user manual
Table Of Contents
- Cisco Content Services Switch Routing and Bridging Configuration Guide
- Contents
- Preface
- Configuring Interfaces and Circuits
- Interface and Circuit Overview
- Configuring Interfaces
- Configuring an Interface
- Entering a Description for the Interface
- Configuring Interface Duplex and Speed
- Setting Interface Maximum Idle Time
- Bridging an Interface to a VLAN
- Specifying VLAN Trunking for an Interface
- Configuring Spanning-Tree Bridging for a VLAN or a Trunked Interface
- Configuring Port Fast on an Interface
- Showing Interface Configurations
- Shutting Down an Interface
- Shutting Down All Interfaces
- Restarting an Interface
- Restarting All Interfaces
- Configuring Circuits
- Configuring RIP for an IP Interface
- Configuring the Switched Port Analyzer Feature
- Configuring Spanning-Tree Bridging for the CSS
- CSS Spanning-Tree Bridging Quick Start
- Configuring Spanning-Tree Bridge Aging-Time
- Configuring Spanning-Tree Bridge Forward-Time
- Configuring Spanning-Tree Bridge Hello-Time
- Configuring Spanning-Tree Bridge Max-Age
- Configuring Spanning-Tree Bridge Priority
- Disabling Bridge Spanning-Tree
- Showing Bridge Configurations
- Configuring Open Shortest Path First (OSPF)
- OSPF Overview
- CSS OSPF Configuration Quick Start
- Configuring OSPF on the CSS
- Configuring OSPF on a CSS IP Interface
- Showing OSPF Information
- OSPF Configuration in a Startup-Configuration File
- Configuring the Address Resolution Protocol
- Configuring Routing Information Protocol
- Configuring the Internet Protocol
- IP Configuration Quick Start
- Configuring an IP Route
- Disabling an Implicit Service for the Static Route Next Hop
- Configuring an IP Source Route
- Configuring the IP Record Route
- Configuring Box-to-Box Redundancy
- Configuring IP Equal-Cost Multipath
- Forwarding IP Subnet Broadcast Addressed Frames
- Configuring IP Unconditional Bridging
- Configuring IP Opportunistic Layer 3 Forwarding
- Showing IP Configuration Information
- Configuring the Cisco Discovery Protocol
- Configuring the DHCP Relay Agent
- Index
xiii
Cisco Content Services Switch Routing and Bridging Configuration Guide
OL-4580-01
TABLES
Table 1-1 Interface and Circuit Configuration Quick Start 1-4
Table 1-2 Field Description for the show bridge port-fast Command 1-18
Table 1-3 Field Descriptions for the show bridge forwarding Command 1-20
Table 1-4 Field Descriptions for the show bridge status Command 1-20
Table 1-5 Field Descriptions for the show trunk Command 1-22
Table 1-6 Field Descriptions for the show interface Command 1-23
Table 1-7 Field Descriptions for the show phy Command 1-24
Table 1-8 Field Descriptions for the show mibii Command 1-25
Table 1-9 Field Descriptions for the show ether-errors Command 1-27
Table 1-10 Field Descriptions for the show circuits Command 1-37
Table 1-11 Field Descriptions for the show ip interfaces Command 1-38
Table 1-12 Field Descriptions for the show rip Command 1-42
Table 1-13 Field Descriptions for the show rip globals Command 1-43
Table 1-14 Field Descriptions for the show rip statistics Command 1-43
Table 1-15 Field Descriptions for the show setspan Command 1-47
Table 2-1 Spanning-Tree Bridging Configuration Quick Start 2-2
Table 2-2 Field Descriptions for the show bridge forwarding Command 2-6
Table 2-3 Field Descriptions for the show bridge status Command 2-6
Table 3-1 Global OSPF Configuration Quick Start 3-8
Table 3-2 Configuration Quick Start for OSPF on a CSS Interface 3-9
Table 3-3 Field Descriptions for the show ospf areas Command 3-29
Table 3-4 Field Descriptions for the show ospf global Command 3-29
Table 3-5 Field Descriptions for show ospf interfaces Command 3-30