InfiniBand Server Switches Installation Guide
Table Of Contents
- Cisco SFS 7000P and SFS 7000D InfiniBand Server Switches Hardware Installation Guide
- chapter 1
- chapter 2
- chapter 3
- chapter 4
- chapter 5
- chapter 6
- appendix A
- appendix B
- Acronyms and Abbreviations3
- Audience
- Organization
- Conventions
- Related Documentation
- Obtaining Documentation
- Documentation Feedback
- CiscoProduct Security Overview
- Product Alerts and Field Notices
- Obtaining Technical Assistance
- Obtaining Additional Publications and Information
- 1
- Introduction to Switches
- Switch Connectors
- Switch Components
- System Features
- Administrative Features
- Safety
- Site Requirements
- Power Requirements
- Site Preparation Checklist
- Safety
- Pre-installation Instructions
- Rack-Mounting the Switches
- Requirements
- Rack-Mounting the Switch
- Step1 Remove the switch, rack-mount brackets, contents of accessory kit, and documentation from ...
- Step2 Place the switch on a secure, clean surface.
- Step3 Record the MAC address and the Globally Unique Identifier (GUID) number for future reference.
- Step4 Check the slot in the rack for sufficient clearance.
- Step5 Determine the desired method of installation, and follow the appropriate steps:
- Installing the Switch with One Person
- Step1 Separate one set of the rack brackets. (See Figure3-1.)
- Step2 Attach the bracket that has the screw holes to the side of the switch, with the flange fac...
- Step3 Repeat Step1 and Step2 on the opposite side of the switch to attach the second bracket.
- Step4 Check the rack for clearance for the switch. The switch can be installed either directly o...
- Step5 Attach the remaining two rack brackets to your rack.
- Step6 Lift the switch unit, and align the sliding brackets to the switch with the brackets attac...
- Step7 Carefully push the switch unit into the rack, as shown in Figure3-5.
- Step8 Maintain at least six inches between the cooling vents and any obstructions.
- Step9 Secure the switch with your screws through the front of the rack, as shown in Figure3-6.
- Installing the Switch with Two People
- Step1 Separate the assembled rack brackets. (See Figure3-1.)
- Step2 Attach the rack bracket that has screw holes to the sides of the switch by using the screw...
- Step3 Attach the rack brackets to their counterparts before inserting the switch into the rack.
- Step4 Insert the switch into the rack with the rack bracket attached. You must tilt the switch u...
- Step5 Have one person hold the switch while another person secures the switch to the rack.
- Step6 Maintain at least six inches between the cooling vents and any obstructions.
- Step7 Attach the rack bracket to the back of the rack posts with screws that fit your rack.
- Step8 Attach the front rails to the front of the rack with screws that fit your rack. (See Figur...
- Configuring Basic Connectivity
- Obtaining an IP Address
- Obtaining an IP Address from the DHCP Server for Ethernet Management
- Obtaining a Static IP Address for Ethernet Management
- Figure3-7 Connecting the Console Cable to a Serial Console Port on the Cisco SFS7000P Server Sw...
- Figure3-8 Connecting the Console Cable to a Serial Console Port on the Cisco SFS7000D Server Sw...
- Step1 Configure the baud rate and character format of the PC terminal emulation program to match...
- Step2 Connect the supplied DB-9/RJ-45 female adapter or DB-25/RJ-45 female adapter (depending on...
- Step3 Connect one end of the supplied console cable (a flat rollover RJ-45 cable) to the serial ...
- Step1 Wait for the login prompt.
- Step2 Enter the username and password. The default username is super, and the default password i...
- Step3 Enter the enable command.
- Step4 Enter the configure command to enter the configuration mode.
- Step5 Enter the interface mgmt-ethernet command to enter the config-if-mgmt-ethernet mode.
- Step6 Enable the static address option, which turns off the default-enabled DHCP.
- Step7 Enter the IP address of the management interface, followed by the netmask, which enables t...
- Step8 Set the default gateway for the management interface. See your system administrator for a ...
- Step9 Enable the management interface by entering the no shutdown command.
- Step10 Save the configuration to preserve it between reboots.
- Connecting the 10/100 Ethernet Management Port
- Powering Up the Chassis
- Step1 Remove the power cords from the shipping package.
- Step2 Inspect the power cord to determine if it provides the proper plug and is appropriately ce...
- Step3 Connect the power cords to the power connectors on the rear of the switch.
- Step4 Connect the other end of each AC power cable into a 90-to 264-VAC power outlet operating b...
- Step5 Check the LEDs on the front of the Server Switch.
- Step6 Log in and assign a network address after you see the login prompt.
- Obtaining an IP Address
- Connecting Network Devices
- Managing the System
- Power Supply Modules
- Installing a Power Supply Module
- Step1 Ground yourself appropriately.
- Step2 Remove the filler panel from the power supply bay with a number 1 Phillips or a slotted sc...
- Step3 Remove the power supply module if one is in place by pulling on the black handle. (See Fig...
- Step4 Insert the new power supply module into the open slot until it is fully seated. You might ...
- Step5 Secure fasteners with a number 1 Phillips or a slotted screwdriver.
- Step6 Check the LEDs to verify the status of the module. (See Figure4-3 for the location of the...
- Removing Power Supply Modules
- Step1 Make sure you have a number 1 Phillips or a slotted screwdriver to disengage the fasteners.
- Step2 Ground yourself appropriately.
- Step3 Locate the power supply module that you want to remove.
- Step4 Unscrew the fasteners that hold the power supply module in place. (See Figure4-4.)
- Step5 Pull the unit from the bay.
- Step6 Install the filler panel in place of the power supply module, or install a new power suppl...
- LEDs
- Chassis Status LEDs
- Table5-1 Interpreting the Chassis Status LED
- Figure5-1 Front View of CiscoSFS7000P Server Switch Showing Chassis Status LED
- Figure5-2 Front View of Cisco SFS7000D Server Switch Showing Chassis Status LED
- Figure5-3 Rear View of CiscoSFS7000P Server Switch Showing Chassis Status LEDs
- Figure5-4 Rear View of Cisco SFS7000D Server Switch Showing Chassis Status LEDs
- InfiniBand Port LEDs
- Power Supply LEDs
- Chassis Status LEDs
- Managing the System with Element Manager
- Displaying System Information
- About Diagnostic Tests
- LED Tests
- Self-Tests
- Running Card Self-Test
- Running Chassis Self-Test
- Running Fan Self-Test
- Step1 Identify the number of the fan you want to diagnose, if you do not already know the number...
- Step2 Enter the diag fan id command.
- Step3 Display the progress of the test by entering the show diag fan command.
- Step4 Display any errors that appear in the result string by entering the show diag fru-error co...
- Step5 Reboot the chassis when the self-test is complete.
- Running Power Supply Tests
- Running a LED Test on the Power Supply
- Running a Self-Test on a Power Supply
- Step1 Determine the ID of the power supply that you want to diagnose, if you do not already know...
- Step2 Specify the type of test (self-test is chosen by default) by entering the diag power-suppl...
- Step3 Start the test.
- Step4 Display the progress of the test by entering the show diag fan command.
- Step5 Display any errors that appear in the result string by entering the show diag fru-error co...
- Step6 Reboot the chassis when the self-test is complete.
- Displaying Hardware Errors
- A
- B
- C
- D
- E
- F
- G
- H
- I
- L
- M
- N
- O
- P
- R
- S
- T
- U
- V
- W

xviii
Cisco SFS 7000P and SFS 7000D InfiniBand Server Switches Hardware Installation Guide
OL-10853-01
Preface
Obtaining Additional Publications and Information
Submitting a Service Request
Using the online TAC Service Request Tool is the fastest way to open S3 and S4 service requests. (S3 and
S4 service requests are those in which your network is minimally impaired or for which you require
product information.) After you describe your situation, the TAC Service Request Tool provides
recommended solutions. If your issue is not resolved using the recommended resources, your service
request is assigned to a Cisco engineer. The TAC Service Request Tool is located at this URL:
http://www.cisco.com/techsupport/servicerequest
For S1 or S2 service requests, or if you do not have Internet access, contact the Cisco TAC by telephone.
(S1 or S2 service requests are those in which your production network is down or severely degraded.)
Cisco engineers are assigned immediately to S1 and S2 service requests to help keep your business
operations running smoothly.
To open a service request by telephone, use one of the following numbers:
Asia-Pacific: +61 2 8446 7411
Australia: 1 800 805 227
EMEA: +32 2 704 55 55
USA: 1 800 553 2447
For a complete list of Cisco TAC contacts, go to this URL:
http://www.cisco.com/techsupport/contacts
Definitions of Service Request Severity
To ensure that all service requests are reported in a standard format, Cisco has established severity
definitions.
Severity 1 (S1)—An existing network is “down” or there is a critical impact to your business operations.
You and Cisco will commit all necessary resources around the clock to resolve the situation.
Severity 2 (S2)—Operation of an existing network is severely degraded, or significant aspects of your
business operations are negatively affected by inadequate performance of Cisco products. You and
Cisco will commit full-time resources during normal business hours to resolve the situation.
Severity 3 (S3)—Operational performance of the network is impaired while most business operations
remain functional. You and Cisco will commit resources during normal business hours to restore service
to satisfactory levels.
Severity 4 (S4)—You require information or assistance with Cisco product capabilities, installation, or
configuration. There is little or no effect on your business operations.
Obtaining Additional Publications and Information
Information about Cisco products, technologies, and network solutions is available from various online
and printed sources.
• The Cisco Online Subscription Center is the website where you can sign up for a variety of
Cisco e-mail newsletters and other communications. Create a profile and then select the
subscriptions that you would like to receive. To visit the Cisco Online Subscription Center,
go to this URL:
http://www.cisco.com/offer/subscribe