Cisco Physical Access Gateway User Guide Release 1.1.0 and higher Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
CONTENTS Preface vii Obtaining Documentation and Submitting a Service Request Safety Warnings CHAPTER 1 Overview vii vii 1-1 System Overview 1-2 The Cisco Physical Access Gateway 1-2 Support for Multiple Cisco Physical Access Gateways Cisco Physical Access Manager 1-4 Optional Expansion Modules 1-5 Module Features 1-6 CAN Bus Connections for Optional Modules Installation and Configuration Summary Door Device Wiring Requirements 1-3 1-7 1-8 1-9 Understanding Supervised and Unsupervised Input De
Contents Entering the Gateway Network Settings 2-17 Changing the User Password 2-19 Upgrading the Gateway Firmware Using a Direct Connection Displaying Serial Numbers and Other Information 2-22 Configuring the Gateway Using the Cisco Physical Access Manager 2-20 2-23 Resetting the Cisco Physical Access Gateway 2-24 Soft Reset (Powercycle) 2-24 Hard Reset (Restore Factory Defaults) 2-24 CHAPTER 3 Connecting a Cisco Reader Module Overview 3-1 3-1 Package Contents 3-2 Physical Overview and Port Des
Contents APPENDIX A Environmental Specifications A-1 Environmental Specifications for the Cisco Physical Access Gateway Environmental Specifications for the Cisco Reader Module Environmental Specifications for the Cisco Input Module Environmental Specifications for the Cisco Output Module A-1 A-2 A-2 A-3 Cisco Physical Access Gateway User Guide OL-20932-02 v
Contents Cisco Physical Access Gateway User Guide vi OL-20932-02
Preface Obtaining Documentation and Submitting a Service Request For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at: http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.
Preface Cisco Physical Access Gateway User Guide viii OL-20932-02
CH A P T E R 1 Overview This document provides information to install and configure the components located near each door of a Cisco Physical Access Control system.
Chapter 1 Overview System Overview System Overview Cisco Physical Access Control is a comprehensive solution of hardware and software components, connected through an IP network as shown in Figure 1-1.
Chapter 1 Overview System Overview Related Documentation For installation and configuration instructions, see Chapter 2, “Installing and Configuring the Cisco Physical Access Gateway”. See the Cisco Physical Access Manager User Guide for advanced configuration and management of the access control components. Support for Multiple Cisco Physical Access Gateways A Cisco Physical Access Gateway is installed for each door, and connected to the IP network using an Ethernet connection, as shown in Figure 1-2.
Chapter 1 Overview System Overview Cisco Physical Access Manager The Cisco Physical Access Manager appliance (Cisco PAM) is a hardware and software solution that provides advanced configuration, monitoring, and report generation for the entire system. Each Cisco Physical Access Gateway is connected to the Cisco PAM appliance over an Ethernet-based IP network, as shown in Figure 1-2 on page 1-3.
Chapter 1 Overview Optional Expansion Modules The Cisco PAM appliance includes the following main features: • 1 RU appliance • Java thin client architecture • Policy support: two-door, anti-passback • Report generator (canned & custom) • Badge design & enrollment • Microsoft Active Directory integration • Fine grained user rights • Global I/O • Device pre-provisioning • Capacity & feature licenses • IT data integration • Warm standby high availability • Audit trails Related Docum
Chapter 1 Overview Optional Expansion Modules Module Features Figure 1-4 shows the modules for a Cisco Physical Access Control system. Figure 1-4 Cisco Physical Access Gateway and the Optional Modules Reader Module Input Module Output Module 187057 Cisco Physical Access Gateway Gateway Cisco Reader Module Cisco Input Module Cisco Output Module • Mandatory module. • • Connects up to two doors using the 10 pin Wiegand reader port, which can be configured as two five-pin ports.
Chapter 1 Overview Optional Expansion Modules CAN Bus Connections for Optional Modules The optional modules are connected to a Cisco Physical Access Gateway using a CAN bus connection, as shown in Figure 1-5. Figure 1-5 CAN Bus Wiring CAN+ Sheild CAN- Reader Module Input Module Output Module 271589 Gateway Module The CAN bus must adhere to the following rules: • The maximum length for the CAN bus is 1320 feet (400 Metres).
Chapter 1 Overview Installation and Configuration Summary Installation and Configuration Summary The following steps are an example of the main installation and configuration tasks for a Cisco Physical Access Control system. The exact procedure and order of installation for your system may vary. Step 1 Unpack and mount the Cisco Physical Access Gateway. Step 2 Unpack and mount optional reader, input or output modules, if necessary.
Chapter 1 Overview Door Device Wiring Requirements Door Device Wiring Requirements The wires used for an access control door depend on the devices installed at the door. Before installing the wiring for an access control system, do the following: • Determine the number and type of door devices used at each door (as shown in Figure 1-6). • Determine the number and type of wires used for each device, based on the descriptions in Table 1-2.
Chapter 1 Overview Understanding Supervised and Unsupervised Input Devices Table 1-2 Wires Used for Typical Door Devices (continued) Function Reader # of Wires 6 per reader Typical Wire Gauge Type Use 22 Wiegand A reader device includes the following: • 2 Wiegand data wires • 1 LED • 1 beeper • 2 power (12VDC) wires (500 feet maximum length) Electric strike or magnetic lock 2 18 Output Opens the locking device.
Chapter 1 Overview Understanding Supervised and Unsupervised Input Devices Figure 1-7 Example of a Supervised Door Sensor Cisco Physical Access Gateway User Guide OL-20932-02 1-11
Chapter 1 Overview Power Options and Requirements Power Options and Requirements This section includes the following information: • Power Options • Current Draw Requirements • Installing Surge Suppressors on Output Device Connections • Connect Reader Devices with Module Power Off Power Options Table 1-3 summarizes the power options for each module. The Cisco Physical Access Gateway supports Power over Ethernet (PoE) and DC power. All other modules support DC power only.
Chapter 1 Overview Power Options and Requirements Installing Surge Suppressors on Output Device Connections Install a surge suppressor between all output devices and the Gateway, Reader, or Output modules to protect the devices from power surges. Use one of the following methods: • If the base on a lock device receives power from an external power source, install an isolation relay between the output device and the Gateway, Reader, or Output module.
Chapter 1 Overview Mounting a Gateway or Optional Module Mounting a Gateway or Optional Module Each Cisco Physical Access Gateway and optional module includes two mounting brackets and four screws to mount the Gateway to the wall. Wall Mounting a Gateway or Optional Module Figure 1-9 shows the three options for attaching the included wall-mount brackets to a module.
Chapter 1 Overview Mounting a Gateway or Optional Module Wall Mount Installation Kit Contents Each module includes a wall mount installation kit that contains the following: Table 1-5 Wall Mount Installation Kit Contents Hardware Item Quantity Wall Mount brackets 2 Screws 8 Cisco Physical Access Gateway User Guide OL-20932-02 1-15
Chapter 1 Overview Mounting a Gateway or Optional Module Cisco Physical Access Gateway User Guide 1-16 OL-20932-02
CH A P T E R 2 Installing and Configuring the Cisco Physical Access Gateway Contents This chapter includes the following information: • Overview, page 2-2 • Package Contents, page 2-3 • Physical Overview and Port Description, page 2-3 • Installing the Cisco Physical Access Gateway, page 2-7 • Configuring and Managing the Gateway Using a Direct Connection, page 2-15 – Understanding Network Time Protocol (NTP) Settings, page 2-15 – Connecting a PC to the Gateway, page 2-16 – Entering the Gateway Ne
Chapter 2 Installing and Configuring the Cisco Physical Access Gateway Overview Overview The Cisco Physical Access Gateway (Figure 2-1) is installed near each door to provide access control and connections for card readers, door locks and other input and output devices. The Gateway is connected to the Cisco Physical Access Manager using an Ethernet connection to the IP network. Power is supplied through a Power over Ethernet (PoE) connection, or using a DC power source.
Chapter 2 Installing and Configuring the Cisco Physical Access Gateway Package Contents Package Contents Each Cisco Physical Access Gateway includes the following: • Six End-Of-Line (EOL) 1K termination resistors (used for supervised input interfaces) • Two mounting brackets, with 4 screws for each bracket • Regulatory compliance and safety information • Quick Start guide • Connector plugs, including the following: Type Quantity 10 Pin 1 3 Pin 4 2 Pin 6 Physical Overview and Port Descrip
Chapter 2 Installing and Configuring the Cisco Physical Access Gateway Physical Overview and Port Description Figure 2-3 Cisco Physical Access Gateway Ports and Connectors: Top View 2 5 6 7 8 9 10 4 3 2 187039 1 11 1 Power—Two-pin connector for Voltage In (VIN) and Ground (GND) to connect a 12 to 24 VDC external power source. 2 CAN—A three-wire CAN bus is used to connect additional modules, including the Cisco Reader Module, Cisco Input Module, and Cisco Output Module.
Chapter 2 Installing and Configuring the Cisco Physical Access Gateway Physical Overview and Port Description 7 8 Input interfaces—Three input interfaces used to sense the contact closure. Each input can be configured as supervised or unsupervised and can be configured to sense a Normally Open (NO) or Normally Closed (NC) contact. • An unsupervised input senses a simple contact closure state, including Normal or Alarm. When connected to open contacts, the terminal voltage range is 4V to 5V.
Chapter 2 Installing and Configuring the Cisco Physical Access Gateway Physical Overview and Port Description Table 2-1 Gateway LEDs (continued) Status Description Input Port LEDs OFF Input is not configured GREEN Input is configured and in normal state BLINKING GREEN Input is configured, and is receiving and alarm or other data.
Chapter 2 Installing and Configuring the Cisco Physical Access Gateway Installing the Cisco Physical Access Gateway Installing the Cisco Physical Access Gateway • Before You Begin, page 2-7 • Procedure, page 2-7 Before You Begin Before you install a Cisco Physical Access Gateway, verify the following: • Verify that the module has access to a power source. See the “Power Options and Requirements” section on page 1-12 for more information.
Chapter 2 Installing and Configuring the Cisco Physical Access Gateway Installing the Cisco Physical Access Gateway Power Connections for the Cisco Physical Access Gateway 271594 Figure 2-4 2 1 3 Step 3 1 DC power GND (ground)— Connects the DC ground wire to the Gateway. 2 DC power Voltage In (VIN)—Connects the DC Voltage In (VIN) wire to the Gateway. 3 ETH0 for PoE—Connects the Ethernet cable from the Access Layer switch to the Gateway. To use this power option, the switch must support PoE.
Chapter 2 Installing and Configuring the Cisco Physical Access Gateway Installing the Cisco Physical Access Gateway Figure 2-5 shows the location of the Wiegand interface connections. The table describes the connections for 10-pin and 5-pin reader interface connections. The wire connectors from the reader device are shown in parentheses. If attaching a second reader, use the alternative connections shown in the column on the far right.
Chapter 2 Installing and Configuring the Cisco Physical Access Gateway Installing the Cisco Physical Access Gateway Chassis Label One Reader Description 10 Wire Connection First Reader in a 5 Wire Connection Second Reader in a 5 Wire Connection 9 HCRD Hold Control HCRD (blue) ---------- D1/CLCK (white) 10 CP Card Present CP (purple) ---------- D0 (green) 1. Wire colors are shown in parentheses. 2. Outputs show the LED color and reader wire color (in parentheses).
Chapter 2 Installing and Configuring the Cisco Physical Access Gateway Installing the Cisco Physical Access Gateway Input Connections: Cisco Physical Access Gateway and Reader Module 271592 Figure 2-7 3 Step 5 4 1 2 1 2 1 2 1 Positive Input Connections—Positive connection to an Input device. 2 Ground Input Connections—Ground connection to an Input device. 3 TM—Tamper input: an unsupervised input that raises a “tamper” alarm when the circuit is open.
Chapter 2 Installing and Configuring the Cisco Physical Access Gateway Installing the Cisco Physical Access Gateway Output Connections: Cisco Physical Access Gateway and Reader Module 271593 Figure 2-8 1 Step 6 Note 2 3 1 1 Normally Open (N.O.) connection 2 C 2 3 1 3 2 3 Normally Closed (N.O.) connection Connect optional expansion modules to the Gateway, if necessary: a. Insert a three-pin connector plug into the CAN1 port, as shown in Figure 2-9. b.
Chapter 2 Installing and Configuring the Cisco Physical Access Gateway Installing the Cisco Physical Access Gateway CAN1 Connections: Cisco Physical Access Gateway and Reader Module 271590 Figure 2-9 1 1 2 3 CAN+ Connects to the positive terminal of the CAN bus. 2 CANConnects to the negative terminal of the CAN bus. 3 Shield Connects to GND and/or Shield.
Chapter 2 Installing and Configuring the Cisco Physical Access Gateway Installing the Cisco Physical Access Gateway Step 7 Connect the Gateway to the IP network by connecting an Ethernet cable to the ETH0 port, as shown in Figure 2-11. ETH 0 Ethernet Connection for the Cisco Physical Access Gateway 271591 Figure 2-11 1 1 Step 8 ETH0—Ethernet port for connecting the Gateway to the IP network. Note The ETH0 connection can also be used for Power over Ethernet.
Chapter 2 Installing and Configuring the Cisco Physical Access Gateway Configuring and Managing the Gateway Using a Direct Connection Configuring and Managing the Gateway Using a Direct Connection To enable the Gateway communication with the Cisco PAM appliance, connect a PC to the ETH1 port and use a web browser to enter basic network settings, as described in this section.
Chapter 2 Installing and Configuring the Cisco Physical Access Gateway Configuring and Managing the Gateway Using a Direct Connection Note Other systems that are integrated with Cisco PAM, such as the Video Surveillance Manager (Cisco VSM), should use the same NTP server setting. Connecting a PC to the Gateway To enter the initial Gateway settings or perform other administration tasks, connect a PC to the Gateway ETH1 port and use a web browser to access the administration pages.
Chapter 2 Installing and Configuring the Cisco Physical Access Gateway Configuring and Managing the Gateway Using a Direct Connection Figure 2-12 Login Screen for the Cisco Physical Access Gateway The web administration pages appear, and are described in the following sections. Entering the Gateway Network Settings Enter the network settings to enable IP communication between the Gateway and the Cisco PAM appliance.
Chapter 2 Installing and Configuring the Cisco Physical Access Gateway Configuring and Managing the Gateway Using a Direct Connection Figure 2-13 Network Settings for the Cisco Physical Access Gateway Step 2 (Optional) Enter the DNS Server address if names (not IP addresses) are used for the CPAM address. Step 3 Enter the Cisco PAM Configuration: a. Enter the Cisco PAM IP Address (IP address or name) to enable Gateway communication with the appliance. b.
Chapter 2 Installing and Configuring the Cisco Physical Access Gateway Configuring and Managing the Gateway Using a Direct Connection Step 6 Perform additional configuration, verification, and monitoring tasks as described in the Cisco Physical Access Manager User Guide. Changing the User Password Tip You can also change the password for one or more Gateways using the Cisco PAM desktop software.
Chapter 2 Installing and Configuring the Cisco Physical Access Gateway Configuring and Managing the Gateway Using a Direct Connection Upgrading the Gateway Firmware Using a Direct Connection Tip You can also upgrade the firmware for a single Gateway, or all Gateways, over the network using the Cisco PAM desktop software. For instructions, see the Cisco Physical Access Manager User Guide.
Chapter 2 Installing and Configuring the Cisco Physical Access Gateway Configuring and Managing the Gateway Using a Direct Connection Option 1: Local Disk To upload a firmware file from a local on the connected PC: a. Choose the Local radio button, as shown in Figure 2-15. b. Click the Browse button and choose a file from located on a local or network disk. The selected file appears in the Image Name field. You can also manually enter the directory path and filename.
Chapter 2 Installing and Configuring the Cisco Physical Access Gateway Configuring and Managing the Gateway Using a Direct Connection Displaying Serial Numbers and Other Information Use the Show Inventory window to display the module serial number and other information, such as the module serial number. Step 1 Log on to the Gateway administration tool, as described in the “Connecting a PC to the Gateway” section on page 2-16. Step 2 Click the Show Inventory tab, as shown in Figure 2-16.
Chapter 2 Installing and Configuring the Cisco Physical Access Gateway Configuring the Gateway Using the Cisco Physical Access Manager Configuring the Gateway Using the Cisco Physical Access Manager After the initial Gateway configuration is complete, use the The Cisco Physical Access Manager (Cisco PAM) desktop software for advanced configuration of Gateways and other components. For example, you can use Cisco PAM to configure doors, door devices and access policies enabled by the Gateway modules.
Chapter 2 Installing and Configuring the Cisco Physical Access Gateway Resetting the Cisco Physical Access Gateway Resetting the Cisco Physical Access Gateway Reset the Gateway to powercycle the module, restore the factory settings, or delete the stored logs and other data. The effect of the restart depends on the type of restart your perform, as described in the following sections.
CH A P T E R 3 Connecting a Cisco Reader Module Overview The optional Cisco Reader Module (Figure 3-1) is similar to the Cisco Physical Access Gateway, providing the same ports for Wiegand readers and other input and output devices. The Cisco Reader Module is attached to a Cisco Physical Access Gateway to provide additional connections for one or two doors, but does not include Ethernet connections for the IP network. Power is supplied using the 2-pin connector for 12 to 24 VDC external power.
Chapter 3 Connecting a Cisco Reader Module Package Contents The Cisco Reader Module is connected to a required Cisco Physical Access Gateway using a CAN connection, as shown in Figure 3-2.
Chapter 3 Connecting a Cisco Reader Module Physical Overview and Port Description Physical Overview and Port Description Each Cisco Reader Module includes ports for connecting up to two doors and associated input and output devices, as shown in Figure 3-3 and Figure 3-4.
Chapter 3 Connecting a Cisco Reader Module Physical Overview and Port Description Figure 3-4 Cisco Reader Module Ports and Connectors: Top View 2 5 6 7 8 9 10 3 2 1 187038 1 Power Two-pin connector for Voltage In (VIN) and Ground (GND) to connect a 12 to 24 VDC external power source. 2 CAN interfaces A 3-wire CAN bus is used to connect additional modules. Note 3 Modules are connected using the CAN1 interface. The CAN2 interface is not supported in this release.
Chapter 3 Connecting a Cisco Reader Module Physical Overview and Port Description 6 Input interfaces Three input interfaces used to sense the contact closure. Each input can be configured as supervised or unsupervised and can be configured to sense a Normally Open (NO) or Normally Closed (NC) contact. 7 • An unsupervised input senses a simple contact closure state, including Normal or Alarm. When connected to open contacts, the terminal voltage range is 4V to 5V.
Chapter 3 Connecting a Cisco Reader Module Installing the Cisco Reader Module Status LEDs Table 3-1 describes the Gateway module status LEDs: Table 3-1 Gateway LEDs Status Description Input Port LEDs OFF Input is not configured GREEN Input is configured and in normal state BLINKING GREEN Input is configured, and is receiving and alarm or other data.
Chapter 3 Connecting a Cisco Reader Module Installing the Cisco Reader Module See the “Power Options and Requirements” section on page 1-12 for more information. Power Connection: for the Cisco Reader Module 271601 Figure 3-5 2 1 1 DC power GND (ground) Connects the DC ground wire to the module. 2 DC power Voltage In (VIN) Connects the DC Voltage In (VIN) wire to the module. Step 3 Connect the module to the Gateway using a CAN bus: a.
Chapter 3 Connecting a Cisco Reader Module Installing the Cisco Reader Module CAN1 Connections: Cisco Physical Access Gateway and Reader Module 271600 Figure 3-6 1 2 3 4 1 CAN+ Connects to the positive terminal of the CAN bus. 2 CANConnects to the negative terminal of the CAN bus. 3 Shield Connects to GND and/or Shield. 3 CAN Terminator Turn the terminator ON if the device is the last device in a CAN wiring bus.
Chapter 3 Connecting a Cisco Reader Module Installing the Cisco Reader Module Step 4 Connect one or two door reader devices to the Wiegand interface using one of the following configurations: • Connect a single door reader using all 10 Wiegand interface pins. • Connect one or two door readers using 5-pin Wiegand interface connections (for installations where a 5-pin interface is sufficient). Figure 3-8 shows the location of the Wiegand interface connections.
Chapter 3 Connecting a Cisco Reader Module Installing the Cisco Reader Module Chassis Label One Reader Description 10 Wire Connection First Reader in a 5 Wire Connection Second Reader in a 5 Wire Connection RED Output RED (brown) ---------- 3 GRN (orange) BPR Output (Beeper) BPR (yellow) ---------- ---------- HCRD Hold Control HCRD (blue) ---------- D1/CLCK (white) CP Card Present CP (purple) ---------- D0 (green) 1. Wire colors are shown in parentheses. 2.
Chapter 3 Connecting a Cisco Reader Module Installing the Cisco Reader Module Input Connections: Cisco Physical Access Gateway and Reader Module 271592 Figure 3-10 3 1 4 1 2 1 2 1 2 Positive Input Connections Positive connection to an Input device. 2 Ground Input Connections Ground connection to an Input device. 3 TM Tamper input: an unsupervised input that raises a “tamper” alarm when the circuit is open. Can be configured as a general input device using the Cisco Physical Access Manager.
Chapter 3 Connecting a Cisco Reader Module Installing the Cisco Reader Module – If the relay is normally open, use the C & NO connections. The circuit is closed when triggered. – If the relay is normally closed, use the C & NC connections. The circuit is opened when triggered. Output Connections: Cisco Physical Access Gateway and Reader Module 271593 Figure 3-11 1 Step 7 2 3 1 1 Normally Open (N.O.) connection 2 C (Common) 2 3 1 3 2 3 Normally Closed (N.O.
CH A P T E R 4 Connecting a Cisco Input Module Overview The optional Cisco Input Module (Figure 4-1) is attached to a Cisco Physical Access Gateway or Cisco Reader Module to provide additional connections for up to ten input devices. Each connection can be configured as supervised or unsupervised. A supervised connection is a four- state connection to determine if the connection is (1) short (2) is open (3)normal state or (4) alarm state. An unsupervised input indicates only normal or alarm.
Chapter 4 Connecting a Cisco Input Module Package Contents The optional Cisco Input Module is connected to a Cisco Physical Access Gateway or Cisco Reader Module using a CAN connection to provide connections for additional input devices, as, as shown in Figure 4-2.
Chapter 4 Connecting a Cisco Input Module Physical Overview and Port Description • Connector plugs: Type Quantity 3 Pin 1 2 Pin 13 Physical Overview and Port Description Each Cisco Input Module includes 10 ports for connecting additional input devices. as shown in Figure 4-3.
Chapter 4 Connecting a Cisco Input Module Physical Overview and Port Description Figure 4-4 Cisco Input Module Ports and Connectors: Top View 4 5 6 3 2 1 187039 1 Power Two-pin connector for Voltage In (VIN) and Ground (GND) to connect a 12 to 24 VDC external power source. 2 CAN interface A 3-wire CAN bus is used to connect additional modules. Note 3 Modules are connected using the CAN1 interface. The CAN2 interface is not supported in this release.
Chapter 4 Connecting a Cisco Input Module Installing the Cisco Input Module 8 PF Power fail input: an unsupervised input that raises a “power fail” alarm when the circuit is open. Can be configured as an additional unsupervised port. The corresponding LED is red when circuit is open (when no input is connected). 9 TM Tamper input: an unsupervised input that raises a “tamper” alarm when the circuit is open. Can be configured as an additional unsupervised port.
Chapter 4 Connecting a Cisco Input Module Installing the Cisco Input Module Power Connections for the Input and Output Modules 271599 Figure 4-5 1 2 1 DC power GND (ground) Connects the DC ground wire to the module. 2 DC power Voltage In (VIN) Connects the DC Voltage In (VIN) wire to the module. Step 3 Connect the module to the CAN bus: a. Insert a three-pin connector plug into the CAN1 port, as shown in Figure 4-6. b. Connect the CAN wires to the CAN bus, as shown in Figure 4-7 c.
Chapter 4 Connecting a Cisco Input Module Installing the Cisco Input Module CAN Connections: Input and Output Modules 271598 Figure 4-6 1 2 3 4 1 CAN+ Connects to the positive terminal of the CAN bus. 2 CANConnects to the negative terminal of the CAN bus. 3 Shield Connects to GND and/or Shield. 3 CAN Terminator Turn the terminator ON if the device is the last device in a CAN wiring bus.
Chapter 4 Connecting a Cisco Input Module Installing the Cisco Input Module (Optional, for supervised input connections only). Install two End-Of-Line (EOL) 1K termination resistors in each supervised input interface (one terminator in each connector). Figure 4-8 shows the terminator installation for a Normally Closed (NC) and Normally Open (NO) input connection. Figure 4-8 Input Connections: Cisco Physical Access Gateway and Reader Module 1K,, 1% 1K,, 1% 1K,, 1% 1K,, 1% c.
CH A P T E R 5 Connecting a Cisco Output Module Overview The optional Cisco Output Module (Figure 5-1) is attached to a Cisco Physical Access Gateway or Cisco Reader Module to provide additional connections for up to 8 outputs, each of which can be configured as Normally Open (NO) or Normally Closed (NC).
Chapter 5 Connecting a Cisco Output Module Package Contents The Cisco Output Module is connected to a Cisco Physical Access Gateway or Cisco Reader Module using a CAN connection to provide connections for additional output devices, as, as shown in Figure 5-2.
Chapter 5 Connecting a Cisco Output Module Physical Overview and Port Description Physical Overview and Port Description Each Cisco Output Module includes 10 ports for connecting additional output devices. as shown in Figure 5-3 and Figure 5-4.
Chapter 5 Connecting a Cisco Output Module Physical Overview and Port Description Figure 5-4 Cisco Output Module Ports and Connectors: Top View 4 5 6 3 2 1 187045 1 Power Two-pin connector for Voltage In (VIN) and Ground (GND) to connect a 12 to 24 VDC external power source. 2 CAN interface A 3-wire CAN bus is used to connect additional modules. Note 3 Modules are connected using the CAN1 interface. The CAN2 interface is not supported in this release.
Chapter 5 Connecting a Cisco Output Module Physical Overview and Port Description 4 Output Interfaces Eight Form C (5A @ 30V) relay outputs. Each output can be configured as either Normally Closed (NC) or Normally Open (NO). • C & NO connection: The relay is normally open. The circuit is closed when triggered. • C & NC connection: The relay is normally closed. The circuit is opened when triggered.
Chapter 5 Connecting a Cisco Output Module Installing the Cisco Output Module Installing the Cisco Output Module Install a Cisco Output Module is provide additional output connections for a Cisco Reader Module or Gateway Before You Begin Verify the following: • Verify that the module has access to a power source. See the “Power Options and Requirements” section on page 1-12 for more information. • Verify that you have the necessary mounting brackets or other hardware.
Chapter 5 Connecting a Cisco Output Module Installing the Cisco Output Module Power Connections for the Cisco Output Module 271599 Figure 5-5 1 2 1 DC power GND (ground) Connects the DC ground wire to the module. 2 DC power Voltage In (VIN) Connects the DC Voltage In (VIN) wire to the module. Step 3 Connect the module to the CAN bus: a. Insert a three-pin connector plug into the CAN1 port, as shown in Figure 5-6. b. Connect the CAN wires to the CAN bus, as shown in Figure 5-7 c.
Chapter 5 Connecting a Cisco Output Module Installing the Cisco Output Module CAN Connections: Input and Output Modules 271598 Figure 5-6 1 2 3 4 1 CAN+ Connects to the positive terminal of the CAN bus. 2 CANConnects to the negative terminal of the CAN bus. 3 Shield Connects to GND and/or Shield. 3 CAN Terminator Turn the terminator ON if the device is the last device in a CAN wiring bus.
Chapter 5 Connecting a Cisco Output Module Installing the Cisco Output Module – If the relay is normally open, use the C & NO connections. The circuit is closed when triggered. – If the relay is normally closed, use the C & NC connections. The circuit is opened when triggered. Step 5 See the Cisco Physical Access Manager User Guide for information to configure the module ports.
Chapter 5 Connecting a Cisco Output Module Installing the Cisco Output Module Cisco Physical Access Gateway User Guide 5-10 OL-20932-02
A P P E N D I X 6 Safety Warnings Before you install the device, observe the safety warnings in this section. • Statement 1071—Warning Definition, page 6-1 • Statement 369—Power over Ethernet (PoE) IEEE 802.3af, page 6-6 • Statement 353—This Product Must be Connected, page 6-7 • Statement 1040—Product Disposal, page 6-9 • Statement 1004—Installation Instructions, page 6-10 Statement 1071—Warning Definition Warning IMPORTANT SAFETY INSTRUCTIONS This warning symbol means danger.
Appendix 6 Varoitus Safety Warnings TÄRKEITÄ TURVALLISUUSOHJEITA Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien lausuntonumeroiden avulla.
Appendix 6 Safety Warnings Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de prevenção de acidentes.
Appendix 6 Aviso Safety Warnings INSTRUÇÕES IMPORTANTES DE SEGURANÇA Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo.
Appendix 6 Safety Warnings Cisco Physical Access Gateway User Guide OL-20932-02 6-5
Appendix 6 Safety Warnings Statement 369—Power over Ethernet (PoE) IEEE 802.3af Warning Waarschuwing This product must be connected to a Power over Ethernet (PoE) IEEE 802.3af compliant power source. Statement 369 Dit product moet worden verbonden met een stroomvoorziening die compatibel is met PoE (power-over-ethernet) IEEE 802.3af.
Appendix 6 Safety Warnings Varoitus Tämä tuote on liitettävä PoE (power-over-ethernet) IEEE 802.3af -yhteensopivaan virtalähteeseen. Attention Ce produit doit être connecté à une source d'alimentation électrique par câble Ethernet (PoE) conforme à la norme IEEE 802.3af. Warnung Dieses Produkt muss an eine Stromquelle angeschlossen sein, die mit dem IEEE 802.3af-Standard Power-over-Ethernet (PoE) kompatibel ist.
Appendix 6 Safety Warnings Attention Ce produit doit être connecté à une source d'alimentation électrique par câble Ethernet (PoE) conforme à la norme IEEE 802.3af ou à une source d'alimentation limitée conforme à la norme IEC60950. Warnung Dieses Produkt muss entweder an eine Stromquelle angeschlossen sein, die mit dem IEEE 802.3af-Standard Power-over-Ethernet (PoE) kompatibel ist oder an eine Stromquelle für geringe Leistungen, die IEC60950-kompatibel ist.
Appendix 6 Safety Warnings Statement 1040—Product Disposal Warning Waarschuwing Varoitus Ultimate disposal of this product should be handled according to all national laws and regulations. Statement 1040 Het uiteindelijke wegruimen van dit product dient te geschieden in overeenstemming met alle nationale wetten en reglementen. Tämä tuote on hävitettävä kansallisten lakien ja määräysten mukaisesti.
Appendix 6 Safety Warnings Statement 1004—Installation Instructions Warning Waarschuwing Varoitus Read the installation instructions before connecting the system to the power source. Statement 1004 Raadpleeg de installatie-instructies voordat u het systeem op de voedingsbron aansluit. Lue asennusohjeet ennen järjestelmän yhdistämistä virtalähteeseen. Attention Avant de brancher le système sur la source d'alimentation, consulter les directives d'installation.
Appendix 6 Safety Warnings Advarsel Aviso ¡Advertencia! Varning! Les installasjonsinstruksjonene før systemet kobles til strømkilden. Leia as instruções de instalação antes de ligar o sistema à fonte de energia. Lea las instrucciones de instalación antes de conectar el sistema a la red de alimentación. Läs installationsanvisningarna innan du kopplar systemet till strömförsörjningsenheten.
Appendix 6 Safety Warnings Cisco Physical Access Gateway User Guide 6-12 OL-20932-02
A P P E N D I X A Environmental Specifications This appendix contains the following: • Environmental Specifications for the Cisco Physical Access Gateway, page A-1 • Environmental Specifications for the Cisco Reader Module, page A-2 • Environmental Specifications for the Cisco Input Module, page A-2 • Environmental Specifications for the Cisco Output Module, page A-3 Environmental Specifications for the Cisco Physical Access Gateway Table A-1 describes the environmental specifications for the Cisc
Appendix A Environmental Specifications Environmental Specifications for the Cisco Reader Module Table A-1 Specifications for the Cisco Physical Access Gateway Humidity 5 to 95% relative, non-condensing Power There are two options to power the device: • 12 to 24 VDC (+/- 10%) through an external power supply • 802.
Appendix A Environmental Specifications Environmental Specifications for the Cisco Output Module Table A-3 Weight Specifications for the Cisco Input Module. Without Plugs & Brackets: 1.24 lb (562 g) With Plugs: 1.34 lb (630 g) With Brackets: 1.4 lb (636 g) With Plugs & Brackets: 1.
Appendix A Environmental Specifications Environmental Specifications for the Cisco Output Module Cisco Physical Access Gateway User Guide A-4 OL-20932-02
