user manual
Table Of Contents
- Cisco Content Services Switch Routing and Bridging Configuration Guide
- Contents
- Preface
- Configuring Interfaces and Circuits
- Interface and Circuit Overview
- Configuring Interfaces
- Configuring an Interface
- Entering a Description for the Interface
- Configuring Interface Duplex and Speed
- Setting Interface Maximum Idle Time
- Bridging an Interface to a VLAN
- Specifying VLAN Trunking for an Interface
- Configuring Spanning-Tree Bridging for a VLAN or a Trunked Interface
- Configuring Port Fast on an Interface
- Showing Interface Configurations
- Shutting Down an Interface
- Shutting Down All Interfaces
- Restarting an Interface
- Restarting All Interfaces
- Configuring Circuits
- Configuring RIP for an IP Interface
- Configuring the Switched Port Analyzer Feature
- Configuring Spanning-Tree Bridging for the CSS
- CSS Spanning-Tree Bridging Quick Start
- Configuring Spanning-Tree Bridge Aging-Time
- Configuring Spanning-Tree Bridge Forward-Time
- Configuring Spanning-Tree Bridge Hello-Time
- Configuring Spanning-Tree Bridge Max-Age
- Configuring Spanning-Tree Bridge Priority
- Disabling Bridge Spanning-Tree
- Showing Bridge Configurations
- Configuring Open Shortest Path First (OSPF)
- OSPF Overview
- CSS OSPF Configuration Quick Start
- Configuring OSPF on the CSS
- Configuring OSPF on a CSS IP Interface
- Showing OSPF Information
- OSPF Configuration in a Startup-Configuration File
- Configuring the Address Resolution Protocol
- Configuring Routing Information Protocol
- Configuring the Internet Protocol
- IP Configuration Quick Start
- Configuring an IP Route
- Disabling an Implicit Service for the Static Route Next Hop
- Configuring an IP Source Route
- Configuring the IP Record Route
- Configuring Box-to-Box Redundancy
- Configuring IP Equal-Cost Multipath
- Forwarding IP Subnet Broadcast Addressed Frames
- Configuring IP Unconditional Bridging
- Configuring IP Opportunistic Layer 3 Forwarding
- Showing IP Configuration Information
- Configuring the Cisco Discovery Protocol
- Configuring the DHCP Relay Agent
- Index
Index
IN-4
Cisco Content Services Switch Routing and Bridging Configuration Guide
OL-4580-01
H
hello time, configuring for bridging 2-4
I
ICMP redirect message transmission,
disabling
1-33
implicit service, disabling 6-6
interface
auto-negotiate
1-8
bridging to VLAN 1-11
configuring 1-6, 1-7
configuring Port Fast 1-16
describing 1-7
displaying statistics 1-24
duplex and speed, configuring 1-8
enabling BPDU guard 1-17
enabling Port Fast 1-17
layer, restarting 1-30
maximum idle time, configuring 1-10
overview 1-1
quick start 1-4
restarting 1-30
RIP, configuring 1-39
running-config example 1-5
showing 1-22
showing duplex and speed 1-23
showing Ethernet errors 1-27
shutting down 1-29
speed, configuring 1-8
starting 1-30
trunking to VLAN 1-11
IP
address, removing from circuit
1-32
box-to-box redundancy, configuring 6-8
configuration, showing 6-13
record route, configuring 6-7
route, configuring 6-3
route, displaying configurations 6-15
route, removing 6-5
running-config example 6-3
source route, configuring 6-7
statistics, displaying configurations 6-16
subnet broadcast, configuring 6-9
summary, displaying 6-16
unconditional bridging 6-10
IP ECMP
address, configuring
6-8
no-prefer-ingress, configuring 6-8
round-robin, configuring 6-9
IP interfaces
displaying configurations
6-14
showing 1-38
stopping RIP 1-39