user manual
Table Of Contents
- Cisco Content Services Switch Routing and Bridging Configuration Guide
- Contents
- Preface
- Configuring Interfaces and Circuits
- Interface and Circuit Overview
- Configuring Interfaces
- Configuring an Interface
- Entering a Description for the Interface
- Configuring Interface Duplex and Speed
- Setting Interface Maximum Idle Time
- Bridging an Interface to a VLAN
- Specifying VLAN Trunking for an Interface
- Configuring Spanning-Tree Bridging for a VLAN or a Trunked Interface
- Configuring Port Fast on an Interface
- Showing Interface Configurations
- Shutting Down an Interface
- Shutting Down All Interfaces
- Restarting an Interface
- Restarting All Interfaces
- Configuring Circuits
- Configuring RIP for an IP Interface
- Configuring the Switched Port Analyzer Feature
- Configuring Spanning-Tree Bridging for the CSS
- CSS Spanning-Tree Bridging Quick Start
- Configuring Spanning-Tree Bridge Aging-Time
- Configuring Spanning-Tree Bridge Forward-Time
- Configuring Spanning-Tree Bridge Hello-Time
- Configuring Spanning-Tree Bridge Max-Age
- Configuring Spanning-Tree Bridge Priority
- Disabling Bridge Spanning-Tree
- Showing Bridge Configurations
- Configuring Open Shortest Path First (OSPF)
- OSPF Overview
- CSS OSPF Configuration Quick Start
- Configuring OSPF on the CSS
- Configuring OSPF on a CSS IP Interface
- Showing OSPF Information
- OSPF Configuration in a Startup-Configuration File
- Configuring the Address Resolution Protocol
- Configuring Routing Information Protocol
- Configuring the Internet Protocol
- IP Configuration Quick Start
- Configuring an IP Route
- Disabling an Implicit Service for the Static Route Next Hop
- Configuring an IP Source Route
- Configuring the IP Record Route
- Configuring Box-to-Box Redundancy
- Configuring IP Equal-Cost Multipath
- Forwarding IP Subnet Broadcast Addressed Frames
- Configuring IP Unconditional Bridging
- Configuring IP Opportunistic Layer 3 Forwarding
- Showing IP Configuration Information
- Configuring the Cisco Discovery Protocol
- Configuring the DHCP Relay Agent
- Index
IN-5
Cisco Content Services Switch Routing and Bridging Configuration Guide
OL-4580-01
Index
O
opportunistic layer 3 forwarding
configuration example
6-10
configuring 6-10
OSPF
advertising other routes through OSPF
3-21
area border routers 3-5
areas 3-4
autonomous system 3-4
autonomous system boundary routers 3-5
basic network topology 3-3
configuring global parameters 3-12
configuring IP interface parameters 3-22
CSS IP interface, configuring 3-23
enabling on IP interface 3-24
interface attributes 3-24
interface configuration, assigning an
area
3-24
link-state database 3-6
overview 3-2
quick configuration verification 3-11
quick global configuration 3-7
quick IP interface configuration 3-9
router ID, configuring 3-12
routing hierarchy 3-3
startup-config file 3-43
stub area 3-5
viewing area information 3-29
viewing AS-external entries 3-36
viewing configured advertised ASE
routes
3-36, 3-37
viewing global statistics 3-29
viewing interface information 3-30
viewing link-state database information 3-33
viewing neighbors 3-39
viewing redistribution policy 3-38
viewing summary-route configuration 3-39
OSPF global
running-config example
3-8
OSPF global configuration
area, configuring
3-13
AS boundary router 3-15
disabling 3-13
enabling 3-13
equal-cost routes 3-14
removing an area 3-14
router ID 3-12
summarizing routes 3-14
OSPF interface
attributes, configuring
3-24
configuring cost 3-25
configuring CSS IP interface 3-23
dead router interval, configuring 3-25
hello packet interval, configuring 3-25
password, setting 3-26
poll interval, setting 3-26
priority, setting 3-27
retransmission interval, setting 3-27
transit delay, setting 3-28