Phone Adapter with Router User Guide Voice Model No. VoIPon SPA2102 www.voipon.co.uk sales@voipon.co.
VoIPon www.voipon.co.uk sales@voipon.co.
Phone Adapter with Router Copyright and Trademarks Specifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Copyright © 2006 Cisco Systems, Inc. All rights reserved. Other brands and product names are trademarks or registered trademarks of their respective holders.
Phone Adapter with Router VoIPon www.voipon.co.uk sales@voipon.co.
Phone Adapter with Router Table of Contents Chapter 1: Introduction 1 Welcome What’s in this Guide? 1 2 Chapter 2: Networking Basics 5 An Introduction to Local Area Networks The Use of IP Addresses 5 5 Chapter 3: Getting to Know the Phone Adapter 7 The Back Panel The Front Panel 7 8 Chapter 4: Getting Started 9 Before You Begin Connecting the Phone Adapter Configuring the Phone Adapter Placing the Phone Adapter 9 9 11 13 Chapter 5: Using the Interactive Voice Response Menu 15 Overview Acc
Phone Adapter with Router Appendix A: Troubleshooting 45 Common Problems and Solutions Frequently Asked Questions 45 56 Appendix B: Finding the MAC Address and IP Address for Your Ethernet Adapter Windows 98 or Me Instructions Windows 2000 or XP Instructions For the Phone Adapter’s Web-based Utility 61 62 62 Appendix C: Windows Help Appendix D: Glossary Appendix E: Specifications Appendix F: Warranty Information Appendix G: Regulatory Information Appendix H: Contact Information 63 65 69 75 77 85 In
Phone Adapter with Router List of Figures Figure 3-1: Back Panel Figure 3-2: Front Panel Figure 4-1: Connect a Telephone Figure 4-2: Connect a PC Figure 4-3: Connect to the Modem Figure 4-4: Connect Power Figure 4-5: Login Screen Figure 4-6: Router - WAN Setup Screen Figure 4-7: MAC Clone Settings Figure 4-8: Static IP Settings Figure 4-9: PPPoE Settings Figure 4-10: Measurement between Wall-Mount Slots Figure 6-1: Login Screen Figure 6-2: Router - Status Screen Figure 6-3: Router - WAN Setup Screen Figure
Phone Adapter with Router Figure 6-11: Voice - User 1 Screen Figure 6-12: Speed Dial and Supplementary Service Settings Figure 6-13: Distinctive Ring and Ring Settings Figure B-1: IP Configuration Screen Figure B-2: MAC/Adapter Address Figure B-3: MAC/Physical Address Figure B-4: MAC Address Cloning VoIPon www.voipon.co.uk sales@voipon.co.
Phone Adapter with Router Chapter 1: Introduction Welcome Thank you for choosing the Phone Adapter with Router. This Phone Adapter will allow your computers to share a high-speed Internet connection as well as resources, including files and printers. And after you have set up your Internet phone service, also known as Voice over Internet Protocol (VoIP), you will be able to make phone or fax calls using the Internet.
Phone Adapter with Router To create your network, install and set up the Phone Adapter. To guide you through the process, use the instructions in the Quick Installation or this User Guide to help you. These instructions should be all you need to get the most out of the Phone Adapter with Router. What’s in this Guide? This guide covers the basic steps for setting up a network with the Phone Adapter.
Phone Adapter with Router • Appendix A: Troubleshooting This appendix describes some possible problems and solutions, as well as frequently asked questions, regarding installation and use of the Phone Adapter. • Appendix B: Finding the MAC Address and IP Address for Your Ethernet Adapter This appendix instructs you on how to find the MAC address or Ethernet address of your PC’s Ethernet network adapter.
Phone Adapter with Router 4 Chapter 1: Introduction What’s in this Guide? VoIPon www.voipon.co.uk sales@voipon.co.
Chapter 2: Networking Basics Phone Adapter with Router An Introduction to Local Area Networks Simply put, a router is a network device that connects two networks together. The Phone Adapter connects your local area network (LAN), or the group of PCs in your home or office, to the Internet. The Phone Adapter processes and regulates the data that travels between these two networks.
Phone Adapter with Router If you use the Phone Adapter to share your cable or DSL Internet connection, contact your ISP to find out if they have assigned a static IP address to your account. If so, you will need that static IP address when configuring the Phone Adapter. You can get the information from your ISP. A dynamic IP address is automatically assigned to a device on the network. These IP addresses are called dynamic because they are only temporarily assigned to the PC or other device.
Chapter 3: Getting to Know the Phone Adapter Phone Adapter with Router The Back Panel The Phone Adapter’s ports are located on the back panel. Figure 3-1: Back Panel PHONE 1/2 Use this port to connect an analog phone (or fax machine) with an RJ-11 telephone cable. ETHERNET The ETHERNET port connects to a network device, such as a PC or a switch, with an Ethernet network cable. INTERNET The INTERNET port connects to your cable or DSL modem.
Phone Adapter with Router The Front Panel The Phone Adapter’s LEDs, which inform you about network activities, are located on the front panel. Figure 3-2: Front Panel Power Green. The Power LED lights up when the Phone Adapter is powered on and connected to the Internet. It flashes when the Phone Adapter is not connected to the Internet. The LED also flashes when the Phone Adapter is booting up or upgrading its firmware. INTERNET Green.
Phone Adapter with Router Chapter 4: Getting Started Before You Begin Make sure you have the following: • An active Internet connection • An active Internet phone service account and its settings • cable/DSL modem • One computer for configuration of the Phone Adapter • Analog telephone or fax machine with an RJ-11 phone cable Connecting the Phone Adapter 1. Power off your network devices, including your modem and PC. 2. Connect the RJ-11 phone cable to the Phone Adapter’s PHONE 1 port.
Phone Adapter with Router 4. Connect one end of an Ethernet network cable (included) to the ETHERNET port of the Phone Adapter. Connect the other end to the Ethernet port of your PC. 5. Connect one end of a different Ethernet network cable to the INTERNET port of the Phone Adapter. Connect the other end to your cable/DSL modem. 6. Power on the broadband modem. 7. Connect the included power adapter to the Phone Adapter’s power port, and then plug the power adapter into an electrical outlet.
Phone Adapter with Router Configuring the Phone Adapter 1. Launch the web browser on the PC. 2. Enter 192.168.0.1/advanced in the Address field (192.168.0.1 is the default local IP address of the Phone Adapter). Then press the Enter key. 3. If your Internet Telephony Service Provider (ITSP) did not supply a password, you will not see a login screen. Proceed to step 4. Figure 4-5: Login Screen If your ITSP supplied a password, you will see a login screen.
Phone Adapter with Router Static IP Figure 4-8: Static IP Settings a. Select Static IP from the Connection Type drop-down menu. b. In the Static IP Settings section, enter the IP address in the Static IP field, the subnet mask in the NetMask field, and the default gateway IP address in the Gateway field. c. In the Optional Settings section, enter the DNS server address(es) in the Primary DNS and optional Secondary DNS fields. d. Click the Submit All Changes button.
Phone Adapter with Router Placing the Phone Adapter There are two ways to place the Phone Adapter. The first way is to place the Phone Adapter horizontally on a surface. The second way is to mount the Phone Adapter on a wall. The wall-mount option is explained in further detail below. Wall-Mount Option The Phone Adapter has two wall-mount slots on its back panel. The distance between the two slots is 58 mm (2.28 inches). 1. Determine where you want to mount the Phone Adapter. 2.
Phone Adapter with Router 14 Chapter 4: Getting Started Placing the Phone Adapter VoIPon www.voipon.co.uk sales@voipon.co.
Phone Adapter with Router Chapter 5: Using the Interactive Voice Response Menu Overview NOTE: If your ITSP sent you the Phone Adapter, then it may be pre-configured for you, and you do not need to change any settings. Refer to the instructions supplied by your service provider for more information. You may need to manually configure the Phone Adapter by entering the settings provided by your Internet Telephony Service Provider (ITSP).
Phone Adapter with Router Using the Interactive Voice Response Menu While entering a value, such as an IP address, you may exit without entering any changes. Press the * (star) key twice within half a second. Otherwise, the * will be treated as a decimal point or dot. After entering a value, such as an IP address, press the # (pound) key to indicate you have finished your selection. To save the new setting, press 1. To review the new setting, press 2. To re-enter the new setting, press 3.
Phone Adapter with Router The settings you have saved will take effect after you have hung up the telephone. The Phone Adapter may reboot at this time. Interactive Voice Response Menu Action Command (press these keys on the telephone) Choices Description Enter Interactive Voice Response Menu **** Use this command to enter the Interactive Voice Response Menu. Do not press any other keys until you hear, “Linksys configuration menu.
Phone Adapter with Router Interactive Voice Response Menu Action Command (press these keys on the telephone) Choices Description Check Firmware Version 150 Hear the version number of the firmware currently running on the Phone Adapter. Check Primary DNS Server IP Address 160 Hear the IP address of the primary DNS (Domain Name Service) server. Check Internet Web Server Port 170 Hear the port number of the Internet Web server used for the Web-based Utility.
Phone Adapter with Router Interactive Voice Response Menu Action Command (press these keys on the telephone) Choices Description Set Network (or Subnet) Mask 121 Enter the network or subnet mask using numbers on the telephone keypad. Use the * (star) key when entering a decimal point. First, set the Internet Connection Type to static IP address; otherwise, you will hear, “Invalid Option,” if you try to set the network or subnet mask.
Phone Adapter with Router Interactive Voice Response Menu Action Command (press these keys on the telephone) Choices Description Set the Mode 201 Press 0 to select the router/NAT mode. Press 1 to select the bridge/switch mode. If the Phone Adapter acts as the router for your network, use the router/NAT mode. Press 1 to enable. Press 0 to disable. Use this setting to enable or disable WAN access to the Web-based Utility. (This Utility lets you configure the Phone Adapter.
Phone Adapter with Router Interactive Voice Response Menu Action Command (press these keys on the telephone) Choices Description User Factory Reset 877778 Press 1 to confirm. Press * (star) to cancel. The Phone Adapter will request confirmation; enter 1 to confirm. You will hear, “Option successful.” Hang up the phone. The Phone Adapter will reboot and all user-configurable settings will be reset to their factory default settings.
Phone Adapter with Router • To enter P, Q, R, S, o, q, r, or s — press 7. • To enter T, U, V, t, u, or v — press 8. • To enter W, X, Y, Z, w, x, y, or z — press 9. • To enter all other characters, press 0. NOTE: These bulleted instructions only apply when you are entering a password. At all other times, pressing a number only selects a number, not a letter or punctuation mark. For example, to enter the password phone@321 by keypad, press these keys: 746630321.
Chapter 6: Using the Web-based Utility Phone Adapter with Router Overview NOTE: If your ITSP sent you the Phone Adapter, then it may be pre-configured for you, and you do not need to change any settings. Refer to the instructions supplied by your service provider for more information. If you do wish to make changes, follow the instructions in this chapter. The Web-based Utility can be accessed via your web browser through use of a computer on your network.
Phone Adapter with Router Voice • Info. This screen displays voice-related status information about the Phone Adapter. • System. Use this screen to configure the user password. • User 1. Use this screen to configure call forward, speed dial, supplementary service, and ring settings for the primary Internet phone line. • User 2. Use this screen to configure call forward, speed dial, supplementary service, and ring settings for the secondary Internet phone line.
Phone Adapter with Router The Router Tab The Router - Status Screen This screen displays product and system information. Product Information Product Name. Shown here is the model number of the Phone Adapter. Figure 6-2: Router - Status Screen Serial Number. Shown here is the serial number of the Phone Adapter. Software Version. Shown here is the version number of the Phone Adapter software. Hardware Version. Shown here is the version number of the Phone Adapter hardware. MAC Address.
Phone Adapter with Router Current IP. Displayed here is the Internet IP address of the Phone Adapter. ip (internet protocol): a protocol used to send data over a network. Host Name. Displayed here is the host name of the Phone Adapter. ip address: the address used to identify a computer or device on a network. Domain. Displayed here is the domain name of the Phone Adapter. Current Netmask. Displayed here is the netmask or subnet mask of the Phone Adapter. Current Gateway.
Phone Adapter with Router The Router - WAN Setup Screen This screen lets you configure the Internet connection, MAC clone, remote management, QoS, VLAN, and optional settings. Information about your Internet connection type should be provided by your Internet Service Provider (ISP). If you do not have this information, contact your service provider. Internet Connection Settings Connection Type. Select the connection type you use: DHCP; Static IP; PPPOE; PPPoE, DHCP; or DHCP, PPPoE.
Phone Adapter with Router PPPoE Service Name (optional). Enter the service name provided by your ISP. Optional Settings HostName. Enter the host name, if provided by your ISP. Domain. Enter the domain name, if provided by your ISP. Primary DNS. Enter the IP address of the primary DNS server. Secondary DNS (optional). Enter the IP address of the secondary DNS server. MAC Clone Settings Enable MAC Clone Service. Select whether you want to clone a MAC address onto the Phone Adapter, yes or no.
Phone Adapter with Router Maximum Uplink Speed. Enter the maximum upload speed of your Internet connection. The default is 128Kbps. VLAN (Virtual Local Area Network) Settings Enable VLAN. VLAN (802.1Q) settings let you use the Phone Adapter in a virtual LAN environment. Select yes or no from the drop-down menu. The default is no. VLAN ID. Enter the ID number used by the Phone Adapter. The default is 1.
Phone Adapter with Router The Router - LAN Setup Screen This screen lets you configure the local network, dynamic DHCP, and static DHCP lease settings. Networking Service. Select the service you want to use, NAT or Bridge. The default is NAT. LAN Network Settings LAN IP Address. Enter the local IP address of the Phone Adapter. The default is 192.168.0.1. LAN Subnet Mask. Select the local subnet mask: 255.255.255.0, 255.255.255.128, 255.255.255.192, 255.255.255.224, 255.255.255.240, 255.255.255.
Phone Adapter with Router Host MAC Address. Enter the MAC address of the device whose IP address you want to specify. Host IP Address. Enter the IP address you want to assign to the device, 192.168.0.x (x being a different number for each device you specify). When you have finished making changes, click the Submit All Changes button to save the changes, or click the Undo All Changes button to undo your changes. 31 Chapter 6: Using the Web-based Utility The Router Tab VoIPon www.voipon.co.
Phone Adapter with Router The Router - Application Screen This screen lets you configure port forwarding, DMZ, and reserved ports range settings. Port Forwarding Settings Enable. Select yes or no for each port forwarding entry, which defines a port range to be forwarded to a server. The default is no. Service Name. Enter the name of the service or application. Starting Port. Enter the starting port number of the forwarded port range. Ending Port. Enter the ending port number of the forwarded port range.
Phone Adapter with Router Miscellaneous Settings Multicast Passthru. Multicasting allows for multiple transmissions to specific recipients at the same time. If multicasting is permitted, then the Phone Adapter will allow IP multicast packets to be forwarded to the appropriate computers. Select the types of multicast transmissions to allow: Disabled (none), Inbound Only, Outbound Only, or Inbound and Outbound. The default is Disabled. System Reserved Ports Range Starting Port.
Phone Adapter with Router The Voice Tab The Voice - Info Screen This screen shows voice-related settings for the Phone Adapter. Product Information Product Name. Shown here is the model number of the Phone Adapter. Serial Number. Shown here is the serial number of the Phone Adapter. Software Version. Shown here is the version number of the Phone Adapter software. Hardware Version. Shown here is the version number of the Phone Adapter hardware. MAC Address.
Phone Adapter with Router RTP Bytes Sent. Displayed here is the number of RTP bytes sent by the Phone Adapter. RTP Packets Recv. Displayed here is the number of RTP packets received by the Phone Adapter. RTP Bytes Recv. Displayed here is the number of RTP bytes received by the Phone Adapter. SIP Messages Sent. Displayed here is the number of SIP messages sent by the Phone Adapter. SIP Bytes Sent. Displayed here is the number of SIP bytes sent by the Phone Adapter. SIP Messages Recv.
Phone Adapter with Router Call Back Active. This indicates whether a call back request is in progress. Last Called Number. Displayed here is the last number called. Last Caller Number. Displayed here is the number of the last caller. Mapped SIP Port. Shown here is the port number of the NAT mapped SIP port. Calls 1 and 2 have the same status information available. Call 1/2 State. Displayed here is the status of the call. Call 1/2 Tone. Displayed here is the type of tone used by the call. Call 1/2 Encoder.
Phone Adapter with Router Call 1/2 Packets Sent. Displayed here is the number of packets sent. Call 1/2 Packets Recv. Displayed here is the number of packets received. Call 1/2 Bytes Sent. Displayed here is the number of bytes sent. Call 1/2 Bytes Recv. Displayed here is the number of bytes received. Call 1/2 Decode Latency. Displayed here is the number of milliseconds for decoder latency. Call 1/2 Jitter. Displayed here is the number of milliseconds for receiver jitter. Call 1/2 Round Trip Delay.
Phone Adapter with Router The Voice - System Screen This screen lets you change the password for user access to the Web-based Utility. NOTE: If your ITSP supplied this password, you may not be able to change it. Figure 6-10: Voice - System Screen System Configuration User Password. Enter the password for the user. (By default, there is no password.) When you have finished making your change, click the Submit All Changes button to save the changes, or click the Undo All Changes button to undo your change.
Phone Adapter with Router The Voice - User 1/2 Screen Use the appropriate screen to configure settings for each Internet phone line. Call Forward Settings Enter the call forwarding numbers you want to use. Cfwd All Dest. Enter the number for the Call Forward All Service feature (when you want to forward all calls). Cfwd Busy Dest. Enter the number for the Call Forward Busy feature (when the line is busy). Cfwd No Ans Dest.
Phone Adapter with Router Cfwd Sel3 Dest. Enter the forward number for the Call Forward Selective 3 feature. Cfwd Sel4 Caller. Enter the caller number pattern to trigger the Call Forward Selective 4 feature. Cfwd Sel4 Dest. Enter the forward number for the Call Forward Selective 4 feature. Cfwd Sel5 Caller. Enter the caller number pattern to trigger the Call Forward Selective 5 feature. Cfwd Sel5 Dest. Enter the forward number for the Call Forward Selective 5 feature. Cfwd Sel6 Caller.
Phone Adapter with Router Speed Dial Settings Speed Dial 2. Enter the target phone number (or URL) to assign to speed dial 2. Speed Dial 3. Enter the target phone number (or URL) to assign to speed dial 3. Figure 6-12: Speed Dial and Supplementary Service Settings Speed Dial 4. Enter the target phone number (or URL) to assign to speed dial 4. Speed Dial 5. Enter the target phone number (or URL) to assign to speed dial 5. Speed Dial 6. Enter the target phone number (or URL) to assign to speed dial 6.
Phone Adapter with Router CWCID Setting. Select whether you want to enable caller ID for call waiting, yes or no. The default is yes. Dist Ring Setting. Select whether you want to use the distinctive ring feature, yes or no. The default is yes. Message Waiting. Select whether you want to use the message waiting feature, yes or no. The default is no. Distinctive Ring Settings Ring1 Caller. Enter the caller number pattern to play Distinctive Ring/Call Waiting Tone (CWT) 1. Ring2 Caller.
Phone Adapter with Router Hold Reminder Ring. Select the ring pattern that will remind you of a call on hold when the phone is on-hook. Call Back Ring. Select the ring pattern for call back notification. Cfwd Ring Splash Len. Enter the duration of the ring splash when a call is forwarded. The range is 0 to 10.0 seconds. Cblk Ring Splash Len. Enter the duration of the ring splash when a call is blocked. The range is 0 to 10.0 seconds. VMWI Ring Splash Len.
Phone Adapter with Router 44 Chapter 6: Using the Web-based Utility The Voice Tab VoIPon www.voipon.co.uk sales@voipon.co.
Appendix A: Troubleshooting Phone Adapter with Router This appendix provides solutions to problems that may occur during the installation and operation of the Phone Adapter. Read the description below to solve your problems. If you can't find an answer here, check the website of your Internet Telephony Service Provider (ITSP) or the Linksys website at www.linksys.com. Common Problems and Solutions 1. I don’t hear a dial tone, and the PHONE LED is not lit.
Phone Adapter with Router C. Click Tools. Click Internet Options. Click the Security tab. Click the Default level button. Make sure the security level is Medium or lower. Then click the OK button. 3. I need to set a static IP address on a PC. The Phone Adapter, by default, assigns an IP address range of 192.168.0.100 to 192.168.0.150 using the DHCP server on the Phone Adapter. To set a static IP address, you can only use the ranges 192.168.0.2 to 192.168.0.99 and 192.168.0.151 to 192.168.0.254.
Phone Adapter with Router For Windows 2000: A. Click Start, Settings, and Control Panel. Double-click Network and Dial-Up Connections. B. Right-click the Local Area Connection that is associated with the Ethernet adapter you are using, and select the Properties option. C. In the Components checked are used by this connection box, highlight Internet Protocol (TCP/IP), and click the Properties button. Select Use the following IP address option. D.
Phone Adapter with Router D. In the This connection uses the following items box, highlight Internet Protocol (TCP/IP). Click the Properties button. E. Enter a unique IP address that is not used by any other computer on the network connected to the Phone Adapter. You can only use an IP address in the ranges 192.168.0.2 to 192.168.0.99 and 192.168.0.151 to 192.168.0.254. F. Enter the Subnet Mask, 255.255.255.0. G. Enter the Default Gateway, 192.168.0.1 (Phone Adapter’s default IP address). H.
Phone Adapter with Router 4. Click the OK button in the Internet Protocol (TCP/IP) Properties window, and click the OK button in the Local Area Connection Properties window. 5. Restart the computer if asked. 6. Click the OK button in the Internet Protocol (TCP/IP) Properties window, and click the OK button in the Local Area Connection Properties window. 7. Restart the computer if asked. For Windows XP: The following instructions assume you are running Windows XP with the default interface.
Phone Adapter with Router • If you do NOT get a reply, check the cable, and make sure Obtain an IP address automatically is selected in the TCP/IP settings for your Ethernet adapter. D. In the command prompt, type ping followed by your Internet IP address and press the Enter key. The Internet IP Address can be found in the web interface of the Phone Adapter. For example, if your Internet IP address is 1.2.3.4, you would enter ping 1.2.3.4 and press the Enter key.
Phone Adapter with Router E. Make sure the cable connecting from your cable or DSL modem is connected to the Phone Adapter’s Internet port. Verify that the Router - Status page of the Phone Adapter’s Web-based Utility shows a valid IP address from your ISP. F. Turn off the computer, Phone Adapter, and cable/DSL modem. Wait 30 seconds, and then turn on the Phone Adapter, cable/DSL modem, and computer. Check the Router - Status page of the Phone Adapter’s Web-based Utility to see if you get an IP address. 6.
Phone Adapter with Router D. Enter the port range of the service you are using. For example, if you have a web server, you would enter the range 80 (in the Starting Port field) to 80 (in the Ending Port field). E. Select the protocol you will be using, TCP or UDP, or select Both. F. Enter the IP address of the PC or network device that you want the port server to go to. For example, if the web server’s Ethernet adapter IP address is 192.168.0.100, you would enter 100 in the field provided.
Phone Adapter with Router information on what port services to use is to go to the website of the online game or application you want to use. Follow these steps to set up online game hosting or use a certain Internet application: A. Access the Phone Adapter’s Web-based Utility by going to http://192.168.0.1 or the IP address of the Phone Adapter. Go to the Router => Application tab. B. Select yes from the Enable drop-down menu. C. Enter any name you want to use for the service. D.
Phone Adapter with Router 9. I can’t get the Internet game, server, or application to work. If you are having difficulties getting any Internet game, server, or application to function properly, consider exposing one PC to the Internet using DeMilitarized Zone (DMZ) hosting. This option is available when an application requires too many ports or when you are not sure which port services to use.
Phone Adapter with Router For Microsoft Internet Explorer 5.0 or higher: A. B. C. D. E. Click Start, Settings, and Control Panel. Double-click Internet Options. Click the Connections tab. Click the LAN settings button and remove anything that is checked. Click the OK button to go back to the previous screen. Click the option Never dial a connection. This will remove any dial-up pop-ups for PPPoE users. For Netscape 4.7 or higher: A.
Phone Adapter with Router Frequently Asked Questions Can I make Internet phone calls if my Internet connection is down? No. When you make Internet phone calls, your high-speed Internet connection must be active. Can I make calls while I’m browsing the Internet? Yes. You can make calls while browsing the Internet. However, your web browsing may affect the quality of your Internet calls, depending on the amount of upstream data traffic passing through your Internet connection.
Phone Adapter with Router Does the Phone Adapter support any operating system other than Windows 98, Millennium, 2000, or XP? Yes, but Linksys does not, at this time, provide technical support for setup, configuration or troubleshooting of any non-Windows operating systems. Does the Phone Adapter support ICQ send file? Yes, with the following fix: click ICQ menu => preference => connections tab=>, and check I am behind a firewall or proxy.
Phone Adapter with Router the same time, even if on the same LAN (not a problem with 1.0.1.3). As far as hosting games, the HL server does not need to be in the DMZ. Just forward port 27015 to the local IP address of the server computer. How can I block corrupted FTP downloads? If you are experiencing corrupted files when you download a file with your FTP client, try using another FTP program. The web page hangs; downloads are corrupt, or nothing but junk characters are being displayed on the screen.
Phone Adapter with Router What is DMZ Hosting? Demilitarized Zone (DMZ) allows one IP address (computer) to be exposed to the Internet. Some applications require multiple TCP/IP ports to be open. It is recommended that you set your computer with a static IP if you want to use DMZ Hosting. To get the LAN IP address, see “Appendix B: Finding the MAC Address and IP Address for Your Ethernet Adapter.” If DMZ Hosting is used, does the exposed user share the public IP with the Phone Adapter? No.
Phone Adapter with Router 60 Appendix A: Troubleshooting Frequently Asked Questions VoIPon www.voipon.co.uk sales@voipon.co.
Phone Adapter with Router AppendixB:FindingtheMACAddressandIPAddressforYour Ethernet Adapter This section describes how to find the MAC address for your computer’s Ethernet adapter so you can use the MAC address cloning feature of the Phone Adapter. You can also find the IP address of your computer’s Ethernet adapter. This IP address is used for the Phone Adapter’s forwarding and/or DMZ features. Follow the steps in this appendix to find the adapter’s MAC or IP address in Windows 98, Me, 2000, or XP.
Phone Adapter with Router Windows 2000 or XP Instructions 1. Click Start and Run. In the Open field, enter cmd. Press the Enter key or click the OK button. 2. At the command prompt, enter ipconfig /all. Then press the Enter key. 3. Write down the Physical Address as shown on your computer screen; it is the MAC address for your Ethernet adapter. This appears as a series of numbers and letters. The MAC address/Physical Address is what you will use for MAC address cloning.
Phone Adapter with Router Appendix C: Windows Help Almost all Linksys products require Microsoft Windows. Windows is the most used operating system in the world and comes with many features that help make networking easier. These features can be accessed through Windows Help and are described in this appendix. TCP/IP Before a computer can communicate with a network router, TCP/IP must be enabled. TCP/IP is a set of instructions, or protocol, all PCs follow to communicate over a network.
Phone Adapter with Router 64 Appendix C: Windows Help VoIPon www.voipon.co.uk sales@voipon.co.
Phone Adapter with Router Appendix D: Glossary This glossary contains some basic networking terms you may come across when using this product. For more advanced terms, see the complete Linksys glossary at http://www.linksys.com/glossary. Bandwidth - The transmission capacity of a given device or network. Bit - A binary digit. Boot - To start a device and cause it to start executing instructions. Broadband - An always-on, fast Internet connection.
Phone Adapter with Router DNS (Domain Name Server) - The IP address of your ISP's server, which translates the names of websites into IP addresses. Domain - A specific name for a network of computers. Download - To receive a file transmitted over a network. DSL (Digital Subscriber Line) - An always-on broadband connection over traditional phone lines. Dynamic IP Address - A temporary IP address assigned by a DHCP server. Encryption - Encoding data transmitted in a network.
Phone Adapter with Router IPCONFIG - A Windows 2000 and XP utility that displays the IP address for a particular networking device. ISP (Internet Service Provider) - A company that provides access to the Internet. LAN - The computers and networking products that make up your local network. MAC (Media Access Control) Address - The unique address that a manufacturer assigns to each networking device. Mbps (MegaBits Per Second) - One million bits per second; a unit of measurement for data transmission.
Phone Adapter with Router Server - Any computer whose function in a network is to provide user access to files, printing, communications, and other services. SMTP (Simple Mail Transfer Protocol) - The standard e-mail protocol on the Internet. SNMP (Simple Network Management Protocol) - A widely used network monitoring and control protocol. Static IP Address - A fixed address assigned to a computer or device that is connected to a network. Static Routing - Forwarding data in a network via a fixed path.
Phone Adapter with Router Appendix E: Specifications Model SPA2102 Data Networking MAC Address (IEEE 802.
Phone Adapter with Router Voice Gateway Voice Algorithms Fax Capability SIPv2: Session Initiation Protocol v2 (RFC 3261, 3262, 3263, 3264) SIP Proxy Redundancy - Dynamic via DNS SRV, A Records Re-registration with Primary SIP Proxy Server SIP Support in Network Address Translation Networks - NAT (incl. STUN) Secure (Encrypted) Calling via Pre-Standard Implementation of Secure RTP Codec Name Assignment G.711 (A-law and µ-law) G.726 (16/24/32/40 kbps) G.729 A G.723.1 (6.3 kbps, 5.
Phone Adapter with Router VMWI - Visual Message Waiting Indicator via FSK Polarity Control Hook Flash Event Signaling Caller ID Generation (Name & Number) - Bellcore, DTMF, ETSI Music on Hold Client Streaming Audio Server - up to 10 sessions Security Password Protected System Reset to Factory Default Password Protected Admin and User Access Authority Provisioning/Configuration/Authentication: HTTPS with Factory Installed Client Certificate HTTP Digest - Encrypted Authentication via MD5 (RFC 1321) Up to 25
Phone Adapter with Router Subscriber Line Interface Circuit (SLIC) Ring Voltage: 40-55 VRMS Configurable Ring Frequency: 10 Hz - 40 Hz Ring Waveform: Trapezoidal and Sinusoidal Maximum Ringer Load: 3 REN On-hook/off-hook Characteristics: On-hook voltage (tip/ring): -50 V NOMINAL Off-hook current: 25 mA min Terminating Impedance: 8 Configurable Settings including North America 600 ohms, European CTR21 Regulatory Compliance FCC (Part 15 Class B), CE, ICES-003, A-Tick Certification, RoHS Power Supply Swi
Phone Adapter with Router Unit Weight 5.29 oz. (0.15 kg) Operating Temp. 32 to 113º F (0 to 45º C) Storage Temp. -13 to 185º F (-25 to 85º C) Operating Humidity 10 to 90% Non-condensing, operating and non-operating 73 Appendix E: Specifications VoIPon www.voipon.co.uk sales@voipon.co.
Phone Adapter with Router 74 Appendix E: Specifications VoIPon www.voipon.co.uk sales@voipon.co.
Phone Adapter with Router Appendix F: Warranty Information This Warranty is valid and may be processed only in the country of purchase. Contact your service provider if the warranty support issues are to be handled by them as per your service agreements. Linksys warrants to You that, for a period of two years (the “Warranty Period”), your Linksys Product will be substantially free of defects in materials and workmanship under normal use.
Phone Adapter with Router provided under this Agreement fails of its essential purpose. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to You. Please direct all inquiries to: Linksys, P.O. Box 18558, Irvine, CA 92623. 76 Appendix F: Warranty Information VoIPon www.voipon.co.uk sales@voipon.co.
Phone Adapter with Router Appendix G: Regulatory Information FCC Statement This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Phone Adapter with Router Industry Canada (Canada) This device complies with Industry Canada ICES-003 rule. Cet appareil est conforme à la norme NMB003 d'Industrie Canada. EC Declaration of Conformity (Europe) In compliance with the EMC Directive 89/336/EEC, Low Voltage Directive 73/23/EEC, and Amendment Directive 93/68/EEC, this product meets the requirements of the following standards: • EN55022 Emission • EN55024 Immunity • EN60950 Safety 78 Appendix G: Regulatory Information VoIPon www.voipon.
Phone Adapter with Router User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste Electric and Electronic Equipment (WEEE) This document contains important information for users with regards to the proper disposal and recycling of Linksys products. Consumers are required to comply with this notice for all electronic products bearing the following symbol: 79 Appendix G: Regulatory Information VoIPon www.voipon.co.uk sales@voipon.co.
Phone Adapter with Router 80 Appendix G: Regulatory Information VoIPon www.voipon.co.uk sales@voipon.co.
Phone Adapter with Router 81 Appendix G: Regulatory Information VoIPon www.voipon.co.uk sales@voipon.co.
Phone Adapter with Router 82 Appendix G: Regulatory Information VoIPon www.voipon.co.uk sales@voipon.co.
Phone Adapter with Router 83 Appendix G: Regulatory Information VoIPon www.voipon.co.uk sales@voipon.co.
Phone Adapter with Router 84 Appendix G: Regulatory Information VoIPon www.voipon.co.uk sales@voipon.co.
Phone Adapter with Router Appendix H: Contact Information Internet Telephony Service Provider (ITSP) For support, contact your ITSP. Linksys Visit Linksys online for information on the latest products and updates to your existing products at: http://www.linksys.com 85 Appendix H: Contact Information Internet Telephony Service Provider (ITSP) VoIPon www.voipon.co.uk sales@voipon.co.
Phone Adapter with Router 86 Appendix H: Contact Information Linksys VoIPon www.voipon.co.uk sales@voipon.co.
VoIPon www.voipon.co.uk sales@voipon.co.
www.linksys.com VoIPon www.voipon.co.uk sales@voipon.co.