Cisco 10008 Router Hardware Installation Guide June 2006 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
C O N T E N T S Preface vii Document Version History Audience Purpose vii viii viii Document Organization viii Document Conventions viii Notes and Cautions ix Safety Warnings ix Related Documentation xi Obtaining Documentation xi Cisco.
Contents Disposing of the PRE CHAPTER 2 Preparing for Installation 1-11 2-1 Site Planning 2-1 Cisco Professional Installation 2-2 Site Selection Guidelines 2-2 Site Environmental Requirements 2-2 Heat Dissipation 2-2 Physical Characteristics 2-3 Floor Loading Considerations 2-3 Site Power Requirements 2-3 Electrical Service Requirements 2-4 Electrical Circuit Requirements 2-4 Site Cabling Guidelines 2-5 Interference Considerations 2-6 Asynchronous Terminal Connections 2-6 Ethernet Connections 2-6 Set
Contents Non-Rack Installation 3-11 Connecting the Chassis to Ground 3-13 Recommended Tools and Supplies 3-14 Attaching the Grounding Cable 3-14 Connecting DC Power to the Cisco 10008 Router Recommended Tools and Supplies 3-18 3-17 Connecting AC Power to the Cisco 10008 Router 3-22 Connecting Alarm Indicators 3-26 Connecting a Video Terminal to the PRE Console Port 3-30 Connecting Network Management and Signal System Cables 3-32 Ethernet Network Management Cable Connections 3-32 Connecting to a 1
Contents Troubleshooting the Console Port Serial Connection CHAPTER Maintaining the Cisco 10008 Router 5 Required Maintenance Tools Shutting Down the System 4-14 5-1 5-3 5-3 Backing Up the PCMCIA Card 5-3 Removing and Replacing Field-Replaceable Units 5-3 Front Cover Procedures 5-4 Removing the Front Cover 5-4 Replacing the Front Cover 5-6 Replacing the Air Filter 5-7 Replacing an Air Filter in a Chassis that Uses a Filter Tray 5-7 Replacing an Air Filter in a Chassis with Release Tabs 5-9 Replac
Preface This preface describes the audience, purpose, organization, and conventions used in the Cisco 10008 Router Hardware Installation Guide. There is also a list of related documents and instructions for obtaining technical assistance and additional information. Document Version History This is the first version of this document with an online part number. The document version history beginning with this online part number is in Table 1.
Preface Audience Audience To use this guide, you should be familiar not only with Cisco router hardware and cabling, but also with electronic circuitry and wiring practices. You should be able to perform basic network configuration procedures, and preferably have experience as an electronic or electromechanical technician. Purpose This installation guide explains the initial hardware installation and basic configuration procedures for the Cisco 10008 router.
Preface Document Conventions For example, the prompt router> indicates that you should be at the user level, and the prompt router# indicates that you should be at the privileged level. Access to the privileged level usually requires a password. Refer to the related software configuration and reference documentation for additional information. • Commands and key names words are in bold text. • Arguments for which you supply values are in italic text. • Optional elements appear in square brackets [ ].
Preface Document Conventions . Warning Means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. To see translations of the warnings that appear in this publication, refer to the Regulatory Compliance and Safety Information document that accompanied this device. Statement 1071 Waarschuwing Dit waarschuwingssymbool betekent gevaar.
Preface Related Documentation Aviso ¡Advertencia! Varning! Este símbolo de aviso indica perigo. Encontra-se numa situação que lhe poderá causar danos físicos. Antes de começar a trabalhar com qualquer equipamento, familiarize-se com os perigos relacionados com circuitos eléctricos, e com quaisquer práticas comuns que possam prevenir possíveis acidentes.
Preface Documentation Feedback Ordering Documentation You can find instructions for ordering documentation at this URL: http://www.cisco.com/univercd/cc/td/doc/es_inpck/pdi.htm You can order Cisco documentation in these ways: • Registered Cisco.com users (Cisco direct customers) can order Cisco product documentation from the Ordering tool: http://www.cisco.com/en/US/partner/ordering/index.shtml • Nonregistered Cisco.
Preface Obtaining Technical Assistance Note Use the Cisco Product Identification (CPI) tool to locate your product serial number before submitting a web or phone request for service. You can access the CPI tool from the Cisco Technical Support Website by clicking the Tools & Resources link under Documentation & Tools. Choose Cisco Product Identification Tool from the Alphabetical Index drop-down list, or click the Cisco Product Identification Tool link under Alerts & RMAs.
Preface Obtaining Additional Publications and Information Obtaining Additional Publications and Information Information about Cisco products, technologies, and network solutions is available from various online and printed sources. • Cisco Marketplace provides a variety of Cisco books, reference guides, and logo merchandise. Visit Cisco Marketplace, the company store, at this URL: http://www.cisco.
C H A P T E R 1 Cisco 10008 Router Overview The Cisco 10008 router is a high capacity Layer 3 router optimized to support selected Cisco IOS software services at wire speed performance on thousands of DS1/T1 connections. Designed primarily for use in a telco central office environment, it provides interfaces that connect to large numbers of subscribers using low-speed circuits, and then funnels all of that subscriber traffic into a small number of high-speed trunk interfaces.
Chapter 1 Cisco 10008 Router Overview Cisco 10008 Router Features Performance routing engine redundancy in the Cisco 10008 router is achieved through an implementation of Enhanced High System Availability (EHSA). This feature lets you configure the chassis for non-redundant operation with one PRE, or for redundant operation with two PREs.
Chapter 1 Cisco 10008 Router Overview Cisco 10008 Router Software Cisco 10008 Router Software Software is stored on the PRE which includes two PCMCIA slots that are accessible from the front panel. Either slot can store an Cisco IOS image or configuration file. The flash memory present on Cisco 10000 router line cards is used to store a simple ROM monitor/boot loader. The loader executes following a system reset, line card reset, or line card insertion.
Chapter 1 Cisco 10008 Router Overview Cisco 10008 Router Hardware Description Figure 1-1 Cisco 10008 Router Chassis—Front View 1 FANS OK FAN FAILURE MULTIFAN FAILURE When hot CAUTION removal swapping this fan be done and replaceme tray, system in under two nt must shutdown minu will occutes or r.
Chapter 1 Cisco 10008 Router Overview Cisco 10008 Router Hardware Description Figure 1-2 BNC Connectors on the Rear of the Chassis 1 Tx 2 Tx 0 RX 4 3 0 0 6 Tx RX RX Tx 1 1 Tx RX RX Tx 2 2 7 Tx RX RX Tx 3 3 Tx RX RX Tx 4 4 Tx RX RX Tx 5 5 Tx RX RX Tx 6 6 8 Tx RX RX Tx 7 7 Tx RX 126111 RX 5 1 Line card slot 8 5 Line card slot 1 2 Line cards slot 5 6 Power supply 3 Blower module 7 Half-height line card subslot 0 4 Line card slot 4 8 Half-height lin
Chapter 1 Cisco 10008 Router Overview Cisco 10008 Router Hardware Description The Cisco 10008 chassis is designed for mounting in 19-inch or (optional) 23-inch equipment racks, and contains the following components: • Blower Module, page 1-6 • Power Entry Modules, page 1-6 • Connector Ports, page 1-9 • PCMCIA Card Slots, page 1-10 Blower Module The Cisco 10008 router uses a blower module (Figure 1-3) containing four fans to supply cooling air to the chassis.
Chapter 1 Cisco 10008 Router Overview Cisco 10008 Router Hardware Description DC PEM 30003 Figure 1-4 POWER FAULT MISWIR E Table 1-1 DC PEM LEDs LED Description Power (green) PEM is powered on and is operational. Fault (yellow) The PEM is not operating correctly (see the Cisco 10000 Series ESR Troubleshooting Guide). Miswire (yellow) –48V and RTN (+) wires are reversed (see the “Troubleshooting Installation Problems” section on page 4-12).
Chapter 1 Cisco 10008 Router Overview Cisco 10008 Router Hardware Description AC PEM 30004 Figure 1-5 POWER FAULT Table 1-2 AC PEM LEDs LED Description Power (green) PEM is powered on and is operational. Fault (yellow) The PEM is not operating correctly (see the Cisco 10000 Series ESR Troubleshooting Guide). Line Card and PRE Module Compartment The module compartment has 10 slots: the two central slots are reserved for PRE modules, and the remaining 8 slots accommodate full-height line cards.
Chapter 1 Cisco 10008 Router Overview Cisco 10008 Router Hardware Description Each PXF ASIC has 32 independent processors that work on per-packet feature processing, yielding high throughput while still allowing substantial feature processing. The PXF centralizes packet processing in the PRE, which frees up space on line cards, enabling high interface density, yet retaining a compact form factor. Caution Although the PRE module supports hot-swapping, one PRE is required for the system to operate.
Chapter 1 Cisco 10008 Router Overview Cisco 10008 Router Hardware Description PCMCIA Card Slots Two PCMCIA Type II card slots can store the Cisco IOS image or a system configuration file on a flash memory card. The system can also boot from the software stored on the flash memory card. See “Figure 5-47Removing the PCMCIA Flash Card” section on page 5-45 for more information about inserting and removing flash cards from the PRE.
Chapter 1 Cisco 10008 Router Overview Cisco 10008 Router Hardware Description Table 1-3 LEDs and Cutoff Switch LEDs/Switch Status Description Status Green PRE is ready. Off No power to the PRE. Off The PRE is operating properly. Yellow A major failure has disabled the PRE. Fail Alphanumeric Display The small alphanumeric display on the front panel provides information on the state of the PRE. The display consists of two four-character LED panels.
Chapter 1 Cisco 10008 Router Overview Cisco 10008 Router Hardware Description Cisco 10008 Router Hardware Installation Guide 1-12 OL-0659-13
C H A P T E R 2 Preparing for Installation Before you install the Cisco 10008 router, consider: • The power and cabling requirements that must be in place at your installation site • The equipment required to install the router • The environmental conditions your installation site must meet to maintain normal operation This chapter guides you through the process of preparing for your router installation. Do not unpack the system until you are ready to install it.
Chapter 2 Preparing for Installation Site Planning Cisco Professional Installation Professional installation of the Cisco 10008 router is available through the Cisco Professional Services group. This includes advance site planning, configuring the router to your requirements, and testing the installed system. For more information about professional installation, talk to your Cisco sales representative. Site Selection Guidelines The Cisco 10008 router requires specific environmental operating conditions.
Chapter 2 Preparing for Installation Site Planning Table 2-2 Heat Dissipation of Cisco 10000 Series Router Chassis Type Heat Dissipation Cisco 10008 4770 Btu/hr Physical Characteristics Be familiar with the physical characteristics of the Cisco 10008 router to assist you in placing the system in the proper location. Table 2-3 shows the weight and dimensions of the Cisco 10008 router chassis. Table 2-3 Physical Characteristics of Cisco 10000 Series Router Characteristic Cisco 10008 Height 21.
Chapter 2 Preparing for Installation Site Planning Note The Cisco 10008 router installation must comply with all applicable codes and is approved for use with copper conductors only. The ground bond fastening hardware should be of compatible material and preclude loosening, deterioration, and electrochemical corrosion of hardware and joined material. Attachment of the chassis ground to a central office or other interior ground system should be made with a 6-AWG, copper ground conductor at a minimum.
Chapter 2 Preparing for Installation Site Planning DC Powered Systems The DC PEMs for the Cisco 10008 router chassis are not shipped with wiring to connect to the DC source. Both systems have terminal blocks to attach building’s input, return, and earthing (ground) wiring. The DC power source must comply with the Safety Extra Low Voltage (SELV) requirements in IEC 60950 based safety standards.
Chapter 2 Preparing for Installation Site Planning Interference Considerations When wires are run for any significant distance in an electromagnetic field, interference can occur between the field and the signals on the wires. This fact has two implications for the construction of plant wiring: Note • Bad wiring practice can result in radio interference emanating from the plant wiring.
Chapter 2 Preparing for Installation Site Planning Table 2-4 Signal Type Ethernet and Fast Ethernet Maximum Transmission Distances Transceiver Speed Cable Type Transmission Mode IEEE Maximum Distance Between Stations 10BaseT Ethernet 10 Mbps Category 3 twisted-pair Full and half duplex 328 ft (100 m) 100BaseT Fast Ethernet 100 Mbps Category 5 twisted-pair Full and half duplex 328 ft (100 m) Setting Up Fiber-Optic Connections For other fiber-optic specifications, see the Cisco 10000 Series
Chapter 2 Preparing for Installation Site Planning The electromagnetic pulse (EMP) generated by lightning or other high-energy phenomena can couple enough energy into unshielded conductors to damage or destroy electronic equipment. If you have previously experienced such problems, you should consult with RFI/EMI experts to ensure that you have adequate electrical surge suppression and shielding of signal cables in your Cisco 10008 series router operating environment.
Chapter 2 Preparing for Installation Site Planning Rack Placement Guidelines The placement of the rack can affect personnel safety, system maintenance, and the system’s ability to operate within the environmental characteristics described in Table 2-1 on page 2-2. Choose a proper location for the Cisco 10000 series router by following the guidelines below.
Chapter 2 Preparing for Installation Site Planning The Cisco 10008 chassis draws cooling air in through the intake vent in the front and moves the air across the internal components and out the exhaust vents on the top rear of the chassis, as illustrated in Figure 2-1.
Chapter 2 Preparing for Installation Safety Site Planning Checklist Table 2-5 is provided to help you perform and account for all the site planning tasks presented in this appendix. Table 2-5 Site Planning Checklist Site Planning Requirements The site meets the environmental requirements (Site Environmental Requirements, page 2-2). The site’s air conditioning system can compensate for the heat dissipation of the Cisco 10000 series (Heat Dissipation, page 2-2).
Chapter 2 Preparing for Installation Preventing Electrostatic Discharge Damage Warning • Never attempt to lift an object that might be too heavy to lift safely by yourself. • Always unplug the power cable before you install or remove a chassis. • Keep the chassis area clear and as dust free as possible during and after installation. • Keep tools and chassis components away from walk areas.
Chapter 2 Preparing for Installation Electrical Safety Caution For safety, periodically check the resistance value of the antistatic strap. The measurement should be between 1 and 10 megohms.
Chapter 2 Preparing for Installation Electrical Safety • Use caution when installing or modifying telephone lines. Warning Do not work on the system or connect or disconnect cables during periods of lightning activity. Statement 1001 Warning Before you work on equipment that is connected to power lines, remove jewelry (including rings, necklaces, and watches). Metal objects will heat up when connected to power and ground and the heat can cause serious burns or weld the metal object to the terminals.
Chapter 2 Preparing for Installation Chassis-Lifting Guidelines After you receive the Cisco 10008 router, we recommend that you have three people available to help with the installation and ensure safe lifting. Chassis-Lifting Guidelines The fully configured system weighs approximately 130 pounds. The chassis is not intended to be moved frequently.
Chapter 2 Preparing for Installation Required Tools and Equipment Step 2 With the other hand, grasp the top rear of the chassis under the air exhaust and carefully lift the chassis as shown in Figure 2-4. Required Tools and Equipment The tools and equipment listed below are recommended as the minimum necessary to install the Cisco 10008 router. You may need additional tools and equipment to install associated equipment and cables.
C H A P T E R 3 Installing the Cisco 10008 Router This chapter describes the procedures for installing the Cisco 10008 router on a tabletop or in equipment racks. It also describes how to connect interface and power cables, the proper way to power on the system, and installation troubleshooting procedures. Note The illustrations in this guide depict the original Cisco 10008 chassis. Your chassis may appear or look slightly different, but the installation procedure is the same.
Chapter 3 Installing the Cisco 10008 Router Rack-Mounting the Chassis If you are installing the chassis on an equipment shelf, on a tabletop, or using mounting hardware other than that supplied with the chassis, then go to the “Non-Rack Installation” section on page 3-11. Rack-Mounting the Chassis Rack-mounting the chassis is the preferred method of installation for the Cisco 10008 router.
Chapter 3 Installing the Cisco 10008 Router Rack-Mounting the Chassis Flush-Mounting in a 19-Inch Rack The Cisco 10008 chassis can be flush-mounted in a 19-inch equipment rack using the rack-mounting kit provided with your system.
Chapter 3 Installing the Cisco 10008 Router Rack-Mounting the Chassis Step 1 (Optional) Install a shelf in the rack to support the Cisco 10008 chassis. If you use a shelf, you can perform the installation with only two people. Step 2 (Optional) Remove the blower module and the PEMs to make the chassis easier to lift. Step 3 Lift the chassis into position between the rack posts (requires two people).
Chapter 3 Installing the Cisco 10008 Router Rack-Mounting the Chassis Center-Mounting in a 19-Inch Rack The Cisco 10008 chassis can be center-mounted in a 19-inch equipment rack using the rack-mounting kit provided with your system. The rack-mounting kit contains • Two mounting brackets • One cable management bracket • Mounting screws When handling the chassis, always follow proper lifting practices as outlined in the “Electrical Safety” section on page 2-13.
Chapter 3 Installing the Cisco 10008 Router Rack-Mounting the Chassis Step 1 Attach the two mounting brackets to the chassis so the flanges are positioned at the center of the chassis (Figure 3-3). Figure 3-4 Attaching Chassis to Equipment Rack FANS OK FAN FAILURE MULTIFAN FAILURE When hot CAUTION removal swapping this fan be done and replacem tray, system in under two ent must shutdown minu will occutes or r.
Chapter 3 Installing the Cisco 10008 Router Rack-Mounting the Chassis Figure 3-5 Attaching Cable Management Bracket FANS OK FAN FAILURE MULTIFAN FAILURE When hot CAUTION removal swapping this fan be done and replaceme tray, system in under two nt must shutdown minut will occures or .
Chapter 3 Installing the Cisco 10008 Router Rack-Mounting the Chassis Use the following procedure to flush-mount the Cisco 10008 chassis in a 23-inch equipment rack: Figure 3-6 Attaching Mounting Brackets to Chassis FANS OK FAN FAILURE MULTIFAN FAILURE When hot CAUTION removal swapping this fan be done and replaceme tray, system in under two nt must shutdown minu will occutes or r.
Chapter 3 Installing the Cisco 10008 Router Rack-Mounting the Chassis Figure 3-7 Attaching 23-inch Bracket Adapters FANS OK FAN FAILURE MULTIFAN FAILURE When hot CAUTION removal swapping this fan be done and replacem tray, system in under two ent must shutdown minu will occutes or r.
Chapter 3 Installing the Cisco 10008 Router Rack-Mounting the Chassis Figure 3-8 Attaching Chassis to Equipment Rack FANS OK FAN FAILURE MULTIFAN FAILURE When hot CAUTION removal swapping this fan be done and replacem tray, system in under two ent must shutdown minu will occutes or r.
Chapter 3 Installing the Cisco 10008 Router Non-Rack Installation Figure 3-9 Attaching the Cable Management Bracket FANS OK FAN FAILURE MULTIFAN FAILURE When hot CAUTION removal swapping this fan be done and replacemen tray, t must system in under two shutdown minut will occures or .
Chapter 3 Installing the Cisco 10008 Router Non-Rack Installation When installing the Cisco 10008 router on a workbench or tabletop, ensure that the surface is clean and that you have considered the following: • The Cisco 10008 router requires at least 3 inches (7.62 cm) of clearance at the inlet and exhaust vents (the front and top/rear sides of the chassis). • The Cisco 10008 router should be installed off the floor.
Chapter 3 Installing the Cisco 10008 Router Connecting the Chassis to Ground Note The cable management bracket consists of two pieces (the cable guide and channel), and is shipped assembled. If you want to use the cable guide only, you can remove the channel by loosening the captive screws before attaching the cable guide to the chassis.
Chapter 3 Installing the Cisco 10008 Router Connecting the Chassis to Ground Recommended Tools and Supplies Table 3-1 lists the tools, equipment, and supplies necessary to connect the system ground to the chassis. Table 3-1 Tools and Supplies Quantity Description 1 Number 2 Phillips screwdriver — 1 Wire stripping tool — 1 Crimping tool Must fit diameter of grounding lugs. 2 2-hole grounding lugs Recommended types: Must fit no. 6 stranded, no. 6 weld, or 37/24 flex cables.
Chapter 3 Installing the Cisco 10008 Router Connecting the Chassis to Ground Figure 3-12 Setting PEM Switches to the Off Position FANS OK FAN FAILUR E MULTI FAN FAILUR E When hot CAUTION removal swapping this fan be done and replacement tray, must system in under two shutdo wn will minutes or occur.
Chapter 3 Installing the Cisco 10008 Router Connecting the Chassis to Ground Connecting Grounding Lug to Chassis 132825 Figure 3-14 1 1 Step 4 Threaded grounding holes (2) Attach the grounding lug firmly to threaded holes at the bottom rear of the chassis using two M5 screws (Figure 3-14). Figure 3-15 Attaching the Grounding Wire to the Grounding Lug 132826 0.75 in.
Chapter 3 Installing the Cisco 10008 Router Connecting DC Power to the Cisco 10008 Router Step 6 Insert the stripped end of the grounding wire into the open end of a grounding lug and crimp the grounding lug securely to the wire (see Figure 3-15). Step 7 Attach the grounding lug to an appropriate grounding point at your site.
Chapter 3 Installing the Cisco 10008 Router Connecting DC Power to the Cisco 10008 Router Recommended Tools and Supplies Table 3-2 lists the tools and supplies that you need to connect the Cisco 10008 router to DC power sources. Table 3-2 Tools and Supplies Quantity Description 1 Flat-blade screwdriver — 1 Wire stripping tool — 2 or 4 (length varies) 10 AWG (minimum) wire cables 2 Tie wraps Comments Cables must reach from the Cisco 10008 router to the DC power source.
Chapter 3 Installing the Cisco 10008 Router Connecting DC Power to the Cisco 10008 Router Removing the Safety Cover 30023 Figure 3-17 Step 2 Loosen the captive screw on the rear safety cover and tilt the cover back (Figure 3-17).
Chapter 3 Installing the Cisco 10008 Router Connecting DC Power to the Cisco 10008 Router Removing the Rear Cover 30023 Figure 3-18 Step 3 Remove the safety cover by lifting it up and out from the chassis (Figure 3-18). Figure 3-19 Stripping Insulation 14747 10 mm max Step 4 Strip not more than 0.4 inches (10 mm) of insulation off the ends of the DC power leads (Figure 3-19).
Chapter 3 Installing the Cisco 10008 Router Connecting DC Power to the Cisco 10008 Router Figure 3-20 DC Power Connections RTN (+ ) – 48/– 60 V DC terminal block A RTN (+ ) DC terminal block B 30024 – 48/– 60 V Step 5 Connect the DC power lead from the first external power source to the DC terminal block A labeled –48V (Figure 3-20). Step 6 Connect the return wire (RTN) to terminal block A labeled RTN (+) (see Figure 3-20). • If you have redundant DC power, continue with Step 7.
Chapter 3 Installing the Cisco 10008 Router Connecting AC Power to the Cisco 10008 Router DC Power Cables Exiting Safety Cover 30025 Figure 3-21 Step 11 Replace the rear safety cover, making sure that the power wires exit through the holes on the side of the cover (Figure 3-21). Step 12 Go to the “Connecting a Video Terminal to the PRE Console Port” section on page 3-30 to continue the installation.
Chapter 3 Installing the Cisco 10008 Router Connecting AC Power to the Cisco 10008 Router There are five styles of AC-input power supply power cords available (differing in plug type); make sure you have the correct style for your site (see Table 3-3, Figure 3-22, and Figure 3-23.) All AC-input power supply power cords measure 14 feet (4.3 m). Cisco recommends that you: • Install an uninterruptible power source where possible.
Chapter 3 Installing the Cisco 10008 Router Connecting AC Power to the Cisco 10008 Router Table 3-4 AC Power Cord Options Plug (Facility End of Cord) Receptacle (Router End of Cord) Product Number Label Description North American 250 VAC, 60 Hz AC NEMA L6-20, power cord 20A IEC 320-C19 CAB-AC-6CK-TWL K Japanese 100 VAC, 50/60 Hz AC power cord IEC 320-C19 CAB-DS-ACJ-TWLK North American 120 VAC, 60 Hz AC NEMA 5-20P, power cord 20A IEC 320-C19 CAB-DS-120VAC Australian 240 VAC, 50 Hz AC AS 31
Chapter 3 Installing the Cisco 10008 Router Connecting AC Power to the Cisco 10008 Router Figure 3-24 Setting AC PEM Switch to the Off Position FANS OK FAN FAILUR E MULTI FAN FAILUR E When hot CAUTION removal swapping this fan be done and replacement tray, must system in under two shutdo wn will minutes or occur.
Chapter 3 Installing the Cisco 10008 Router Connecting Alarm Indicators Figure 3-25 AC Power Cord Connectors in Strain Relief Devices 1 FANS OK FAN FAILUR E MULTI FAN FAILUR E When hot CAUTION removal swapping this fan be done and replacement tray, must system in under two shutdo wn will minutes or occur.
Chapter 3 Installing the Cisco 10008 Router Connecting Alarm Indicators Removing the Safety Cover 30022 Figure 3-26 Use the following procedure to connect an alarm indicator to the system: Step 1 Loosen the captive screw on the rear safety cover and tilt the cover back (Figure 3-26).
Chapter 3 Installing the Cisco 10008 Router Connecting Alarm Indicators Removing the Rear Cover 30023 Figure 3-27 Step 2 Remove the safety cover by lifting it up and out from the chassis (Figure 3-27). Figure 3-28 Stripping Insulation 14747 10 mm max Step 3 Strip not more than 0.4 inches (10 mm) of insulation off the ends of the alarm indicator wire (Figure 3-28). Step 4 Connect one set of alarm indicator wires to the alarm terminal block as follows (see Figure 3-29): Caution a.
Chapter 3 Installing the Cisco 10008 Router Connecting Alarm Indicators Figure 3-29 Alarm Terminal Block Connections ALARMS 50VA SELV max NC COM MINOR NO NC COM MAJOR NO 32694 NC COM CRITICAL NO Step 5 Repeat steps 3 and 4 for any remaining alarm indicators. Step 6 Secure the power cabling to the chassis by feeding a tie wrap through the slot on the side of the chassis and binding the wires (see blowout in Figure 3-30).
Chapter 3 Installing the Cisco 10008 Router Connecting a Video Terminal to the PRE Console Port Alarm Indicator Wires Exiting Safety Cover 32693 Figure 3-30 Step 8 Go to the “Connecting a Video Terminal to the PRE Console Port” section on page 3-30 to continue the installation. Connecting a Video Terminal to the PRE Console Port The Cisco 10008 router PRE module has an asynchronous serial (EIA/TIA-232) RJ-45 console port labeled CON on its front panel.
Chapter 3 Installing the Cisco 10008 Router Connecting a Video Terminal to the PRE Console Port Figure 3-31 Console Port Connection on the PRE Module CISCO 10000 C O AU LI E N O LE X N K TH N E K R N E T 30027 1 OT 0 OT SL SL LI S Step 1 Connect one end of the RJ-45 crossover cable to the serial RJ-45 port (CON) on the PRE module (Figure 3-31).
Chapter 3 Installing the Cisco 10008 Router Connecting Network Management and Signal System Cables Step 6 Go to the “Connecting Network Management and Signal System Cables” section on page 3-32 to continue the installation. Connecting Network Management and Signal System Cables The Cisco 10008 router has connections to both the internal Ethernet management network and the external data network.
Chapter 3 Installing the Cisco 10008 Router Connecting Network Management and Signal System Cables Figure 3-33 Connecting 10BASE-T to Ethernet Port CISCO 10000 C O AU LI E N O LE X N K TH N E K R N E T 30036 1 OT 0 OT SL SL LI S Step 1 Connect one end of the Ethernet cable to the RJ-45 port on the primary PRE, labeled ETH (Figure 3-33).
Chapter 3 Installing the Cisco 10008 Router Connecting Network Management and Signal System Cables Caution • The wire connected to the left-most pin (pin 1) on one connector should be the same color as the wire connected to the left-most pin on the other connector. • The same rule applies to pins 2 through 8 on each connector. The color of the wire attached to a pin on one connector should match the color of the wire attached to the corresponding pin on the other connector.
Chapter 3 Installing the Cisco 10008 Router Connecting Network Management and Signal System Cables Auxiliary Modem Connection This asynchronous EIA/TIA-232 serial port is used to connect a modem to the PRE for remote administrative access. Use the following procedure to connect the Cisco 10008 router to a modem.
Chapter 3 Installing the Cisco 10008 Router Connecting Network Management and Signal System Cables Cisco 10008 Router Hardware Installation Guide 3-36 OL-0659-13
C H A P T E R 4 Starting and Configuring the Router This chapter provides information on powering on the system, basic file system information, and installation troubleshooting procedures.
Chapter 4 Starting and Configuring the Router Configuring the Cisco 10008 Router at Startup Figure 4-1 Cisco 10008 Router DC PEM Power Switches FANS OK FAN FAILUR E MULTI FAN FAILUR E When hot CAUTION removal swapping this fan be done and replacement tray, must system in under two shutdo wn will minutes or occur.
Chapter 4 Starting and Configuring the Router Configuring the Cisco 10008 Router at Startup Startup Display When you power on your Cisco 10008 router or execute the reload command, the console screen displays a message similar to the following: Restricted Rights Legend Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.
Chapter 4 Starting and Configuring the Router Configuring the Cisco 10008 Router at Startup Using the System Configuration Dialog Use the System Configuration Dialog to help you perform a basic configuration. Proceed through the dialog by answering questions and then pressing the Enter key. In most cases, you can get additional information by entering a question mark (?). Throughout the dialog, default values are shown in square brackets [ ].
Chapter 4 Starting and Configuring the Router Configuring the Cisco 10008 Router at Startup Community string [public]: public After you respond to the SNMP questions, the setup script lists the interfaces. For example: Interface IP-Address OK? Method Status Protocol Ethernet0/0/0 unassigned YES unset up up FastEthernet0/0/0 unassigned NO unset up up Interfaces that are not okay (OK? = NO) do not have a valid configuration.
Chapter 4 Starting and Configuring the Router Formatting Flash Memory Cards and Disks Step 16 The setup script concludes by giving you the choice to exit without saving, start the setup script, or save the configuration file: [0] Go to the IOS command prompt without saving this config. [1] Return back to the setup without saving this config. [2] Save this configuration to nvram and exit.
Chapter 4 Starting and Configuring the Router Managing the File Systems Step 3 Enter the format diskn: command at the privileged EXEC mode prompt to format the disk. The following example shows the display after you enter the format disk0: command: Router# format disk0: All sectors will be erased, proceed? [confirm] Enter volume id (up to 30 characters): MyNewdisk Formatting sector 1 Format device slot0 completed Router# The Flash memory disk is now ready for use.
Chapter 4 Starting and Configuring the Router Managing the File Systems You can use the privileged EXEC commands dir, del, and copy to manage the contents of the file systems. You can also use the commands mkdir and rmdir to create and remove directories on Flash disks. You cannot use the commands squeeze and undelete on Flash disks. For more information, refer to the Cisco IOS Configuration Fundamentals Configuration Guide.
Chapter 4 Starting and Configuring the Router Managing System Boot Parameters Relocating the Configuration to a Flash Disk To run the startup configuration off a Flash disk, use the following commands beginning in privileged EXEC mode: Step 1 Copy the current startup configuration to a new location. In the following example, the configuration file is copied from a TFTP server to a Flash disk in slot 0: Router# copy tftp://172.16.2.
Chapter 4 Starting and Configuring the Router Managing System Boot Parameters Changing the Configuration Register Settings To change the configuration register settings while you are running system software, perform the following steps: Step 1 From global configuration mode, enter the config-register value command to set the contents of the software configuration register; value is a hexadecimal number preceded by 0x.
Chapter 4 Starting and Configuring the Router Predeployment Testing Table 4-2 Definition of Bits in the Software Configuration Register Bit No. Hex Value Meaning/Function 00 to 03 0x0000 to 0x000F Defines the source of a default Cisco IOS software image required to run the router: • 00—At power-on, the system remains at the ROM monitor prompt (rommon>), awaiting a user command to boot the system manually by means of the rommon boot command.
Chapter 4 Starting and Configuring the Router Troubleshooting Installation Problems Troubleshooting Installation Problems This section contains general troubleshooting information to help you solve any problems you might encounter during the installation of the system. For any problems not covered in this section and for more detailed troubleshooting information, see the Cisco 10000 Series Router Troubleshooting Guide.
Chapter 4 Starting and Configuring the Router Troubleshooting Installation Problems Table 4-3 General Troubleshooting Tips (continued) Symptom Steps to Take You cannot establish a console or Telnet connection to the system. For information about troubleshooting Ethernet connections, see the “Troubleshooting Ethernet Connections” section on page 4-13.
Chapter 4 Starting and Configuring the Router Troubleshooting Installation Problems • If the LNK LED is on (green), but the Ethernet port does not seem to be working properly, make sure that the port in question is configured properly and is not administratively shut down. If you have a working console connection, perform the following steps: – At the router prompt, enter show int fast0/0/0.
C H A P T E R 5 Maintaining the Cisco 10008 Router The Cisco 10008 router is configured to your order and ready for installation when it arrives. After you install the system, you may have to perform specific maintenance procedures to ensure the router is operating properly. These procedures can include routine maintenance such as replacing the filter, upgrading system components, or replacing components with field replaceable units (FRUs).
Chapter 5 Maintaining the Cisco 10008 Router 38546 Situational Analysis Spare Parts Service providers usually draw on their own experience with similar equipment as they try to determine the number of spare parts of a given item to keep on hand. In developing a strategy for spare parts, the service providers must • Evaluate the criticality of the equipment. • Estimate the mean time between failures, a key component of any spares strategy.
Chapter 5 Maintaining the Cisco 10008 Router Required Maintenance Tools Required Maintenance Tools The only tools required to perform the maintenance procedures described in this chapter are: • A Number 2 Phillips screwdriver • A flat-blade screwdriver • An electrostatic discharge (ESD) grounding strap Shutting Down the System Although most components in the Cisco 10008 router are hot-swappable, you may have to shut down the system under certain circumstances.
Chapter 5 Maintaining the Cisco 10008 Router Removing and Replacing Field-Replaceable Units Front Cover Procedures The original Cisco 10008 router is equipped with a plastic front cover that ensures proper air flow through the system and protects the cables and connectors from damage. The following procedures describe how to remove and replace the front cover. Note Your router may not have a front cover. Only the original Cisco 10008 chassis was equipped with a plastic front cover.
Chapter 5 Maintaining the Cisco 10008 Router Removing and Replacing Field-Replaceable Units Figure 5-2 Removing the Front Cover FANS OK FAN FAILURE MULTIFAN FAILURE When hot CAUTION removal swapping this fan be done and replaceme tray, system in under two nt must shutdown minut will occures or .
Chapter 5 Maintaining the Cisco 10008 Router Removing and Replacing Field-Replaceable Units Replacing the Front Cover Use the following procedure to replace the front cover on the chassis: Figure 5-3 Attaching the Cover to the Chassis FANS OK FAN FAILURE MULTIFAN FAILURE When hot CAUTION removal swapping this fan be done and replaceme tray, system in under two nt must shutdown minut will occures or .
Chapter 5 Maintaining the Cisco 10008 Router Removing and Replacing Field-Replaceable Units Replacing the Air Filter If the air filter is dirty or clogged, the blower module could have a problem providing sufficient cooling air flow throughout the chassis, causing the system to overheat. To prevent a potential overheating problem, you should replace the air filter every 6 months. In certain environments where the air quality is poor, you may have to replace the filter more frequently.
Chapter 5 Maintaining the Cisco 10008 Router Removing and Replacing Field-Replaceable Units Figure 5-6 Removing the Air Filter 5 5 5 5 5 6XCT3–DS0 6XCT3–DS0 S TA TU S FA IL C R IT IC A M L A JO R M IN O R 6XCT3–DS0 FAULT MISWIR E AC O OC–12/STM–4 POS SM–IR C R IT IC A M L A JO R M IN O R PERFORMANCE ROUTING ENGINE 6XCT3–DS0 6XCT3–DS0 POWER PERFORMANCE ROUTING ENGINE CH OC-12-DSO SM-IR GIGABIT ETHERNET AC O S TA TU S FA IL 32220 PROC ESSOR ONLY Step 5 Pull out the filter tray far
Chapter 5 Maintaining the Cisco 10008 Router Removing and Replacing Field-Replaceable Units Replacing an Air Filter in a Chassis with Release Tabs Use the following procedure to remove and replace the air filter in a chassis that uses release tabs to hold the filter in place: Figure 5-8 Air Filter Release Tabs 5 5 5 5 5 OC–12/STM–4 POS SM–IR 6XCT3–DS0 6XCT3–DS0 C R IT IC A M L A JO R M IN O R 6XCT3–DS0 S TA TU S FA IL AC O PERFORMANCE ROUTING ENGINE POWER FAULT MISWIR E C R IT IC A M L A JO R
Chapter 5 Maintaining the Cisco 10008 Router Removing and Replacing Field-Replaceable Units Note The directional arrows located on the metal frame of the filter should point up (see enlargement in Figure 5-9). Replacing the Blower Module Use the following procedure to replace a blower module. The blower module supports hot-swapping (for up to 2 minutes) and can be replaced without interruption to system operation.
Chapter 5 Maintaining the Cisco 10008 Router Removing and Replacing Field-Replaceable Units Figure 5-11 Removing the Blower Module 1 FAN FAILURE MULTIFAN FAILURE When hot CAUTION removal swapping this fan be done and replaceme tray, system in under two nt must shutdown minu will occutes or r.
Chapter 5 Maintaining the Cisco 10008 Router Removing and Replacing Field-Replaceable Units Figure 5-13 Blower Module Cable Connector 132835 1 1 Blower module connector Step 5 Tighten the captive screws on each side of the blower module (see Figure 5-12). Step 6 Rerun all interface cables through the cable management brackets. Step 7 Replace the front cover if necessary (see the “Replacing the Front Cover” section on page 5-6).
Chapter 5 Maintaining the Cisco 10008 Router Removing and Replacing Field-Replaceable Units Figure 5-14 Removing the Blank Cover FANS OK FAN FAILURE MULTIFAN FAILURE When hot CAUTION removal swapping this fan be done and replacem tray, system in under two ent must shutdow minu n will occutes or r.
Chapter 5 Maintaining the Cisco 10008 Router Removing and Replacing Field-Replaceable Units Figure 5-15 Installing a DC PEM FANS OK FAN FAILURE MULTIFAN FAILURE When hot CAUTION removal swapping this fan be done and replacem tray, system in under two ent must shutdow minu n will occutes or r.
Chapter 5 Maintaining the Cisco 10008 Router Removing and Replacing Field-Replaceable Units Loosening the Captive Screw 30022 Figure 5-16 Step 4 Loosen the captive screw on the rear safety cover and tilt back the cover (Figure 5-16).
Chapter 5 Maintaining the Cisco 10008 Router Removing and Replacing Field-Replaceable Units Removing the Safety Cover 30023 Figure 5-17 Step 5 Remove the safety cover by lifting it up and out from the chassis (Figure 5-17).
Chapter 5 Maintaining the Cisco 10008 Router Removing and Replacing Field-Replaceable Units Figure 5-18 DC Power Connection RTN (+ ) 1 1 Step 6 132830 – 48/– 60 V DC terminal block B Connect the DC PEM power leads: • Connect the DC power lead from the external power source to the DC terminal block B labeled –48V (Figure 5-18). • Connect the return wire (RTN) to terminal block B labeled RTN (+) (Figure 5-18).
Chapter 5 Maintaining the Cisco 10008 Router Removing and Replacing Field-Replaceable Units Securing DC Power Cables to the Chassis 30025 Figure 5-19 Step 7 Secure the power cabling to the chassis by feeding a tie wrap through the slot on the side of the chassis and binding the cables (Figure 5-19). Step 8 Replace the rear safety cover, making sure that the power cables exit through the holes on the side of the cover (Figure 5-19).
Chapter 5 Maintaining the Cisco 10008 Router Removing and Replacing Field-Replaceable Units Figure 5-20 Setting DC Power Switch to the On Position FANS OK FAN FAILUR E MULTI FAN FAILUR E When hot CAUTION removal swapping this fan be done and replacement tray, must system in under two shutdo wn will minutes or occur.
Chapter 5 Maintaining the Cisco 10008 Router Removing and Replacing Field-Replaceable Units Replacing a DC PEM Use the following procedure to replace a DC PEM: Figure 5-21 Setting DC Power Switch to the Off Position FANS OK FAN FAILUR E MULTI FAN FAILUR E When hot CAUTION removal swapping this fan be done and replacement tray, must system in under two shutdo wn will minutes or occur.
Chapter 5 Maintaining the Cisco 10008 Router Removing and Replacing Field-Replaceable Units Figure 5-22 Removing a DC PEM FANS OK FAN FAILURE MULTIFAN FAILURE When hot CAUTION removal swapping this fan be done and replacem tray, system in under two ent must shutdow minu n will occutes or r.
Chapter 5 Maintaining the Cisco 10008 Router Removing and Replacing Field-Replaceable Units Figure 5-23 Installing a DC PEM FANS OK FAN FAILURE MULTIFAN FAILURE When hot CAUTION removal swapping this fan be done and replacem tray, system in under two ent must shutdow minu n will occutes or r.
Chapter 5 Maintaining the Cisco 10008 Router Removing and Replacing Field-Replaceable Units Figure 5-24 Setting DC Power Switch to the On Position FANS OK FAN FAILUR E MULTI FAN FAILUR E When hot CAUTION removal swapping this fan be done and replacement tray, must system in under two shutdo wn will minutes or occur.
Chapter 5 Maintaining the Cisco 10008 Router Removing and Replacing Field-Replaceable Units Installing a Second AC PEM Use the following procedure to install a second AC PEM in the bottom power bay for redundancy: Figure 5-25 Removing the Blank Cover FANS OK FAN FAILURE MULTIFAN FAILURE When hot CAUTION removal swapping this fan be done and replacem tray, system in under two ent must shutdow minu n will occutes or r.
Chapter 5 Maintaining the Cisco 10008 Router Removing and Replacing Field-Replaceable Units Figure 5-26 Installing an AC PEM FANS OK FAN FAILURE MULTIFAN FAILURE When hot CAUTION removal swapping this fan be done and replacem tray, system in under two ent must shutdow minu n will occutes or r.
Chapter 5 Maintaining the Cisco 10008 Router Removing and Replacing Field-Replaceable Units Figure 5-27 AC Power Cord Connectors in Strain Relief Devices 1 FANS OK FAN FAILUR E MULTI FAN FAILUR E When hot CAUTION removal swapping this fan be done and replacement tray, must system in under two shutdo wn will minutes or occur.
Chapter 5 Maintaining the Cisco 10008 Router Removing and Replacing Field-Replaceable Units Figure 5-28 Setting the AC Power Switch to the On Position FANS OK FAN FAILUR E MULTI FAN FAILUR E When hot CAUTION removal swapping this fan be done and replacement tray, must system in under two shutdo wn will minutes or occur.
Chapter 5 Maintaining the Cisco 10008 Router Removing and Replacing Field-Replaceable Units Replacing an AC PEM Use the following procedure to replace an AC PEM: Figure 5-29 Setting AC Power Switch to the Off Position FANS OK FAN FAILUR E MULTI FAN FAILUR E When hot CAUTION removal swapping this fan be done and replacement tray, must system in under two shutdo wn will minutes or occur.
Chapter 5 Maintaining the Cisco 10008 Router Removing and Replacing Field-Replaceable Units Figure 5-30 Removing an AC PEM FANS OK FAN FAILURE MULTIFAN FAILURE When hot CAUTION removal swapping this fan be done and replacem tray, system in under two ent must shutdow minu n will occutes or r.
Chapter 5 Maintaining the Cisco 10008 Router Removing and Replacing Field-Replaceable Units Figure 5-31 Installing an AC PEM FANS OK FAN FAILURE MULTIFAN FAILURE When hot CAUTION removal swapping this fan be done and replacem tray, system in under two ent must shutdow minu n will occutes or r.
Chapter 5 Maintaining the Cisco 10008 Router Removing and Replacing Field-Replaceable Units Figure 5-32 AC Power Cord Connectors in Canoes 1 FANS OK FAN FAILUR E MULTI FAN FAILUR E When hot CAUTION removal swapping this fan be done and replacement tray, must system in under two shutdo wn will minutes or occur.
Chapter 5 Maintaining the Cisco 10008 Router Connecting Alarm Indicators Figure 5-33 Setting AC Power Switch to the On Position FANS OK FAN FAILUR E MULTI FAN FAILUR E When hot CAUTION removal swapping this fan be done and replacement tray, must system in under two shutdo wn will minutes or occur.
Chapter 5 Maintaining the Cisco 10008 Router Connecting Alarm Indicators Removing the Safety Cover 30022 Figure 5-34 Step 1 Set the AC or DC PEM power switches to the off (0) position. Step 2 Loosen the captive screw on the rear safety cover and tilt the cover back (Figure 5-34).
Chapter 5 Maintaining the Cisco 10008 Router Connecting Alarm Indicators Removing the Rear Cover 30023 Figure 5-35 Step 3 Remove the safety cover by lifting it up and out from the chassis (Figure 5-35). Figure 5-36 Stripping Insulation 14747 10 mm max Step 4 Strip not more than 0.4 inches (10 mm) of insulation off of the ends of the alarm indicator wire (Figure 5-36).
Chapter 5 Maintaining the Cisco 10008 Router Connecting Alarm Indicators Figure 5-37 Alarm Terminal Block Connections ALARMS 50VA SELV max NC COM MINOR NO NC COM MAJOR NO 32694 NC COM CRITICAL NO Step 5 Caution Step 6 Connect one set of alarm indicator wires to the alarm terminal block as follows: a. Connect one lead to the common (COM) terminal (Figure 5-37). b. Connect the other lead to the normally closed (NC) or normally open (NO) terminal.
Chapter 5 Maintaining the Cisco 10008 Router Connecting Alarm Indicators Alarm Indicator Wires Exiting Safety Cover 32693 Figure 5-38 Step 7 Secure the power cabling to the chassis by feeding a tie wrap through the slot on the side of the chassis and binding the cables (see blowout in Figure 5-38). Step 8 Replace the rear safety cover, making sure that the alarm indicator wires exit through the holes on the side of the cover (Figure 5-38).
Chapter 5 Maintaining the Cisco 10008 Router Connecting Alarm Indicators Figure 5-39 ESD Chassis Connection 5 5 5 5 CISCO 10000 5 SL SL S 0 U T AT IL O ST FA T O 0 S U AT IL ST FA BIT S BIT S OC–12/STM–4 POS SM–IR 6XCT3–DS0 6XCT3–DS0 6XCT3–DS0 FA IL P/N ESR-PRE3 P/N ESR-PRE3 PERFORMANCE ROUTING ENGINE PERFORMANCE ROUTING ENGINE 6XCT3–DS0 6XCT3–DS0 CH OC-12-DSO SM-IR POWER FAULT MISWIR E 126144 PROC ESSOR ONLY 1 1 ESD socket Step 1 Remove the front cover if necessary (see Fro
Chapter 5 Maintaining the Cisco 10008 Router Connecting Alarm Indicators Figure 5-40 Loosening the Captive Screws FANS OK FAN FAILURE MULTIFAN FAILURE When hot CAUTION removal swapping this fan be done and replacem tray, system in under two ent must shutdow minu n will occutes or r.
Chapter 5 Maintaining the Cisco 10008 Router Connecting Alarm Indicators Figure 5-41 Opening the Ejector Levers FANS OK FAN FAILURE MULTIFAN FAILURE When hot CAUTION removal swapping this fan be done and replaceme tray, system in under two nt must shutdown minu will occutes or r.
Chapter 5 Maintaining the Cisco 10008 Router Connecting Alarm Indicators Figure 5-42 Removing the PRE FANS OK FAN FAILURE MULTIFAN FAILURE When hot CAUTION removal swapping this fan be done and replacem tray, system in under two ent must shutdow minu n will occutes or r.
Chapter 5 Maintaining the Cisco 10008 Router Connecting Alarm Indicators Figure 5-43 Inserting the PRE 1 OT 0 T LO SL LIN RN E K T 1 2 1 2 K LIN Y IT TIV AC POWER FAULT MISWIR E ALARM 1 S C R 2 2 O M R IN R IT O R OP M R LO IE AR RX C AL TX RR AJ AL M IC 3 CA NK LI S 2 IT 3 ALARM 3 AC O 4 3 O AJ AL M IC 4 M R 3 IN O R O 4 5 RX 4 TX R RIE CAR AC 4 5 5 5 5 SL T O 0 S U AT IL ST FA SL BIT B OC–12/STM–4 POS SM–IR S IL 6XCT3–DS0 TA
Chapter 5 Maintaining the Cisco 10008 Router Connecting Alarm Indicators Closing the Ejector Levers T3–DS0 POS SM–IR 0 DS0 Step 10 P/N ESR-PRE3 P/N ESR-PRE3 E ROUTING ENGINE OUTING ENGINE PROC ESSO R ONLY PROC ESSOR ONLY 32683 Figure 5-44 Simultaneously pivot both ejector levers toward each other (until they are parallel to the faceplate) to firmly seat the PRE in the backplane (Figure 5-44). The PRE cycles through its power-on self-test.
Chapter 5 Maintaining the Cisco 10008 Router Connecting Alarm Indicators Figure 5-45 Tightening Captive Screws FANS OK FAN FAILURE MULTIFAN FAILURE When hot CAUTION removal swapping this fan be done and replacem tray, system in under two ent must shutdow minu n will occutes or r.
Chapter 5 Maintaining the Cisco 10008 Router Connecting Alarm Indicators Removing and Installing a PCMCIA Flash Memory Card Use the following procedure to remove and install a PCMCIA flash memory card: Note For information about formatting Flash memory cards and disks, see the “Formatting Flash Memory Cards and Disks” section on page 4-6. Step 1 Remove the front cover if necessary (see Front Cover Procedures, page 5-4).
Chapter 5 Maintaining the Cisco 10008 Router Connecting Alarm Indicators Figure 5-47 Removing the PCMCIA Flash Card CISCO 10000 C O AU AC E N O LE X TI TH N V E IT R Y N K E T 32690 1 OT 0 OT SL SL LI S Step 3 Lift the cover and pull the flash card up and out of its slot (Figure 5-47).
Chapter 5 Maintaining the Cisco 10008 Router Upgrading SDRAM on the PRE Caution Always tighten the captive screw on the PCMCIA flash card cover to prevent the risk of a harmful ESD event and to ensure electromagnetic interference (EMI) shielding. Figure 5-49 Tightening the Captive Screw FANS OK FAN FAILURE MULTIFAN FAILURE When hot CAUTION removal swapping this fan be done and replaceme tray, system in under two nt must shutdown minu will occutes or r.
Chapter 5 Maintaining the Cisco 10008 Router Upgrading SDRAM on the PRE Table 5-1 Caution Available SDRAM Upgrades SDRAM Upgrade Options Cisco Part Number 256 MB SDRAM ESR-PRE-MEM-256M= 512 MB SDRAM ESR-PRE-MEM-512M= To prevent (electrostatic discharge) ESD damage, always wear an ESD-preventive wrist or ankle strap, and handle DIMMs by the edges only. Avoid touching the memory pins or traces (the metal fingers along the connector edge of the DIMM).
Chapter 5 Maintaining the Cisco 10008 Router Upgrading SDRAM on the PRE Place the PRE on an antistatic mat or pad so that the DIMMs are facing up (Figure 5-50). Figure 5-51 Removing the DIMM 1 1 Step 2 132838 1 Ejector tab Remove each DIMM from its slot by pushing its ejector tabs out to the side and lifting the DIMM straight up (Figure 5-51). Properly Handling a DIMM 132842 Figure 5-52 1 1 Step 3 Key Remove a new DIMM from its antistatic bag (Figure 5-52).
Chapter 5 Maintaining the Cisco 10008 Router Upgrading SDRAM on the PRE Caution To prevent (electrostatic discharge) ESD damage, always wear an ESD-preventive wrist or ankle strap, and handle DIMMs by the edges only. Avoid touching the memory pins or traces (the metal fingers along the connector edge of the DIMM).
Chapter 5 Maintaining the Cisco 10008 Router Upgrading SDRAM on the PRE If the system fails to boot properly after you perform these corrective actions, contact the Cisco Technical Assistance Center (TAC) for additional help. Before you contact TAC, make a note of any error messages, unusual LED states, or any other indications that might help the service representative to identify the problem.
A P P E N D I X A Technical Specifications Table A-1 lists the specifications for the Cisco 10008 router. Table A-1 Cisco 10008 Router System Specifications Description Physical specifications Temperature range Relative humidity Specifications • Weight: 130 lb (59.02 kg) fully configured chassis • Height: 21.75 in. (55.2 cm) • Width: 17.5 in. (44.4 cm) • Depth: 12.0 in. (30.4 cm) • Chassis depth with front cover: 13.75 in. (34.9 cm) • Mounting: 19 in. or 23 in.
Appendix A Table A-1 Technical Specifications Cisco 10008 Router System Specifications (continued) Description Specifications Power entry modules DC PEM Supports up to two separate −48 VDC input feeds by means of built-in two-position terminal blocks • Part Number: ESR-PWR-DC (Primary) Part Number: ESR-PWR-DC\R (Redundant) • DC input voltage: −48 to −60 VDC • DC input current: 20A @ −48 VDC • Power consumption: 1200W maximum • Heat dissipation: 3768 Btu 2/hr AC PEM • Part Number: ESR-PWR-A
Appendix A Technical Specifications Table A-1 Cisco 10008 Router System Specifications (continued) Description Performance routing engine (PRE) Specifications • Part Number: ESR-PRE1 (Primary) Part Number: ESR-PRE1/R (Redundant) • Power: 80W • Max per chassis: 2 • Weight: 7.5 lb (3.41 kg) Height: 16.0 in. (40.64 cm) Depth: 9.97 in. (25.32 cm) Width: 1.91 in. (4.84 cm) Three Interface ports: • RJ-45 IEEE 802.
Appendix A Technical Specifications Cisco 10008 Router Hardware Installation Guide A-4 OL-0659-13
A P P E N D I X B Repacking the Box If your system is damaged, you must repack it for return shipment. Use the original shipping containers. Figure B-1 shows an exploded view of the system and packing materials.
Appendix B Repacking the Box 6 1 FANS FAN OK MULTI- FAILURE FAN FAILURE CAUTION When hot swapping removal this fan be done and replaceme tray, system in under nt must shutdown two minutes will occur.
Appendix B Repacking the Box Figure B-2 Cisco 10008 System Package 1 132823 2 3 1 Carton 2 Pallet 3 Packing straps Step 5 Fold the outside carton down over the top of the accessory boxes and seal with packing tape (Figure B-2). Step 6 Wrap two packaging straps tightly around the top and bottom of the package to hold the outside carton and the bottom pallet (Figure B-2). Caution Do not use tape to hold the outside carton to the bottom pallet. Packaging straps must be used.
Appendix B Repacking the Box Cisco 10008 Router Hardware Installation Guide B-4 OL-0659-13
G L OS S A RY Symbols 1+1 APS See APS. 10BaseT 10-Mbps baseband Ethernet specification using two pairs of twisted-pair cabling (Category 3, 4, or 5): one pair for transmitting data and the other for receiving data. 10BaseT, which is part of the IEEE 802.3 specification, has a distance limit of approximately 328 feet (100 meters) per segment. See also IEEE 802.3 and Ethernet. 100BaseT 100-Mbps baseband Fast Ethernet specification using UTP wiring.
Glossary A AAL ATM adaptation layer. Service-dependent sublayer of the data link layer. The AAL accepts data from different applications and presents it to the ATM layer in the form of 48-byte ATM payload segments. AALs consist of two sublayers:the convergence sublayer and the segmentation and reassembly sublayer. Four types of AAL recommended by the ITU-T are AAL1, AAL2, AAL3/4, and AAL5; the Cisco 10008 router uses AAL5.
Glossary B Backplane The circuit board at the back of the chassis that all components plug into. It provides the physical connection between an interface processor or line card, and the data and power distribution buses inside a chassis. Bellcore Bell Communications Research. Former name of the organization that performs research and development on behalf of the Regional Bell Operating Companies (RBOCs). Bellcore is now called Telcordia. BER Bit error rate.
Glossary Command Line Interface See CLI. Console Data terminal equipment (DTE) through which commands are entered into a host. Critical alarm An alarm condition that might affect most or all subscribers that connect to the reporting node. To obtain more information about a problem, use the show facility-alarm status command. See also Major alarm and Minor alarm. D Data terminal equipment See DTE. DCE Data circuit-terminating equipment (ITU-T expansion).
Glossary Edge Services Router See ESR. Electromagnetic interference See EMI. Electrostatic discharge See ESD. EMI Electromagnetic interference. Interference by electromagnetic signals that can cause reduced data integrity and increased error rates on transmission channels. EMP Electromagnetic pulse. Caused by lightning and other high-energy phenomena. Capable of coupling enough energy into unshielded conductors to destroy electronic devices. ESD Electrostatic discharge.
Glossary G GBIC Gigabit Ethernet converter. An interface module used by gigabit Ethernet and Fibre Channel to convert the serial electrical signals to the transmission medium’s physical layer signalling, which is typically optical. GBIC modules can be hot swapped and contain ID and system information that a switch or router can use to determine the network device's capabilities. Different GBICs handle different types of fiber cable. See 1000BaseLX/LH, 1000BaseSX, and 1000BaseZX.
Glossary IR Intermediate reach. SONET/SDH specification for transmit power and receive sensitivity that achieves a 9.3-mile (15-km) reach. ISP Internet Service Provider. A company that provides Internet access to other companies and individuals. ITU-T International Telecommunication Union Telecommunication Standardization Sector. International body that develops worldwide standards for telecommunications technologies. The ITU-T carries out the functions of the former CCITT. L LAN Local-area network.
Glossary MAC Media Access Control. Lower of the two sublayers of the data link layer defined by the IEEE. The MAC sublayer handles access to shared media. MAC address Standardized data link layer address that is required for each port or device that connects to a LAN. Other devices in the network use these addresses to locate specific ports in the network, and to create and update routing tables and data structures. MAC addresses are 6 bytes long and are controlled by the IEEE.
Glossary Multiplexing An activity in which multiple logical signals are transmitted simultaneously across a single physical channel. Multiprotocol Label Switching See MPLS. N NEBS Network Equipment Building Systems. The Telcordia (formerly Bellcore) requirements for equipment deployed in a central office environment.
Glossary P Logical grouping of information that includes a header containing control information and (usually) user data. Packets are most often used to refer to network layer units of data. The terms datagram, frame, message, and segment are also used to describe logical information groupings at various layers of the OSI reference model and in various technology circles. Packet Packet Over SONET See POS.
Glossary Q QoS Quality of service. A measure of performance for a transmission system that reflects its transmission quality and service availability. QPPB QoS Policy Propagation by BGP. A feature that classifies packets by IP precedence based on BGP community lists, BGP autonomous system paths, and access lists.
Glossary Simple Network Management Protocol See SNMP. Single-mode fiber See SMF. SMF Single-mode fiber. Fiber-optic cabling with a narrow core that allows light to enter only at a single angle. Such cabling has higher bandwidth than multimode fiber, but requires a light source with a narrow spectral width (for example, a laser). Also called monomode fiber. See also Multimode fiber. SNMP Simple Network Management Protocol. Network management protocol used almost exclusively in TCP/IP networks.
Glossary TDM Time-division multiplexing. A technique in which information from multiple channels can be allocated bandwidth on a single wire based on preassigned time slots. Bandwidth is allocated to each channel regardless of whether the station has data to transmit. Telcordia Organization that performs research and development on behalf of the Regional Bell Operating Companies (RBOCs). Formerly called Bellcore. TELNET Standard terminal emulation protocol in the TCP/IP protocol stack.
Glossary U Unchannelized DS3 See Clear channel DS3. Unicast A message sent to a single network destination. Compare with Broadcast and Multicast. V Virtual Private Network See VPN. VLAN Virtual LAN. A group of devices on one or more LANs that are configured (using management software) so that they can communicate as if they were attached to the same wire, when in fact they are located on a number of different LAN segments.
Glossary Wide-area network See WAN. WRED Weighted Random Early Detection. RED uses an algorithm to randomly discard packets.The result of the drop is that the source detects the dropped traffic and slows its transmission. WRED combines the capabilities of the RED algorithm with IP precedence. This combination provides for preferential traffic handling for higher-priority packets.
Glossary Cisco 10008 Router Hardware Installation Guide GL-16 OL-0659-13
I N D EX description Numerics replacing 19-inch rack 3-3 1-6 5-10 troubleshooting BNC connectors 5-11 1-3 boot A command AC/DC power configuration file 1-3 bootflash, secondary AC PEM description boot loader 1-7 air filter, replacing airflow Break function chassis clearance common normally open 5-32 Minor 5-32 4-9 5-35 5-35 C 5-32 cable length, factors determining 5-32 Major 2-2 size, changing alarm indicators connecting 3-1 buffer 5-35 normally closed 1-11 4-9 BTUs
Index grounding lugs config register value command 3-14 line card slots configuration setup 1-1 module compartment 1-8 non-rack installation 3-11 preventing overheating rear view circuitry 20A DB-25 serial 3-2 DS3 2-3 powerup copy command 4-3 1-3 D CLI file system names 4-7 DB-25 serial connector 4-2 DB-9 serial connector 2-5 command prompt description 4-10 filename 4-8, 5-3 dir 4-8 4-8 4-5 privileged EXEC 5-49 replacing 5-47 display on PRE 5-49 1-11 4-8 4-10 ser
Index EMI predict and remedy shielding 2-6 5-4 replacing 5-6 front view of chassis 2-12 EMP, avoiding removing 1-4 FRU 2-6 removing and replacing ESD prevention guidelines wrist strap troubleshooting 2-12 FTP protocol 2-12 5-3 4-12 4-7 Ethernet 10BASE-T cable 3-32 G 3-33 cable requirements 3-32 connection to 10BASE-T hub grounding lug 3-32 Burndy # YA8CL2TC10 3-33 Panduit # LCD8-10-AL LAN connections 3-33 straight-through cable Ethernet port 3-14 3-14 Thomas & Betts # 54
Index radio frequency NVRAM 2-6 IOS command line interface file system See CLI 4-7 ignoring contents size IP address 4-9 4-8 4-14 router address 4-2 routing command subnet mask O 4-6 4-5 ISP, requirements operating conditions, chassis 1-1 optical network interfaces L 2-5 1-1 P Layer 3 router 1-1 Parallel eXpress Forwarding LEDs password fan failure 4-13 fault 4-12 LNK 4-13 miswire 4-12 4-12 4-4 Telnet 4-4 backing up card slots 4-12 flash cards line cards 5-3 1
Index Ethernet remote devices 4-13 PRE auxiliary PRE console RJ-45 RJ-45 connectors 1-9, A-3 router power S 4-11 1-2 safety PRE warning definition alphanumeric display auxiliary port 1-11 1-9 console port safety information 1-11 front panel scalability 1-9 1-9 replacing DIMMs product disposal 1-2 upgrading 1-10 5-36 specifications xi configurations PCMCIA card slots replacing 5-47 5-46 5-46 secondary bootflash 4-7 service compress-config global configuration command 4-8
Index work during lightening activity T warning, description T1 connections 1-2 practices rack x wiring telco environment 2-14 1-1 viii safety (warning) 2-4 3-1 Telnet connection session 4-4 temperature 2-2 4-13 warning messages 2-9 terminal server connections 4-2 TFTP protocol server tie wraps 4-7 4-11 5-18, 5-36 tools and supplies 3-18 tools for maintenance twisted-pair cabling 5-3 2-6 U undelete command 4-8 V voltage 2-2 W warning 1-11 chassis installation disconnect
