Cisco 800 Series Routers Hardware Installation Guide Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
CCSP, CCVP, the Cisco Square Bridge logo, Follow Me Browsing, and StackWise are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, and iQuick Study are service marks of Cisco Systems, Inc.
CONTENTS About This Guide Audience vii vii Organization vii Conventions vii Obtaining Documentation ix Cisco.
Contents Installing Your Router 2-5 Connecting Ethernet Devices 2-6 Connecting an ISDN Line 2-10 Connecting an IDSL Line 2-13 Connecting a Digital Telephone 2-14 Connecting an Analog Telephone, Fax, or Modem Connecting a Terminal or PC 2-17 Connecting the Power Supply 2-18 2-15 Mounting Your Router 2-18 Mounting on a Table 2-18 Mounting on a Wall 2-19 Verifying Installation 2-20 Where to Go from Here CHAPTER Troubleshooting 3 2-22 3-1 Problems During First Startup Problems After First Startup 3-
About This Guide This preface discusses the audience, organization, and conventions used in this guide. Audience This guide is intended for service technicians with all levels of experience in installing routers. The goal of all technicians is to connect the router to the network as quickly as possible. Where relevant, this guide explains how the router is implemented and why.
About This Guide Conventions Caution This symbol means reader be careful. In this situation, you might do something that could result in equipment damage or loss of data. Warning This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with the standard practices for preventing accidents. Waarschuwing Dit waarschuwingssymbool betekent gevaar.
About This Guide Obtaining Documentation ¡Atención! Varning! Este símbolo de aviso significa peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considerar los riesgos que entraña la corriente eléctrica y familiarizarse con los procedimientos estándar de prevención de accidentes. Denna varningssymbol signalerar fara. Du befinner dig i en situation som kan leda till personskada.
About This Guide Documentation Feedback You can order Cisco documentation in these ways: • Registered Cisco.com users (Cisco direct customers) can order Cisco product documentation from the Ordering tool: http://www.cisco.com/en/US/partner/ordering/ • Nonregistered Cisco.com users can order documentation through a local account representative by calling Cisco Systems Corporate Headquarters (California, USA) at 408 526-7208 or, elsewhere in North America, by calling 1 800 553-NETS (6387).
About This Guide Obtaining Technical Assistance Tip We encourage you to use Pretty Good Privacy (PGP) or a compatible product to encrypt any sensitive information that you send to Cisco. PSIRT can work from encrypted information that is compatible with PGP versions 2.x through 8.x. Never use a revoked or an expired encryption key. The correct public key to use in your correspondence with PSIRT is the one that has the most recent creation date in this public key server list: http://pgp.mit.
About This Guide Obtaining Additional Publications and Information Submitting a Service Request Using the online TAC Service Request Tool is the fastest way to open S3 and S4 service requests. (S3 and S4 service requests are those in which your network is minimally impaired or for which you require product information.) After you describe your situation, the TAC Service Request Tool provides recommended solutions.
About This Guide Obtaining Additional Publications and Information • Cisco Press publishes a wide range of general networking, training and certification titles. Both new and experienced users will benefit from these publications. For current Cisco Press titles and other information, go to Cisco Press at this URL: http://www.ciscopress.com • Packet magazine is the Cisco Systems technical user magazine for maximizing Internet and networking investments.
About This Guide Obtaining Additional Publications and Information Cisco 800 Series Routers Hardware Installation Guide xiv 78-5373-04
C H A P T E R 1 Overview The Cisco 800 series routers connect small professional offices or telecommuters over Integrated Services Digital Network (ISDN) Basic Rate Interface (BRI) lines to the Corporate LANs and the Internet. The routers offer bridging and multiprotocol routing capability between LAN and WAN ports.
Chapter 1 Overview Feature Summary Feature Summary Table 1-1 summarizes the features of the Cisco 800 series routers. Table 1-1 Cisco 800 Series Feature Summary Feature Routers Description 10BASE-T Ethernet port(s) All Provides connection to 10BASE-T (10 Mbps) Ethernet networks. Compatible with 10/100-Mbps devices. ISDN BRI S/T port Cisco 801 and 803 Provides connection to ISDN S/T network. ISDN BRI U port Cisco 802 and 804 Provides connection to ISDN U network.
Chapter 1 Overview Router Ports Summary Router Ports Summary Table 1-2 lists the Cisco 800 series routers and ports. Table 1-2 Router Ports Router Ethernet Ports ISDN Ports Telephone Ports Cisco 801 One ISDN BRI S/T None Cisco 802 One ISDN BRI U None Cisco 802 IDSL One IDSL None Cisco 803 Four ISDN BRI S/T Two Cisco 804 Four ISDN BRI U Two Cisco 804 IDSL Four IDSL None Front Panels The figures in this section show the front panel of the Cisco 800 series routers.
Chapter 1 Overview Back Panels Figure 1-3 Cisco 804 IDSL Front Panel ETHERNE 30770 IDSL T IDSL Back Panels The figures in this section show the back panel of each of the Cisco 800 series routers. If the symbol of suitability ( ) appears above a port, you can connect the port directly to a public network that follows the European Union standards. Warning Cisco 801 Router Back Panel Link LED Indicates state of Ethernet port. On when connected. Ethernet port Connect Ethernet network device.
Chapter 1 Overview Back Panels Cisco 802 Router Back Panel Ethernet port Connect Ethernet network device. Link LED Indicates state of Ethernet port. HU LINK NOB HUB ETHERN Figure 1-6 Power switch l = On. = Standby or no power output. Cisco 80 ET 2 CONSOL E 10 BASE ISDN U T HUB/NO HUB button (for Ethernet port) Determines cable type for Ethernet device connection. 11667 Cable lock Use cable lock to physically secure router. ISDN BRI U port Connect to ISDN wall jack.
Chapter 1 Overview Back Panels Figure 1-7 Cisco 804 Router Back Panel HUB NO HU ETHERN Power switch l = On. = Standby or no power output. Cisco 80 ET 10 BA B Telephone ports Connect to telephone, fax machine, or modem. ISDN BRI U port Connect to ISDN wall jack. Ethernet ports Connect Ethernet network devices. 4 SE T CONSOL E ISDN U Cable lock Use cable lock to physically secure router. 3 1 HUB/NO HUB button (for Ethernet port 0) Determines cable type for Ethernet device connection.
Chapter 1 Overview LEDs Figure 1-9 Cisco 804 IDSL Router Back Panel TO HUB TO PC ETHERN Power switch l = On. = Standby or no power output. IDSL port Connect to IDSL wall jack. Ethernet ports Connect Ethernet network devices. Cisco 80 ET 10 BA SE T 4 IDSL CONSOL E IDSL Cable lock Use cable lock to physically secure router. 2 3 TO HUB/TO PC (for Ethernet port 1) Determines cable type for Ethernet device connection. 4 30772 1 Console port Connect PC or terminal.
Chapter 1 Overview LEDs Table 1-3 LED Functions (continued) LED Color Function CH1 Orange Blinks when placing or receiving a call on the first ISDN B channel. On when a call is connected on the first ISDN B channel. For IDSL routers, see the Note following this table. CH1 RXD Orange Blinks when packets are received from the first ISDN B channel. CH1 TXD Orange Blinks when packets are sent from the first ISDN B channel.
C H A P T E R 2 Installation This chapter provides information on the following topics: • Safety • European Union Statements • Preventing Electrostatic Discharge Damage • Preventing Router Damage • Unpacking Your Router • Preinstallation Activities • Installing Your Router • Mounting Your Router • Verifying Installation • Where to Go from Here Cisco 800 Series Routers Hardware Installation Guide 78-5373-04 2-1
Chapter 2 Installation Safety Safety Before installing the router, read the following warnings: Warning Only trained and qualified personnel should be allowed to install or replace this equipment. Warning Read the installation instructions before you connect the system to its power source. Warning Before working on a system that has a standby/off switch, turn the power to standby and unplug the power cord.
Chapter 2 Installation Preventing Electrostatic Discharge Damage Network Termination Point Statement This product does not contain a “Network Termination Point” (NTP) as defined by ETSI 300 386-2. This product is classified by the manufacturer as “Terminal Equipment.” If you have any additional questions, please contact your local network operator.
Chapter 2 Installation Preventing Router Damage Preventing Router Damage Use the following guidelines when connecting devices to your router: Warning • Connect the color-coded cables supplied by Cisco Systems to the color-coded ports on the back panel. • If you must supply your own cable, see the “Cabling Specifications” section in Appendix B, “Specifications and Cables.
Chapter 2 Installation Installing Your Router • If you are outside of North America, ask your telephone service provider if you must provide an external Network Termination 1 (NT1) and the ISDN U cable that connects the NT1 to the ISDN wall jack. Ask for NT1 vendors if necessary. • If you are in North America, ask your telephone service provider for external NT1 vendors. Provide the ISDN U cable that connects the NT1 to the ISDN wall jack.
Chapter 2 Installation Installing Your Router Connecting Ethernet Devices Table 2-2 lists the Ethernet devices you can connect to the router, connections for each device, and the settings of the router HUB/NO HUB or TO HUB/TO PC button (the default setting is IN).
Chapter 2 Installation Installing Your Router Table 2-2 Connecting Ethernet Devices (continued) Network Device Connected to Router Router Port Ethernet Cable Type1 Router HUB/NO HUB, TO HUB/TO PC Button Setting Network Device Button Setting2 Server, PC, or workstation Cisco 801 and 802 routers: Ethernet port Cisco 803 and 804 routers: Ethernet port Ø Straight-through OUT N/A Server, PC, or workstation Cisco 802 IDSL router: Ethernet port Cisco 804 IDSL router: Ethernet port 1 Straight-throug
Chapter 2 Installation Installing Your Router Connecting Hubs If you have a Cisco 803, 804, or 804 IDSL router, you can connect as many as four hubs. Before connecting a hub, see Table 2-2, and do the following: • Choose Ethernet cables. • On the router, set the HUB/NO HUB or TO HUB/TO PC button. • On the hub, set the HUB/NO HUB button or its equivalent. Follow the steps in Figure 2-1 to connect a hub to a Cisco 800 series ISDN or IDSL router.
Chapter 2 Installation Installing Your Router Connecting a Server, PC, or Workstation Before connecting the server, PC, or workstation, refer to Table 2-2 to determine how to set the router HUB/NO HUB or TO HUB/TO PC button. Ensure that your device has a 10- or 10/100-Mbps NIC. To connect one of these devices to a Cisco 800 series ISDN or IDSL router, follow the steps in Figure 2-2. Caution Figure 2-2 Always connect the yellow cable or an Ethernet cable to the yellow ports on the router.
Chapter 2 Installation Installing Your Router Connecting an ISDN Line The procedure to connect an ISDN line depends on the router and in some cases your location.
Chapter 2 Installation Installing Your Router Figure 2-3 Connecting an ISDN Line to Cisco 801 and Cisco 803 Routers (without External NT1) Cisco 803 router ETHER NET 10 B Cisco 80 3 BASE T CONSOL E 0 1 ISDN S/T 11677 HUB NO HU PHONE 2 3 1 2 1. Connect orange cable to orange ISDN S/T port. ISDN wall jack 2. Connect other end of cable to ISDN wall jack.
Chapter 2 Installation Installing Your Router Connecting an ISDN Line to Cisco 802 and Cisco 804 Routers To connect an ISDN line to Cisco 802 and Cisco 804 routers, follow the steps in Figure 2-5. Warning Network hazardous voltages are present in the ISDN cable. If you detach the ISDN cable, detach the end away from the router first to avoid possible electric shock.
Chapter 2 Installation Installing Your Router Figure 2-5 Connecting ISDN to Cisco 802 or Cisco 804 Routers Cisco 804 router HUB NO HU B Cisco 80 ETHERN ET 10 BA SE T 4 CONSOL E ISDN U 0 1 2 PHONE 3 1 2 ISDN wall jack 1. Connect red cable to red ISDN U port. 2. Connect other end of cable to ISDN wall jack.
Chapter 2 Installation Installing Your Router To connect an IDSL line to Cisco 802 IDSL and Cisco 804 IDSL routers, follow the steps in Figure 2-6. Figure 2-6 Connecting the IDSL Cable to Cisco IDSL Routers Cisco 804 IDSL router TO HUB TO PC ETHERN Cisco 80 4 IDSL ET 10 BA SE T CONSOL E IDSL 1 2 3 4 IDSL wall jack 1. Connect red cable to red IDSL port. 2. Connect other end of cable to IDSL wall jack.
Chapter 2 Installation Installing Your Router To connect a digital telephone, follow the steps in Figure 2-7. You must provide the following equipment: • NT1 with two S/T interfaces and one U interface. • Telephone cable to connect digital telephone. (This cable is usually provided with the telephone.) • ISDN U cable that connects the NT1 to the ISDN wall jack.
Chapter 2 Installation Installing Your Router telephones, faxes, or modems to work properly with the router phone ports. For example, in the United Kingdom, you must buy an adapter that also provides a master socket, which causes incoming calls to ring the connected devices. For information on recommended master sockets, see Table 2-3. Warning This equipment contains a ring signal generator (ringer), which is a source of hazardous voltage.
Chapter 2 Installation Installing Your Router Connecting a Terminal or PC You can connect either a terminal or a PC from which you can configure the software via the CLI or troubleshoot. To connect a terminal or PC, follow the steps in Figure 2-9. Figure 2-9 Connecting Terminal or PC HUB NO HU ETHER B NET 10 11680 Cisco 804 router Cisco 80 4 BASE T CONSOL E ISDN U 0 1 PHONE 2 3 1 2 1. Connect light blue cable to light blue CONSOLE port. 3. Connect DB-9 connector to terminal or PC.
Chapter 2 Installation Mounting Your Router Connecting the Power Supply To connect the power supply, follow the steps in Figure 2-10. Warning The device is designed to work with TN power systems. Warning This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that a fuse or circuit breaker no larger than 120 VAC, 15A U.S. (240 VAC, 16A international) is used on the phase conductors (all current-carrying conductors).
Chapter 2 Installation Mounting Your Router • Do not cover or obstruct router vents, which are located on the router sides. • You can stack a maximum of five routers atop one another. Mounting on a Wall You can mount your router on a wall or other vertical surface by using the molded mounting brackets on the bottom of the router and two number-six, 3/4-in. (M3.5 x 20 mm) screws. You must provide the screws. Figure 2-11 shows the mounting brackets.
Chapter 2 Installation Verifying Installation Figure 2-12 Mounting Router on Wall 5 1. Secure two screws 7 8 inches (19.35 cm) apart in a wall and 18 in. (0.32 cm) from the wall. . 5 in Front panel m) Wall-mount screw 5c .3 19 ( 7 8 Wall Mounting brackets Wall-mount screw 2. Hang router on screws. in. (0.32 cm) 11672 1 8 Wall Screw Maximum distance 6 ft (18 m) 3. Place power supply on horizontal surface.
Chapter 2 Installation Verifying Installation Table 2-4 Verifying Installation Power/Link LEDs To Check Normal Patterns Power OK On To hub, server, PC, or workstation • Cisco 801, 802, and 802 IDSL routers: LINK, LAN, LAN RXD, and LAN TXD • Cisco 803 and Cisco 804 routers: LKØ, LK1, LK2, LK3, LAN, LAN RXD, and LAN TXD • • LINK, LKØ, LK1, LK2, LK3, ETHERNET 1, 2, 3, 4, LAN: On. LAN is on when indicated Ethernet port sends or receives a packet.
Chapter 2 Installation Where to Go from Here Table 2-4 Verifying Installation (continued) Power/Link LEDs To Check To digital telephone LINE, CH1, CH1 RXD, CH1 TXD, CH2, CH2 RXD, and CH2 TXD To analog PH1 and PH21 telephone, fax, or modem Normal Patterns • LINE, CH1, and CH2: On. CH1 or CH2 is on when the router has an active voice connection. • CH1 RXD, CH2 RXD: Blinking when indicated ISDN B channel receives a packet.
C H A P T E R 3 Troubleshooting This chapter describes problems that could occur with the Cisco 800 series router hardware, reasons for the problems, and steps to solve the problems. The problems are grouped as follows: • Problems during first startup • Problems after first startup • Problems after router is running For information on problems that could occur with the software, refer to the Cisco 800 Series Routers Software Configuration Guide.
Chapter 3 Troubleshooting Problems During First Startup Problems During First Startup Table 3-1 lists problems that could occur after you turn on the power switch for the first time. Table 3-1 Problems During First Startup Symptom Problem Solutions All LEDs, including OK LED, are off. No power to router. Perform the following steps in the following order: • Make sure that the power switch is ON. • Make sure that all connections to and from the power supply are securely connected.
Chapter 3 Troubleshooting Problems After First Startup Problems After First Startup Table 3-2 lists problems that could occur after the router has power for the first time. Table 3-2 Problems After First Startup Symptom No link to an Ethernet device. (On Cisco 801, Cisco 802, and 802 IDSL routers, the LINK LED on the back panel is off. On Cisco 803 and 804 routers, the LKØ, LK1, LK2, or LK3 LED on the front panel is off.
Chapter 3 Troubleshooting Problems After First Startup Table 3-2 Problems After First Startup (continued) Symptom Problem • Solutions One of the following cable-related problems: Perform the following tasks in the following order: • To make sure you have cabled the ISDN or IDSL port correctly, see the “Connecting an ISDN Line” or “Connecting an IDSL Line” sections in Chapter 2, “Installation.” • Make sure the connectors at both ends of each cable are securely connected.
Chapter 3 Troubleshooting Problems After Router Is Running Table 3-2 Symptom Problems After First Startup (continued) Problem • Solutions Problem with ISDN line. • Contact your telephone service provider to determine if there is a problem with your line. • If the problem continues, call your Cisco reseller. Problems After Router Is Running Table 3-3 lists problems that could occur after the router has been up and running for a while.
Chapter 3 Troubleshooting Problems After Router Is Running Table 3-3 Problems After Router Is Running (continued) Symptom Problem Problems with ISDN or IDSL link. (CH1, CH1 RXD, CH1 TXD, CH2, CH2 RXD, or CH2 TXD are off.) • Solutions A cable-related problem: – Disconnected • If the problem continues, call your Cisco reseller. • Make sure the connectors at both ends of each cable are securely connected. • Make sure each cable is not physically damaged. If one is damaged, replace it. cable.
Chapter 3 Troubleshooting When Contacting Your Cisco Reseller Table 3-3 Problems After Router Is Running (continued) Symptom Problem Connection to analog telephone, fax machine, or modem is lost. (PH1 or PH2 LED on Cisco 803 and 804 routers is off.) • Solutions A cable-related problem: – Disconnected • If the problem continues, call your Cisco reseller. • Make sure the connectors at both ends of the cable are securely connected. • Make sure the cable is not physically damaged.
Chapter 3 Troubleshooting When Contacting Your Cisco Reseller Cisco 800 Series Routers Hardware Installation Guide 3-8 78-5373-04
C H A P T E R A ISDN and IDSL Concepts This appendix provides further explanation of ISDN and IDSL concepts. The Cisco 800 series routers provide one basic rate interface (BRI). The ISDN BRI service provided by your telephone service provider offers two bearer channels (B channels) and one data channel (D channel). The B channel operates at 64 kbps and carries user data.
Chapter A ISDN and IDSL Concepts Cisco 800 Series Routers Hardware Installation Guide A-2 78-5373-04
A P P E N D I X B Specifications and Cables This appendix provides system, port, and cabling specifications for the Cisco 800 series routers. System Specifications Table B-1 outlines the system specifications for the routers. Table B-1 System Specifications Description Design Specification Physical Dimensions Dimensions (H x W x D) 2.0 x 9.7 x 8.3 in. (5.1 x 24.6 x 21.1 cm) Weight (does not include desktop power supply) Cisco 801 router: 1.39 lb (0.63 kg) Cisco 802 router: 1.42 lb (0.
Appendix B Specifications and Cables Port Connector Pinouts For information on regulatory compliance, refer to the Regulatory Compliance and Safety Information for Cisco 800 Series Routers document that shipped with your router. Warning Ultimate disposal of this product should be handled according to all national laws and regulations.
Appendix B Specifications and Cables Port Connector Pinouts Table B-4 Cisco 804 IDSL Ethernet Connector Pinouts for Port 1 Only (RJ-45) Pin Function (TO HUB/TO PC Button – OUT Position) Function (TO HUB/TO PC Button – IN Position) Pin Function (TO HUB/TO PC Button – OUT Position) Function (TO HUB/TO PC Button – IN Position) A1 RX+ TX+ A2 RX– TX– A3 TX+ RX+ A4 Unused Unused A5 Unused Unused A6 TX– RX– A7 Unused Unused A8 Unused Unused Table B-5 Cisco 803 and Cisco 804 Ether
Appendix B Specifications and Cables Port Connector Pinouts Table B-6 Cisco 804 IDSL Ethernet Connector Pinouts for Ports 2, 3, and 4 (RJ-45) (continued) Pin Function Pin Function D3 TX2+ D4 Unused D5 Unused D6 TX2– D7 Unused D8 Unused Table B-7 Console Connector Pinouts (RJ-45) Pin Function 1 RTS 2 DTR 3 TXD 4 GND 5 GND 6 RXD 7 DSR 8 CTS Cisco 800 Series Routers Hardware Installation Guide B-4 78-5373-04
Appendix B Specifications and Cables Port Connector Pinouts The console port is configured as a data communications equipment (DCE) device.
Appendix B Specifications and Cables Cabling Specifications Table B-10 IDSL Connector Pinouts (RJ-45) Pin Function 5 IDSL interface network connection (Ring) 6 Unused 7 Unused 8 Unused Table B-11 Telephone Connector Pinouts (RJ-11) Pin Function 1 Unused 2 Unused 3 Ring 4 Tip 5 Unused 6 Unused Table B-12 Power Connector Pinouts Pin Function 1 ROF 2 RTN 3 Unused 4 Unused 5 +5 6 RTN 7 –71 8 –24 Cabling Specifications This section provides the following cabling sp
Appendix B Specifications and Cables Cabling Specifications Ethernet Cable Specifications Table B-13 lists the specifications for straight-through and crossover Ethernet cables. Refer to the Glossary for definitions of straight-through Ethernet cable and crossover Ethernet cable.
Appendix B Specifications and Cables Cabling Specifications Cisco 800 Series Routers Hardware Installation Guide B-8 78-5373-04
GLOSSARY Numerics 10BASE-T The 10-Mbps baseband Ethernet specification that uses two pairs of twisted-pair cabling (Category 3 or 5): one pair for transmitting data and the other for receiving data. B BRI Basic Rate Interface. An ISDN interface composed of two bearer channels (B channels) and one data channel (D channel) for circuit-switched communication of voice, video, and data.
Glossary EMI Electromagnetic interference. The interference by electromagnetic signals that can cause reduced data integrity and increased error rates on transmission channels. ESD Electrostatic discharge. A transfer of electrostatic charge between bodies of different electrostatic potentials, such as an operator and a piece of electrical equipment. ESD occurs when electronic components are improperly handled and can damage equipment and impair electrical circuitry.
Glossary S straight-through Ethernet cable A cable that wires a pin to its equivalent pin. This cable connects two dissimilar devices, for example, a data terminal equipment (DTE) and a data communications equipment (DCE) device. A straight-through Ethernet cable is the most common cable used. T TO HUB/TO PC button The Cisco 802 IDSL and Cisco 804 IDSL routers provide a TO HUB/TO PC button that is equivalent to the HUB/NO HUB button on the other Cisco 800 series routers.
Glossary Cisco 800 Series Routers Hardware Installation Guide GL-4 78-5373-04
INDEX modem A PC accessory kit 2-4 2-15 2-9, 2-17 power supply adapter, included 2-4 server altitude specifications analog telephone B-1 2-9 telephones 2-15 2-18 2-14, 2-15 terminal or PC workstation 2-17 2-9 console port B description back panels, illustrated B channels A-1 illustrated 1-2 1-4 to 1-7 conventions, hazard brackets, illustrated BRI 1-4 to 1-7 vii 2-19 A-1 D damage C electrostatic discharge (ESD) cable lock, illustrated 1-4 to 1-7 cables router, preventing
Index F fax, connecting 2-15 Flash memory, adding modem, connecting 2-15 mounting the router 2-18 vii 1-4 to 1-6 N network device button settings 2-6 to 2-7 NT1 feature 2-6 to 2-7 1-2 2-8 humidity specifications B-1 P panels, illustrated I PC, connecting IDSL concepts 1-4 to 1-7 M 1-3 HUB/NO HUB button hubs, connecting 1-3 to 1-6 B-1 hazard statements, defined settings illustrated locking power connector, illustrated H illustrated 1-7 1-2 frequency specifications front pa
Index unpacking the router S S/T interface 2-4, ?? to 2-4 A-1 safety warnings V 2-2 server, connecting 2-9 settings, network devices voltage specifications specifications cabling B-6 system B-1 B-1 2-6 to 2-7 W wall brackets, illustrated startup problems 3-2 wall mounting T 2-19 to 2-20 warnings, installation 2-2 weight specifications B-1 workstation, connecting table mounting 2-19 2-9 2-18 telephone connecting 2-14, 2-15 ports described 1-2 illustrated 1-5, 1-6 tempera
Index Cisco 800 Series Routers Hardware Installation Guide IN-4 78-5373-04
