Installation and Operation Manual IPmux-1, IPmux-1E TDMoIP Gateways
IPmux-1, IPmux-1E TDMoIP Gateways Installation and Operation Manual Notice This manual contains information that is proprietary to RAD Data Communications Ltd. ("RAD"). No part of this publication may be reproduced in any form whatsoever without prior written approval by RAD Data Communications.
Limited Warranty RAD warrants to DISTRIBUTOR that the hardware in the IPmux-1, IPmux-1E to be delivered hereunder shall be free of defects in material and workmanship under normal use and service for a period of twelve (12) months following the date of shipment to DISTRIBUTOR.
General Safety Instructions The following instructions serve as a general guide for the safe installation and operation of telecommunications products. Additional instructions, if applicable, are included inside the manual. Safety Symbols Warning This symbol may appear on the equipment or in the text. It indicates potential safety hazards regarding product operation or maintenance to operator or service personnel.
Handling Energized Products General Safety Practices Do not touch or tamper with the power supply when the power cord is connected. Line voltages may be present inside certain products even when the power switch (if installed) is in the OFF position or a fuse is blown. For DC-powered products, although the voltages levels are usually not hazardous, energy hazards may still exist.
Connection of Data and Telecommunications Cables Data and telecommunication interfaces are classified according to their safety status. The following table lists the status of several standard interfaces. If the status of a given port differs from the standard one, a notice will be given in the manual. Ports Safety Status V.11, V.28, V.35, V.36, RS-530, X.
Caution Attention To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cords. Pour réduire les risques s’incendie, utiliser seulement des conducteurs de télécommunications 26 AWG ou de section supérieure. Some ports are suitable for connection to intra-building or non-exposed wiring or cabling only. In such cases, a notice will be given in the installation instructions. Do not attempt to tamper with any carrier-provided equipment or connection hardware.
Canadian Emission Requirements This Class A digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment Regulation. Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. Warning per EN 55022 (CISPR-22) Warning This is a class A product. In a domestic environment, this product may cause radio interference, in which case the user will be required to take adequate measures.
Declaration of Conformity Manufacturer's Name: RAD Data Communications Ltd. Manufacturer's Address: 24 Raoul Wallenberg St. Tel Aviv 69719 Israel declares that the product: IPmux-1, IPmux-1E Product Name: conforms to the following standard(s) or other normative document(s): EMC: Safety: EN 55022 (1994) Limits and methods of measurement of radio disturbance characteristics of information technology equipment.
Preface Foreword This manual describes the technical characteristics, applications, installation and operation of IPmux-1 and IPmux-1E. In this manual the products will be referred to as IPmux-1/1E. Manual Organization This manual is organized as follows: Chapter 1. Introduction presents the main features versions, applications, functional description, and lists the technical specifications of IPmux-1/1E. Chapter 2. Installation provides detailed installation and operation instructions for IPmux-1/1E.
Conventions Note A note draws attention to a general rule for a procedure, or to exceptions to a rule. Caution A caution warns of possible damage to the equipment if a procedure is not followed correctly. Warning A warning alerts to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the equipment. If these instructions are not followed exactly, possible bodily injury may occur.
IPmux-1, IPmux-1E TDMoIP Gateways Installation and Operation Manual Notice This manual contains information that is proprietary to RAD Data Communications Ltd. ("RAD"). No part of this publication may be reproduced in any form whatsoever without prior written approval by RAD Data Communications.
Limited Warranty RAD warrants to DISTRIBUTOR that the hardware in the IPmux-1, IPmux-1E to be delivered hereunder shall be free of defects in material and workmanship under normal use and service for a period of twelve (12) months following the date of shipment to DISTRIBUTOR.
General Safety Instructions The following instructions serve as a general guide for the safe installation and operation of telecommunications products. Additional instructions, if applicable, are included inside the manual. Safety Symbols Warning This symbol may appear on the equipment or in the text. It indicates potential safety hazards regarding product operation or maintenance to operator or service personnel.
Handling Energized Products General Safety Practices Do not touch or tamper with the power supply when the power cord is connected. Line voltages may be present inside certain products even when the power switch (if installed) is in the OFF position or a fuse is blown. For DC-powered products, although the voltages levels are usually not hazardous, energy hazards may still exist.
Connection of Data and Telecommunications Cables Data and telecommunication interfaces are classified according to their safety status. The following table lists the status of several standard interfaces. If the status of a given port differs from the standard one, a notice will be given in the manual. Ports Safety Status V.11, V.28, V.35, V.36, RS-530, X.
Caution Attention To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cords. Pour réduire les risques s’incendie, utiliser seulement des conducteurs de télécommunications 26 AWG ou de section supérieure. Some ports are suitable for connection to intra-building or non-exposed wiring or cabling only. In such cases, a notice will be given in the installation instructions. Do not attempt to tamper with any carrier-provided equipment or connection hardware.
Canadian Emission Requirements This Class A digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment Regulation. Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. Warning per EN 55022 (CISPR-22) Warning This is a class A product. In a domestic environment, this product may cause radio interference, in which case the user will be required to take adequate measures.
Declaration of Conformity Manufacturer's Name: RAD Data Communications Ltd. Manufacturer's Address: 24 Raoul Wallenberg St. Tel Aviv 69719 Israel declares that the product: IPmux-1, IPmux-1E Product Name: conforms to the following standard(s) or other normative document(s): EMC: Safety: EN 55022 (1994) Limits and methods of measurement of radio disturbance characteristics of information technology equipment.
Preface Foreword This manual describes the technical characteristics, applications, installation and operation of IPmux-1 and IPmux-1E. In this manual the products will be referred to as IPmux-1/1E. Manual Organization This manual is organized as follows: Chapter 1. Introduction presents the main features versions, applications, functional description, and lists the technical specifications of IPmux-1/1E. Chapter 2. Installation provides detailed installation and operation instructions for IPmux-1/1E.
Conventions Note A note draws attention to a general rule for a procedure, or to exceptions to a rule. Caution A caution warns of possible damage to the equipment if a procedure is not followed correctly. Warning A warning alerts to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the equipment. If these instructions are not followed exactly, possible bodily injury may occur.
Quick Start Guide 1. Setting Jumpers - IPmux-1E ISDN Version Only The IPmux-1E ISDN version contains jumpers for Phantom Feed. Other IPmux-1/1E models do not require jumper configuration. To set the IPmux-1E ISDN-S module jumpers: If necessary, change the settings in accordance with the specific requirements of your application: • ENA – enable Phantom Feed • DIS – disable Phantom Feed. The Phantom Feed ENA/DIS setting influences the IPmux-1E BRI operation mode.
IPmux-1/1E Installation and Operation Manual Quick Start Guide 3. IPmux-1/1E Configuration General IPmux-1/1E configuration is performed from the ASCII terminal connected to the Control port. The system software is divided into three functions: Note • System: General IPmux-1/1E system information. • Configuration: Performs all configuration functions • Performance Monitoring: Monitors overall performance Perform the following configuration procedures in the order given. Configuration 1.
Contents Chapter 1. Introduction 1.1 Overview..................................................................................................................... 1-1 Versions................................................................................................................................ 1-1 Applications.......................................................................................................................... 1-2 Features.........................................................
Table of Contents 3.4 Overview of Menu Operations .................................................................................... 3-6 Navigating ............................................................................................................................ 3-6 Main Menu......................................................................................................................... 3-12 System Menu.....................................................................................
Table of Contents 1-14. 1-15. 1-16. 1-17. 1-18. IPmux-1E in Adaptive Timing Mode .................................................................................. 1-15 TDMoIP Frame Structure................................................................................................... 1-16 VLAN Tag Format (802.1p&q) ........................................................................................... 1-18 Packet Delay Variation ...................................................................
Table of Contents List of Tables 1-1. Fiber Options ........................................................................................................................ 1-7 1-2. Ethernet Frame Structure..................................................................................................... 1-17 1-3. UDP Ports Definition........................................................................................................... 1-18 1-4.
Chapter 1 Introduction 1.1 Overview IPmux-1 and IPmux-1E (referred to as IPmux-1/1E) offer a solution for extending traditional E1/T1, ISDN, or POTS TDM services transparently over Packet Switched Networks (PSNs) such as IP, Ethernet, and MPLS networks. The device converts the data stream coming from its user ports into configurable sized IP packets that are extended over the Fast Ethernet Network port, and vice versa. IPmux-1/1E offers end-to-end synchronization for voice/leased line applications.
IPmux-1/1E Installation and Operation Manual Chapter 1 Introduction • IPmux-1E with E1 interface and an echo canceller Balanced line with an RJ-45 connector Unbalanced line with a mini-coaxial connector (TBNC) • IPmux-1E with T1 interface and an echo canceller Balanced line with an RJ-45 connector Unbalanced line with a mini-coaxial connector (TBNC). An external clock port is optional for IPmux-1/1E (Ordering options). A user Ethernet interface is optional for IPmux-1/1E (Ordering options).
IPmux-1/1E Installation and Operation Manual Chapter 1 Introduction 100 Mbps n × E1/T1 PSTN IPmux-8/16 Ethernet Switch 1 Gbps 1 Gbps IP/Ethernet Network E1/T1 100 Mbps Fiber IPmux-1 Ethernet Switch 10/100 Mbps E1/T1 IPmux-1 Figure 1-2.
IPmux-1/1E Installation and Operation Manual Chapter 1 Introduction ISDN U Ports or V5.1 ISDN Telephones Telephone Switch Megaplex ISDN Telephones Ethernet Switch IPmux-1E IP/Ethernet Network IPmux-1E Computer Workstation Figure 1-4. Digital ISDN Application (V5.1 Concentration of Remote BRIs) ISDN Telephones ISDN S TE NT IP/Ethernet Network PBX IPmux-1E Computer Workstation IPmux-1E Computer Workstation Figure 1-5.
IPmux-1/1E Installation and Operation Manual Chapter 1 Introduction E1/T1 IPmux-1 FXS IPmux-1E BRI BRI Grooming Internet IPmux-1E Megaplex E1 CAS Analog Telephone Grooming Switch Switch Ethernet Switch IP Network Ethernet Switch Figure 1-6. Ethernet-based Multi-tenant Application with Voice and Data Integrated Access Features Management IPmux-1/1E can be managed locally by connecting an ASCII terminal to the RS-232 port on the front panel, or via Telnet or SNMP.
IPmux-1/1E Installation and Operation Manual Chapter 1 Introduction ISDN BRI IPmux-1E has 4-ports, S-interface only. Each port can be configured as either NT or TE (Network/User) by jumper and software; NT or TE is configured per device. IPmux-1E can be configured to 1, 2, 3 or 4 active ports. IPmux-1E works in transparent mode (no termination/compression of the BRI “D” channels). It operates opposite a Megaplex unit, as a concentrator in transparent mode, or opposite another IPmux-1E with ISDN BRI ports.
IPmux-1/1E Installation and Operation Manual Chapter 1 Introduction Table 1-1. Fiber Options Interface Type Wavelength (nm) Optical Power (dBm) Min Max Receive Sensitivity (dBm) Optical Budget (dB)* Loss (dB/km) Min Max SC Multimode 1300 -20 -14 -31 8* 1 4 SC Single mode 1300 -20 -14 -31 8* 0.5 0.8 LC Multimode 1300 -19 -14 -32 10* 1 4 LC Single mode 1300 -15 -8 -32 14* 0.5 0.
IPmux-1/1E Installation and Operation Manual Chapter 1 Introduction QoS QoS supports: • Labeling IP level priority (ToS/Diffserv) for TDMoIP packets • VLAN tagging and priority labeling according to IEEE 802.1p&q for TDMoIP packets. The user can configure the ToS (Type of Service) of the outgoing TDMoIP packets. This allows an en-route Layer 3 router or switch, which supports ToS, to give higher priority to IPmux-1/1E TDMoIP traffic for delay-sensitive and secure applications.
IPmux-1/1E Installation and Operation Manual Chapter 1 Introduction Figure 1-7. IPmux-1/1E 3-Dimensional View Front Panel The control interface and indicator LEDs are located on the front panel of IPmux-1/1E. For further details see Front Panel Controls, Connectors, and Indicators in Chapter 3. Rear Panel User and network ports and power supply are located on the rear panel of IPmux-1/1E. For further details see Chapter 2. 1.
IPmux-1/1E Installation and Operation Manual Chapter 1 Introduction IPmux-1/1E works in conjunction with the rest of the IPmux product line (see Figure 1-9). The combination of IPmux products provides up to 31 per E1 or 24 per T1 remote bundles, attached to one central IPmux-4/16 (see Figure 1-9). E1/T1 Megaplex E1/T1 Line 2 Line 4 E1/T1 IPmux-8/16 Line 1 Line 3 IPmux-8/16 IP over Ethernet E1/T1 IPmux-1E E1/T1 IPmux-1 Figure 1-9.
IPmux-1/1E Installation and Operation Manual Chapter 1 Introduction E1/T1 This section describes the IPmux-1 E1/T1 operation modes, which are: • Unframed – valid for static and CESoIP/E1 • Fractional – valid only for static and CESoIP • Fractional with CAS –valid only for static and dynamic CAS . Unframed (Transparent) In the transparent mode, the incoming bit stream from each channel (regardless of framing) is converted into IP over Ethernet frames.
IPmux-1/1E Installation and Operation Manual Chapter 1 Introduction Note If the jumpers enable phantom feeding, the TE mode cannot be selected as the IPmux-1E operation mode. If phantom feeding is disabled, both NT and TE are valid options. FXS/FXO/E&M The section describes the FXS/FXO/E&M operation modes, which are: • E1 mode • T1-D4 mode • T1 ESF mode. The IPmux-1E FXS/FXO/E&M operation modes allow IPmux to work opposite E1, T1-D4, or T1-ESF.
IPmux-1/1E Installation and Operation Manual Chapter 1 Introduction FXS/FXO/E&M The TS assignment in a bundle with analog (FXS/FXO/E&M) is straightforward. Each timeslot in a bundle is assigned to a specific analog channel according to analog channel numbers; the first timeslot is assigned to the lowest analog channel that is configured, etc. Note The E1/T1 TDMoIP gateway that works opposite the analog channels should work in Framed with CAS mode.
IPmux-1/1E Installation and Operation Manual Chapter 1 Introduction ISDN/FXS/FXO/E&M The available timing modes for the PCM clock are: • Loopback Timing – available only when IPmux-1E ISDN BRI is configured as TE (not available in ISDN BRI NT mode or for FXS/FXO/E&M interface). In this mode the PCM clock is derived from Channel 1. It is recommended not to deactivate Channel 1 while it is in loopback clock so that data will not be damaged.
IPmux-1/1E Installation and Operation Manual Chapter 1 Introduction Clock from External Distribution Network E1/T1 Device E1/T1 Device E1/T1 IP/Ethernet IPmux-1 IPmux-1 External Clock Mode External Clock Mode LBT Mode E1/T1 LBT Mode Figure 1-12.
IPmux-1/1E Installation and Operation Manual Chapter 1 Introduction Frame Format The Ethernet frame sent by the IPmux-1 is a UDP datagram that transfers E1/T1 payload bytes over IP over Ethernet (UDP payload + UDP header + IP header + Ethernet header). The UDP payload size depends on the connection mode: • Static mode: The UDP payload size is equal to TDM bytes per frame (TDM bytes/frame configuration).
IPmux-1/1E Installation and Operation Manual Chapter 1 Introduction Table 1-2.
IPmux-1/1E Installation and Operation Manual Chapter 1 Introduction VLAN Support VLAN, according to IEEE 802.1p&q, adds four bytes to the MAC layer of the Ethernet frame. The user can set the contents of these bytes, MAC layer priority and VLAN ID. In this mode, only VLAN format frames are sent and received by IPmux-1. Figure 1-16 shows the VLAN tag format. 00 8 802.1D Tag Protocol Type 6 VID CFI = 0 user_priority 81 5 4 1 Priority 8 1 VLAN ID Figure 1-16. VLAN Tag Format (802.
IPmux-1/1E Installation and Operation Manual Chapter 1 Introduction Packets Leaving IPmux-1 t Packets Arriving t PDV Figure 1-17. Packet Delay Variation PDVT (Jitter) Buffer IPmux-1 is equipped with a Packet DVT (Delay Variation Tolerance) buffer. The PDVT buffer or jitter buffer is filled by the incoming IP packets and emptied out to fill the TDM stream. The buffer begins to empty out only after it is half full in order to compensate for packet starvation from the Ethernet side.
Chapter 1 Introduction IPmux-1/1E Installation and Operation Manual Intrinsic PDV in Dynamic CAS Mode I.PDV (ms) = active time slot bytes in frame X 0.125 Active time slot bytes in frame is the number of bytes per active time slot that will be sent on every frame transmitted over the Ethernet. Intrinsic PDV in CESoIP Mode The value of the packet delay configuration is user-defined.
IPmux-1/1E Installation and Operation Manual Frame/second = Unframed: Chapter 1 Introduction 5447/n for a full E1 4107/n for a full T1 Framed: 8000 x k/(46.
IPmux-1/1E Installation and Operation Manual Chapter 1 Introduction The maximum Ethernet throughput in dynamic CAS mode is calculated by: [( Note 8000 payload ) x ((payload+ 4) x TS) + 4 + frame overhead] x 8 bits • where frame overhead is 46 bytes, including MAC, LLC, IP, and UFP layers • where TS = number of configured time slots • where payload = number of active time slot bytes per frame (24 to 64) The frame overhead does not include: • Preamble field: 7 bytes • SFD field: 1 byte • Interfram
IPmux-1/1E Installation and Operation Manual Chapter 1 Introduction Round Trip Delay in Static Mode (±2 µs) RTDelay(µs) = 2 x [ 47x n x 125 µs + PDVT buffer µs +1000 µs] + network round trip delay NTS TDM bytes/frame • where n = • where NTS = number of timeslots assigned; in unframed mode NTS is constant: 32 for E1, 24 for T1 48 Round Trip Delay in Dynamic CAS Mode RTDelay(µs) = 2 x [ • 8000000 payload + PDVT buffer µs +1000 µs] + network round trip delay where payload = number of active time
IPmux-1/1E Installation and Operation Manual Chapter 1 Introduction Duplicated Frames When frames are duplicated, IPmux-1/1E only uses the later frame. Dynamic CAS Mode Reordering and duplication of frames is not supported; the frames pass to the TDM side without any modification. CESoIP Mode The number of frames that are reordered depends on the frame delay and the jitter buffer size.
IPmux-1/1E Installation and Operation Manual Chapter 1 Introduction VLAN Traffic Behavior Table 1-4 lists the IP and VLAN validity checks that are performed with each Ethernet packet that is received by IPmux1/1E. Table 1-4.
IPmux-1/1E Installation and Operation Manual Chapter 1 Introduction Ethernet User Port The Ethernet user port allows a user to aggregate both TDMoIP traffic and his private network LAN traffic to a single Ethernet network connection without requiring an access switch. This is a cost effective solution for MTU or small office applications. A rate limiter to restrict user port traffic is supported.
IPmux-1/1E Installation and Operation Manual Note Chapter 1 Introduction Access to the IPmux host for management is possible only from the network port. Switch Behavior Use Table 1-6 to determine the operation mode. Table 1-6.
IPmux-1/1E Installation and Operation Manual Chapter 1 Introduction User Tagged Mode Features: • Network port learning is based on MAC+VLAN • User port learning is based on MAC+VLAN • TDMoIP & Managers traffic must be tagged. Table 1-8.
IPmux-1/1E Installation and Operation Manual Chapter 1 Introduction User Untagged Mode Features: • Network port learning is based on MAC+VLAN • User port learning is based on MAC+VLAN • TDMoIP & Managers traffic must be tagged. Table 1-9.
IPmux-1/1E Installation and Operation Manual Chapter 1 Introduction Rate Mode Features: • There is no Network port learning • User port learning is based on MAC • TDMoIP & Managers traffic are tagged or untagged. Table 1-10.
IPmux-1/1E Installation and Operation Manual Chapter 1 Introduction Rate + User Tagged Mode Features: • No Network port learning • User port learning is based on MAC • TDMoIP & Managers traffic must be tagged. Table 1-11.
IPmux-1/1E Installation and Operation Manual Chapter 1 Introduction Table 1-12.
IPmux-1/1E Installation and Operation Manual Chapter 1 Introduction Manager Option The server may send IPmux-1/1E a Manager configuration via the DHCP option field: • Manager IP - Option 200 (type IP Address) • VLAN ID - Option 201 (type long) • VLAN Priority - Option 202 (type byte). When IPmux-1/1E requests a Manager configuration from the server, there may be many replies. The device accepts the offer that includes a Manager Option.
IPmux-1/1E Installation and Operation Manual Chapter 1 Introduction T1 Port T1 Framing Local Terminal and Control Interface Ethernet Compliance ANSI T1.403, ITU-T Rec. G.703, G.704 Connector RJ-45, 8-pin Data Rate 1.544 Mbps Line Code B8ZS, B7ZS, AMI Line Impedance Balanced: 100Ω Signal Levels Receive: 0 to -30 dB Transmit: 0 dB, -7.5 dB, -15 dB, -22.5 dB, with CSU ±2.7V ±10%, adjustable, measured in range 0 to 655 feet, without CSU Jitter Performance AT&T TR-62411, G.
IPmux-1/1E Installation and Operation Manual Interfaces Chapter 1 Introduction FXS: Loop start for direct connection to a 2-wire telephone Nominal level: 0 dBm Nominal impedance: 600Ω Return loss (ERL): Better than 20 dB Frequency response: (Ref: 1020 Hz) • ±0.5 dB, 300 TO 3000 Hz • ±1.1 dB, 250 to 3400 Hz Signal to total distortion, G.712, G.
IPmux-1/1E Installation and Operation Manual Chapter 1 Introduction T1 Indicators Signal Levels Receive: 0 to -10 dB Transmit Balanced: ±3V ±10% Transmit Unbalanced: ±2.37V ±10% Jitter Performance ITU-T G.823 standard External Adapter Cable TBNC to BNC required Compliance ANSI T1.403, ITU-T Rec. G.703, G.704 Connector RJ-45, 8-pin Data Rate 1.544 Mbps Line Code B8ZS, B7ZS, AMI Line Impedance Balanced: 100Ω Signal Levels Receive: 0 to -10 dB Transmit: ±2.
IPmux-1/1E Installation and Operation Manual Power Power Supply Chapter 1 Introduction 1 power supply 100 to 240 VAC, 50 or 60 Hz -36 to -72 VDC (-48 VDC nominal) Note: IPmux-1E has only AC power supply option. Power Consumption Physical IPmux-1: 4W IPmux-1 (with Ethernet switch): 10W IPmux-1E: 25W IPmux-1E (with Ethernet switch): 32W IPmux-1 Height Width Depth Weight 4.4 cm/1.7 in (1U) 21.4 cm/8.4 in 24.6 cm/9.7 in 1.2 kg/2.7 lb IPmux-1E Height Width Depth Weight 4.4 cm/1.7 in (1U) 43.2 cm/17.
Chapter 1 Introduction 1-38 IPmux-1/1E Installation and Operation Manual Technical Specifications
Chapter 2 Installation This chapter includes: • Site requirements and prerequisites • Package contents • Equipment needed • Installation and setup 2.1 Introduction IPmux-1/1E is delivered completely assembled for bench-top installation. The only mechanical installation procedures that may be necessary are optional installation in a 19-inch rack. Use RM-25 for IPmux-1, RM-26 for IPmux-1E.
IPmux-1/1E Installation and Operation Manual Chapter 2 Installation 2.2 Site Requirements and Prerequisites Install AC-powered IPmux-1/1E units within 1.5m (5 feet) of an easily-accessible grounded AC outlet capable of furnishing the required supply voltage, in the range of 100 to 240 VAC. DC-powered IPmux-1 units require a 48 VDC power source. The positive pole can be earthed. The maximum permissible current capability of the branch distribution circuit that supplies power to the product is 16A.
IPmux-1/1E Installation and Operation Manual Chapter 2 Installation 2.4 Equipment Needed IPmux-1/1E needs no special tools for installation. A screwdriver is necessary when mounting IPmux-1/1E in a 19-inch rack. 2.5 Installation and Setup Setting Jumpers IPmux-1 IPmux-1 internal jumpers and switches do not need to be configured by the user. Therefore, removing the product cover is not required. IPmux-1E The IPmux-1E FXS/FXO/E&M version needs NO user internal jumper configuration.
Chapter 2 Installation IPmux-1/1E Installation and Operation Manual Only qualified and authorized service personnel should have access to the inside of the unit. Warning Disconnect the unit from the power line and from all the cables before removing the cover. Line voltages are present inside IPmux-1/ 1E when it is connected to power. Moreover, under certain external fault conditions, dangerous voltages may appear on the lines connected to IPmux-1/1E.
IPmux-1/1E Installation and Operation Manual Chapter 2 Installation Connecting Interfaces and Cables Figure 2-2 through Figure 2-5 illustrate the front and rear panel options available for IPmux-1. Figure 2-6 through Figure 2-9 illustrate the rear and front panel options available for IPmux-1E. Figure 2-2. IPmux-1 Front Panel Figure 2-3. IPmux-1 Front Panel for Two Ethernet Ports POWER 100-230 VAC 1.
IPmux-1/1E Installation and Operation Manual Chapter 2 Installation IPmux-1E Figure 2-6. IPmux-1E Front Panel IPmux-1E Figure 2-7. IPmux-1E Front Panel for Two Ethernet Ports 1.6A T 250V 100-240 VAC POWER CAUTION : IISDN S I/O 3 1 2 3 4 Figure 2-8. IPmux-1E Rear Panel (ISDN BRI Option) 1.6A T 250V 100-240 VAC POWER CAUTION : IISD N S I/O 3 1 2 3 4 Figure 2-9.
IPmux-1/1E Installation and Operation Manual Chapter 2 Installation Location of Connectors Interface connections are made from the IPmux-1/1E back panel, as shown in Figure 2-2. • Table 2-1 lists the E1/T1 port pinout. • Table 2-2 lists the Ethernet port pinout. • Table 2-3 lists the Control port pinout. • Table 2-4 lists the ISDN-S connector pinout. • Table 2-5 lists the FXS/FXO/E&M connector pinout for RJ-11. Table 2-1.
IPmux-1/1E Installation and Operation Manual Chapter 2 Installation Table 2-3. Control Port Pinout Pin Pinout 1 – 2 Rx 3 Tx 4 – 5 GND 6 – 7 – 8 – 9 – Table 2-4.
IPmux-1/1E Installation and Operation Manual Chapter 2 Installation Table 2-5.
IPmux-1/1E Installation and Operation Manual Chapter 2 Installation Table 2-7. External Clock Port Pinout Pin Number Signal Name Function 1 RRING Rx 2 RTIP Rx 3 GND Usually not connected 4 TRING Tx 5 TTIP Tx 6 GND Usually not connected 7 – Not connected 8 – Not connected Connecting the Power To connect power to IPmux-1/1E, refer to the appropriate section below, depending on your version of the unit (AC or DC).
IPmux-1/1E Installation and Operation Manual Chapter 2 Installation DC Power Connection A DC power supply option is available to be ordered for IPmux-1 only (not available for IPmux-1E. For information about connecting the DC power supply refer to the DC Power Supply Connection Supplement. Warning Due to the high current capability of DC mains systems, care should be taken when connecting the DC supply, in order to avoid short-circuits and fire hazards.
Chapter 2 Installation 2-12 Installation and Setup IPmux-1/1E Installation and Operation Manual
Chapter 3 Operation This chapter: • Provides a detailed description of the front panel controls and indicators and their functions • Explains power-on and power-off procedures • Provides instructions for using a terminal connected to the IPmux-1/1E Control port • Describes how to navigate menus • Illustrates the following menus: − Main menu − Configuration menu − Viewing System Information − Monitoring IPmux-1/1E performance. For a detailed explanation of parameters on the menus, see Appendix E.
IPmux-1/1E Installation and Operation Manual Chapter 3 Operation 1 4 3 2 7 5 Figure 3-1. IPmux-1 Front Panel LEDs 8 POWER 100-230 VAC 1.6A T 250V CAUTION : FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE AND RATING OF FUSE. E1 ETH Figure 3-2. IPmux-1 Rear Panel Switch Table 3-1. IPmux-1 System Indicators and Switches No.
IPmux-1/1E Installation and Operation Manual Chapter 3 Operation Table 3-1. IPmux-1 System Indicators and Switches (Cont.) No. Name Type Function 7 ETH FDX LED On: Full-duplex Off: Half-duplex 8 1 POWER Switch Turns IPmux-1/1E power On and Off 2 IPmux-1E 4 5 6 7 3 Figure 3-3. IPmux-1E Front Panel Indicators 8 POWER : IISD N S 1A T 250V 100-240 VAC CAUTION I/O 3 1 2 3 4 Figure 3-4. IPmux-1E Back Panel Indicators Table 3-2.
IPmux-1/1E Installation and Operation Manual Chapter 3 Operation Table 3-2. IPmux-1E (BRI/FXS/FXO/E&M) System Indicators and Switches (Cont.) No. Name Type Function 4 ETH LINK LED On: Line OK Off: Link not active 5 ETH ACT LED On: Frame being transferred on line Off: No activity 6 7 ETH 100M LED ETH FDX LED On: 100 Mbps Off: 10 Mbps On: Full-duplex Off: Half-duplex 8 3.
IPmux-1/1E Installation and Operation Manual Chapter 3 Operation 6. Press to open the configuration software. 7. Enter your User Name according to your assigned system privileges (either Supervisor (su) or User and then your Password when prompted (the factory-set password is xxxxxxxxxx). The Main Menu is displayed (Figure 3-11). Note If the password is invalid in three consecutive attempts, the system becomes inaccessible for 15 minutes. Login User Name and Password To enter as a superuser: 1.
IPmux-1/1E Installation and Operation Manual Chapter 3 Operation 3.3 Getting Started After installation, there are no special operating procedures for IPmux-1/1E. Once it is powered up, the unit operates automatically. The front panel LED indicators (Figure 3-1 and Figure 3-3) indicate proper operation. The unit operational status can be monitored constantly. If required, IPmux-1/1E can be reconfigured.
IPmux-1/1E Installation and Operation Manual Chapter 3 Operation Main Menu 2. Configuration 1. System 3.Performance Monitoring 4. Exit 1.General Information 1. E1/T1 Statistics 2.Self-Test Results 2.LAN Status 3. Reset 3. Bundle Connection Status 4.Event Log 4.Bundle Connection Statistics 5. Ping One-port LAN Option 1. General Configuration 2. E1/T1 Configuration 1. Host IP 1. Channel Status 2. Management Configuration 2. Transmit Clock Source 3. ASCII Terminal Configuration 3.
IPmux-1/1E Installation and Operation Manual Chapter 3 Operation Main Menu 2. Configuration 1. System 3.Performance Monitoring 1.General Information ISDN Statistics 2.Self-Test Results 2.LAN Status 3. Reset 3. Bundle Connection Status 4.Event Log 4.Bundle Connection Statistics 5. Ping 1. General Configuration 2. ISDN Configuration 1. Host IP 1. Interfaces Mode 2. Management Configuration 2. Transmit Clock Source 3. ASCII Terminal Configuration 3. Channel Configuration 4.
IPmux-1/1E Installation and Operation Manual Chapter 3 Operation Main Menu 2. Configuration 1. System 3.Performance Monitoring 1.General Information 1. Analog Status 2.Self-Test Results 2.LAN Status 3. Reset 3. Bundle Connection Status 4.Event Log 4.Bundle Connection Statistics 4. Exit 5. Ping One-port LAN Option 1. General Configuration 1. Host IP 2. Analog Configuration 1. Clock Source 2. Management Configuration 2. Far End Type 3. ASCII Terminal Configuration 3.
IPmux-1/1E Installation and Operation Manual Chapter 3 Operation Main Menu 2.Configuration 3.Connection Configuration 1.Connection Mode 2. Bundle Connection Configuration 3. Secondary IP Address 4. Secondary IP Mask 1. Bundle ID 1. Primary Bundle ID 2. IP TOS 2. Secondary Bundle ID 3. TDM Bytes in a Frame 3. Redundancy Type 4. Connection Status 4. TDM Fail Time 5. Destination IP Address 5. Event Threshold Window 6. Next Hop 6. Sequence Number Threshold 7. Destination Bundle 7.
IPmux-1/1E Installation and Operation Manual Chapter 3 Operation Main Menu 2.Configuration 3.Connection Configuration 1.Connection Mode 2. Bundle Connection Configuration 3. Activation Criterion 1. Bundle ID 1. Pattern ID 2. IP TOS 2. Tx A 3. Active Time Slot Bytes in Frame 3. Tx B 4. Connection Status 4. Tx C 5. Destination IP Address 5. Tx D 6. Next Hop 7. Destination Bundle 8. Jitter Buffer 9. OAM Connectivity A. Redundancy Function B. VLAN Tagging C. VLAN ID E.
IPmux-1/1E Installation and Operation Manual Chapter 3 Operation Main Menu 2.Configuration 3.Connection Configuration 1.Connection Mode 2. Bundle Connection Configuration 1. Bundle ID 2. IP TOS 3. Packet Delay 4. Connection Status 5. Destination IP Address 6. Next Hop 7. Source UDP 8. Destination UDP 9. Jitter Buffer B. VLAN Tagging C. VLAN ID E. VLAN Priority Figure 3-10. IPmux-1E Connection Configuration Menu Tree for CESoIP Mode Main Menu Figure 3-11 shows the IPmux-1/1E Main Menu.
IPmux-1/1E Installation and Operation Manual Chapter 3 Operation Table 3-3. IPmux-1/1E Main Menu Options Option Description 1. System View and modify system parameters 2. Configuration Define system configuration 3. Performance Monitoring Monitor system performance 4. Exit Exit the control software MAIN MENU 1.System 2.Configuration 3.Performance Monitoring 4.Exit > > > Select item from the menu: _ Use keys <1> to <4> Figure 3-11.
IPmux-1/1E Installation and Operation Manual Chapter 3 Operation SYSTEM 1. General Information 2. Self-Test Results 3. Reset 4. Event Log > 5. Ping ESC. Exit Select item from the menu. Figure 3-12. IPmux-1/1E System Menu Setting IPmux-1/1E Configuration Options To access the Configuration menu: Main Menu ↓ 2. Configuration • Type 2 (Configuration) in the Main Menu. The IPmux-1E E1/T1 Configuration menu is shown in Figure 3-5 and Figure 3-13.
IPmux-1/1E Installation and Operation Manual Chapter 3 Operation CONFIGURATION 1. General Configuration 2. ISDN Configuration 3. Connection Configuration 4. LAN Configuration ESC. Exit Select item from the menu: _ Figure 3-14. IPmux-1E ISDN-S Configuration Menu CONFIGURATION 1. General Configuration 2. Analog Configuration 3. Connection Configuration 4. LAN Configuration ESC. Exit Select item from the menu: _ Figure 3-15.
IPmux-1/1E Installation and Operation Manual Chapter 3 Operation Performance Monitoring To view Performance Statistics: • Type 3 (Performance Monitoring) in the Main menu. Typical menus are shown in Figure 3-16, Figure 3-17, and Figure 3-18. Table 3-6 describes the Performance Monitoring options. Further details for specific parameters are explained in Appendix E. PERFORMANCE MONITORING 1. E1/T1 Statistics 2. LAN Status 3. Bundle Connection Status 4. Bundle Connection Statistics ESC.
IPmux-1/1E Installation and Operation Manual Chapter 3 Operation PERFORMANCE MONITORING 1. Analog Status 2. LAN Status 3. Bundle Connection Status 4. Bundle Connection Statistics ESC. Exit Select item from the menu. Figure 3-18. Performance Monitoring Menu for IPmux-1E FXS/FXO/E&M Table 3-6. Performance Monitoring Menu Options Option Description 1. E1/T1/ ISDN/ Analog Statistics Statistics for E1/T1, ISDN, or FXS/FXO/E&M – updated at 15 minute intervals 2. LAN Status Status of Lan port(s) 3.
Chapter 3 Operation 3-18 Overview of Menu Operations IPmux-1/1E Installation and Operation Manual
Chapter 4 Troubleshooting and Diagnostics This chapter describes how to: • Detect errors • Troubleshoot problems • Perform diagnostic tests. 4.1 Error Detection Using Front Panel LEDs LED indicators on the front panel IPmux-1/1E indicate the operating status of the module. The LED indicators are described in Chapter 3 of this manual. Working with the Alarm Buffer IPmux-1/1E maintains an Event Log File. All events are time-stamped.
IPmux-1/1E Installation and Operation Manual Chapter 4 Troubleshooting and Diagnostics Table 4-1.
IPmux-1/1E Installation and Operation Manual Chapter 4 Troubleshooting and Diagnostics Table 4-1. Event Types (Cont.) Event Description Corrective Action LOS END LOS state detected has ended None LOS START IPmux-1 has a LOS (loss of signal) state on its E1/T1 port 1.
Chapter 4 Troubleshooting and Diagnostics IPmux-1/1E Installation and Operation Manual 4.2 Troubleshooting Table 4-2 presents the event types as they appear on the Event Log File and lists the actions required to correct the event (alarm) indication. For further information, see Chapter 3. Table 4-2. IPmux-1 Troubleshooting Chart Fault Probable Cause Remedial Action E1/T1 equipment connected to IPmux-1 is not synchronized with IPmux-1/1E. Configuration problems 1.
IPmux-1/1E Installation and Operation Manual 4.3 Chapter 4 Troubleshooting and Diagnostics Performance Monitoring and Troubleshooting Statistics IPmux provides powerful performance monitoring and troubleshooting tools, which consist of the following four levels (screens): • E1/T1 statistics – Status of the physical E1/T1 parameters (signal, framing, etc.) • LAN statistics – Ethernet connection status (speed, duplex mode, bytes transmitted & received, etc.
IPmux-1/1E Installation and Operation Manual Chapter 4 Troubleshooting and Diagnostics E1 Statistics E1 over UTP LOS: 0 LOF (Red) 0 LCV: 0 RAI (Yellow) 0 AIS: 0 FEBE: 0 BES: 0 SS: 0 SES: 0 UAS: 0 LOMF: 0 Time Since: 700 1. Interval 0 ESC> Exit sec ------------------Valid Intervals 1--- N. Next Inv Figure 4-1. E1 Statistics Note 4-6 E1/T1 statistics are monitored and saved under consecutive Intervals. Each Interval is 15 minutes long.
IPmux-1/1E Installation and Operation Manual Chapter 4 Troubleshooting and Diagnostics The physical E1/T1 alarms are: • LOS • LOF (RED) • LCV • RAI (Yellow) • AIS • FEBE • BES • DM • ES • SES • UAS • LOMF They are described in Table 4-3.
4-8 LOF (Red) A Loss of Signal indicates that there is either no signal arriving from the adjacent E1/T1 device or no valid E1 voltage mask or no voltage alteration between positive and negative amplitudes. LOS Performance Monitoring and Troubleshooting Statistics Check all framing related parameters (CRC-4, CAS enabled/disabled, ESF/D4 (for T1), etc.), and physical connections.
AIS RAI (Yellow) A Line Code Violation indicates an error on the pulse structure, either a Bipolar Violation (BPV) or an Excessive Zeros (EXZ) error event. LCV Performance Monitoring and Troubleshooting Statistics 4-9 Check why the E1/T1 device is sending AIS (all ones) stream towards IPmux, for example, Red alarm on a different interface of E1/T1 device (upstream). Recommendations: When receiving AIS the Sync front panel LED is off.
4-10 ES DM BES A Far End Block Error is sent to transmitting device notifying that a flawed block has been detected at the receiving device. Exists only for E1 MF-CRC4. FEBE Performance Monitoring and Troubleshooting Statistics Check physical link integrity. Follow the recommendation concerning LOF, BEF and AIS. Recommendations: If SES is active ES runs for 10 seconds and then stops.
LOMF UAS A Severely Errored Second is a second containing one of the following: SES Chapter 4 Troubleshooting and Diagnostics Performance Monitoring and Troubleshooting Statistics 4-11 Check physical link integrity, signaling method (CAS enable only), and framing-related parameters. Recommendations: A Loss of Multi Frame indicates there is no sync on the multi frame mode, i.e.
IPmux-1/1E Installation and Operation Manual Chapter 4 Troubleshooting and Diagnostics LAN Statistics One Ethernet Port To view the LAN statistics: • Access the ASCII control port terminal via: Main Menu Æ Performance Monitoring Æ LAN Statistics.
IPmux-1/1E Installation and Operation Manual Chapter 4 Troubleshooting and Diagnostics The LAN Statistics parameters are: • MAC Address • Mode • Rate (Mbps) • Status • Frames Received − Correct Frames − Correct Octets − Alignment Error − FCS Errors • Frames transmitted − Correct Frames − Correct Octets − Single Collision − Multi-Collision − Deferred Transmission − Late Collision − Carrier Sense.
MAC address of the local port. Port mode is set either manually or via the auto-negotiation mode (under LAN configuration screen). MAC Address Mode The number of frames received that are not an integral number of octets in length (RFC 1643). All frames should end on an 8-bit boundary, but physical problems on the network could cause the number of bits to deviate from the multiple of eight. Alignment Errors 4-14 FCS Errors The number of octets successfully received.
Description Collisions occur only in Half-duplex mode (RFC 1643). Counts the successfully transmitted frames for which transmission is inhibited by exactly one collision (see Collision above). Single Collision Carrier Sense Late Collision Deferred Transmission Multi Collision The number of octets successfully transmitted. When a valid connection is established the number should increase steadily. Correct Octets Check connection between the interface and its Ethernet transceiver.
IPmux-1/1E Installation and Operation Manual Chapter 4 Troubleshooting and Diagnostics With User Ethernet Port To view the LAN statistics: • Access the ASCII control port terminal via: Main Menu Æ Performance Monitoring Æ LAN Statistics.
IPmux-1/1E Installation and Operation Manual Chapter 4 Troubleshooting and Diagnostics The LAN Statistics parameters are: • MAC Address • Mode • Rate (Mbps) • Status • Frames Received − Total Frames − Total Octets − Oversize Frames − Fragments − Jabber − Dropped Frames − CRC Errors • Frames Transmitted − Correct Frames − Correct Octets − Collisions − Multi-Collision.
MAC address of the local port. Port mode is set either manually or via the auto-negotiation mode (under LAN configuration screen). MAC Address Mode Link status: Status Number of frames exceeding the maximum allowed frame size, but are otherwise valid Ethernet frames (good CRC). The number of frames that are shorter than 64 bytes and have an invalid CRC. The number of frames that are too long and have an invalid CRC.
Description The number of octets successfully transmitted. When a valid connection is established the number should increase steadily. The number of successfully transmitted frames which transmission is inhibited by a collision event. A collision occurs in half-duplex connection when two devices try to transmit at the same time. This counter tracks the number of times frames have collided. This event exists only in Half Duplex mode, which is not recommended in an IPmux application.
Chapter 4 Troubleshooting and Diagnostics IPmux-1/1E Installation and Operation Manual Bundle Connection Statistics The Bundle Connection Status screen provides information about the integrity of the TDMoIP connection, including the status of the Jitter Buffer. (Each bundle has it own independent Jitter Buffer). To view the Bundle connection status: • Access the control port terminal via: Main Menu Æ Performance Monitoring Æ Bundle Connection Status. BUNDLE CONNECTION STATUS Destination IP Address 192.
Layer 2 Applications: the MAC address displayed is the MAC address of the remote IPmux. Next Hop MAC Address Connectivity Status The IP address of the opposite IPmux, to which the bundle is destined. Destination IP Address Chapter 4 Troubleshooting and Diagnostics Performance Monitoring and Troubleshooting Statistics 4-21 Note: While under Disable or Local Failure or Remote Failure status, the statistic counters will be inactive.
4-22 Each packet transmitted by IPmux holds a sequence number. The receiving IPmux checks these numbers at the receive mechanism and expects to see that each new incoming packet is “in sequence” relative to the previous one (i.e., packet no. 5 is received after no. 4). When, for some reason, this is not the case (i.e., next packet is not in sequence relative to the previous one), this means that there had been a problem with packet flow integrity (and hence data/voice integrity).
The IPmux is equipped with a “Packet Delay Variation Tolerance” buffer, also called a “Jitter Buffer”, responsible for compensating for IP networks delay variation (IP jitter). The Jitter Buffer is configured in milliseconds units and exists for each bundle independently. Jitter Buffer Underflow Performance Monitoring and Troubleshooting Statistics 4-23 When an Overflow (see below) situation occurs, the IPmux instantly flashes the Jitter Buffer, causing a forced Underflow.
4-24 Jitter Buffer Overflows Recommendations: Jitter Buffer Underflow (cont.) Table 4-6. Bundle Connection Status Parameters (Cont.) IPmux-1/1E Installation and Operation Manual Performance Monitoring and Troubleshooting Statistics Make sure the same amount of TS for bundle is configured on each side of the IPmux application, and that the “TDM bytes in frame” parameter is identical in both IPmux units.
IPmux-1/1E Installation and Operation Manual Chapter 4 Troubleshooting and Diagnostics 4.4 Diagnostic Tests Maintenance capabilities include external and internal loopbacks. E1/T1 External Loop IPmux-1 can be set to an external loop to test the connection between the E1/T1 port and the PBX (refer to IPmux-1 E1/T1 Configuration in Appendix E). In this mode, data coming from the PBX is both looped back to the PBX and transmitted forward to the IP network (see Figure 4-5).
Chapter 4 Troubleshooting and Diagnostics IPmux-1/1E Installation and Operation Manual ISDN BRI External Loop An external loop on IPmux-1E can be set to test the ISDN “S’ line (Figure 4-7). The test is performed on B channels only. Figure 4-7. IPmux-1E/ISDN External Loop Internal Loop An internal loop on IPmux-1E can be set to test the ISDN “S’ line (Figure 4-8). The test is performed on B channels only. Figure 4-8. IPmux-1E/ISDN Internal Loop Main Menu ↓ 2. Configuration ↓ 2. ISDN Configuration ↓ 3.
IPmux-1/1E Installation and Operation Manual Chapter 4 Troubleshooting and Diagnostics 4.5 Frequently Asked Questions Question: How does the IPmux handle/propagate alarms on the TDM and Ethernet side? Answer The IPmux handles alarms on the TDM and Ethernet side in the following manner: TDM Side Alarms: Unframed mode: 1. In case of LOS (Loss Of Signal) on the local IPmux side, AIS will be sent towards the IP side, and will then be transferred over the E1/T1 to the remote TDM device. 2.
Chapter 4 Troubleshooting and Diagnostics IPmux-1/1E Installation and Operation Manual Question: How can I ensure the IPmux TDMoIP traffic priority over an IP Ethernet network? Answer The IPmux family is equipped with three different features that can be implemented in order to give the IPmux TDMoIP traffic priority over an IP/Ethernet network: • VLAN ID (Layer 2) • ToS field (Layer 3) • UDP destination port (Layer 4) Each QoS feature is based on a different OSI level and can be used individually in
IPmux-1/1E Installation and Operation Manual Chapter 4 Troubleshooting and Diagnostics of 2142, hence all the packets leaving the IPmux are tagged accordingly. This unique value was assigned to RAD by the IANA organization for TDMoIP applications. The network elements may be used to give priority to the TDMoIP traffic according to the UDP destination field.
Chapter 4 Troubleshooting and Diagnostics 4-30 Frequently Asked Questions IPmux-1/1E Installation and Operation Manual
Appendix A Boot Sequence for Downloading Software A.1 General This chapter provides a description of the IPmux-1/1E boot procedure via an ASCII terminal for downloading software. The IPmux-1/1E software is stored in flash memory in two sections, in the boot sector and in the file system. The boot sector holds a boot program that calls up the rest of the program from the file system. The file system can hold two compressed copies of the IPmux-1/1E code.
Appendix A Boot Sequence for Downloading Software IPmux-1/1E Installation and Operation Manual BOOT Program V 1.21 7-1-2001 08:35 Flash : size 3e0000h, FileSys sectors 62 BOOT Program is running !!! Checking File System.........-> exists. Backup file EXIST Operating file EXIST Press Cntl-A within 3 seconds to get File-System Menu !!! #c1cod code: V 2.00 8-9-2000 11:58 got start addr : 100000 Decompression-process........ Decompression Ended !!! Jumping to Application, addr = 100008. Figure A-1.
IPmux-1/1E Installation and Operation Manual Appendix A Boot Sequence for Downloading Software BOOT MENU The device can store two software files in its File System. One is called Operating file and the Second is called Backup file. Operating file EXIST Backup file EXIST Configuration file EXIST 0. Exit 1. File swap: Operating⇔Backup 2. Download NEW Operating file (existing Operating file will be saved as Backup) 3. Delete Operating file (existing Backup file will be saved as Operating) 4.
Appendix A Boot Sequence for Downloading Software A-4 Booting IPmux-1/1E IPmux-1/1E Installation and Operation Manual
Appendix B Telnet B.1 General Telnet, which stands for Telecommunications Network, is a protocol that gives you the ability to connect to a remote machine, by giving commands and instructions interactively to that machine, thus creating an interactive connection. In such a case, the local system becomes transparent to the user, simulating a direct connection to the remote computer.
IPmux-1/1E Installation and Operation Manual Appendix B Telnet Figure B-1. Telnet Logon Dialog Telnet Operation Telnet and ASCII terminal cannot be active at the same time. If a terminal is active, a Telnet session cannot be established. To establish a Telnet session: • Exit the terminal by selecting Exit in the Main menu. If the auto-disconnect is ON, the terminal will be disconnected automatically after 15–30 minutes if no characters were sent (see ASCII Terminal Configuration in Appendix E).
IPmux-1/1E Installation and Operation Manual Appendix B Telnet Telnet Access IPmux-1/1E has the ability to configure Telnet access: • Enable –Telnet is enabled • Disable – Telnet is disabled • Managers – Initially Telnet access is permitted to any outside computer. Once there is at least one manager defined in the Manager’s List, Telnet access is allowed only to managers in the list (see Management Configuration).
Appendix B Telnet B-4 Using Telnet to Manage the IPmux-1/1E IPmux-1/1E Installation and Operation Manual
Appendix C SNMP Management Appendix C provides specific information for IPmux-1/1E management by SNMP (Simple Network Management Protocol). The SNMP management functions of IPmux-1/1E are provided by an internal SNMP agent. The SNMP management communication uses UDP (User Datagram Protocol), which is a connectionless-mode transport protocol, part of the IP (Internet Protocol) protocol suite. This appendix covers the information related to the SNMP environment. C.
Appendix C SNMP Management IPmux-1/1E Installation and Operation Manual Management Information Base (MIB) The MIB includes a collection of managed objects. A managed object is defined as a parameter that can be managed, such as a performance statistics value. The MIB includes the definitions of relevant managed objects. Various MIBs can be defined for various management purposes or types of equipment.
IPmux-1/1E Installation and Operation Manual Appendix C SNMP Management • rfc2233.mib (IF-MIB) • rfc1493.mib • rfc2665.mib • rfc1907.mib • rfc2493.mib • ces.mib • rfc2127 (ISDN-MIB) • rfc2495.mib (except Far End objects and RW configuration objects which are different for each configuration) - replaces RFC 1406; which is now obsolete. • rfc2494.mib • rfc2239.mib • IP-MUX RAD private mib The IPmux-1 object id is iso (1).org(3).dod(6).internet(1).private(4).enterprises(1).rad(164).
Appendix C SNMP Management IPmux-1/1E Installation and Operation Manual In general, SNMP agents support two types of access rights: Read-Only: The SNMP agent accepts and processes only SNMP getRequest and getNextRequest commands from management stations which have a Read-Only community name. Read-Write: The SNMP agent accepts and processes all the SNMP commands received from a management station with a Read-Write community name.
Appendix D TFTP Download Procedures D.1 Inband TFTP Download Procedure General New IPmux-1 software version can be downloaded to IPmux-1 using TFTP. There are three possible procedures: • Users who access IPmux using Telnet can perform software download and configuration upload/download using the configuration screens. For details, see TFTP in Appendix E). • Users who have access to the RADview Network Management – for more details refer to RADview-HPOV Network Management System for IP Applications.
IPmux-1 Installation and Operation Manual Appendix D TFTP Download Procedures Preliminary Procedure Before performing TFTP download: 1. Ping IPmux-1 from the station running the TFTP server to ensure that IPmux-1 has communication with the machine. 2. Log in as SUPERUSER (su). 3. Edit the file named inetd.conf found at the /etc directory, as follows: − Search for the line starting with a # sign followed by tftp, for example, # tftp and delete the # sign.
IPmux-1 Installation and Operation Manual Appendix D TFTP Download Procedures Figure D-2. Agent and Server IP Addresses Checking the Download To check the download: 1. Log on the MIB Browser again, as follows: iso.org.dod.internet.mgmt.mib-2.system.sysDescr. The MIB Browser window showing the system description is displayed (see Figure D-3). 2. Press . 3. Scroll right to check that the application version you have just loaded is the correct one.
Appendix D TFTP Download Procedures IPmux-1 Installation and Operation Manual Figure D-3.
Appendix E Configuration Menus This appendix illustrates the IPmux-1/1E screens and explains the parameters for: • Main Menu in Section E.1 • Viewing the IPmux-1/1E System in Section E.2 General Information Self-Test Results Reset System Event Log Logfile Events Ping • General Configuration in Section E.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus • Connection Configuration for Static Mode in Section E.6 Bundle Connection Configuration Protection Switching Configuration • Connection Configuration for Dynamic CAS Mode in Section E.7 Bundle Connection Configuration Activation Criterion Configuration • Connection Configuration for CESoIP Mode: Bundle Connection Configuration in Section E.8 Bundle Connection Configuration • LAN Configuration (no User port) in Section E.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus MAIN MENU 1.System > 2.Configuration > 3.Performance Monitoring > 4.Exit Select item from the menu:_ Use keys <1> to <4> Figure E-1. IPmux-1/1E Main Menu The following sections in this appendix explain the parameters in each of the menu options. E.2 Viewing the IPmux-1/1E System General Information Main Menu ↓ 1. System Menu ↓ 1.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus GENERAL INFORMATION Software Version Hardware Version Boot: 1.21 7-1-2001 08:35 HW:0.0/0.0/0.0 Inventory No. 314153 Application: 2.00 9-4-01 12:02 Backup: 2.00 9-4-01 12:02 Interface Description ISDN-S over UTP ETHERNET over UTP Press ESC to exit Figure E-3. General Information Window – ISDN GENERAL INFORMATION Software Version Hardware Version Inventory No. Boot: 1.21 7-1-2001 08:35 HW:0.0/0.0 314154 Application: 2.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus For details: • Type M. If a problem is encountered refer to Chapter 4. Reset Main Menu ↓ 1. System Menu ↓ 3. Reset To reset the IPmux-1/1E configuration: 1. Type 3 (Reset) in the System Menu. A confirmation message appears. 2. Press Y to confirm System Reset for IPmux-1/1E. Are you sure you want a total reset??? (Y/N) Figure E-6. Reset Confirmation Message System Event Log System Event Log Main Menu ↓ 1. System Menu ↓ 4.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus Logfile Events Main Menu ↓ 1. System Menu ↓ 4. Event Log ↓ 1. Read Logfile LOGFILE EVENTS 2053-08-07 00:01:20 LOS START TDM SLOT 2053-08-07 00:01:20 COLD START 2053-08-07 00:01:20 LOS START TDM SLOT 2053-08-07 00:01:20 COLD START 2053-08-07 00:01:20 LOS START TDM SLOT 2053-08-07 00:01:20 COLD START 2053-08-07 00:01:20 LOS START TDM SLOT 2053-08-07 00:01:20 COLD START ESC. Exit N. Next Figure E-8.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus PING Enter Destination IP And Press Enter. Destination IP: 1.1.1.2 Use Space Bar To Choose VLAN Tagging. VLAN Tagging: Yes Enter VLAN ID(0..4095) And Press Enter. VLAN ID: 2 Enter VLAN Priority(0..7) And Press Enter. VLAN Priority: 6 Use Space Bar To Choose Ping Repetitions. Ping Repetitions: Endless repeats |-----------------------------------------------------| | Ping Result: Host 1.1.2.1 Request Timed Out.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus Host IP Main Menu ↓ 2. Configuration ↓ 1. General Configuration Note ↓ 1. Host IP To configure the Host IP address and IP Mask: 1. On the Host IP menu, select 1 and type the IP Address. 2. On the Host IP menu, select 2 and type the IP Mask. x DHCP status (item 5) appears only when DHCP (item 4) is enabled. HOST IP 1. IP Address 192.168.217.12 2. IP Mask 255.255.255.0 3. Default Gateway 0.0.0.0 4. DHCP Enable 5.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus DHCP Status Main Menu ↓ 2. Configuration ↓ 1. General Configuration ↓ 1. Host IP ↓ 5. DHCP Status DHCP STATUS Server ID: 0.0.0.0 Lease Expiration Time: No Active Lease Current Status: Trying to locate available server ESC. Exit Management Configuration Main Menu ↓ 2. Configuration ↓ 1. General Configuration ↓ 2. Management Configuration MANAGEMENT CONFIGURATION 1. Authentication/Community > 2. Managers List > 3.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus Table E-3.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus Table E-4. Manager List Parameters Parameter Possible Values Remarks Manage IP Address 0.0.0.0. to 255.255.255.255 Sets the Manager IP address Link Up/Down Trap On, Off Link Down informs the Manager that there is a physical failure. Link Up informs the Manager that the device has recovered from the failure.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus Table E-6. IPmux-1/1E Alarms Alarm ID Alarm Description Trap Sent to NMS 1 Loss of Signal (LOS Physical Layer) Alarm LOS 1.3.6.1.4.1.164.6.1.3.0.7 2 Loss of Frame (LOF Physical Layer) Alarm LOF 1.3.6.1.4.1.164.6.1.3.0.8 6 Alarm Indication Signal Received (AIS Line Physical Layer) Alarm AIS 1.3.6.1.4.1.164.6.1.3.0.10 8 Remote Defect Indication Received (RDI Line Physical Layer) Alarm RDI 1.3.6.1.4.1.164.6.1.3.0.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus Table E-7. ASCII Terminal Configuration Parameters Name Possible Values Display Mode Color MonoChrome 3 color MonoChrome 2 color Baud Rate 9600, 19200, 38400, 57600, 115200 – in units of bps Remarks Default: 19200 bps Change Password 15 Min.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus DOWNLOAD/UPLOAD USING XMODEM 1. File Application code ESC. Exit D. Download Select item from the menu. Use key or keys <1> to <1> Figure E-18. Download/Upload Using X-Modem Window Table E-9.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus Table E-10. Download/Upload Using TFTP Parameters Parameter Possible Values Remarks File Name Command No Operation, Software Download, Configuration Download, Configuration Upload Server IP 0.0.0.0 to 255.255.255.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus Set Default Parameters Main Menu ↓ 2. Configuration ↓ 1. General Configuration ↓ 6. Set Default Parameters Setting Default Parameters reconfigures the device according to default parameters. Before overwriting the system, the warning in Figure E-21 appears asking you to confirm your selection. Configuration will be overwritten and system will RESET. Continue ? (Y/N) Figure E-21.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus E.4 IPmux-1 E1/T1 Configuration IPmux-1 automatically detects whether the interface is E1 or T1, and the appropriate menu appears (see Figure E-24 and Figure E-25). E1 Configuration E1 CONFIGURATION Main Menu ↓ 2. Configuration (E1) ↓ 2. E1/T1 Configuration 1. Channel Status Enable 2. Transmit Clock Source Adaptive 3. Loopback State Disable 4. Rx. Sensitivity -10dB 5. Line Type CRC4 enable 6. Idle Code 7E 7.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus Table E-12. E1 Physical Layer Configuration Parameters (Cont.) Parameter Possible Values Remarks Loopback State Internal Data received from the IP network side will be looped back to the network transmit line. An unframed all ‘1’ code (AIS) will be transmitted in the E1 Tx path toward the PBX. Incoming data from the PBX will be ignored.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus Table E-12. E1 Physical Layer Configuration Parameters (Cont.) Parameter Uplink Fail Alarm Behavior Possible Values Remarks Selects notification by the agent TDM side if Ethernet link fails Cond AIS IPmux-1/1E sends a Cond.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus T1 Configuration T1 CONFIGURATION Main Menu ↓ 2. Configuration (T1) ↓ 2. E1/T1 Configuration 1. Channel Status Enable 2. Transmit Clock Source Adaptive 3. Loopback State Disable 4. Line Type T1-ESF 5. Line Code B8ZS 6. Line Mode DSU 7. Line Length (ft)/Tx Gain (dB) 0-133 8. Restore Time 1 second 9. Idle Code 7E A. Uplink Fail Alarm Behavior Cond. B. Signaling Mode CAS enable C. Cond. Data Pattern 7F D.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus Table E-13. T1 Configuration Parameters (Cont.) Parameter Possible Values Remarks Loopback State Internal Data received from the IP network side is looped back to the network transmit line. An unframed all ‘1’ code (AIS) is transmitted in the T1 Tx path toward the PBX. Incoming data from the PBX is ignored.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus Table E-13. T1 Configuration Parameters (Cont.) Parameter Possible Values Uplink Fail Alarm Behavior Cond AIS Remarks Selects notification by the agent TDM side if Ethernet link fails IPmux-1/1E sends a Cond.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus Table E-13. T1 Configuration Parameters (Cont.) Parameter Possible Values Remarks Cond. CAS first 2.5 sec Pattern 0 to F (ESF) 0 to 3 (D4) FF 2 or 4 Bit Code applied (during the first 2.5 seconds) to AB(D4) or ABCD (ESF) bits (relevant in CAS mode only) when fault conditions occur. After the first 2.5 seconds the code specified in ‘Cond. CAS (ABCD) pattern’ is applied.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus Table E-14.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus Analog Configuration Main Menu ↓ 2. Configuration (Analog) ↓ 2. Analog Configuration ANALOG CONFIGURATION 1. Clock Source Adaptive 2. Far End Type E1 3. Channel Configuration > 4. Signaling Profile Configuration > 5. Signaling Feedback 6. Signaling Mode 7. Wiring ESC.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus Analog Channel Configuration CHANNEL CONFIGURATION Main Menu ↓ 2. Configuration (Analog) ↓ 2. Analog Configuration ↓ 3. Channel Configuration 1. Channel Number 1 2. Channel Status Enable 3. Rx Gain -4dBm 4. Tx Gain 0dBm 5. Testing Disable 6. Echo Cancellation Status Disable ESC. Exit Select item from the menu. Figure E-29. Channel Configuration Menu Table E-17.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus Signaling Profile Configuration Main Menu SIGNALING PROFILE CONFIGURATION ↓ 2. Configuration (Analog) ↓ 2. Analog Configuration ↓ 4. Signaling Profile Configuration 1. Rx A A 2. Rx B N/C 3. Rx C N/C 4. Rx D N/C 5. Tx A A 6. Tx B 1 7. Tx C 0 8. Tx D 1 ESC. Exit +------------------------+ | Rx: From Network | | Tx: To Network | +------------------------+ Select item from the menu. Figure E-30.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus E.6 Connection Configuration: Static Mode Note Main Menu ↓ 2. Configuration ↓ 3. Connection Configuration The Connection Configuration menu changes according to the Connection Mode selection (item 1). This section describes Static mode. For Dynamic CAS mode and CESoIP mode, see separate descriptions later in this manual. To configure the Connection: 1. Select 1 to enter the Connection Mode.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus Bundle Connection Configuration: Static Mode BUNDLE CONNECTION CONFIGURATION Main Menu ↓ 2. Configuration ↓ 3. Connection Configuration ↓ 2. Bundle Connection Configuration 1. Bundle ID 1 2. IP TOS 1 3. TDM Bytes in Frame (x48 bytes) 1 4. Connection Status Disable 5. Destination IP Address 0.0.0.0 6. Next Hop 0.0.0.0 7. Destination Bundle 1 8.
Appendix E Configuration Menus TDM Bytes in Frame (x48 bytes) 1 to 30 IPmux-1/1E Installation and Operation Manual Allows you to set the UDP payload length – this parameter enables reduction of Ethernet throughput (detailed explanation in Chapter 1). Default payload: single payload (1) Table E-20. Bundle Connection Parameters: Static Mode (Cont.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus Protection Switching Configuration PROTECTION SWITCHING CONFIGURATION Main Menu ↓ 2. Configuration ↓ 3. Connection Configuration ↓ 5. Protection Switching Configuration 1. Primary Bundle ID Empty! 2. Secondary Bundle ID Empty! 3. Redundancy Type Empty! 4. TDM Fail Time Empty! 5. Event Threshold Window (sec) Empty! 6. Sequence Number Threshold (0=Disable) Empty! 7. Underflow/Overflow Threshold (0=Disable) Empty! 8.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus Table E-21. Protection Switching Configuration Parameters (Cont.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus Bundle Connection Configuration: Dynamic CAS Mode BUNDLE CONNECTION CONFIGURATION Main Menu ↓ 2. Configuration ↓ 3. Connection Configuration ↓ 2. Bundle Connection Configuration 1. Bundle ID 1 2. IP TOS 1 3. Active Time Slot Bytes in Frame 24 4. Connection Status Disable 5. Destination IP Address 0.0.0.0 6. Next Hop 0.0.0.0 7. Destination Bundle 1 8.
Appendix E Configuration Menus Active Time Slot Bytes in Frame 24 to 64 IPmux-1/1E Installation and Operation Manual Number of bytes, per active time slot, that will be sent in every fram transmitted over the Ethernet. The maximum value depends on the number of timeslots. Table E-22. Bundle Connection Parameters: Dynamic CAS Mode (Cont.) Parameter Possible Values Remarks Connection Status Enable Connection enabled Disable Frames will not be sent from this connection Destination IP Address 0.0.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus Activation Criterion Main Menu ↓ 2. Configuration ↓ 3. Connection Configuration ↓ 3. Activation Activation Criterion 1. Pattern ID 1 2. Tx A 1 3. Tx B N/C 4. Tx C N/C 5. Tx D N/C Criterion ESC. Exit D. Delete N. Next Figure E-36. Activation Criterion Menu Table E-23.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus Note For CESoIP: The E1/T1 Signaling Mode must be configured as CAS Disable or the Line Type configured as Unframed. To change the Connection Mode from Dynamic CAS to CESoIP: Change the Connection Mode to Static. Update the E1/T1 Signaling Mode or Line Type. Change the Connection Mode to CESoIP 2. Enter the Bundle Connection Configuration data (described later in this section). 3.
IPmux-1/1E Installation and Operation Manual Note Appendix E Configuration Menus • First define the bundle. • When changing the Destination IP Address, Next Hop, or Destination Bundle, the Connection Status must be set to Disable. After you save the changes, Connection Status can be reset to Enable. Table E-24.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus E.9 LAN Configuration (No User Port) Note When configuring two LANs, see Ethernet Configuration/Status . LAN CONFIGURATION Main Menu ↓ 2. Configuration ↓ 4. LAN Configuration 1. Auto Negotiation Enable 2. Max Capability advertised 100baseT Full Duplex 3. Default type 100baseT Full Duplex ESC. Exit Select item from the menu. Figure E-39.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus Table E-25.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus E.10 DS0 Bundle Configuration This configuration selects the timeslots to be transferred end-to-end for E1/T1 when the operation mode is Fractional or Fractional with CAS. One bundle of timeslots can be configured in the IPmux-1 TDMoIP link. Main Menu ↓ 2. Configuration ↓ 5. DS0 Bundle Configuration DS0 BUNDLE CONFIGURATION 1. Timeslot number 1-1 2. Timeslot Current Status SET 3. Echo Cancellation Status SET ESC.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus To save the change: • Type . IPmux-1 associates the new timeslot with the bundle. E.11 Performance Monitoring E1/T1 Statistics Main Menu ↓ 3. Performance Monitoring ↓ 1. E1/T1 Statistics E1 models only E1 STATISTICS E1 over UTP LOS: 0 LOF (Red): 0 LCV: 0 RAI (Yellow): 0 AIS: 0 FEBE: 0 BES: 0 DM: 0 ES: 0 SES: 0 UAS: 0 LOMF: 0 Time Since: sec 7------Valid Intervals 1. Interval ESC.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus Table E-27.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus Table E-27. E1/T1 Statistics (Cont.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus ISDN Statistics in IPmux-1 Main Menu ↓ 3. Performance Monitoring ↓ 1. ISDN Statistics ISDN STATISTICS ISDN-S over UTP LOF (Red): 0 ES: 0 SES: 0 UAS: 0 Time Since: 710 sec ------Valid Intervals 1. Interval Number 0 2. Channel Number 1/1 ESC. Exit 11---- N. Next Inv: Figure E-42. ISDN Statistics Menu Table E-29.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus Analog Status – IPmux-1E with FXS/FXO/E&M Main Menu ↓ 3. Performance Monitoring ↓ 1. Analog Status ANALOG STATUS Channel 1: ON HOOK Channel 2: ON HOOK Channel 3: ON HOOK Channel 4: ON HOOK ESC. Exit Figure E-43. Analog Status The options for each channel are: • On hook • Off hook • Ringing.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus LAN Status (no User port) Main Menu ↓ 3. Performance Monitoring ↓ 2.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus Table E-30. LAN Status (Cont.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus Bundle Connection Status /Statistics Main Menu ↓ 3. Performance Monitoring ↓ 3. Bundle Connection Status BUNDLE CONNECTION STATISTICS Sequence Errors: 0 Jitter Buffer Underflows: 0 Jitter Buffer Overflows: 0 MAX Jitter Buffer Deviation 300 Time Since: ESC. Exit 00 sec -------- valid intervals N. Next Inv Figure E-45. Bundle Connection Statistics Menu BUNDLE CONNECTION STATUS Bundle ID: Main Menu ↓ 3.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus Table E-31.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus E.12 Ethernet Configuration/Status – with Ethernet User Port This section illustrates and describes the menus for IPmux-1/1E when the Ethernet User port is present. General Information Main Menu ↓ 1. System Menu ↓ 1. General Information GENERAL INFORMATION Software Version Hardware Version Inventory No. Boot: HW: 0.0/1.0 232635 1.21 7-1-2001 08:35 Application: 3.00-D1 9-2-2001 16:55 Backup: 3.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus LAN Configuration LAN CONFIGURATION Main Menu ↓ 2. Configuration ↓ 4. Switch Configuration ↓ 1. LAN Configuration 1. Channel Network 2. Channel Status Enable 3. Auto Negotiation Enable 4. Max Capability advertised 100BaseT Full Duplex 5. Default type 100BaseT Full Duplex 6. VLAN Tagging Yes/No 7. Default VLAN 8. Rate limit (kbps) (0–Disable) 100 ESC. Exit N. Next Select item from the menu. Figure E-49.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus Table E-32.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus Erase MAC Table Main Menu ↓ 2. Configuration ↓ 4. Switch Configuration ↓ 3. Erase MAC Table The MAC table is erased automatically every time you change the general operating mode of the switch, or you remove a VLAN membership. To erase the MAC Table: x 1. On the Switch Configuration menu, select 3. A confirmation line appears. Traffic will be disrupted. Are you sure? Figure E-50. Erase MAC Table Confirmation 2.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus Table E-33. VLAN Configuration – User Tagged, User Untagged, Rate+User Untagged Modes Parameter Values Remarks VLAN ID 1 to 4094 Selects the VLAN to edit. Creates a VLAN entry if the VLAN does not exist.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus LAN STATUS Main Menu ↓ 3. Performance Monitoring ↓ 2. LAN Status Unit Mac Address 00-20-D2-16-3B-3D Mode Half duplex Rate(Mbps) 10 Status Not connected Frames received Total Frames: 0 Total Octets: 0 Oversize Frames: 0 Fragments: 0 Jabber: 0 Dropped Frames: 0 CRC Errors: 0 Frames transmitted Correct frames: 0 Correct Octets: 0 Collision: 0 Channel: Network/User1/Internal Esc. Exit R.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus LAN STATUS Mac Address 00-20-D2-16-3B-3D Mode Half duplex Rate(Mbps) 10 Status Not connected Frames received Total Frames: 0 Total Octets: 0 Frames transmitted Correct frames: 0 Correct Octets: 0 Channel: Internal Esc. Exit R. Reset Counters N. Next Channel Figure E-53. LAN Status Menu – Two Ethernet Ports (Internal) To reset counters: Type R.
IPmux-1/1E Installation and Operation Manual Appendix E Configuration Menus Table E-35.
Appendix E Configuration Menus E-58 Ethernet Configuration/Status – with Ethernet User Port IPmux-1/1E Installation and Operation Manual
Index —#— µ-Law, 1-12 —A— access rights, C-4 activation criterion, E-32, E-35, E-36 menu, E-35 Active Timeslots in this Bundle, E-40 adaptive, E-20 timing, 1-13 address secondary IP, E-28 Agent IP Address, D-2 Aging Time, E-50 AIS, 4-9, E-12, E-42 alarm buffer, 4-1 Alarm ID, E-11 alarms, E-12 alarm trap, E-10, E-11 alarm trap mask, E-11 end-to-end, 1-24 trap, E-9 A-Law, 1-12 Alignment Errors, 4-14, 4-18, E-47 AMI, E-21 Analog Configuration menu, E-25 Analog Status menu, E-45 analog voice, 1-34 ANSI V
Index Command, E-15 Command-Response Polling Protocol, C-1 community, C-3, E-10 Cond.
IPmux-1/1E Installation and Operation Manual fileName, D-2 fileServerIP, D-2 fileTransCmd, D-2 flash memory, A-1 Force Connection, E-32 fractional, 1-7 fractional operation (IPmux-1 E1/T1), 1-11 fractional with CAS operation (IPmux-1 E1/T1), 111 frame format, 1-16 frame structure Ethernet, 1-17 TDMoIP, 1-16 Index Intrinsic PDV, 1-20 IP Address, 1-6, E-8, E-49 Manager, E-11 secondary, E-28 IP Mask, E-8 mask, E-28 IP packets, 1-6 IP ToS, E-29, E-33, E-37 IPmux-1 indicators, 3-2 IPmux-1 (E1/T1) menu tree
Index LOMF, 4-11, E-43 loopbacks, E-18, E-21, E-24 E1/T1 External Loop, 4-25 E1/T1 Internal Loop, 4-25 ISDN External Loop, 4-26 ISDN Internal Loop, 4-26 remote in FXS, 4-26 tests, 4-25, 4-26 timing, 1-13 tone injection, 4-26 LOS, 4-8, E-12, E-42 —M— MAC Address, 4-14, 4-18, E-46, E-49, E-57 MAC table, E-53 Main menu, E-2 Main Menu, 3-12 Manage IP Address, E-11 managed objects, C-2 management, 1-5 Management Configuration menu, E-9 management domains, C-3 Management Information Base (MIB).
IPmux-1/1E Installation and Operation Manual exchange, A-3 operation modes E1 (IPmux-1 FXS/FXO/E&M), 1-12 fractional (IPmux-1 E1/T1), 1-11 fractional with CAS (IPmux-1 E1/T1), 1-11 NT (IPmux-1 ISDN BRI), 1-11 T1 D4 (IPmux-1 FXS/FXO/E&M), 1-12 T1 ESF (IPmux-1 FXS/FXO/E&M), 1-12 TE (IPmux-1 ISDN BRI), 1-11 unframed (IPmux-1 E1/T1), 1-11 operation modes - internal switch basic, 1-27 rate, 1-30 rate + user tagged, 1-31 rate + user untagged, 1-31 user tagged, 1-28 user untagged, 1-29 optical budget, 1-7 —P—
Index IPmux-1/1E Installation and Operation Manual static connection, 1-16 static mode, 1-10, 1-23 terminal-emulation, 3-4 Testing, E-26 tests, 1-13, 4-25 TFTP, E-15 TFTP downloading procedure, D-1 TFTP server, D-1 tftpRetryTimeOut, D-2 tftpTotalOut, D-2 Time/Date menu, E-13 Time/Date Update menu, E-13 timeout, E-13 Timeout static mode configuration timeslot, 1-12, E-40 timing, 1-8 environment, C-1 management domains under SNMP, C-3 operations, C-1 principles, C-1 software delete, A-3 download, A-1
DC Power Supply Connection – Terminal Block Connector Note: Ignore this supplement if the unit is AC-powered. Certain DC-powered units are equipped with a plastic 3-pin VDC-IN power input connector, located on the unit rear panel. Different variations of the connector are shown in Figure 1. All are functionally identical. Supplied with such units is a kit including a mating Terminal Block (TB) type connector plug for attaching to your power supply cable.
Note: Certain TB plugs are equipped with captive screws for securing the assembled cable’s TB plug to the unit’s VDC-IN connector (C and E types only). To secure the plug, tighten the two screws on the plug into the corresponding holes on the sides of the input connector as shown in Figure 3. Captive screws Figure 3. TB Plug with Captive Screws (optional) DC Power Supply Wire Voltage Polarity Refer to Figure 4 for proper mapping of the power supply wire leads to the TB plug’s three terminals.
IPmux-1/1E Installation and Operation Manual configuration, E-54 Configuration menu, E-53 ID, E-6, E-11, E-30, E-34, E-37 Priority, E-6, E-11, E-30, E-34, E-37 Tagging, E-11, E-30, E-34, E-37 Index —W— Wait-To-Restore Time, E-32 Wiring, E-25 Write, E-10 —X— XMODEM, E-13 I-7
Index I-8 IPmux-1/1E Installation and Operation Manual
24 Raoul Wallenberg St., Tel Aviv 69719, Israel Tel: +972-3-6458181, Fax: +972-3-6483331, +972-3-6498250 E-mail: erika_y@rad.com, Web site: www.rad.com Customer Response Form RAD Data Communications would like your help in improving its product documentation. Please complete and return this form by mail or by fax or send us an e-mail with your comments.
Error Report Type of Error(s) ❒ Incompatibility with product or Problem(s): ❒ Difficulty in understanding text ❒ Regulatory information (Safety, Compliance, Warnings, etc.) ❒ Difficulty in finding needed information ❒ Missing information ❒ Illogical flow of information ❒ Style (spelling, grammar, references, etc.) ❒ Appearance ❒ Other _________ Please list the exact page numbers with the error(s), detail the errors you found (information missing, unclear or inadequately explained, etc.
www.rad.com INTERNATIONAL HEADQUARTERS: 24 Raoul Wallenberg Street, Tel Aviv 69719, Israel, Tel: 972-3-6458181 Fax: 972-3-6498250, 972-3-6474436, Email: rad@rad.com U.S. HEADQUARTERS: 900 Corporate Drive, Mahwah, N.J. 07430, Tel: (201) 529-1100 Toll Free: 1-800-444-7234, Fax: (201) 529-5777, Email: market@radusa.com Publication No.
