user manual
Table Of Contents
- Cisco Content Services Switch Routing and Bridging Configuration Guide
- Contents
- Preface
- Configuring Interfaces and Circuits
- Interface and Circuit Overview
- Configuring Interfaces
- Configuring an Interface
- Entering a Description for the Interface
- Configuring Interface Duplex and Speed
- Setting Interface Maximum Idle Time
- Bridging an Interface to a VLAN
- Specifying VLAN Trunking for an Interface
- Configuring Spanning-Tree Bridging for a VLAN or a Trunked Interface
- Configuring Port Fast on an Interface
- Showing Interface Configurations
- Shutting Down an Interface
- Shutting Down All Interfaces
- Restarting an Interface
- Restarting All Interfaces
- Configuring Circuits
- Configuring RIP for an IP Interface
- Configuring the Switched Port Analyzer Feature
- Configuring Spanning-Tree Bridging for the CSS
- CSS Spanning-Tree Bridging Quick Start
- Configuring Spanning-Tree Bridge Aging-Time
- Configuring Spanning-Tree Bridge Forward-Time
- Configuring Spanning-Tree Bridge Hello-Time
- Configuring Spanning-Tree Bridge Max-Age
- Configuring Spanning-Tree Bridge Priority
- Disabling Bridge Spanning-Tree
- Showing Bridge Configurations
- Configuring Open Shortest Path First (OSPF)
- OSPF Overview
- CSS OSPF Configuration Quick Start
- Configuring OSPF on the CSS
- Configuring OSPF on a CSS IP Interface
- Showing OSPF Information
- OSPF Configuration in a Startup-Configuration File
- Configuring the Address Resolution Protocol
- Configuring Routing Information Protocol
- Configuring the Internet Protocol
- IP Configuration Quick Start
- Configuring an IP Route
- Disabling an Implicit Service for the Static Route Next Hop
- Configuring an IP Source Route
- Configuring the IP Record Route
- Configuring Box-to-Box Redundancy
- Configuring IP Equal-Cost Multipath
- Forwarding IP Subnet Broadcast Addressed Frames
- Configuring IP Unconditional Bridging
- Configuring IP Opportunistic Layer 3 Forwarding
- Showing IP Configuration Information
- Configuring the Cisco Discovery Protocol
- Configuring the DHCP Relay Agent
- Index
Index
IN-2
Cisco Content Services Switch Routing and Bridging Configuration Guide
OL-4580-01
circuit
configuring
1-31
configuring DHCP relay destination 8-3
displaying DHCP relay information 8-4
enabling or disabling DHCP relay agent 8-3
IP address, removing from circuit 1-32
IP interface, configuring 1-31
overview 1-1
quick start 1-4
router-discovery lifetime 1-35
router-discovery limited broadcast 1-35
router-discovery max-advertisement
interval
1-36
router-discovery min-advertisement 1-36
running-config example 1-5
showing 1-37
circuit IP
broadcast address, configuring
1-32
disabling 1-34
enabling 1-34
IP address, configuring 1-32
redirects, configuring 1-33
removing 1-32
Cisco Discovery Protocol (CDP)
configuring
7-1
displaying 7-4
running-config example 7-3
clearing
ARP parameters
4-5
CLI
conventions
xx
configuration quick start
initial CSS configuration
2-2, 4-2, 5-2, 6-2, 7-2,
8-2
interface and circuit 1-4
OSPF 3-7
configuring
bridging for CSS
2-3
CDP for CSS 7-1
circuit 1-31
circuit IP address 1-32
circuit IP interface 1-31
DHCP relay agent 8-1
ECMP 6-8
global OSPF 3-7
interface 1-6, 1-8
IP route 6-3
IP source route 6-7
IP subnet broadcast 6-9
IP unconditional bridging 6-10
OSPF global parameters 3-12
OSPF IP interface parameters 3-22
RIP for CSS 5-1
RIP for IP interface 1-39
router-discovery 1-31
Content Services Switch
11050 and 11150 port designation
1-7, 1-22
11501 port designation 1-7, 1-22