Cisco 1700 Router Hardware Installation Guide Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
CCSP, CCVP, the Cisco Square Bridge logo, Follow Me Browsing, and StackWise are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, and iQuick Study are service marks of Cisco Systems, Inc.
CONTENTS About This Guide ix Audience and Scope ix Organization x Related Publications x Conventions xi Obtaining Documentation xiv Cisco.
Contents Amounts of Memory 1-9 Unpacking the Router 1-10 Additional Required Equipment 1-10 CHAPTER 2 Installing the Cisco 1700 Router 2-1 Before Installing the Router 2-1 Connecting the Router to Your Local Network 2-2 Installing WAN Interface Cards 2-4 Safety Information 2-4 Installing a WAN Interface Card 2-5 Connecting Power to the Router 2-8 Verifying Your Installation 2-10 Optional Installation Steps 2-11 Connecting a PC 2-11 Connecting a Modem 2-12 Wall-Mounting 2-14 CHAPTER 3 Troubleshooting
Contents Troubleshooting ISDN 3-10 APPENDIX A Technical Specifications A-1 APPENDIX B Cabling Specifications B-1 Ethernet Cables B-2 Ethernet Network Cabling Guidelines B-3 Console Cable and Adapters B-3 APPENDIX C Installing and Upgrading Router Memory C-1 Opening the Chassis C-2 Locating Memory C-4 Installing a Mini-Flash Module C-5 Removing a Mini-Flash Module C-6 Installing a DIMM C-7 Closing the Chassis C-8 APPENDIX D Ordering and Configuring an ISDN Line D-1 ISDN BRI Line Configuration Re
Contents Cisco 1700 Router Hardware Installation Guide viii 78-5405-03
About This Guide This section discusses the intended audience, scope, and organization of the Cisco 1700 Router Hardware Installation Guide and defines the conventions used to convey instructions and information. Cisco documentation and additional literature are available on the World Wide Web at http://www.cisco.com, http://www-china.cisco.com, or http://www-europe.cisco.com. If you are reading Cisco product documentation on the World Wide Web, you can submit comments electronically.
Organization This guide is organized as follows: • The chapter “Cisco 1700 Router Overview” describes the router features and describes the front-panel LEDs, rear-panel LEDs, and connectors. • The chapter “Installing the Cisco 1700 Router” describes how to install the router by connecting cables, power, and installing WAN interface cards. • The chapter “Troubleshooting” describes some problems that you might have with the router and how to solve these problems.
• Cisco IOS command reference and configuration guides provide complete information about all Cisco IOS CLI commands and how to use them, as well as information on designing and configuring local and wide-area networks. Conventions This guide uses the following conventions for instructions and information: Note Caution This note symbol means reader take note. Notes contain helpful suggestions or references to materials not contained in this manual. This caution symbol means reader be careful.
Warning Varoitus Tämä varoitusmerkki merkitsee vaaraa. Olet tilanteessa, joka voi johtaa ruumiinvammaan. Ennen kuin työskentelet minkään laitteiston parissa, ota selvää sähkökytkentöihin liittyvistä vaaroista ja tavanomaisista onnettomuuksien ehkäisykeinoista. Tässä julkaisussa esiintyvien varoitusten käännökset löydät laitteen mukana olevasta Regulatory Compliance and Safety Information -kirjasesta (määräysten noudattaminen ja tietoa turvallisuudesta).
Warning Advarsel Dette varselsymbolet betyr fare. Du befinner deg i en situasjon som kan føre til personskade. Før du utfører arbeid på utstyr, må du vare oppmerksom på de faremomentene som elektriske kretser innebærer, samt gjøre deg kjent med vanlig praksis når det gjelder å unngå ulykker.
Obtaining Documentation Cisco documentation and additional literature are available on Cisco.com. Cisco also provides several ways to obtain technical assistance and other technical resources. These sections explain how to obtain technical information from Cisco Systems. Cisco.com You can access the most current Cisco documentation at this URL: http://www.cisco.com/univercd/home/home.htm You can access the Cisco website at this URL: http://www.cisco.
Ordering Documentation You can find instructions for ordering documentation at this URL: http://www.cisco.com/univercd/cc/td/doc/es_inpck/pdi.htm You can order Cisco documentation in these ways: • Registered Cisco.com users (Cisco direct customers) can order Cisco product documentation from the Ordering tool: http://www.cisco.com/en/US/partner/ordering/ • Nonregistered Cisco.
• Obtain assistance with security incidents that involve Cisco products. • Register to receive security information from Cisco. A current list of security advisories and notices for Cisco products is available at this URL: http://www.cisco.com/go/psirt If you prefer to see advisories and notices as they are updated in real time, you can access a Product Security Incident Response Team Really Simple Syndication (PSIRT RSS) feed from this URL: http://www.cisco.com/en/US/products/products_psirt_rss_feed.
Obtaining Technical Assistance For all customers, partners, resellers, and distributors who hold valid Cisco service contracts, Cisco Technical Support provides 24-hour-a-day, award-winning technical assistance. The Cisco Technical Support Website on Cisco.com features extensive online support resources. In addition, Cisco Technical Assistance Center (TAC) engineers provide telephone support. If you do not hold a valid Cisco service contract, contact your reseller.
Submitting a Service Request Using the online TAC Service Request Tool is the fastest way to open S3 and S4 service requests. (S3 and S4 service requests are those in which your network is minimally impaired or for which you require product information.) After you describe your situation, the TAC Service Request Tool provides recommended solutions. If your issue is not resolved using the recommended resources, your service request is assigned to a Cisco TAC engineer.
Severity 3 (S3)—Operational performance of your network is impaired, but most business operations remain functional. You and Cisco will commit resources during normal business hours to restore service to satisfactory levels. Severity 4 (S4)—You require information or assistance with Cisco product capabilities, installation, or configuration. There is little or no effect on your business operations.
• Internet Protocol Journal is a quarterly journal published by Cisco Systems for engineering professionals involved in designing, developing, and operating public and private internets and intranets. You can access the Internet Protocol Journal at this URL: http://www.cisco.com/ipj • World-class networking training is available from Cisco. You can view current offerings at this URL: http://www.cisco.com/en/US/learning/index.
C H A P T E R 1 Cisco 1700 Router Overview This chapter introduces the Cisco 1700 router, also referred to in this guide as the router, and covers the following topics: • Key Features • Rear-Panel Ports and LEDs • Front-Panel LEDs • Router Memory • Unpacking the Router • Additional Required Equipment Cisco 1700 Router Hardware Installation Guide 78-5405-03 1-1
Chapter 1 Cisco 1700 Router 12154 Figure 1-1 Cisco 1700 Router Overview PWR WIC0 ACT/C WI H0 AC C1 T/CH0 ETH ACT OK ACT/C H1 AC T/CH1 Cisco 1700 SER COL IES RO UT ER Cisco 1700 Router Hardware Installation Guide 1-2 78-5405-03
Chapter 1 Cisco 1700 Router Overview Key Features The Cisco 1700 router is a small, modular desktop router that links small- to medium-size remote Ethernet and FastEthernet LANs over one to four WAN connections to regional and central offices. lists the router key features. Figure 1-2 Key Features Feature Description One FastEthernet (10/100BaseTX) port • Operates in full- or half-duplex mode (with manual override available). • Supports autosensing for 10- or 100-Mbps operation.
Chapter 1 Cisco 1700 Router Overview Rear-Panel Ports and LEDs This section describes the router rear panel ports and LEDs, which are shown in Figure 1-3 and described in Table 1-1 and Table 1-2.
Chapter 1 Cisco 1700 Router Overview Table 1-1 Rear-Panel Connectors (Continued) Connector/Slot Label/Color Description WAN interface card slot (WIC1) No label Supports one Cisco WAN interface card. For detailed information, refer to the Cisco WAN Interface Cards Hardware Installation Guide that comes with every card. Power socket +5, +12, -12 VDC Connects the router to the external power supply.
Chapter 1 Cisco 1700 Router Overview Front-Panel LEDs Use the router front-panel LEDs to determine network activity and status on the Ethernet port and on the WAN interface card ports. The front-panel LEDs are illustrated in Figure 1-4 and described in Table 1-3. Front-Panel LEDs WIC0 WIC1 ETH PWR ACT/CH0 ACT/CH0 ACT OK ACT/CH1 ACT/CH1 COL 12155 Figure 1-4 Table 1-3 Front-Panel LEDs LED Label Color Description PWR Green On means that DC power is being supplied to the router.
Chapter 1 Cisco 1700 Router Overview Table 1-3 Front-Panel LEDs (Continued) LED Label Color Description Green Serial and DSU/CSU cards—Blinks when data is being sent to or received from the port on the card in the WICØ slot. WICØ ACT/CHØ ISDN cards—On solid when the first ISDN B channel is up for the card in the WICØ slot. 2-port serial cards—Blinks when there is data being sent to or received from the first port on the 2-port card in the WICØ slot.
Chapter 1 Cisco 1700 Router Overview Router Memory This section describes the types of memory stored in the router and how to find out how much of each type of memory is stored in the router. For instruction on how to upgrade memory in the router, refer to the “Installing and Upgrading Router Memory” appendix later in this guide. Types of Memory The Cisco 1700 router has the following types of memory: • Dynamic random-access memory (DRAM)—This is the main storage memory for the router.
Chapter 1 Cisco 1700 Router Overview Amounts of Memory Use the show version command to view the amount of DRAM, NVRAM, and Flash memory stored in your router. The following example of the show version command output in bold text displays the amount of memory stored in this router. 1700# show version Cisco Internetwork Operating System Software IOS (tm) C1700 Software (C1700-Y-M), Version 12.X(XX)T [cisco-ferrari2 121] Copyright (c) 1986-1998 by cisco Systems, Inc. Compiled Tue 26-May-98 19:58 by . . . . .
Chapter 1 Cisco 1700 Router Overview Unpacking the Router Table 1-4 lists the items that come with your router. All these items are in the accessory kit that is inside the box that your router came in.
Chapter 1 Cisco 1700 Router Overview Equipment When You Use It Cisco WAN interface card In order to make a WAN connection, the Cisco 1700 router must have a supported WAN interface card installed. The router supports up to two cards. You can order the cards when ordering the router, and they will be installed for you. You can order the cards separately, after receiving the router, and install them yourself.
Chapter 1 Cisco 1700 Router Overview Cisco 1700 Router Hardware Installation Guide 1-12 78-5405-03
C H A P T E R 2 Installing the Cisco 1700 Router This chapter of installation procedures for the Cisco 1700 router includes the following sections: • Before Installing the Router • Connecting the Router to Your Local Network • Installing WAN Interface Cards • Connecting Power to the Router • Verifying Your Installation • Optional Installation Steps Before Installing the Router The Cisco 1700 router is shipped ready for desktop mounting.
Chapter 2 Installing the Cisco 1700 Router Warning Read the installation instructions before you connect the system to its power source. Warning Do not work on the system or connect or disconnect cables during periods of lightning activity. Caution Do not place anything on top of the router that weighs more than 10 pounds (4.5 kgs). Excessive weight on top of the router could damage the chassis.
Chapter 2 Installing the Cisco 1700 Router Follow these steps to connect the router to the local network: Figure 2-1 Connect one end of the cable to the yellow Ethernet port (labeled 10/100 ETHERNET). Step 2 Connect the other end of the cable to a network port on the hub or switch.
Chapter 2 Installing the Cisco 1700 Router Installing WAN Interface Cards The Cisco 1700 router supports one or two Cisco WAN interface cards. Each card has one or two WAN ports. This section describes the general procedure for installing a card in the Cisco 1700 router.
Chapter 2 Installing the Cisco 1700 Router Warning Do not work on the system or connect or disconnect cables during periods of lightning activity. (To see translated versions of this warning, refer to the Regulatory Compliance and Safety Information for the Cisco 1700 document that came with the router.) Caution Do not connect a WAN cable to the card until you have completed the installation procedure.
Chapter 2 Installing the Cisco 1700 Router Installing the Cards Follow these steps to install the card in a Cisco 1700 router: Step 1 Make sure that the power switch is set to the STANDBY position ( ) and that the power cable is not connected to the power socket on the rear panel. Step 2 Loosen the thumbscrews on the WAN interface card-slot cover on the rear panel, as shown in Figure 2-2.
Chapter 2 Installing the Cisco 1700 Router Insert the card in the slot and gently push it into the router until the front panel of the card is flush with the rear panel of the router. Step 6 Tighten the screws.
Chapter 2 Installing the Cisco 1700 Router Connecting Power to the Router Read the following warnings before connecting the router to power. Warning The power supply is designed to work with TN power systems. Warning This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that a fuse or circuit breaker no larger than 120VAC, 15AU.S. (240VAC, 16A international) is used on the phase conductors (all current-carrying conductors).
Chapter 2 Installing the Cisco 1700 Router Connecting the Power Supply 12162 Figure 2-4 CONS OLE 100 LNK TD FDX 10/10 0 ET HERN SEE ET AUX MAN UAL BEF ORE CD 0 OK RD WIC LP 1720 AL Cisco INSTAL LATION WIC DSU 56K 1 OK +5, +1 2, -1 2 VD C Power socket Cisco 1700 Router Hardware Installation Guide 78-5405-03 2-9
Chapter 2 Installing the Cisco 1700 Router Verifying Your Installation You can verify that you have correctly installed the router by checking the following LEDs: • PWR (front panel)—On when power is being supplied to the router. • OK (front panel)—On when the router software is loaded and functional. Blinking means that the router is performing a power-on self-test (POST). • WICØ/WIC1 OK (rear panel)—On when a WAN interface card is correctly installed in the corresponding WAN interface card slot.
Chapter 2 Installing the Cisco 1700 Router Optional Installation Steps This section describes some installation steps that you might or might not use, depending on your site and how you are configuring the router. This chapter describes the following procedures: • Connecting a PC • Connecting a Modem • Wall-Mounting Connecting a PC If you want to configure the router using the Cisco IOS command-line interface, you must connect the router console port to a terminal or PC.
Chapter 2 Connecting the Console Cable to the Router 12160 Figure 2-5 Installing the Cisco 1700 Router 0 OK CONS OLE LNK 10/100 ETH SEE MANU CD 100 TD FDX RD WIC LP 0 AL o 172 AL BE FORE AUX INSTAL DSU 56K LATION WIC 1 OK +5, +1 2, -1 2 VD C Console port ue console cable To PC or terminal Connecting a Modem When a modem is connected to the auxiliary port, a remote user can dial into the router and configure it.
Chapter 2 Installing the Cisco 1700 Router Connecting a Modem to the Router 12161 Figure 2-6 LNK 10/10 0 ET HERN ET SEE MAN UAL BEF ORE AUX CD 100 TD FDX RD CONS OLE 0OK LP WIC AL 720 INST ALLATIO N WIC DSU 56K 1 OK +5, +1 2, -12 VDC AUX port (RJ-45) Modem m cable DB-9-to-DB-25 adapter EIA/TIA-232 Cisco 1700 Router Hardware Installation Guide 78-5405-03 2-13
Chapter 2 Installing the Cisco 1700 Router Wall-Mounting The Cisco 1700 router can be wall-mounted using two number 6, 3/4-inch screws and the molded mounting brackets on the bottom of the hub. You must provide the screws. We recommend using pan-head or round-head screws. Figure 2-7 Wall-Mount Brackets—Bottom of Router Front panel of router Mounting bracket Bottom of router 3.75" (9.52 cm) 12016 Mounting bracket To mount the router on a wall or other surface: Step 1 Install the two screws 3.
Chapter 2 Installing the Cisco 1700 Router Step 2 Caution Hang the router on the screws with either the left side or right side mounting brackets so that: • The LEDs are visible to the user—The LEDs indicate the router operating status, so the LEDs should be easily visible. • The power supply does not hang from its cable—If the power supply is not supported, it might disconnect from the cable that connects it to the router.
Chapter 2 Installing the Cisco 1700 Router Cisco 1700 Router Hardware Installation Guide 2-16 78-5405-03
C H A P T E R 3 Troubleshooting Use the information in this chapter to help isolate problems you might encounter with the Cisco 1700 router or to rule out the router as the source of the problem. This chapter contains the following sections: • Contacting Cisco or Your Reseller • Recovering a Lost Password • Problem Solving • Troubleshooting ISDN Contacting Cisco or Your Reseller If you cannot locate the source of a problem, contact your local reseller for advice.
Chapter 3 Troubleshooting Recovering a Lost Password This section describes how to recover a lost enable or enable secret password. The process of recovering a password consists of the following major steps: Note • Change the Configuration Register • Reset the Router • Reset the Password (for lost enable secret passwords only) • Reset the Configuration Register Value See the “Hot Tips” section on Cisco Connection Online (CCO) for additional information on replacing enable secret passwords.
Chapter 3 Troubleshooting Step 4 At the user EXEC prompt (Router>), enter the show version command to display the existing configuration register value (shown in bold at the bottom of this example output): Router> show version Cisco Internetwork Operating System Software IOS (tm) C1700 Software (C1700-BNOR2SY56I-M), Experimental Version 12.0(19980725:020859) [aiyagari-devtest_0724 100] Copyright (c) 1986-1998 by cisco Systems, Inc.
Chapter 3 Note Troubleshooting To enable break, enter the config-register 0x01 EXEC command. Reset the Router Step 1 Do one of the following: • • Note If break is enabled, go to Step 2. If break is disabled, turn the router OFF, wait 5 seconds, and turn it ON again. Within 60 seconds, press the Break key. The terminal displays the ROM monitor prompt. Go to Step 3. Some terminal keyboards have a key labeled Break.
Chapter 3 Troubleshooting Press RETURN to get started! Step 6 Press Return. The following prompt appears: Router> Step 7 Enter the enable command to enter privileged EXEC mode.
Chapter 3 Troubleshooting Step 3 Enter the config-register command and the original configuration register value that you recorded in Step 5. Step 4 Press Ctrl-Z to exit configuration mode.
Chapter 3 Troubleshooting • Power system—Check the external power source, power cable, router power supply, and circuit breaker. Check for inadequate ventilation or air circulation that might cause overheating. • ISDN configuration—Consider ISDN-specific hardware and software configurations (ISDN BRI WAN interface cards only). OK LED Diagnostics Use the front-panel OK LED to determine any problems with the router. When the router first boots up, it performs a power-on self-test (POST).
Chapter 3 Table 3-2 Troubleshooting Troubleshooting WAN Interface Cards Symptom Possible Cause(s) Router does not recognize WAN interface card • Confirm that the Cisco IOS software version installed in the router supports the WAN interface card. The Cisco WAN Interface Cards Hardware Installation Guide lists the software requirements for each card. • Make sure that the card is correctly installed in the router.
Chapter 3 Table 3-2 Troubleshooting Troubleshooting WAN Interface Cards (Continued) Symptom Possible Cause(s) Router boots, but the console screen is frozen. • Make sure the console cable is securely connected to the router and to the PC or terminal. • Verify that the parameters for your terminal are set to the following: — 9600 baud — 8 data bits — No parity generated or checked — 1 stop bit Router powers on and boots only when a particular WAN interface card is removed from the router.
Chapter 3 Table 3-3 Troubleshooting Troubleshooting the Power System Symptom Possible Cause(s) The front-panel PWR LED is on, the front-panel OK LED is off, and the router does not pass console or EIA data. The power supply has failed. Troubleshooting ISDN Because ISDN uses many variables and supports many different configurations, it sometimes can cause problems for the router. This section describes problems related to the ISDN line that might occur.
Chapter 3 Troubleshooting Table 3-4 Troubleshooting ISDN WAN Interface Card Symptom(s) Check the Following Possible Causes Router is on, but OK LED on card is off. • Is the OK LED on the router front panel on? • If no, the router might be malfunctioning. Contact your Cisco reseller. • Are all ISDN cables properly connected? • If yes, the ISDN line might be malfunctioning. Check with your ISDN service provider. • Is the NT1 on? • If no, the NT1 might be malfunctioning.
Chapter 3 Table 3-4 Troubleshooting ISDN (Continued) WAN Interface Card Symptom(s) Check the Following Card cannot make a connection to the remote router. Use show isdn status command to check the following: ISDN S/T or ISDN U Troubleshooting Possible Causes • Does the current ISDN switch type match actual switch type being used? • Use the isdn switch-type command to configure correct switch type.
A P P E N D I X A Technical Specifications Table A-1 lists hardware and operating specifications for the Cisco 1700 router. Table A-1 Router Specifications Description Specification Console port RJ-45 Auxiliary port RJ-45 Ethernet port RJ-45 Dimensions HxWxD 3.1 x 11.2 x 8.7 in. (7.85 x 28.4 x 22.1 cm) Weight 2.6 lbs (1.18 kg) With two WAN interface cards 2.9 lbs ( 1.32 kg) Power supply External Universal AC/DC switching—Supplies +5V, +12V, and –12V On-board Supplies 3.
Appendix A Technical Specifications Cisco 1700 Router Hardware Installation Guide A-2 78-5405-03
A P P E N D I X B Cabling Specifications This appendix describes cables and cabling guidelines for the Cisco 1700 router and contains the following sections: Note • Ethernet Cables • Ethernet Network Cabling Guidelines • Console Cable and Adapters For information about cables used with Cisco WAN interface cards, refer to the Cisco WAN Interface Cards Hardware Installation Guide that comes with each of the cards.
Appendix B Cabling Specifications Ethernet Cables This section describes the Ethernet cables that are used to connect the router to your local Ethernet network. A 10/100BaseTX router, like the Cisco 1700 router, requires Category 5 unshielded twisted-pair (UTP) or shielded twisted-pair (STP) cable. Table B-1 Straight-Through Ethernet Cable (RJ-45-to-RJ-45) Pinouts RJ-45 Pin1 Signal Direction RJ-45 Pin 1 TX+ —> 1 2 TX– —> 2 3 RX+ <— 3 RX– <— 6 6 1.
Appendix B Cabling Specifications Ethernet Network Cabling Guidelines Table B-2 describes some guidelines for creating Ethernet networks. Figures might vary, depending on the manufacturer of the network equipment.
Appendix B Table B-3 Cabling Specifications Console Cable and Adapter Pinouts Console (DTE) Console Port Console Cable Adapter Adapter Terminal (DTE) Signal RJ-45 Pin RJ-45 Pin DB-9 Pin DB-25 Pin Signal RTS 1 8 8 5 CTS DTR 2 7 6 6 DSR TXD 3 6 2 3 RXD GND 4 5 5 7 GND GND 5 4 5 7 GND RXD 6 3 3 2 TXD DSR 7 2 4 20 DTR CTS 8 1 7 4 RTS Figure B-1 Identifying a Rollover Cable Pin 1 on one connector and pin 8 on the other connector should be the same
A P P E N D I X C Installing and Upgrading Router Memory This chapter describes how to install or upgrade memory in your Cisco 1700 router and includes the following sections: Warning • Opening the Chassis • Locating Memory • Installing a Mini-Flash Module • Installing a DIMM • Closing the Chassis During this procedure, wear grounding wrist straps to avoid ESD damage to the router. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself.
Appendix C Installing and Upgrading Router Memory Opening the Chassis In order to upgrade Cisco 1700 router memory, you must open the chassis. Opening the chassis requires a number one Phillips screwdriver. Follow these steps to open the chassis: Step 1 Make sure the router is turned OFF and is disconnected from the power supply. Step 2 Turn the router upside down, and rest the top of the router on a flat surface.
Appendix C Installing and Upgrading Router Memory Figure C-1 Removing the Chassis Screws #1 Phillips screwdriver +5 ,+ 12 ,12 WIC 1O K DS U 56 K ON ATI ALL OR E INST CD LB EF NU A EM A SE AU X TD 12615 10 /1 00 E RD LP AL TH K 0 X 10 FD WIC co Cis LN CO NS OL E 0O K 20 17 Rear panel Top of router Step 5 Gently pull the top of the router (which is facing up toward you) up and away from the bottom of the router (which is resting on the flat surface).
Appendix C Installing and Upgrading Router Memory Locating Memory Figure C-2 shows where to install DIMMs and mini-Flash modules on the router motherboard.
Appendix C Installing and Upgrading Router Memory Installing a Mini-Flash Module You can install a mini-Flash module (shown in Figure C-3) to increase the amount of Flash memory in the router. Mini-Flash Module 12612 Figure C-3 Notched edge Take the following steps to install a mini-Flash module on the motherboard: Step 1 Locate the module slot on the motherboard, shown in Figure C-2. Step 2 Hold the module with the notched edge away from you.
Appendix C Figure C-4 Installing and Upgrading Router Memory Installing a Mini-Flash Module WAN interface card slot 12613 Notched edge Mini-Flash module slot 45 degrees Removing a Mini-Flash Module Take the following steps to remove a mini-Flash module: Step 1 Insert your index finger between the mini-Flash module and the mini-Flash module release lever, as shown in Figure C-5. Step 2 Firmly pull the release lever away from the module until the module pops up and away from the module slot.
Appendix C Installing and Upgrading Router Memory Removing a Mini-Flash Module 12614 Figure C-5 Mini-Flash module release lever Installing a DIMM You can install a dual inline memory module (DIMM) to increase the amount of dynamic random-access memory (DRAM) in the router. Take the following steps to install a DIMM on the router motherboard. Step 1 Locate the DIMM slot on the motherboard, shown in Figure C-2.
Appendix C Step 5 Figure C-6 Installing and Upgrading Router Memory Firmly press the DIMM into the slot until the two DIMM slot guides on each side of the slot move up and over the end of the DIMM, as in Figure C-6. If the guides do not move up over the edge of the DIMM, move them with your hands.
Appendix C Installing and Upgrading Router Memory Figure C-7 Step 3 Line up the posts with the corresponding openings, as shown in Figure C-7, and carefully slide the posts into the openings, taking caution not to damage the router motherboard with the posts. Step 4 Replace the screws that you removed when opening the chassis. (See Figure C-1.
Appendix C Installing and Upgrading Router Memory Cisco 1700 Router Hardware Installation Guide C-10 78-5405-03
A P P E N D I X D Ordering and Configuring an ISDN Line This appendix describes how to order and configure an Integrated Services Digital Network (ISDN) Basic Rate Interface (BRI) line for use with a Cisco 1700 router with an ISDN BRI WAN interface card installed.
Appendix D Ordering and Configuring an ISDN Line • If the router is going to be the only device attached to the ISDN BRI line, ask for point-to-point service and a data-only line. • If you will be connecting another ISDN device (such as an ISDN telephone) to the ISDN BRI line, ask for point-to-multipoint service (subaddressing is required) and a voice-and-data line. ISDN BRI Switch Types ISDN BRI supports a variety of service provider switches.
Appendix D Ordering and Configuring an ISDN Line ISDN BRI Provisioning by Switch Type The ISDN BRI line is configured (provisioned) for different types of services by the ISDN BRI service provider. The person ordering the ISDN line must also order the provisioning described in this section. Table D-2 lists the provisioning that should be ordered for the router, based on the switch type.
Appendix D Ordering and Configuring an ISDN Line Switch Type Provisioning 5ESS National ISDN (NI1) BRI Terminal type = A 2 B channels for voice and data 2 directory numbers assigned by service provider 2 SPIDs required; assigned by service provider Set speed for ISDN calls to 56 kbps outside local exchange Directory number 1 can hunt to directory number 2 DMS-100 BRI 2 B channels for voice and data 2 directory numbers assigned by service provider 2 SPIDs required; assigned by service provider Functio
Appendix D Ordering and Configuring an ISDN Line Note SPIDs have significance only at the local-access ISDN interface. Every router that uses ISDN must be assigned SPIDs (if used by the service provider) by the service provider for that router. When the router connects to the service provider’s central office ISDN switch, it sends the SPIDs to the switch. If the router is not configured with the correct SPIDs, it cannot place or receive calls.
Appendix D Ordering and Configuring an ISDN Line Dial-on-Demand Routing To place calls on the ISDN interface, you must configure it with dial-on-demand routing (DDR). See the chapter “Configuring DDR” in the Wide-Area Networking Configuration Guide publication for detailed information about DDR. Bandwidth on Demand and Dial Backup See the chapter “Configuring DDR” in the Wide-Area Networking Configuration Guide publication for detailed information about bandwidth on demand and dial backup.
INDEX Numerics 5ESS Custom ISDN BRI switch D-3 5ESS National ISDN 1 (NI1) BRI switch D-4 See ISDN BRI C cables A console pinout B-4 Ethernet pinout B-2 accessory kit 1-10 included with router 1-10 adapter, included 1-10 requirements for Ethernet networks B-3 additional required equipment 1-10 serial 1-11 ANI you need to provide 1-10 See calling-line identification Automatic Number Identification See calling-line identification auxiliary port connecting 2-12 caller ID See calling-line identifi
Index enable 3-5 note xi enable secret 3-5 warning xi isdn spid D-5 Dial-on-Demand Routing See DDR isdn switch-type D-2 DIMM reset 3-4 show startup-config 3-5 installing C-7 show version 3-3 locating on router C-4 config-register command 3-4 DMS-100 ISDN BRI switch D-3 configuration register document displaying 3-4 audience ix setting 3-2, 3-4, 3-6 conventions xi configure terminal command 3-5, 3-6 organization x connecting related publications x Ethernet cable 2-2 DRAM description
Index specifications A-1 WAN interface cards 2-4 Integrated Services Digital Network See ISDN BRI F ISDN Flash memory description 1-8 installing C-5 See ISDN BRI ISDN BRI configuring bandwidth on demand D-6 locating on router C-4 DDR D-6 front panel illustration 1-2 dial backup D-6 LEDs requirements D-1 snapshot routing D-5 description 1-6 to 1-7 illustration 1-6 line configuration requirements D-1 point-to-multipoint service D-2 point-to-point service D-2 H hub provisioning D-3 to D-4 SPID
Index description 1-11 L support 1-3 LEDs modem, connecting to router 2-12 front panel description 1-6 to 1-7 illustration 1-6 N OK LED diagnostics 3-7 note, definition xi rear panel NT1 1-11 description 1-4 NVRAM, description 1-8 illustration 1-4 using to verify installation 2-10 O OK LED M description 1-6 memory diagnostics 3-7 description 1-8 opening chassis C-2 DIMM operating temperatures A-1 installing C-7 locating on router C-4 displaying amounts 1-9 P DRAM description 1-8 pas
Index power socket SPID D-4 connecting 2-8 configuring D-5 illustration 1-4 definition D-4 specifications A-1 switch problem solving 3-6 connecting to 2-3 PWR LED description 1-6 description 1-10 R T rear panel terminal emulation, settings 2-11 connectors troubleshooting description 1-4 cables 3-7 illustration 1-4 contacting Cisco 3-1 LEDs password recovery 3-2 to 3-6 description 1-5 power system 3-9 illustration 1-4 using the OK LED 3-7 recovering a lost password 3-2 WAN inter
Index slot specifications A-1 supported cards 1-3 troubleshooting 3-7 to 3-9 warning definition xi jewelry removal 2-4 lightning activity 2-2, 2-5 read instructions before installing 2-2 SELV circuits 2-2 telephone-network voltages 2-4 trained and qualified personnel 2-4 WIC0 ACT/CH0 LED description 1-7 WIC0 ACT/CH1 LED description 1-7 Cisco 1700 Router Hardware Installation Guide IN-6 78-5405-03
