CH A P T E R 3 MIB Specifications This chapter describes each Management Information Base (MIB) on the Cisco 7304 router. Each description lists any constraints about how the MIB is implemented on the Cisco 7304 router platform. Unless noted otherwise, the Cisco 7304 implementation of a MIB follows the standard. Any objects not listed in a table are implemented as defined in the MIB. For detailed MIB descriptions, see the MIB.
Chapter 3 Table 3-1 MIB Specifications Supported and Verified Cisco 7304 MIBs (continued) CISCO-ENTITY-FRU-CONTROL-MIB OLD-CISCO-CHASSIS-MIB CISCO-ENTITY-PFE -MIB OLD-CISCO-CPU-MIB CISCO-ENTITY-SENSOR-MIB OLD-CISCO-INTERFACES-MIB CISCO-ENTITY-VENDORTYPE-OID-MIB OLD-CISCO-IP-MIB CISCO-ENVMON-MIB OLD-CISCO-MEMORY-MIB CISCO-FLASH-MIB PIM-MIB (RFC 2934) CISCO-FRAME-RELAY-MIB RFC1213-MIB (MIB II) CISCO-FTP-CLIENT-MIB RFC1243-MIB (AppleTalk) CISCO-HSRP-EXT-MIB RFC1253-MIB (OSPF) CISCO-HSRP-M
Chapter 3 MIB Specifications ATM-MIB Table 3-2 Cisco 7304 Router MIBs—Support Not Verified in the c7304 Image (continued) CISCO-CAR-MIB MPOA-MIB CISCO-CASA-FA-MIB MSDP-MIB CISCO-CASA-MIB NOVELL-IPX-MIB CISCO-CIRCUIT-INTERFACE-MIB NOVELL-NLSP-MIB CISCO-DLCSW-MIB NOVELL-RIPSAP-MIB CISCO-DLSW-EXT-MIB OLD-CISCO-APPLETALK-MIB CISCO-DLSW-MIB OLD-CISCO-DECNET-MIB CISCO-DSPU-MIB OLD-CISCO-NOVELL-MIB CISCO-FRAS-HOST-MIB OLD-CISCO-SYSTEM-MIB CISCO-IETF-ATM2-PVCTRAP-MIB OLD-CISCO-TCP-MIB CISCO-
Chapter 3 MIB Specifications ATM-FORUM-ADDR-REG-MIB Table 3-3 lists the constraints that the Cisco 7304 router places on objects in the ATM-MIB. For detailed definitions of MIB objects, see the MIB. Table 3-3 ATM-MIB Constraints MIB Object Notes atmInterfaceDs3PlcpTable Not used in Cisco 7304. atmInterfaceTCTable Not supported. atmTrafficDescrParamTable Read-only. atmVplTable Not supported. atmVclTable • atmVclAdminStatus Read-only. • atmVclReceiveTrafficDescrIndex Read-only.
Chapter 3 MIB Specifications BGP4-MIB BGP4-MIB The BGP4-MIB (RFC 1657) provides access to information related to the implementation of the Border Gateway Protocol (BGP). The MIB provides: • BGP configuration information • Information about BGP peers and messages exchanged with them • Information about advertised networks BRIDGE-MIB The BRIDGE-MIB contains objects to manage Media Access Control (MAC) bridges between Local Area Network (LAN) segments, as defined by the IEEE 802.1D-1990 standard.
Chapter 3 MIB Specifications CISCO-ASPP-MIB CISCO-ASPP-MIB The CISCO-ASPP MIB provides configuration and operational information on asynchronous polled protocols such as the asynchronous security protocols that alarm-monitoring companies use. The protocols are handled in Pass-through mode. ASPP handles the receiving and sending of asynchronous blocks. CISCO-ATM-EXT-MIB The CISCO-ATM-EXT-MIB contains extensions to the Cisco ATM module that are used to manage ATM entities.
Chapter 3 MIB Specifications CISCO-BGP-POLICY-ACCOUNTING-MIB Table 3-4 CISCO-BCP-MIB Constraints (continued) MIB Object Notes • bcpConfigMacSupport Read-only. Possible values: enabled(1), disabled(2) • bcpConfigTinygram Read-only. Possible values: enabled(1), disabled(2) • bcpConfigMacAddressControl Read-only. Possible values: enabled(1), disabled(2) • bcpConfigSpanTreeControl Read-only. Possible values: enabled(1), disabled(2) • bcpConfigIeee802dot1qTagged Read-only.
Chapter 3 MIB Specifications CISCO-BSTUN-MIB CISCO-BSTUN-MIB The CISCO-BSTUN-MIB contains objects to manage Block Serial Tunnels (BSTUNs) on the router. The MIB provides global BSTUN information and contains configuration and operational information to manage BSTUN groups, ports, and routes. CISCO-BULK-FILE-MIB The CISCO-BULK-FILE-MIB contains objects to create and delete files of SNMP data for bulk-file transfer.
Chapter 3 MIB Specifications CISCO-CDP-MIB CISCO-CDP-MIB The CISCO-CDP-MIB contains objects to manage the Cisco Discovery Protocol (CDP) on the router. CISCO-CEF-MIB The CISCO-CEF-MIB (Cisco Express Forwarding) contains objects that manage Cisco Express Forwarding (CEF) technology. CEF is the key data plane forwarding path for layer 3 IP switching technology. The CISCO-CEF-MIB monitorS CEF operational data and provideS notification when encountering errors in CEF, through SNMP.
Chapter 3 MIB Specifications CISCO-CLASS-BASED-QOS-MIB feature have a separate statistics object. Run-time instances of QoS objects are each assigned a unique identifier (cbQosObjectsIndex) to distinguish among multiple objects with matching configurations.
Chapter 3 MIB Specifications CISCO-CLASS-BASED-QOS-MIB MIB Constraints Table 3-5 lists the constraints that the Cisco 7304 Network Service Engine (NSE) 100-based router places on objects in the CISCO-CLASS-BASED-QOS-MIB. For detailed definitions of MIB objects, see the MIB. Any MIB table or object not listed in this table is implemented as defined in the MIB. Note The CISCO-CLASS-BASED-QOS-MIB support for the Cisco 7304 NPE-G100 and the Cisco c7200 NPE-G1 is the same.
Chapter 3 MIB Specifications CISCO-CONFIG-COPY-MIB Table 3-5 CISCO-CLASS-BASED-QOS-MIB Constraints for the c7304 NSE-100 MIB Object • cbQosTSStatsDelayedPktOverflow • cbQosTSStatsDelayedPkt· • cbQosTSStatsDelayedPkt64 • cbQosTSStatsDropByteOverflow • cbQosTSStatsDropByte • cbQosTSStatsDropByte64 • cbQosTSStatsActive • cbQosTSStatsCurrentQSize Notes *PXF is Cisco Parallel eXpress Forwarding (PXF) IP Services Processor technology.
Chapter 3 MIB Specifications CISCO-DLSW-MIB CISCO-DLSW-MIB The CISCO-DLSW-MIB contains objects to manage data-link switches. CISCO-DSPU-MIB The CISCO-DSPU-MIB contains objects to configure and manage Cisco downstream physical unit (DSPU) objects. CISCO-ENTITY-ALARM-MIB The CISCO-ENTITY-ALARM-MIB enables the Cisco 7304 router to monitor alarms generated by system components, such as the chassis, slots, modules, power supplies, fans, and ports.
Chapter 3 MIB Specifications CISCO-ENTITY-ALARM-MIB • Physical entity—The component in the Cisco 7304 router that generates the alarm. • Physical vendor type—The object specifies an identifier (typically an enterprise-specific OID) that uniquely identifies the vendor type of those physical entities that this alarm description applies to.
Chapter 3 MIB Specifications CISCO-ENTITY-ALARM-MIB Table 3-8 lists the alarm descriptions and severity levels for the Cisco 7304 router physical entity, the 6-port clear channel T3 (DS3) line card.
Chapter 3 MIB Specifications CISCO-ENTITY-ALARM-MIB Table 3-10 lists the alarm descriptions and severity levels for the Cisco 7304 router physical entities, 2 and 4-port OC-3c/STM-1, and 1 and 2-port OC-12c/STM-4 Packet over SONET/SDH line cards.
Chapter 3 MIB Specifications CISCO-ENTITY-ALARM-MIB Table 3-10 entPhysicalTable Objects for Cisco 7304 Router Packet over SONET Line Card Ports Physical Entity entPhysicalVendor Type ceAlarmDescr Severity Packet over SONET cevPortPOS critical Path payload unequipped 19 Packet over SONET cevPortPOS critical Count of APS 20 Packet over SONET cevPortPOS critical Receiver data out of lock failure 21 Packet over SONET cevPortPOS critical Signal failure alarm 22 Packet over SONET cevPor
Chapter 3 MIB Specifications CISCO-ENTITY-ALARM-MIB Table 3-11 lists the alarm descriptions and severity levels for the Cisco 7304 router physical entities, 2-port OC-3 ATM line cards.
Chapter 3 MIB Specifications CISCO-ENTITY-ALARM-MIB Table 3-12 lists the alarm descriptions and severity levels for the Cisco 7304 router physical entities, 1-port enhanced ATM T3, and E3 port adapters.
Chapter 3 MIB Specifications CISCO-ENTITY-ASSET-MIB CISCO-ENTITY-ASSET-MIB The CISCO-ENTITY-ASSET-MIB provides asset tracking information for the physical components in the ENTITY-MIB (RFC 2737) entPhysicalTable. This MIB is applicable to all line and processor cards. The ceAssetTable contains an entry (ceAssetEntry) for each physical component on the router.
Chapter 3 MIB Specifications CISCO-ENTITY-FRU-CONTROL-MIB Table 3-14 CISCO-ENTITY-EXT-MIB Object Constraints MIB Object Notes ceExtConfigRegTable Note ceExtConfigRegNext Read only. ceExtSysBootImageList Read only. The CISCO-ENTITY-EXT-MIB is only supported for the physical entities representing active and standby processors.
Chapter 3 MIB Specifications CISCO-ENTITY-PFE-MIB Table 3-15 CISCO-ENTITY-FRU-CONTROL-MIB Constraints (continued) MIB Object • Notes cefcMaxDefaultInLinePower Not supported. 1 The entPhysicalEntry (which has module(9) as entPhysicalClass in the entPhysicalTable) has a corresponding entry in the cefcModuleTable. 2 Because port adapters do not provide operational status information, they cannot be administratively controlled and independently OIRed.
Chapter 3 MIB Specifications CISCO-ENTITY-VENDORTYPE-OID-MIB CISCO-ENTITY-VENDORTYPE-OID-MIB The CISCO-ENTITY-VENDORTYPE-OID-MIB defines the object identifiers (OIDs) assigned to various Cisco 7304 router components. The OIDs in this MIB are used by the entPhysicalTable of the ENTITY-MIB as values for the entPhysicalVendorType field in entPhysicalTable. Each OID uniquely identifies a type of physical entity, such as a chassis, line cards, or port adapters.
Chapter 3 MIB Specifications CISCO-ENTITY-VENDORTYPE-OID-MIB Table 3-17 CISCO-ENTITY-VENDORTYPE-OID-MIB Objects and Constraints (continued) MIB Object (OID Assignment) Notes (Part Number) • cevC73002Oc3PosSmLr (1.3.6.1.4.1.9.12.3.1.9.17.48) 2-port, single-mode long reach (7300-2OC-3POS-SML) • cevC73004Oc3PosMm (1.3.6.1.4.1.9.12.3.1.9.17.48) 4-port, multimode (7300-2OC-3POS-MM) • cevC73004Oc3PosSmIr (1.3.6.1.4.1.9.12.3.1.9.17.
Chapter 3 MIB Specifications CISCO-ENVMON-MIB Table 3-17 CISCO-ENTITY-VENDORTYPE-OID-MIB Objects and Constraints (continued) MIB Object (OID Assignment) Notes (Part Number) cevPort • cevPortFEIP (1.3.6.1.4.1.9.12.3.1.10.10) NSE Fast Ethernet port • cevPortGE (1.3.6.1.4.1.9.12.3.1.10.20) NSE GigabitEthernet port • cevPortGE (1.3.6.1.4.1.9.12.3.1.10.52) NPE GigabitEthernet port • cevPortOc3 (1.3.6.1.4.1.9.12.3.1.10.80) OC-3 ATM port • cevPortT3 (1.3.6.1.4.1.9.12.3.1.10.
Chapter 3 MIB Specifications CISCO-FLASH-MIB CISCO-FLASH-MIB The CISCO-FLASH-MIB contains objects to manage flash cards and flash-card operations. CISCO-FRAME-RELAY-MIB The CISCO-FRAME-RELAY-MIB contains Frame Relay information that is specific to Cisco products or that is missing from RFC 1315. CISCO-FRAS-HOST-MIB The CISCO-FRAS-HOST-MIB contains objects specific to upstream or host-end sessions.
Chapter 3 MIB Specifications CISCO-IETF-IP-FORWARD-MIB CISCO-IETF-IP-FORWARD-MIB The CISCO-IETF-IP-FORWARD-MIB contains objects to manage multipath IP routes in a classless interdomain routing (CIDR) environment. This MIB is based on the IETF document draft-ietf-ipngwg-rfc2096-update-00.txt. CISCO-IETF-IP-MIB The CISCO-IETF-IP-MIB contains objects to manage the Internet Protocol (IP), but not to manage IP routes. The MIB also contains objects to manage the Internet Control Message Protocol (ICMP).
Chapter 3 MIB Specifications CISCO-ENHANCED-MEMORY-POOL-MIB CISCO-ENHANCED-MEMORY-POOL-MIB Note The CISCO-ENHANCED-MEMORY-POOL-MIB is not supported in this release. The CISCO-ENHANCED-MEMORY-POOL-MIB (Table 3-18) contains objects to monitor memory pools on all physical entities on a managed system Memory utilization information is provided to users at three different intervals of time: 1 minute, 5 minutes, and 10 minutes.
Chapter 3 MIB Specifications CISCO-LEC-DATA-VCC-MIB CISCO-LEC-DATA-VCC-MIB The CISCO-LEC-DATA-VCC-MIB module is a Cisco extension to the ATM Forum's LANE Client MIB. This extension identifies those VCCs which are being used to carry packets sent on LANE Data Direct VCCs. CISCO-LEC-EXT-MIB The CISCO-LEC-EXT-MIB module is a Cisco extension to the ATM Forum's LANE client MIB. CISCO-LECS-MIB The CISCO-LECS-MIB contains objects that manage LANE configuration in Cisco devices.
Chapter 3 MIB Specifications CISCO-NETFLOW-MIB Table 3-19 CISCO-NETFLOW-MIB Object Groups Objects Group Description cnfCacheInfo Provides common information for all active/inactive flows ( i.e. entries, time out etc) per cache basis. cnfExportInfo Provides information about export like export version and export destinations(/Collectors). cnfFeatureAcceleration Provides information about NetFlow Feature Acceleration. cnfExportStatistics Provides export statistics.
Chapter 3 MIB Specifications CISCO-NDE-MIB CISCO-NDE-MIB The CISCO-NDE-MIB contains objects to configure and monitor the operation of the NetFlow Data Export (NDE) feature. A network flow is a unidirectional sequence of packets between a pair of source and destination endpoints, which are identified by IP address and transport layer application port number. NetFlow uses the IP protocol type, type of service (ToS), and input interface identifier to uniquely identify network flows.
Chapter 3 MIB Specifications CISCO-QLLC01-MIB CISCO-QLLC01-MIB The CISCO-QLLC01-MIB contains objects to configure and monitor logical connections for the Qualified Logical Link Control (QLLC) protocol. CISCO-QUEUE-MIB The CISCO-QUEUE-MIB contains objects to manage interface queues, which can be used for FIFO, priority, custom, and fair queuing.
Chapter 3 MIB Specifications CISCO-RTTMON-MIB MIB Constraints Table 3-20 lists the constraints that the Cisco 7304 router places on objects in the CISCO-RTTMON-MIB. For detailed definitions of MIB objects, see the MIB. Table 3-20 CISCO-RTTMON-MIB Constraints MIB Object Notes RttMonProtocol Not supported: rttMonApplAuthTable • snaRUEcho • snaLU0EchoAppl Not supported.
Chapter 3 MIB Specifications CISCO-SDLLC-MIB CISCO-SDLLC-MIB The CISCO-SDLLC-MIB contains object to manage SDLC Logical Link Control (SDLLC). The MIB contains read-only configuration and operational information for the Cisco implementation of Synchronous Data Link Control (SDLC) to Logical Link Control, type 2 (LLC2) media translation. CISCO-SLB-EXT-MIB The CISCO-SLB-EXT-MIB contains extensions to the Cisco server load-balancing MIB (CISCO-SLB-MIB).
Chapter 3 MIB Specifications CISCO-STUN-MIB CISCO-STUN-MIB The CISCO-STUN-MIB contains objects to configure and monitor serial tunneling (STUN) on the router. The MIB contains global STUN configuration and operational information, and objects to manage STUN groups, ports, and routes. CISCO-SYSLOG-MIB The CISCO-SYSLOG-MIB contains all system log messages generated by the Cisco IOS software. The MIB provides a way to access syslog messages through SNMP.
Chapter 3 MIB Specifications DLSW-MIB On the Cisco 7304 router, the MIB contains information about VLAN subinterfaces created on GigE WAN ports on the 4-port GigE WAN Optical Services Module (OSM-2+4GE-WAN+). The MIB maps each VLAN-ID to an ifIndex, which you can use to access the ipRouteTable to obtain the routing configuration for the routed VLAN interface. DLSW-MIB The DLSW-MIB (RFC 2024) contains objects to manage data-link switching (DLSw) on the router.
Chapter 3 MIB Specifications ENTITY-MIB The following are the five conformance groups contained in the Entity-MIB: • entityPhysical group—Describes the physical entities managed by a single agent. • entityLogical group—Describes the logical entities managed by a single agent. • entityMapping group—Describes the associations between the physical entities, logical entities, interfaces, and non-interface ports managed by a single agent.
Chapter 3 MIB Specifications ENTITY-MIB Table 3-22 lists entPhysicalTable entries for the Cisco 7304 router. Table 3-22 entPhysicalTable Entries for Cisco 7304 Chassis Components entPhysicalDescr entPhysicalVendorType entPhysicalClass entPhysicalName C7300 chassis cevChassis7304 chassis 7300 Chassis Chassis slot cevContainerSlot container(5) slot 0 Contained in the chassis Chassis slot cevContainerSlot container(5) slot 1 Contained in the chassis.
Chapter 3 MIB Specifications ENTITY-MIB Table 3-22 entPhysicalTable Entries for Cisco 7304 Chassis Components (continued) entPhysicalDescr entPhysicalVendorType entPhysicalClass entPhysicalName Fan module cevFanC7300Fan Module other Fan state cevSensorC7300PSFan sensor(8) State Notes Entity description — and PS slot number — Contained in the fan Table 3-23 lists entPhysicalTable entries for the Cisco 7304 router network service engine (NSE) cards.
Chapter 3 MIB Specifications ENTITY-MIB Table 3-23 entPhysicalTable Entries for Cisco 7304 Network Service Engine Cards (continued) entPhysicalDescr entPhysicalVendorType entPhysicalClass entPhysicalName Notes NSE DB 1.65 V sensor cevSensorC7300NseDb sensor(8) TempVoltage Entity description and slot number Contained in the primary NSE DB. NSE DB 1.8 V sensor cevSensorC7300NseDb sensor(8) TempVoltage Entity description and slot number Contained in the primary NSE DB.
Chapter 3 MIB Specifications ENTITY-MIB Table 3-25 lists entPhysicalTable entries for the Cisco 7304 Router OC-3-POS components.
Chapter 3 MIB Specifications ENTITY-MIB Table 3-26 lists entPhysicalTable entries for the Cisco 7304 router OC-12-POS components. Table 3-26 entPhysicalTable Entries for Cisco 7304 OC-12-POS Card Components entPhysicalDescr entPhysicalVendorType entPhysicalClass entPhysicalName Notes 1-port POS OC-12 cevC7300Oc12PosMm Multimode module(9) Entity description 1-port and slot number.
Chapter 3 MIB Specifications ENTITY-MIB Table 3-27 lists entPhysicalTable entries for the Cisco 7304 router OC-48-POS components.
Chapter 3 MIB Specifications ENTITY-MIB Table 3-28 lists entPhysicalTable entries for the Cisco 7304 Router modules, ports, and temperature sensors.
Chapter 3 MIB Specifications ENTITY-MIB Table 3-29 entPhysicalTable Entries for Cisco 7304 Router Temperature Sensor Components entPhysicalDescr entPhysicalVendorType entPhysicalClass entPhysicalName Notes Outlet 1.8 V Sensor cevSensorC7300Outlet TempVoltage sensor(8) Entity description Contained in and slot number Primary NSE-100 or primary NPE-G100* Outlet 2.
Chapter 3 MIB Specifications ENTITY-MIB Table 3-29 entPhysicalTable Entries for Cisco 7304 Router Temperature Sensor Components entPhysicalDescr entPhysicalVendorType entPhysicalClass entPhysicalName Hotspot 1.
Chapter 3 MIB Specifications ENTITY-MIB Table 3-31 lists entPhysicalTable entries for the Cisco 7304 router port adapter cards.
Chapter 3 MIB Specifications ETHERLIKE-MIB ETHERLIKE-MIB The ETHERLIKE-MIB (RFC 2665) contains objects to manage Ethernet-like interfaces on the Cisco 7304 router. MIB Constraints Table 3-32 lists the constraints that the Cisco 7304 router places on objects in the ETHERLIKE-MIB. Any objects not listed in this table are implemented as defined in the MIB. For detailed definitions of MIB objects, see the MIB.
Chapter 3 MIB Specifications HC-RMON-MIB HC-RMON-MIB The MIB module for managing remote monitoring device implementations. This MIB module augments the original RMON MIB as specified in RFC 1757 and RFC 1513 and RMON2 MIB as specified in RFC 2021. IEEE8021-PAE-MIB The Port Access Entity module for managing IEEE 802.1X. IEEE8023-LAG-MIB The IEEE 8023-LAG-MIB is the Link Aggregation module for managing IEEE Standard 802.3ad.
Chapter 3 MIB Specifications IF-MIB Table 3-35 ifTable Object Values and Constraints for OC-12 ATM OSM Cards OSM-2-OC-12-ATM SONET Layer ATM and ATM Subinterface Layer AAL5 and AAL5 Subinterface Layer IfDescr ATM slot/port ATM slot/port–ATM layer ATM slot/port.subif–ATM subif layer ATM slot/port–AAL5 layer ATM slot/port.subif–AAL5 subif layer IfType sonet(39) atm(37) atmSubInterface(134) aal5(49) IfMtu 4470 Not used. Not used.
Chapter 3 MIB Specifications IGMP-MIB Table 3-37 ifTable Object Values for DS3 Channelized T1/E1 OSMs OSM-12CT3-T1 DS3 Layer DS1 Layer IfDescr T3 slot/subslot/port E3 slot/subslot/port T1 slot/subslot/port E1 slot/subslot/port IfType ds3(30) ds1(18) IfSpeed 44736000 (DS3) 34368000 (E3) 1544000 (DS1) 2048000 (E1) IfPhysAddress The circuit ID value, or zero length The circuit ID value, or zero length string. string.
Chapter 3 MIB Specifications INT-SERV-GUARANTEED-MIB INT-SERV-GUARANTEED-MIB The INT-SERV-GUARANTEED-MIB describes the guaranteed service of the Integrated Services Protocol (ISP). INT-SERV-MIB The INT-SERV-MIB describes the Integrated Services Protocol (ISP). IPMROUTE-MIB The IPMROUTE-MIB contains objects to manage IP multicast routing on the router, independent of the actual multicast routing protocol in use.
Chapter 3 MIB Specifications MPLS-LDP-MIB MIB Constraints Table 3-39 lists the constraints that the Cisco 7304 router places on objects in the MPLS-LDP-MIB. For detailed definitions of MIB objects, see the MIB. Any object not listed in this table is implemented as defined in the MIB. Table 3-39 MPLS-LDP-MIB Constraints MIB Object Notes mplsLdpEntityTable • mplsLdpEntityProtocolVersion Read-only. • mplsLdpEntityAdminStatus Read-only. • mplsLdpEntityWellKnownDiscoveryPort Read-only.
Chapter 3 MIB Specifications MPLS-LDP-MIB Table 3-39 MPLS-LDP-MIB Constraints (continued) MIB Object Notes • mplsLdpEntityAtmLsrConnectivity Read-only. • mplsLdpEntityDefaultControlVpi Read-only. • mplsLdpEntityDefaultControlVci Read-only. • mplsLdpEntityUnlabTrafVpi Read-only. • mplsLdpEntityUnlabTrafVci Read-only. • mplsLdpEntityAtmStorageType Read-only. Value volatile(2) • mplsLdpEntityAtmRowStatus Read-only.
Chapter 3 MIB Specifications MPLS-LSR-MIB MPLS-LSR-MIB The MPLS-LSR-MIB provides configuration and performance monitoring information to manage label switched paths (LSPs) through a label switching router (LSR) that is using the Multiprotocol Label Switching (MPLS) technology. The router supports the IETF version of the MPLS-LSR-MIB. For detailed information about this MIB, see its feature module description at the following URL: http://www.cisco.
Chapter 3 MIB Specifications MPLS-LSR-MIB Table 3-40 MPLS-LSR-MIB Constraints (continued) MIB Object Notes • mplsInSegmentPackets Read-only. Always 0. • mplsInSegmentHCOctets Read-only. Always 0. • mplsInSegmentErrors Read-only. Always 0. • mplsInSegmentDiscards Read-only. Always 0. • mplsInSegmentPerforDiscontinuityTime Read-only. Always 0. mplsOutSegmentTable • mplsOutSegmentIfIndex Read-only. • mplsOutSegmentPushTopLabel Read-only. • mplsOutSegmentTopLabel Read-only.
Chapter 3 MIB Specifications MPLS-TE-MIB Table 3-40 MPLS-LSR-MIB Constraints (continued) MIB Object Notes • mplsXCIndexNext, Read-only. • mplsLabelStackIndexNext Read-only. • mplsTrafficParamIndexNext Read-only. mplsLabelStackTable Not supported. mplsTrafficParamTable • mplsInSegmentTrapEnable Read-only. • mplsOutSegmentTrapEnable Read-only. • mplsXCTrapEnable Read-only. • mplsXCUp *Not supported. • mplsXCDown *Not supported. • mplsInSegmentUp *Not supported.
Chapter 3 MIB Specifications MPLS-TE-MIB MIB Constraints Table 3-41 lists the constraints that the Cisco 7304 router places on objects in the MPLS-TE-MIB. For detailed definitions of MIB objects, see the MIB. Any objects not listed in this table are implemented as defined in the MIB. Table 3-41 MPLS-TE-MIB Constraints MIB Object Notes mplsTunnelIndexNext Always 0. mplsTunnelTable • mplsTunnelName Read-only. • mplsTunnelDescr Read-only. • mplsTunnelIsIf Read-only.
Chapter 3 MIB Specifications MPLS-VPN-MIB Table 3-41 MPLS-TE-MIB Constraints (continued) MIB Object Notes • mplsTunnelHopIpv6PrefixLen Read-only. • mplsTunnelHopAsNumber Read-only. • mplsTunnelHopLspId Read-only. • mplsTunnelHopType Read-only. • mplsTunnelHopRowStatus Read-only. Always active(1). • mplsTunnelHopStorageType Read-only. Volatile(2). Always active. mplsTunnelResourceIndexNext Read-only. Always 0. mplsTunnelResourceTable • mplsTunnelResourceMaxRate Read-only.
Chapter 3 MIB Specifications MPLS-VPN-MIB MIB Constraints Table 3-42 lists the constraints that the Cisco 7304 router places on objects in the MPLS-VPN-MIB. For detailed definitions of MIB objects, see the MIB. Any objects not listed in the table are implemented as defined in the MIB. Table 3-42 MPLS-VPN-MIB Constraints MIB Object Notes MplsNumVrfSecViolationThreshExceeded Not supported. mplsVpnVrfSecTable • MplsVpnVrfSecIllegalLabelViolations Read-only. Always 0.
Chapter 3 MIB Specifications MSDP-MIB Table 3-42 MPLS-VPN-MIB Constraints (continued) MIB Object Notes • MplsVpnVrfRouteTargetDescr Description of the route target. This object is not supported in this Cisco IOS release. Therefore, the object is the same as mplsVpnVrfRouteTarget. • MplsVpnVrfRouteDistinguisher Read-only. • MplsVpnVrfRouteNextHopAS Read-only. Value always 0. • MplsVpnVrfRouteRowStatus Read-only.
Chapter 3 MIB Specifications NOVELL-IPX-MIB • Refine the MIB logs by using the SNMP SET operation on objects which enable control over log sizes. This control can be executed on a global basis (affecting the whole Notification Log MIB database) or on a per named log basis. • Specify the maximum time a notification can remain logged in the Notification Log MIB.
Chapter 3 MIB Specifications NOVELL-RIPSAP-MIB NOVELL-RIPSAP-MIB The NOVELL-RIPSAP-MIB defines the management information for the RIP and SAP protocols running in an IPX environment. It provides information in addition to that contained in the IPX MIB itself. This MIB is virtually identical to the RIPSAP MIB distributed as a part of the Novell NetWare Link Services Protocol (NLSP) Specification 1.0, Novell Part Number 100-001708-002, 2nd Edition Feb '94.
Chapter 3 MIB Specifications OLD-CISCO-CPU-MIB OLD-CISCO-CPU-MIB The OLD-CISCO-CPU-MIB describes CPU usage and active system processes on devices running an earlier implementation of the Cisco IOS operating system. OLD-CISCO-DECNET-MIB The OLD-CISCO-DECNET-MIB provides information about the implementation of DECnet on the router.
Chapter 3 MIB Specifications OLD-CISCO-TCP-MIB OLD-CISCO-TCP-MIB Starting with Cisco IOS software Release 10.2, all objects defined in this MIB have been deprecated. They have been replaced with the objects defined in the CISCO-TCP-MIB.my document. Management applications should no longer examine the objects defined in this MIB. OLD-CISCO-TS-MIB The OLD-CISCO-TS-MIB provides information about the number of terminal lines and virtual lines on this device.
Chapter 3 MIB Specifications RFC1243-MIB RFC1243-MIB The RFC1243-MIB uses the extended OBJECT-TYPE macro as defined in llapEntry 9 (9). The total number of times this LocalTalk interface received a lapRTS packet and expected a data packet, but did not receive any data packet. RFC1253-MIB The RFC1253-MIB contains objects to manage Version 2 of the Open Shortest Path First (OSPF) protocol.
Chapter 3 MIB Specifications RFC1407-MIB (DS3) RFC1407-MIB (DS3) The RFC1407-MIB (DS3-MIB) provides access to configuration and performance monitoring information for DS1 controllers and interfaces. MIB Constraints Table 3-38 on page 3-51 lists the constraints that the Cisco 7304 router places on objects in the RFC1407-MIB. For detailed definitions of MIB objects, see the MIB. Any other object not listed in the table is implemented as defined in the RFC1407-MIB.
Chapter 3 MIB Specifications SMON-MIB SMON-MIB The SMON-MIB manages remote monitoring device implementations for Switched Networks. Identifies the source of the data that the associated function is configured to analyze. This Textual Convention extends the DataSource Textual Convention defined by RMON 2 to the following data source types: • ifIndex • smonVlanDataSource • entPhysicalEntry SNA-SDLC-MIB The SNA-SDLC-MIB contains objects that manage SDLC (synchronous data link control) devices.
Chapter 3 MIB Specifications SNMP-TARGET-MIB SNMP-TARGET-MIB The SNMP-TARGET-MIB (RFC 2573) contains objects to remotely configure the parameters used by an entity to generate SNMP notifications. The MIB defines the addresses of entities to send SNMP notifications to, and contains a list of tag values that are used to filter the notifications sent to these entities (see the SNMP-NOTIFICATION-MIB). There are no constraints on this MIB.
Chapter 3 MIB Specifications SOURCE-ROUTING-MIB MIB Constraints Table 3-46 lists the constraints that the Cisco 7304 router places on objects in the SONET-MIB. Any other objects not listed in the table are defined as in the RFC1595-MIB definition. For detailed definitions of MIB objects, see the MIB. Table 3-46 SONET-MIB Constraints MIB Object Notes sonetPathCurrentTable • sonetPathCurrentWidth Read-only. sonetVTCurrentTable Not supported. sonetVTIntervalTable Not supported.
