Circuits
- Configuring RIP for an IP Interface
- Configuring the Switched Port Analyzer Feature
- Configuring Spanning-Tree Bridging for the CSS
- CSS Spanning-Tree Bridging Quick Start
- Configuring Spanning-Tree Bridge Aging-Time
- Configuring Spanning-Tree Bridge Forward-Time
- Configuring Spanning-Tree Bridge Hello-Time
- Configuring Spanning-Tree Bridge Max-Age
- Configuring Spanning-Tree Bridge Priority
- Disabling Bridge Spanning-Tree
- Showing Bridge Configurations
- Configuring Open Shortest Path First (OSPF)
- OSPF Overview
- CSS OSPF Configuration Quick Start
- Configuring OSPF on the CSS
- Configuring OSPF on a CSS IP Interface
- Showing OSPF Information
- OSPF Configuration in a Startup-Configuration File
- Configuring the Address Resolution Protocol
- Configuring Routing Information Protocol
- Configuring the Internet Protocol
- IP Configuration Quick Start
- Configuring an IP Route
- Disabling an Implicit Service for the Static Route Next Hop
- Configuring an IP Source Route
- Configuring the IP Record Route
- Configuring Box-to-Box Redundancy
- Configuring IP Equal-Cost Multipath
- Forwarding IP Subnet Broadcast Addressed Frames
- Configuring IP Unconditional Bridging
- Configuring IP Opportunistic Layer 3 Forwarding
- Showing IP Configuration Information
- Configuring the Cisco Discovery Protocol
- Configuring the DHCP Relay Agent
- Index
Chapter 1 Configuring Interfaces and Circuits
Interface and Circuit Overview
1-4
Cisco Content Services Switch Routing and Bridging Configuration Guide
OL-4580-01
Interface and Circuit Configuration Quick Start
Table 1-1 provides a quick overview of the steps required to configure interfaces
and circuits. Each step includes the CLI command required to complete the task.
For a complete description of each feature and all the options associated with the
CLI command, see the sections following Table 1-1.
Table 1-1 Interface and Circuit Configuration Quick Start
Task and Command Example
1. Log in to the CSS.
2. Enter configuration mode by typing config.
# config
(config)#
3. Enter the interface mode for the interface you wish to configure.
This set of interface commands applies to the CSS 11501.
(config)# interface e1
(config-if[e1])#
This set of interface commands applies to the CSS 11503 or CSS 11506.
(config)# interface 2/1
(config-if[2/1])#
4. Configure the interface duplex, speed, and flow control (default is
auto-negotiate).
(config-if[2/1])# phy 100Mbits-FD
5. Bridge the interface to a VLAN. All interfaces are assigned to VLAN1 by
default.
(config-if[2/1])# bridge vlan 2
6. (Optional) Enable trunking for a CSS Gigabit Ethernet or Fast Ethernet port.
(config-if[2/1])# trunk
(config-if[2/1])# vlan 2
Create VLAN<2>, [y/n]:y
(config-if-vlan[2/1-2])# vlan 3
Create VLAN<3>, [y/n]:y
(config-if-vlan[2/1-3])#