Cisco Video Surveillance IP PTZ Dome Camera User Guide Cisco 2900 Series IP Dome Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
CONTENTS Preface vii Overview vii Organization vii Obtaining Documentation and Submitting a Service Request vii CHAPTER 1 Installation 1-1 Overview 1-1 Mounting 1-1 In-Ceiling 1-2 Pendant 1-3 Wiring 1-4 Installing the Dome Drive 1-8 Installing the Lower Dome 1-9 In-Ceiling 1-10 Pendant 1-10 Switch Settings 1-11 CHAPTER 2 Operation 2-1 System Requirements 2-1 Accessing the IP Device 2-2 Live Video Page 2-2 Live Video Page Icons 2-2 PTZ Controls 2-3 Selecting a Stream 2-4 Primary Stream and Secondary St
Contents Changing the Device Name 2-8 Configuring the Time Settings 2-8 Customizing the Appearance of the Text Overlay 2-9 Generating a System Log 2-9 Rebooting the Camera 2-9 Restoring All Camera Defaults 2-9 Network Tab 2-10 Changing the Hostname 2-11 Turning On DHCP 2-11 Turning Off DHCP 2-12 Selecting the Secure Sockets Layer Mode 2-13 Generating a Certificate Request 2-13 Generating a Self-Signed Certificate 2-14 Enabling Secure Shell 2-15 Selecting SNMP Settings 2-15 Configuring SNMP V2c 2-16 Configu
Contents Selecting the Users and Groups Settings 2-38 Creating a New User 2-39 Editing a User 2-40 Deleting a User 2-40 Events Tab 2-40 Creating a System Event Source 2-41 Creating a Timer Event Source 2-41 Editing an Event Source 2-42 Deleting an Event Source 2-42 Creating an Event Handler: Send Email 2-42 Creating an Event Handler: Upload JPEG to FTP Server 2-43 Editing an Event Handler 2-44 Deleting an Event Handler 2-44 Example Handler Filter Setup 2-44 INDEX Cisco Video Surveillance IP PTZ Dome Camer
Contents Cisco Video Surveillance IP PTZ Dome Camera User Guide, Cisco 2900 Series IP Dome vi OL-24281-01
Preface Overview This document, Cisco Video Surveillance IP PTZ Dome Camera User Guide, provides information about installing, configuring, and using the Cisco Video Surveillance 2900 Series Standard Definition IP PTZ cameras.
Preface Cisco Video Surveillance IP PTZ Dome Camera User Guide, Cisco 2900 Series IP Dome viii OL-24281-01
CH A P T E R 1 Installation This chapter provides instructions for installing the Cisco 2900 Series IP Dome cameras. This chapter includes these topics: • Overview, page 1-1 • Mounting, page 1-1 • Installing the Dome Drive, page 1-8 • Installing the Lower Dome, page 1-9 • Switch Settings, page 1-11 Overview The Cisco 2900 Series IP Dome cameras are designed with ease of installation and ease of maintenance in mind.
Chapter 1 Installation Mounting In-Ceiling Step 1 Prepare the ceiling (see Figure 1-1): a. Locate the center point of the mounting location, and insert the compass tool into the ceiling. b. Place the end of a pencil in the hole on the end of the compass tool, and draw a circle. c. Cut out the circle. Figure 1-1 d. Preparing the Ceiling Attach a conduit fitting (not supplied), lock nut (not supplied), and safety chain bracket (see Figure 1-2).
Chapter 1 Installation Mounting Step 4 Pull the wiring into the back box through the conduit fitting. Step 5 Connect all required wiring (see the “Wiring” section on page 1-4). Step 6 Install the back box by compressing the spring clips and pushing the back box through the hole. Step 7 Tighten the screws until you hear a clicking noise. Pendant Step 1 Install the mount for the pendant dome. See the instructions supplied with the mount.
Chapter 1 Installation Mounting Wiring Step 1 Open the hinged door to the back box by pushing the tab lock toward the wall of the unit and lifting the door open (see Figure 1-4). Figure 1-4 Step 2 Black Box Door Remove the TXB-N from the back box circuit board (see Figure 1-5): a. Loosen the captive screw on the TXB-N. b. Carefully unplug the TXB-N from the back box circuit board.
Chapter 1 Installation Mounting Step 3 1 RJ-45 Connector 7 Standoff 2 Ethernet Cable 8 UTP Connector 3 Video Coaxial Cable 9 Back Box Circuit Board 4 16-Pin Connector 10 Audio Connectors 5 Heat Sink Standoff 11 TXB-N 6 Captive Screw Connect the auxiliary, alarm, and other wiring to the back box circuit board (see Figure 1-6). Note Aux 1: Maximum 2 A at low voltage (<40 V). Aux 2: Maximum 30 mA at 32 VDC.
Chapter 1 Installation Mounting Note To take full advantage of the distance and noise immunity benefits of audio, you must use a 600-ohm impedance matching transformer and twisted pair cable (see Figure 1-7). A stable power supply is required for optimal audio performance.
Chapter 1 Installation Mounting Warning Step 7 Step 8 An electrical short in the back box may occur if the metal BNC connector on the video coaxial cable is not completely covered by the protective boot. Perform one of the following options: • View video using both analog and IP connections—Connect the video coaxial cable from the back box circuit board to the coaxial cable coming in from the outside. Make sure that the BNC connector is completely covered by the protective boot.
Chapter 1 Installation Installing the Dome Drive Table 1-1 shows the maximum distances for video coaxial cable types.
Chapter 1 Installation Installing the Lower Dome Note When connecting more than one Cisco 2900 Series IP Dome to a single controller, terminate the unit farthest from the controller. To terminate the dome drive set the SW2-10 switch to the ON position. Figure 1-9 Step 2 Caution Setting the DIP Switches Install the dome drive. Improper installation of the dome drive can be dangerous and can seriously damage the equipment. a. Align the blue and red tabs with the blue and red labels on the back box.
Chapter 1 Installation Installing the Lower Dome In-Ceiling Step 1 Snap the clip on the end of the trim ring leash into the hole on the lip of the back box (see Figure 1-10). Figure 1-10 Step 2 Installing the In-Ceiling Lower Dome Snap the trim ring into the plastic snap washers on the mounting screws. Pendant Step 1 Attach the back box leash to the lower dome (see Figure 1-11). Figure 1-11 Step 2 Attaching the Leash to the Pendant Lower Dome Push the lower dome into the back box.
Chapter 1 Installation Switch Settings Step 3 Tighten the captive Phillips pan head screws to secure the lower dome (see Figure 1-12). Figure 1-12 Installing the Pendant Lower Dome Switch Settings Table 1-3 shows SW2 switch settings. Note If you are using Pelco D-type or Pelco P-type control, your system may not operate if the baud rate and address switches are not set correctly. The switches are set at the factory using the defaults for Pelco D-type control (2400 baud and address 1).
Chapter 1 Installation Switch Settings Table 1-3 Switch Settings for SW2 (continued) Pelco D or Pelco P Protocol Baud Rate Switch Number 1 2 3 4 5 6 7 8 2400 Baud (Default for D-type Control) OFF OFF OFF 4800 Baud (Default for P-type Control) ON 9600 Baud OFF ON OFF 6 8 9 10 9 10 OFF OFF Video Cable Type Switch Number 1 2 3 4 5 7 Coaxial Cable OFF Dome Termination Switch Number 1 2 3 4 5 6 7 8 9 10 Terminated ON Not Terminated OFF Table 1-4 shows SW1 switc
Chapter 1 Installation Switch Settings Table 1-4 Switch Settings for SW1, Pelco P-Type Control (continued) Switch Setting Address SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 17 OFF OFF OFF OFF ON 18 ON OFF OFF OFF ON 19 OFF ON OFF OFF ON 20 ON ON OFF OFF ON 21 OFF OFF ON OFF ON 22 ON OFF ON OFF ON 23 OFF ON ON OFF ON 24 ON ON ON OFF ON 25 OFF OFF OFF ON ON 26 ON OFF OFF ON ON 27 OFF ON OFF ON ON 28 ON ON OFF ON ON 29 OFF OFF ON ON ON
Chapter 1 Installation Switch Settings Table 1-5 Switch Settings for SW1, Pelco D-Type Control (continued) Switch Setting Address SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 11 ON ON OFF ON OFF OFF OFF OFF 12 OFF OFF ON ON OFF OFF OFF OFF 13 ON OFF ON ON OFF OFF OFF OFF 14 OFF ON ON ON OFF OFF OFF OFF 15 ON ON ON ON OFF OFF OFF OFF 16 OFF OFF OFF OFF ON OFF OFF OFF 17 ON OFF OFF OFF ON OFF OFF OFF 18 OFF ON OFF OFF ON OFF
Chapter 1 Installation Switch Settings Table 1-5 Switch Settings for SW1, Pelco D-Type Control (continued) Switch Setting Address SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 46 OFF ON ON ON OFF ON OFF OFF 47 ON ON ON ON OFF ON OFF OFF 48 OFF OFF OFF OFF ON ON OFF OFF 49 ON OFF OFF OFF ON ON OFF OFF 50 OFF ON OFF OFF ON ON OFF OFF 51 ON ON OFF OFF ON ON OFF OFF 52 OFF OFF ON OFF ON ON OFF OFF 53 ON OFF ON OFF ON ON OFF OF
Chapter 1 Installation Switch Settings Table 1-5 Switch Settings for SW1, Pelco D-Type Control (continued) Switch Setting Address SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 81 ON OFF OFF OFF ON OFF ON OFF 82 OFF ON OFF OFF ON OFF ON OFF 83 ON ON OFF OFF ON OFF ON OFF 84 OFF OFF ON OFF ON OFF ON OFF 85 ON OFF ON OFF ON OFF ON OFF 86 OFF ON ON OFF ON OFF ON OFF 87 ON ON ON OFF ON OFF ON OFF 88 OFF OFF OFF ON ON OFF ON OF
Chapter 1 Installation Switch Settings Table 1-5 Switch Settings for SW1, Pelco D-Type Control (continued) Switch Setting Address SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 116 OFF OFF ON OFF ON ON ON OFF 117 ON OFF ON OFF ON ON ON OFF 118 OFF ON ON OFF ON ON ON OFF 119 ON ON ON OFF ON ON ON OFF 120 OFF OFF OFF ON ON ON ON OFF 121 ON OFF OFF ON ON ON ON OFF 122 OFF ON OFF ON ON ON ON OFF 123 ON ON OFF ON ON ON ON OFF 1
Chapter 1 Installation Switch Settings Table 1-5 Switch Settings for SW1, Pelco D-Type Control (continued) Switch Setting Address SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 151 ON ON ON OFF ON OFF OFF ON 152 OFF OFF OFF ON ON OFF OFF ON 153 ON OFF OFF ON ON OFF OFF ON 154 OFF ON OFF ON ON OFF OFF ON 155 ON ON OFF ON ON OFF OFF ON 156 OFF OFF ON ON ON OFF OFF ON 157 ON OFF ON ON ON OFF OFF ON 158 OFF ON ON ON ON OFF OFF
Chapter 1 Installation Switch Settings Table 1-5 Switch Settings for SW1, Pelco D-Type Control (continued) Switch Setting Address SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 186 OFF ON OFF ON ON ON OFF ON 187 ON ON OFF ON ON ON OFF ON 188 OFF OFF ON ON ON ON OFF ON 189 ON OFF ON ON ON ON OFF ON 190 OFF ON ON ON ON ON OFF ON 191 ON ON ON ON ON ON OFF ON 192 OFF OFF OFF OFF OFF OFF ON ON 193 ON OFF OFF OFF OFF OFF ON ON 1
Chapter 1 Installation Switch Settings Table 1-5 Switch Settings for SW1, Pelco D-Type Control (continued) Switch Setting Address SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 221 ON OFF ON ON ON OFF ON ON 222 OFF ON ON ON ON OFF ON ON 223 ON ON ON ON ON OFF ON ON 224 OFF OFF OFF OFF OFF ON ON ON 225 ON OFF OFF OFF OFF ON ON ON 226 OFF ON OFF OFF OFF ON ON ON 227 ON ON OFF OFF OFF ON ON ON 228 OFF OFF ON OFF OFF ON ON ON
CH A P T E R 2 Operation This chapter describes how to operate the Cisco 2900 Series IP Dome camera. Before you begin, install the dome as described in Chapter 1, “Installation.” After installed, apply power to the system. The system will complete a configuration sequence.
Chapter 2 Operation Accessing the IP Device Accessing the IP Device The first time you access the device, the Live Video page appears. By default, you are viewing the video as a public user and only have access to the single stream live view. If, for security purposes, users should not be allowed to view video without first logging in to the camera, change the permissions for public users. To log in to the device, follow these steps: Step 1 Open the Web browser.
Chapter 2 Operation Live Video Page Table 2-1 Icon Live Video Page Icons Description Show Device List: Displays a list of viewable cameras connected to the same virtual local area network (VLAN) as the camera to which you are logged on. Disable Viewer: Closes the live view window. 1 x 1 Mode: Displays a single video pane. 2 x 2 Mode: Displays 4 video panes in rows of two. 3 x 3 Mode: Displays 9 video panes in rows of three. 4 x 4 Mode: Displays 16 video panes in rows of four.
Chapter 2 Operation Live Video Page Note If OSD is enabled, the PTZ function does not work on the camera.
Chapter 2 Operation Live Video Page • Step 4 JPEG compression—Select the image rate for the stream from the Image Rate drop-down menu. The available settings for the primary and secondary streams depend on the Image Rate setting. The QuickView Stream has only two image rate settings: 2 ips and 1 ips. Click the Select button to save the stream settings.
Chapter 2 Operation Live Video Page Multicast A multicast transmission sends data to multiple users at the same time using one transmission stream. Each multicast user that connects to the camera consumes no additional processing power; therefore, multicast video streams can be sent to an unlimited number of simultaneous users. Taking a Snapshot Step 1 Click the “Take a Snapshot” button.
Chapter 2 Operation Settings Page Step 3 Click the name of the camera you want to view. The live video of the selected camera appears in the video pane. Step 4 Repeat Step 1 through Step 3 for the remaining video panes. Settings Page Depending on user permissions, the Settings page allows you to manage camera system settings, set up users, configure events, and control the camera. Note The Settings menu might not be available if the user does not have permission to access this feature.
Chapter 2 Operation System Tab You can also use the General Settings page to turn the camera’s power LED on or off and to configure the Simple Mail Transfer Protocol (SMTP) server to send an e-mail notification when an event handler is activated. Note Consult your network administrator for information about configuring e-mail notification on your local network.
Chapter 2 Operation System Tab Step 5 Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it. Customizing the Appearance of the Text Overlay Step 1 Click the System tab. Step 2 Select General Settings from the drop-down menu. Step 3 Set the Text Overlay settings: Step 4 • Date/Time Overlay—Select Show to display the date and time in the live view overlay. The default setting is Hide.
Chapter 2 Operation Network Tab Step 1 Click the System tab. Step 2 Select General Settings from the drop-down menu. Step 3 Click the Restore All Camera Defaults button to restore the camera’s factory default settings. Note If the camera is not connected to a Dynamic Host Configuration Protocol (DHCP) network, the IP address settings for the camera will be lost and the server will not recognize the camera. DHCP On is the default setting for the camera IP address.
Chapter 2 Operation Network Tab SNMP SNMP is an application layer protocol used to manage TCP/IP-based networks from a single workstation or several workstations. The camera supports SNMP versions 2c and 3 and can be configured to send data using a trap.
Chapter 2 Operation Network Tab Step 4 Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it. If the camera is not connected to a DHCP server but DHCP is set to On, the default IP address 192.168.0.20 on subnet mask 255.255.255.0 is automatically assigned to the camera.
Chapter 2 Operation Network Tab Selecting the Secure Sockets Layer Mode Figure 2-1 SSL Configuration Page Step 1 Place your mouse pointer over the Network tab. Step 2 Select SSL from the drop-down menu. Step 3 Select one of the following modes: • Required—A signed Secure Sockets Layer (SSL) certificate must be installed, and a secure URL that begins with the protocol name “https:” must be used to access the camera. Sensitive data is always encrypted during transmission.
Chapter 2 Operation Network Tab Step 3 Click the Install Certificate button located at the bottom of the SSL Configuration page. The Select Certificate Install Method option buttons appear on the page. Step 4 Select Generate Certificate Request, and then click Next. The Certificate Request Form opens. Step 5 Fill in all of the fields, and then click Generate Request. The following progress message appears on the page: “Generating certificate signing request, please wait.
Chapter 2 Operation Network Tab Enabling Secure Shell Figure 2-2 SSH Settings Page Step 1 Place your mouse pointer over the Network tab. Step 2 Select SSH from the drop-down menu. Step 3 Select the Enabled check box. Note The username is always root and cannot be changed. The username and password are required when accessing the camera through a third-party SSH client. Step 4 Click in the Password box and type a password (4 to 16 alphanumeric characters). Passwords are case-sensitive.
Chapter 2 Operation Network Tab SNMP V2c and SNMP V3 configuration settings are independent of each other, but only one SNMP version can be active at a time. Note Configuring SNMP V2c Figure 2-3 SNMP V2c Settings Step 1 Place your mouse pointer over the Network tab. Step 2 Select V2c as the SNMP Version. Step 3 Type the community name in the Community String box. The default name for the Community String is “public.” Step 4 Step 5 Configure the Trap Configuration settings.
Chapter 2 Operation Camera Configuration Tab Configuring SNMP V3 Figure 2-4 SNMP V3 Settings Step 1 Place your mouse pointer over the Network tab. Step 2 Select V3 as the SNMP Version. Step 3 Type the SNMP user name in the SNMP user field. Step 4 Select the encryption algorithm for authentication from the Authentication drop-down menu: None, MD5, or SHA. If you use authentication method MD5 or SHA, type a password in the text box to the right of the selected Authentication encryption.
Chapter 2 Operation Camera Configuration Tab OSD All camera system menus can be accessed through the Web browser using the On-Screen Display (OSD) page. The viewed camera system menus are displayed in the preview pane of the Web browser. Use the keys on your keyboard to navigate through the camera system menus. Note If OSD is enabled, the PTZ function does not work on the camera.
Chapter 2 Operation Camera Configuration Tab • Brightness:—Controls the lighting detail in a scene. Move the slider to the right to lighten the image; move the slider to the left to darken the image. The range of adjustment is –100 to 100; the default setting is 0 (zero). • Saturation—Controls how intense or vivid the colors are in a scene. Move the slider to the right to increase the saturation level; move the slider to the left to decrease the saturation level.
Chapter 2 Operation Camera Configuration Tab Configuring a Preset Figure 2-6 Preset/Pattern Page Step 1 Place your mouse pointer over the Camera Configuration tab. Step 2 Select Presets/Patterns from the drop-down menu. Select a preset number from the Preset drop-down menu. Note Do not assign an existing preset number to a new preset or you will override the previously configured preset. Step 3 Using the control buttons, move the camera to the desired location of the live video pane.
Chapter 2 Operation Camera Configuration Tab Step 4 Click the Home button. The home preset is now configured to the location displayed in the live video pane. Selecting a Configured Preset Based on your user permissions, you can use a Web browser to call up presets 1 through 15. Configured presets can be selected from the Live View page or the Preset/Patterns page. Live View Page Select a preset number from the Preset drop-down menu.
Chapter 2 Operation Camera Configuration Tab Configuring a Pattern Figure 2-7 Preset/Pattern Page Step 1 Place your mouse pointer over the Camera Configuration tab. Step 2 Select Presets/Patterns from the drop-down menu. Step 3 Select a pattern number from the Pattern drop-down menu. Note Do not assign an existing pattern number to a new pattern or you will override the previously configured pattern. Step 4 Click Start.
Chapter 2 Operation A/V Streams Tab LiveView Page Select a pattern number from the Pattern drop-down menu. The camera runs the selected pattern. Preset/Pattern Page Step 1 Place your mouse pointer over the Camera Configuration tab. Step 2 Select a pattern number from the Pattern drop-down menu. Step 3 Click Run. The pattern is displayed in the live video pane. A/V Streams Tab Use the A/V Streams tab to configure the video and audio streams for the camera.
Chapter 2 Operation A/V Streams Tab • Image Rate and Bit Rate, page 2-26 • I-Frame Interval, page 2-35 • Quality of Service for Differentiated Services Code Point, page 2-35 • Advanced Sharpening, page 2-35 Selecting a Video Preset Configuration Figure 2-8 Select Video Preset Configuration Page Step 1 Place your mouse pointer over the A/V Streams tab. Step 2 Select the Video Preset option from the drop-down menu.
Chapter 2 Operation A/V Streams Tab Configuring a Custom Video Stream Figure 2-9 Custom Video Stream Configuration Page Step 1 Place your mouse pointer over the A/V Streams tab. Step 2 Select Video Configuration from the drop-down menu. Step 3 Click both of the Clear buttons to delete the primary and secondary streams settings. Step 4 Optional: In the Primary Stream section, type a user-friendly name in the Name box (2 to 64 characters).
Chapter 2 Operation A/V Streams Tab Compression Standards • JPEG—A commonly used video compression scheme, also known as MJPEG. JPEG has the least impact on the camera’s processor, but it requires the most bandwidth. • MPEG-4—A full-motion video standard used by most DVD recorders. MPEG-4 is less processor-intensive than JPEG, but it uses more bandwidth than H.264. • H.264—A new version of MPEG-4 compression used in high-definition video players such as Blu-ray and HD-DVD. H.
Chapter 2 Operation A/V Streams Tab Table 2-3 Supported Stream Combinations when using H.264 Compression on Primary Stream (NTSC) Secondary Stream: H.264 Secondary Stream: MJPEG Primary Stream using H.264 Encoding Resolution Frame Rate (FPS) Bit Rate (kbps) Resolution Frame Rate (FPS) Bit Rate (kbps) 4CIF 30 FPS @ 3 Mbps 3 256 4CIF 7.5 1024 1 128 6 768 5 768 3 256 2 256 1 128 15 2000 10 2000 7.
Chapter 2 Operation A/V Streams Tab Table 2-3 Supported Stream Combinations when using H.264 Compression on Primary Stream (NTSC) (continued) Secondary Stream: H.264 Secondary Stream: MJPEG Primary Stream using H.264 Encoding Resolution Frame Rate (FPS) Bit Rate (kbps) Resolution Frame Rate (FPS) Bit Rate (kbps) 4CIF 15 FPS @ 1.5 Mbps 15 1500 CIF 7.5 1024 7.5 1024 5 768 5 768 3 256 3 256 1 128 1 128 15 1500 15 2000 7.5 1024 7.
Chapter 2 Operation A/V Streams Tab Table 2-3 Supported Stream Combinations when using H.264 Compression on Primary Stream (NTSC) (continued) Secondary Stream: H.264 Secondary Stream: MJPEG Primary Stream using H.264 Encoding Resolution Frame Rate (FPS) Bit Rate (kbps) Resolution Frame Rate (FPS) Bit Rate (kbps) CIF 30 FPS @ 3 Mbps 15 1500 CIF 15 2000 10 1024 10 2000 5 768 7.
Chapter 2 Operation A/V Streams Tab Table 2-4 Supported Stream Combinations when using MJPEG Compression on Primary Stream (NTSC) Secondary Stream: H.264 Secondary Stream: MJPEG Primary Stream using MJPEG Encoding Resolution Frame Rate (FPS) Bit Rate (kbps) Resolution Frame Rate (FPS) Bit Rate (kbps) 4CIF 30 FPS @ 5.4 Mbps 15 1500 4CIF 15 2000 10 1024 10 2000 5 768 7.5 1024 3 256 6 768 1 128 5 768 3 256 2 256 1 128 15 2000 4CIF CIF 4CIF 15 FPS @ 2.
Chapter 2 Operation A/V Streams Tab Table 2-4 Supported Stream Combinations when using MJPEG Compression on Primary Stream (NTSC) (continued) Secondary Stream: H.
Chapter 2 Operation A/V Streams Tab Table 2-4 Supported Stream Combinations when using MJPEG Compression on Primary Stream (NTSC) (continued) Secondary Stream: H.
Chapter 2 Operation A/V Streams Tab Table 2-5 Supported Stream Combinations when using H.264 Compression on Primary Stream (PAL) (continued) Secondary Stream: H.264 Secondary Stream: MJPEG Primary Stream using H.264 Encoding Resolution Frame Rate (FPS) Bit Rate (kbps) Resolution Frame Rate (FPS) Bit Rate (kbps) 4CIF 5 FPS @ 1024 kbps 5 1024 4CIF 5 768 2.5 256 2.5 256 1 128 1 128 5 511 5 768 2.5 256 2.5 256 1 128 1 128 4CIF CIF CIF 4CIF 2.5 FPS @ 512 kbps 4CIF 2.
Chapter 2 Operation A/V Streams Tab Table 2-6 Supported Stream Combinations when using MJPEG Compression on Primary Stream (PAL) Secondary Stream: H.264 Secondary Stream: MJPEG Primary Stream using H.264 Encoding Resolution Frame Rate (FPS) Bit Rate (kbps) Resolution Frame Rate (FPS) Bit Rate (kbps) 4CIF 25 FPS @ 5.4 Mbps 12.5 1500 4CIF 25 2500 5 1024 12.5 1500 2.5 256 5 768 1 128 2.5 256 1 128 25 2500 4CIF CIF 4CIF 4CIF 12.5 FPS @ 2.
Chapter 2 Operation A/V Streams Tab Table 2-6 Supported Stream Combinations when using MJPEG Compression on Primary Stream (PAL) (continued) Secondary Stream: H.264 Secondary Stream: MJPEG Primary Stream using H.264 Encoding Resolution Frame Rate (FPS) Bit Rate (kbps) Resolution Frame Rate (FPS) Bit Rate (kbps) CIF 2.5 FPS @ 256 kbps CIF 2.5 256 CIF 2.
Chapter 2 Operation A/V Streams Tab To use audio with the camera you must have an audio device connected to the accessory port located on the back of the camera. After the device is connected, audio can only be enabled through the primary stream. Audio and video may not be synced when viewing and listening to the primary stream through a Web browser. You may experience a three-second delay in video when viewing the primary stream with audio.
Chapter 2 Operation Users Tab Do not use the mute button on an audio device, as it will override the audio software settings. To mute the audio device, select the Mute option located on the Audio Configuration page. Note Step 8 Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it. Users Tab Use the Users tab to create and manage user accounts and to change the way the camera manages the users settings.
Chapter 2 Operation Users Tab Selecting the Users and Groups Settings Figure 2-11 Caution General Settings Page for Users The Node and Mixed settings are advanced controls. Consult your network administrator to obtain the required information. Step 1 Place your mouse pointer over the Users tab. Step 2 Select General Settings from the drop-down menu. Step 3 Select an access level from the Public User Access Level drop-down menu.
Chapter 2 Operation Users Tab When you click the Mixed option, boxes appear for the LDAP Server and Base DN. Click in the LDAP Server and Base DN boxes, and type the necessary information in each box. Step 5 Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it. Creating a New User Figure 2-12 Users Page Step 1 Place your mouse pointer over the Users tab. Step 2 Select Users from the drop-down menu.
Chapter 2 Operation Events Tab Step 8 Click in the Last Name box and type the user’s last name (1 to 32 alphanumeric characters). Step 9 Click in the Email box and type the e-mail address of the user. Step 10 Click the Save button to save the settings and create a new user (the new user profile appears in the box on the left side of the page), or click the Reset button to clear all of the information you entered without saving it. Editing a User Step 1 Place your mouse pointer over the Users tab.
Chapter 2 Operation Events Tab Events are activated by user-defined event sources that tell the device how to react when an event occurs. Event handlers are the actions that the device takes when an event occurs. For example, a system source can be configured to send e-mail to an operator if the system shuts-down and restarts. Sources The camera supports one physical input alarm event source, a system event source, and a timer event source.
Chapter 2 Operation Events Tab Step 4 Select Timer from the Type drop-down menu. Step 5 Click in the Frequency box and type a number. Select seconds, minutes, hours, or days from the Frequency drop-down menu. Step 6 Click the Submit button to save the settings, or click the Reset button to clear all of the information you entered without saving it. Editing an Event Source Step 1 Place your mouse pointer over the Events tab. Step 2 Select Sources from the drop-down menu.
Chapter 2 Operation Events Tab Step 4 Click in the Name box and type a user-friendly name (2 to 23 alphanumeric characters). Step 5 Select Send Email from the Type drop-down menu. Step 6 Click in the text boxes (To, From, Subject, and Message), and then type the necessary information in each text box. Step 7 Select the JPEG Snapshot box if you want to send a JPEG as an attachment. Step 8 Select the Attach Raw Event Data box if you want the e-mail to include extra data about the event.
Chapter 2 Operation Events Tab Step 12 Click the Submit button to save the settings, or click the Reset button to clear all of the information you entered without saving it. See the following section for more information: • Example Handler Filter Setup, page 2-44 Editing an Event Handler Step 1 Editing an Event Handler (Task) Step 2 Place your mouse pointer over the Events tab. Step 3 Select Handlers from the drop-down menu.
Chapter 2 Operation Events Tab Step 1 Step 2 Create a handler for Monday through Saturday: a. Select the day filter fields Monday through Saturday. b. Type 0000 in the Start box and 0800 in the End box. c. Click the plus button (+) to add another time range. Type 1800 in the second Start box and type 2400 in the second End box. d. Select the source(s) that activates the handler. e. Click the Submit button to save the handler. Create a second handler for Sunday: a.
Chapter 2 Operation Events Tab Cisco Video Surveillance IP PTZ Dome Camera User Guide, Cisco 2900 Series IP Dome 2-46 OL-24281-01
A P P E N D I X A Troubleshooting Table A-1 provides information that may help you if you need to troubleshoot a Cisco 2900 Series IP Dome. Do not try to repair a unit yourself. Leave maintenance and repairs to qualified technical personnel only. Table A-1 Troubleshooting the Cisco 2900 IP Dome Issue Possible Cause Dome does not start properly after installation. The circuit board fuse may need Check the fuse on the circuit to be replaced. board inside the back box for continuity.
Appendix A Table A-1 Troubleshooting Troubleshooting the Cisco 2900 IP Dome (continued) Issue Possible Cause Suggested Resolution The audio signal is weak. You are not using the correct type of transformer. Make sure you are using a 600-ohm impedance matching transformer. The wiring distance connecting Test the equipment using a the audio equipment may be too shorter wiring distance. long. There is an echo when audio is received. The gain is not properly adjusted.
A P P E N D I X B Specifications Table B-1 lists specifications for the Cisco 2900 Series IP Dome cameras.
Appendix B Table B-1 Specifications Cisco 2900 Series IP Dome Camera Specifications (continued) Item Specification Focus Automatic with manual override Maximum Sensitivity at 35 IRE • NTSC/EIA: – 0.55 lux at 1/60 sec (color) – 0.018 lux at 1/2 sec (color) – 0.00018 lux at 1/2 sec (b/w) • PAL/CCIR: – 0.45 lux at 1/50 sec (color) – 0.015 lux at 1/1.5 sec (color) – 0.00015 lux at 1/1.
Appendix B Specifications Table B-1 Cisco 2900 Series IP Dome Camera Specifications (continued) Item Specification Fuse 1.25A Alarm inputs 2 Auxiliary outputs 7 Mechanical (dome drive only) Pan movement 360° continuous pan rotation Vertical tilt Unobstructed +2° to -92° Manual pan/tilt speeds Preset Speeds • Pan—0.1° to 80°/sec manual operation, 150°/sec turbo • Tilt—0.
Appendix B Table B-1 Specifications Cisco 2900 Series IP Dome Camera Specifications (continued) Item Specification Environmental Operating temperature • Day/night (35X zoom) pendant—Integrated/selectable: – 140°F (60°C) absolute maximum; 122°F (50°C) sustained maximum – –60°F(–51°C) Absolute minimum; prevents icing at sustained minimum of -50°F (–45°C); de-ices 0.1 inch (2.
INDEX mounting A in-ceiling A/V Streams tab pendant Audio Configuration page description 2-23 2-23 Video Presets page 2-23 2-9 restoring default values 2-23 specifications accessing, Cisco 2900 Series IP Dome 2-2 B-1 coaxial cable, distance 2-35 compression alarm event source, description audio, configuration settings 2-10 system requirements for accessing 2-39 advanced sharpening 1-3 2-8 rebooting Video Configuration page access level name 1-2 2-41 contrast 2-36 1-8 2-26
Index timer 2-41 M Events tab, description 2-40 models, Cisco 2900 Series IP Dome 1-1 mounting H in-ceiling H.
Index PTZ controls stream descriptions viewing multicast 2-3 2-6 primary and secondary combinations supported 2-2 QuickView 2-5 secondary Q 2-5 selecting Quality of Service (QoS) QuickView stream unicast 2-35 2-4 2-5 stream, primary 2-5 2-26 2-5 SW1, switch settings R rebooting, Cisco 2900 Series IP Dome Pelco D-Type 1-13 Pelco P-Type 1-12 SW2, switch settings 2-9 1-11 switch settings SW1 S saturation 2-19 secondary stream system log 2-7 description 2-35 2-41 2-9 Sys
Index U unicast stream 2-5 Upload JPEG to FTP Server handler creating 2-43 description 2-41 user access level 2-39 creating 2-39 deleting 2-40 editing 2-40 management mode settings 2-38 2-38 user group management mode settings 2-38 2-38 Users tab description 2-37 General Settings page Users page 2-37 2-37 V video advanced sharpening bit rate 2-35 2-26 compression 2-26 custom stream configuration I-frame interval image rate 2-35 2-26 multiscreen view 2-6 preset configurati
