Regulatory Compliance and Safety Information for Cisco SB 100 Series Routers This document provides international regulatory and safety compliance information for all Cisco SB 100 series routers. Use this document with the other publications for the Cisco SB 100 series router you have purchased.
Translated Safety Warnings Translated Safety Warnings This section includes translations in multiple languages of the warnings that may appear in your product documents. The following statements are warnings or safety guidelines. A warning means danger. You are in a situation that could cause bodily injury. Before working on equipment, be aware of the hazards involved with electrical circuitry and standard safety practices to prevent accidents.
Translated Safety Warnings Attention La connexion du réseau numérique intégré (Integrated Services Digital Network ou ISDN) constitue une source de tension qui ne doit pas être accessible à l'utilisateur. Les utilisateurs ne doivent jamais tenter de modifier ni même d'ouvrir un matériel fourni par une compagnie de téléphone public, ou le matériel de connexion.
Translated Safety Warnings Statement 39—Grounded Equipment Warning Warning Waarschuwing This equipment is intended to be grounded. Ensure that the host is connected to earth ground during normal use. Deze apparatuur hoort geaard te worden Zorg dat de host-computer tijdens normaal gebruik met aarde is verbonden. Varoitus Tämä laitteisto on tarkoitettu maadoitettavaksi. Varmista, että isäntälaite on yhdistetty maahan normaalikäytön aikana. Attention Cet équipement doit être relié à la terre.
Translated Safety Warnings Statement 43—Jewelry Removal Warning Warning Before working on equipment that is connected to power lines, remove jewelry (including rings, necklaces, and watches). Metal objects will heat up when connected to power and ground and can cause serious burns or weld the metal object to the terminals. Waarschuwing Alvorens aan apparatuur te werken die met elektrische leidingen is verbonden, sieraden (inclusief ringen, kettingen en horloges) verwijderen.
Translated Safety Warnings Aviso Antes de trabalhar em equipamento que esteja ligado a linhas de corrente, retire todas as jóias que estiver a usar (incluindo anéis, fios e relógios). Os objectos metálicos aquecerão em contacto com a corrente e em contacto com a ligação à terra, podendo causar queimaduras graves ou ficarem soldados aos terminais. ¡Advertencia! Antes de operar sobre equipos conectados a líneas de alimentación, quitarse las joyas (incluidos anillos, collares y relojes).
Translated Safety Warnings Attention Lors de cette procédure, toujours porter des bracelets antistatiques pour éviter que des décharges électriques n’endommagent la carte. Pour éviter l’électrocution, ne pas toucher le fond de panier directement avec la main ni avec un outil métallique. Warnung Zur Vermeidung einer Beschädigung der Karte durch elektrostatische Entladung während dieses Verfahrens ein Erdungsband am Handgelenk tragen.
Translated Safety Warnings Statement 150—Power Off Before Working on System Warning Waarschuwing Varoitus Before working on a system that has a standby/off switch, turn off the power by pressing the power switch to standby and unplug the power cord. Alvorens aan een systeem met een standby/uit-schakelaar te werken dient u de voeding uit te schakelen door de voedingsschakelaar op standby te zetten en het voedingssnoer te verwijderen.
Translated Safety Warnings Statement 151—ISDN Network Voltages Warning Warning Network hazardous voltages are present in the ISDN cable. If you detach the ISDN cable, detach the end away from the router first to avoid possible electric shock. Network hazardous voltages also are present on the system card in the area of the ISDN port (RJ-45 connector), regardless of when power is turned off (by pressing power switch to standby).
Translated Safety Warnings ¡Advertencia! Las líneas RSDI contienen voltajes peligrosos de la red. Si desconecta el cable RSDI, separe primero el final del router para evitar posibles choques eléctricos. La tarjeta del sistema en el área del puerto RSDI (conector RJ-45) también contiene altos voltajes de la red, independientemente de si está apagada (posicionando el interruptor de la corriente a standby). Varning! I ISDN-kabeln förekommer spänningar som är farliga för nätverk.
Translated Safety Warnings Statement 1004—Installation Instructions Warning Waarschuwing Varoitus Read the installation instructions before connecting the system to the power source. Raadpleeg de installatie-instructies voordat u het systeem op de voedingsbron aansluit. Lue asennusohjeet ennen järjestelmän yhdistämistä virtalähteeseen. Attention Avant de brancher le système sur la source d'alimentation, consulter les directives d'installation.
Translated Safety Warnings Statement 1005—Circuit Breaker Warning Waarschuwing Varoitus This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 120 VAC, 15A U.S. (240 VAC, 10A international) Dit produkt is afhankelijk van de installatie van het gebouw voor kortsluit- (overstroom) beveiliging. Controleer of er een zekering of stroomverbreker van niet meer dan 120 Volt wisselstroom, 15 A voor de V.S.
Translated Safety Warnings Statement 1021—SELV Circuit Warning Waarschuwing Varoitus To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-network voltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits. Some LAN and WAN ports both use RJ-45 connectors. Use caution when connecting cables.
Translated Safety Warnings Attention Pour éviter une électrocution, ne raccordez pas les circuits de sécurité basse tension (Safety Extra-Low Voltage ou SELV) à des circuits de tension de réseau téléphonique (Telephone Network Voltage ou TNV). Les ports du réseau local (LAN) contiennent des circuits SELV et les ports du réseau longue distance (WAN) sont munis de circuits TNV. Certains ports LAN et WAN utilisent des connecteurs RJ-45. Raccordez les câbles en prenant toutes les précautions nécessaires.
Translated Safety Warnings Statement 1023—No. 26 AWG Warning Waarschuwing Varoitus To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord. Statement 1023 Om brandgevaar te reduceren, dient slechts telecommunicatielijnsnoer nr. 26 AWG of groter gebruikt te worden. Tulipalovaaran vähentämiseksi käytä ainoastaan nro 26 AWG- tai paksumpaa tietoliikennejohdinta.
Translated Safety Warnings Statement 1030—Equipment Installation Warning Waarschuwing Varoitus Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030 Deze apparatuur mag alleen worden geïnstalleerd, vervangen of hersteld door bevoegd geschoold personeel. Tämän laitteen saa asentaa, vaihtaa tai huoltaa ainoastaan koulutettu ja laitteen tunteva henkilökunta.
Translated Safety Warnings Aviso Advarsel Warning Waarschuwing Varoitus Somente uma equipe treinada e qualificada tem permissão para instalar, substituir ou dar manutenção a este equipamento. Kun uddannede personer må installere, udskifte komponenter i eller servicere dette udstyr. Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Deze apparatuur mag alleen worden geïnstalleerd, vervangen of hersteld door bevoegd geschoold personeel.
Translated Safety Warnings Attention Il est vivement recommandé de confier l'installation, le remplacement et la maintenance de ces équipements à des personnels qualifiés et expérimentés. Warnung Das Installieren, Ersetzen oder Bedienen dieser Ausrüstung sollte nur geschultem, qualifiziertem Personal gestattet werden. Avvertenza Questo apparato può essere installato, sostituito o mantenuto unicamente da un personale competente.
Translated Safety Warnings Aviso Advarsel O descarte definitivo deste produto deve estar de acordo com todas as leis e regulamentações nacionais. Endelig bortskaffelse af dette produkt skal ske i henhold til gældende love og regler.
Agency Approvals Agency Approvals Table 1 lists the safety and electromagnetic interference (EMI) standards that apply to the Cisco SB 100 series routers.
Cisco SB 100 seriesFCC Class B Statement • Cisco SB 100 series Note Warning TIA/EIA/IS-968, Technical Criteria for Terminal Equipment to Prevent Harm to the Telephone Network, July 2001, as adopted by the Administrative Council on Terminal Attachments (ACTA). FCC Class B Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Operating Conditions for the European Community Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions may give the telecommunications company cause to request the user to disconnect the equipment.
Conformité Européenne (CE) Marking Directive Conformité Européenne (CE) Marking Directive This product bears the CE mark in conformance with Annex VII of Directive 1999/5/CE. European Union Statements The following statements apply to routers used in the European Union (EU). Network Termination Point Statement This product does not contain a “Network Termination Point” (NTP) as defined by ETSI 300 386-2. This product is classified by the manufacturer as “Terminal Equipment.
Australia Compliance Statement Australia Compliance Statement Network connected equipment is approved to the Australian and New Zealand Safety and EMC requirements by Cisco Systems Incorporated which is a Recognized Laboratory by ACA and New Zealand. Stand-alone power supply modules provided with this equipment are separately approved by an Australian State designated Electricity Authority.
Documentation Feedback You can order Cisco documentation in these ways: • Registered Cisco.com users (Cisco direct customers) can order Cisco product documentation from the Ordering tool: http://www.cisco.com/en/US/partner/ordering/index.shtml • Nonregistered Cisco.com users can order documentation through a local account representative by calling Cisco Systems Corporate Headquarters (California, USA) at 408 526-7208 or, elsewhere in North America, by calling 1 800 553-NETS (6387).
Obtaining Technical Assistance or model name; by tree view; or for certain products, by copying and pasting show command output. Search results show an illustration of your product with the serial number label location highlighted. Locate the serial number label on your product and record the information before placing a service call. Submitting a Service Request Using the online TAC Service Request Tool is the fastest way to open S3 and S4 service requests.
Obtaining Additional Publications and Information Obtaining Additional Publications and Information Information about Cisco products, technologies, and network solutions is available from various online and printed sources. • Cisco Marketplace provides a variety of Cisco books, reference guides, and logo merchandise. Visit Cisco Marketplace, the company store, at this URL: http://www.cisco.
Obtaining Additional Publications and Information Regulatory Compliance and Safety Information for Cisco SB 100 series Routers Copyright © 2005, Cisco Systems, Inc. All rights reserved. Printed in the USA on recycled paper containing 10% postconsumer waste.
