Cisco Media Gateway Controller Software Release 9 Billing Interface Guide December, 2007 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
CONTENTS Preface xi Document Objective Audience xi xi Document Organization xii Document Conventions xii Cisco Media Gateway Controller Documentation Suite xv Cisco Media Gateway Controller Documentation Map xvi Obtaining Documentation, Obtaining Support, and Security Guidelines Summary History of Document Changes CHAPTER 1 Billing Interfaces xvii xvii 1-1 Billing Capabilities Overview 1-1 System Interfaces 1-1 Physical Interface 1-1 RADIUS Interface 1-2 Message Interface 1-2 CDB Message
Contents Answered CDB Record (Tag: 1010/Release 5 or Later) 1-21 Deselected Outgoing Circuit CDB Record (Tag: 1020/Release 5 or Later) 1-25 Aborted Attempt CDB Record (Tag: 1030/Release 5 or Later) 1-27 Release CDB Record (Tag: 1040/Release 5 or Later) 1-31 Interrupted CDB Record (Tag: 1050/Release 5 or Later) 1-34 On-Going (Call) CDB Record (Tag: 1060/Release 5 or Later) 1-34 Maintenance CDB Record (Tag: 1070/Release 5 or Later) 1-37 SS7 CIC Audit CDB Record (Tag: 1071/Release 9 or Later) 1-37 External Ac
Contents Originating Line Information (Tag: 3002/ITU) Retired 1-70 Calling Number Nature of Address (Tag: 3003/ITU) 1-70 Charged Number Nature of Address (Tag: 3004/ITU) Retired 1-71 Dialed Number Nature of Address (Tag: 3005) 1-72 LRN Nature of Address (Tag: 3006/ITU) 1-73 Called Number Nature of Address (Tag: 3007/ITU) 1-74 Reason Code (Tag: 3008/ITU) 1-75 Forward Call Indicators Received (Tag: 3009/ITU) 1-88 Forward Call Indicators Sent (Tag: 3010/ITU) 1-89 Nature of Connection Indicators Received (Tag:
Contents Total Meter Pulses (Tag: 4030) 1-106 Maintenance Type (Tag: 4032) 1-106 Maintenance Reason (Tag: 4033)—Retired 1-107 Ingress Originating Point Code (Tag: 4034) 1-108 Ingress Destination Point Code (Tag: 4035) 1-108 Egress Originating Point Code (Tag: 4036) 1-109 Egress Destination Point Code (Tag: 4037) 1-109 Ingress Media Gateway ID (Tag: 4038) 1-110 Egress Media Gateway ID (Tag: 4039) 1-110 TCAP Transaction ID (Tag: 4040) 1-110 Transaction Start Time (Tag: 4041) 1-111 Transaction End Time (Tag:
Contents Original Called Number (Tag: 4080) 1-124 T.
Contents Service Activation (Tag: 4221) 1-145 PRI AOC Invoke Type (Tag: 4222) 1-145 PRI AOC – S Charge Information (Tag: 4223) 1-146 PRI AOC – D Charge Information (Tag: 4224) 1-146 PRI AOC – E Charge Information (Tag: 4225) 1-147 PRI AOC Invoke Failure (Tag: 4226) 1-147 Route Optimization/Path Replacement Action (Tag: 4227) 1-148 Route Optimization/Path Replacement Call Reference of Associated Call Instance (Tag: 4228) 1-148 Route Optimization/Path Replacement Trunk Group Info (Tag: 4229) 1-149 Route Opti
Contents Unique Call Correlator ID (Tag: 5000) 1-162 Miscellaneous Fields 1-163 MGC ID (Tag: 6000) 1-163 File Start Time (Tag: 6001) 1-163 File End Time (Tag: 6002) 1-163 Total Number of CDB Records (Tag: 6003) 1-164 MGC Version (Tag: 6004) 1-164 Interim CDB (Tag: 6005) 1-164 Protocol Specific CDEs 1-165 NTT 1-165 TTC Contract Number (Tag: 6100) 1-165 TTC Contract Number NOA (Tag: 6101) 1-165 TTC Charge Info (Tag: 6102) 1-165 TTC Charge Info Type (Tag: 6103) 1-166 TTC Charge Area Info (Tag: 6104) 1-166 CH
Contents Cisco Media Gateway Controller Software Release 9 Billing Interface Guide x OL-1089-11
Preface This preface includes the following sections: • Document Objective, page xi • Audience, page xi • Document Organization, page xii • Document Conventions, page xii • Cisco Media Gateway Controller Documentation Suite, page xv • Cisco Media Gateway Controller Documentation Map, page xvi • Obtaining Documentation, Obtaining Support, and Security Guidelines, page xvii • Summary History of Document Changes, page xvii Document Objective This guide provides reference information for the Cis
Preface Document Organization The major sections of this guide are summarized in Table 1. Table 1 Document Organization Chapter Title Description 1 Billing Interfaces Describes the Cisco MGC billing interface capabilities and its call detail records (CDRs). 2 Info Field Reference Provides additional information about the MGC Info Field (Tag 4031). Appendix A CDE Listings by Release Lists the call detail element (CDE) changes made for each release.
Preface Table 2 Conventions (continued) Convention Meaning Description/Comments Braces and vertical bars within square brackets ([ { | } ]) A required choice within an command [abc {def | ghi}] optional element You have three options: Nothing abc def abc ghi Caret character (^) Control key The key combinations ^D and Ctrl-D are equivalent: Both mean “hold down the Control key while you press the D key.” Keys are indicated in capital letters, but are not case sensitive.
Preface Table 3 Data Type Conventions Data Type Definition Example Integer A series of decimal digits from the set of 0 through 9 that 123 represents a positive integer. An integer can have one or 000123 4200000000 more leading zero digits (0) added to the left side to align the columns. Leading zeros are always valid as long as the number of digits is less than or equal to ten. Values of this type have a range of 0 through 4294967295.
Preface Cisco Media Gateway Controller Documentation Suite The documents that make up the Cisco MGC documentation set are listed in Table 4.
Preface Cisco Media Gateway Controller Documentation Map Refer to the map in Figure 1 to navigate through the media gateway controller documentation suite.
Preface Obtaining Documentation, Obtaining Support, and Security Guidelines For information on obtaining documentation, obtaining support, providing documentation feedback, security guidelines, and also recommended aliases and general Cisco documents, see the monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at: http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.
Preface Table 5 Summary History of Document Changes Subject Document Number and Change Date Tag revisions OL-1089-09, May 17, 2004 Change Summary • Modified the description of the 1060 CDB. • Retired tag 4045. • Modified information for tags 4044 and 4073. • Added tags 4083–4097, 4213–4226, and 6005. Tag revisions OL-1089-08, January 9, 2004 • Restored tags 4046 and 4047. Tag revisions OL-1089-08, December 3, 2003 • Modified the description of the 1060 CDB.
Preface Table 5 Summary History of Document Changes Subject Document Number and Change Date Tag revisions OL-1089-07, June 27, 2003 Change Summary • Modified CDB information for tag 4081.
Preface Table 5 Summary History of Document Changes Subject Document Number and Change Date Tag revisions OL-1089-06, August 16, 2002 Tag revisions OL-1089-06, July 10, 2002 Change Summary • Added data value information to the 3000 series tags from Q.763. • Identified tags 3002, 3004, 4046, and 4047 as retired. • Corrected the CBD information for tags 4052 and 4053. • Corrected descriptions for tags 4066–4068, 4070–4072, and 4074–4076.
Preface Table 5 Summary History of Document Changes Subject Document Number and Change Date Tag revisions OL-1089-03, November 27, 2001 ASCII output — OL-1089-02, November 16, 2001 OL-1089-01, October 18, 2001 Change Summary • Revised text for last bullet on page 1-7 and on page 1-8. • Removed “(retired in Release 9.0(1))” for Tag 2017 and Tag 3017. • Added Tag 4203. • Removed Tag 4064 and Tag 4065. • Removed references to ASCII output on page 1-2 to page 1-4.
Preface Cisco Media Gateway Controller Software Release 9 Billing Interface Guide xxii OL-1089-11
CH A P T E R 1 Billing Interfaces This chapter describes the Cisco Media Gateway Controller (MGC) billing interface capabilities and its call detail records (CDRs). This chapter is primarily a reference that contains the following sections: • Billing Capabilities Overview, page 1-1 • Cisco MGC Billing Interfaces, page 1-19 Billing Capabilities Overview The generic interface to the CDR dumper interface carries all the billing information in the form of call detail blocks (CDBs).
Chapter 1 Billing Interfaces Billing Capabilities Overview RADIUS Interface The RADIUS Enhancement for Accounting feature provides RADIUS interface support on the PGW 2200 for CDR data. For more information about the feature, including new CDRs, refer to the RADIUS Enhancement for Accounting feature guide. Message Interface The CDB message interface is a one-way interface to the CDR dumper. The following paragraphs describe the CDR message format for messages sent to the CDR dumper.
Chapter 1 Billing Interfaces Billing Capabilities Overview Figure 1-1 Length Tag Length Value 57859 Tag CDB TLV Record Format Sub-TLV messages The CDB message has both mandatory fields and optional fields. The following fields are mandatory in each CDB message. • Unique Call ID • Version • CDB Timestamp All other fields in the CDB message are considered optional. The optional fields do not appear in any sort of predefined order.
Chapter 1 Billing Interfaces Billing Capabilities Overview Figure 1-2 CDB Tag Categories 1000 MGC message IDs CDB message ID tag category 1900 Customer defined 1999 MGC ANSI format 2999 MGC ITU format 3999 MGC generic format CDB fields tag category 4999 Reserved 5900 Customer defined 5999 MGC miscellaneous 6999 Reserved Miscellaneous tag category 7999 57860 7900 Customer defined Formats and Codes The CDB message tag and the length fields are binary encoded using big-endian (BE).
Chapter 1 Billing Interfaces Billing Capabilities Overview Table 1-1 CDB Types Point in Call Event Description CDB Tag Value CDB Message/Record Answer call event Call went through and was answered. 1010 Set CDB record Deselected outgoing circuit event Circuit cannot be used, passed to another. 1020 Deselected outgoing circuit CDB record Aborted attempt call event Call did not get to setup status. 1030 Aborted attempt CDB record Release call event Released call.
Chapter 1 Billing Interfaces Call Data Block Descriptions Call Data Block Descriptions The CDB consists of several call data elements (CDEs) that are related to a certain point in call (PIC). Each CDE has a tag, a length, and a value. Table 1-2 defines the CDE fields in a CDB.
Chapter 1 Billing Interfaces Call Data Block Descriptions Table 1-2 CDB Call Data Element Fields for Current Release (continued) CDE Tag Numbers Millisecond Granularity CDB Name CDB Tag Common File Footer CDB 1100 4000–4002 End of Call 1110 4100–4109, 4000–4002, 4008–4012, 4014–4016, 4028, 4034–4037, 4046, 4047, 4060–4063, 4065, 4068, 4072, 4078–4080, 4082–4099, 4201–4212, 4213, 4214, 4227–4231, 4232, 4233, 4236, 4237, 4239, 4240–4245, 4246, 5000 Slave End of Call 1210 4002, 4003, 4006, 4008
Chapter 1 Billing Interfaces Call Data Block Descriptions To specify the CDR file timestamp unit, enter one of the following values: • S-Seconds (default). • M-Milliseconds; use this parameter if your configuration uses TCAP. Note If you use 1110 in the engine.CDRmessageTypes parameter (for TCAP), you must specify milliseconds for the CDRtimeStamp value. Note The timestamp value is in Coordinated Universal Time (UTC). Previously the term used was Greenwich Mean Time (GMT).
Chapter 1 Billing Interfaces Call Data Element Descriptions Table 1-4 Call Detail Record File Output Parameters Parameter Modification engine.CDRencodingFormat To specify the call detail record (CDR) file encoding format, enter one of the following values: engine.
Chapter 1 Billing Interfaces Call Data Element Descriptions The ITU formatted fields are used for customers requesting ITU-formatted-fields (as is the case for European customers) and is based on ITU-Q.763. The generic format provides common CDEs with one encoding scheme. The generic format is used to handle different protocol variants. Table 1-5 defines all the fields that can exist in any given CDB along with the associated tag and type for each one.
Chapter 1 Billing Interfaces Call Data Element Descriptions Table 1-5 CDE Detail Description for the Current Release (continued) Tag Value AnsDewered selected Aborted (1010) (1020) (1030) InterRelease rupted (1040) (1050) Ongoing (1060) Maintenance (1070) External DB (1080) End of 1071 Call 1210 (1110) 1260 Carrier Identification Parameter 2014 Y N Y N N N N N N N Carrier Selection Parameter 2015 Y N Y N N N N N Y N Jurisdiction Information Parameter 2016 Y N Y N N
Chapter 1 Billing Interfaces Call Data Element Descriptions Table 1-5 CDE Detail Description for the Current Release (continued) Tag Value AnsDewered selected Aborted (1010) (1020) (1030) InterRelease rupted (1040) (1050) Ongoing (1060) Maintenance (1070) External DB (1080) End of 1071 Call 1210 (1110) 1260 Nature of Connection Indicators Sent 3012 Y Y N N N N N N N N Transit Network Selection 3013 Y N Y N N N N N N N Redirecting Number NOA 3017 Y N Y N N N N N
Chapter 1 Billing Interfaces Call Data Element Descriptions Table 1-5 CDE Detail Description for the Current Release (continued) AnsDewered selected Aborted (1010) (1020) (1030) InterRelease rupted (1040) (1050) Ongoing (1060) Maintenance (1070) External DB (1080) End of 1071 Call 1210 (1110) 1260 Maint Trunk Group 4017 N N N N N N Y N N 1071 Maint Circuit Member 4018 N N N N N N Y N N N Glare Encountered 4019 N Y Y Y N N N N N N RLC Release Timepoint 4020 N Y
Chapter 1 Billing Interfaces Call Data Element Descriptions Table 1-5 CDE Detail Description for the Current Release (continued) Tag Value AnsDewered selected Aborted (1010) (1020) (1030) InterRelease rupted (1040) (1050) Ongoing (1060) Maintenance (1070) External DB (1080) End of 1071 Call 1210 (1110) 1260 Announcement Identification 4044 N N N Y N N N N N N Ingress Gateway Packet Info 4046 N N Y Y N N N N Y N Egress Gateway Packet Info 4047 N N Y Y N N N N Y
Chapter 1 Billing Interfaces Call Data Element Descriptions Table 1-5 CDE Detail Description for the Current Release (continued) AnsDewered selected Aborted (1010) (1020) (1030) InterRelease rupted (1040) (1050) Ongoing (1060) Maintenance (1070) External DB (1080) End of 1071 Call 1210 (1110) 1260 Maintenance Span 4075 ID N N N N N N Y N N N Maintenance BearChan ID 4076 N N N N N N Y N N N Maintenance Circuits Count 4077 N N N N N N Y N N N Charge Band Number 40
Chapter 1 Billing Interfaces Call Data Element Descriptions Table 1-5 CDE Detail Description for the Current Release (continued) Tag Value AnsDewered selected Aborted (1010) (1020) (1030) InterRelease rupted (1040) (1050) Ongoing (1060) Maintenance (1070) External DB (1080) End of 1071 Call 1210 (1110) 1260 ATM Negotiated Profiler 4094 Y N Y N N N N N Y N Route List Name 4095 Y N Y Y N N N N Y N Route Name 4096 Y N Y Y N N N N Y N MGCP Script Response String
Chapter 1 Billing Interfaces Call Data Element Descriptions Table 1-5 CDE Detail Description for the Current Release (continued) Tag Value AnsDewered selected Aborted (1010) (1020) (1030) InterRelease rupted (1040) (1050) Ongoing (1060) Maintenance (1070) External DB (1080) End of 1071 Call 1210 (1110) 1260 Short Call Indicator 4217 N N N Y N N N N Y N Charge Limit Exceeded 4218 N N N Y N N N N Y N Call Recovered Indication 4219 N N N Y N N N N Y N Partial Call
Chapter 1 Billing Interfaces Call Data Element Descriptions Table 1-5 CDE Detail Description for the Current Release (continued) AnsDewered selected Aborted (1010) (1020) (1030) InterRelease rupted (1040) (1050) Ongoing (1060) Maintenance (1070) External DB (1080) End of 1071 Call 1210 (1110) 1260 Rejecting Location 4233 Label Direction (added in 9.
Chapter 1 Billing Interfaces Cisco MGC Billing Interfaces Table 1-5 CDE Detail Description for the Current Release (continued) Tag Value AnsDewered selected Aborted (1010) (1020) (1030) InterRelease rupted (1040) (1050) Ongoing (1060) Maintenance (1070) External DB (1080) End of 1071 Call 1210 (1110) 1260 ANM Timepoint Sent_ms 4105 Y N N N N Y N N Y N First REL Timepoint_ms 4106 N Y Y Y N N N N Y N Second REL Timepoint_ms 4107 N N Y Y N N N N Y N RLC Timepoint
Chapter 1 Billing Interfaces Redundant Cisco MGC Configuration • File Transfer Protocol (FTP) interface • Generic interface FTP Interface The FTP interface allows the user to FTP the CDR files from the spool directory. This interface supports users who own a mediation system or data collocation system. Users can process the CDR files on a separate system. The Cisco MGC runs on Solaris UNIX that provides the standard file transfer capability (FTP).
Chapter 1 Billing Interfaces Cisco MGC Clock Synchronization If a call was stable during the failover, then the newly active Cisco MGC eventually generates an end of a call CDB (Release CDB or possibly an Interrupted CDB) for each call. The CDBs generated by the previous standby MGC include the same unique Call IDs. The mediation software requires correlating the CDB records from both systems. For both systems to be properly correlated, both Cisco MGC clocks must be synchronized with each other.
Chapter 1 Billing Interfaces Detailed CDB Description Table 1-6 Answered CDB Record (continued) Field Name Tag Value Dialed Number Nature of Address 2005 LRN Nature of Address 2006 Called Number Nature of Address 2007 Forward Call Indicators Received 2009 Forward Call Indicators Sent 2010 Nature of Connection Indicators Received 2011 Nature of Connection Indicators Sent 2012 Transit Network Selection 2013 Carrier Identification Parameter 2014 Carrier Selection Parameter 2015 Juris
Chapter 1 Billing Interfaces Detailed CDB Description Table 1-6 Answered CDB Record (continued) Tag Value Field Name Comments MGC Generic Tags CDB Versionb 4000 CDB Timepoint 4001 Call Reference ID 4002 IAM Timepoint 4003 When configured for seconds timepoint (Release 7 or later option) ACM Timepoint 4004 When configured for seconds timepoint (Release 7 or later option) ANM Timepoint 4005 When configured for seconds timepoint (Release 7 or later option) Originating Trunk Group 4008 O
Chapter 1 Billing Interfaces Detailed CDB Description Table 1-6 Answered CDB Record (continued) Field Name Tag Value Ingress SigPath ID 4066 Ingress Span ID 4067 Ingress BearChan ID 4068 Ingress ProtocolId 4069 Egress SigPath ID 4070 Egress Span ID 4071 Egress BearChan ID 4072 Egress ProtocolId 4073 Original Called Number 4080 Release 9.3(1) and later Charge Indicator 4083 Release 9.5(2) and later Outgoing Calling Party Number 4084 Release 9.
Chapter 1 Billing Interfaces Detailed CDB Description Table 1-6 Answered CDB Record (continued) Field Name Tag Value Comments H323 Destination 4236 Release 9.7 and later Ingress Redirecting Number 4237 Added in a Release 9.5(2) patch CNAM DIP 4240 Release 9.7 and later Calling Name 4241 Release 9.7 and later Terminating Remote SIP Host 4242 Release 9.7 and later Terminating Local SIP Host 4243 Release 9.7 and later SIP Transport 4246 Release 9.
Chapter 1 Billing Interfaces Detailed CDB Description Table 1-7 Deselected Outgoing Circuit CDB Record (continued) Field Name Tag Value Comments When configured for ITU encoding (Release 7 or later) ITU Based Formatted Fields Reason Code 3008 Forward Call Indicators Received 3009 Forward Call Indicators Sent 3010 Nature of Connection Indicators Received 3011 Nature of Connection Indicators Sent 3012 MGC Generic Tags CDB Version 4000 CDB Timepoint 4001 Call Reference ID 4002 IAM Timepoi
Chapter 1 Billing Interfaces Detailed CDB Description Table 1-7 Deselected Outgoing Circuit CDB Record (continued) Field Name Tag Value RLC Timepoint Sent_ms 4109 Comments Cisco Reserved Tags Unique Call ID (Release 9 and later) 5000 Aborted Attempt CDB Record (Tag: 1030/Release 5 or Later) Table 1-8 lists data about the aborted attempt. CDB Tag 1030 is generated for an attempted call that did not get to Setup status. That is a call that did not get answered.
Chapter 1 Billing Interfaces Detailed CDB Description Table 1-8 Aborted Attempt CDB Record (continued) Field Name Tag Value Comments When configured for ITU encoding (Release 7 or later) ITU Based Formatted Fields Calling Party Category 3000 User Service Information 3001 Originating Line Information 3002 Calling Number Nature of Address 3003 Dialed Number Nature of Address 3005 LRN Nature of Address 3006 Called Number Nature of Address 3007 Reason Code 3008 Forward Call Indicators Re
Chapter 1 Billing Interfaces Detailed CDB Description Table 1-8 Aborted Attempt CDB Record (continued) Field Name Tag Value Comments RLC Timepoint 4020 When timepoint in seconds is selected First Release Source 4028 LNP Dip 4029 MGC Info Field 4031 Ingress Originating Point Code 4034 Ingress Destination Point Code 4035 Egress Originating Point Code 4036 Egress Destination Point Code 4037 Ingress Media Gateway (CU) 4038 Egress Media Gateway (CU) 4039 Ingress Gateway Packet Info 4
Chapter 1 Billing Interfaces Detailed CDB Description Table 1-8 Aborted Attempt CDB Record (continued) Field Name Tag Value Comments Ingress MGCP DLCX Return Code 4087 Release 9.5(2) and later Egress MGCP DLCX Return Code 4088 Release 9.5(2) and later Network Translated Address Indicator 4089 Release 9.5(2) and later Reservation Request Accepted 4090 Release 9.5(2) and later Reservation Request Error Count 4091 Release 9.5(2) and later ATM Ingress Configured Profile 4092 Release 9.
Chapter 1 Billing Interfaces Detailed CDB Description Table 1-8 Aborted Attempt CDB Record (continued) Field Name Tag Value Comments H323 Destination 4236 Release 9.7 and later Ingress Redirecting Number 4237 Added in a Release 9.5(2) patch Service Usage Data 4239 Release 9.7 and later CNAM DIP 4240 Release 9.7 and later Calling Name 4241 Release 9.7 and later Terminating Remote SIP Host 4242 Release 9.7 and later Terminating Local SIP Host 4243 Release 9.
Chapter 1 Billing Interfaces Detailed CDB Description Table 1-9 Release CDB Record (continued) Field Name Tag Value When configured for ITU encoding (Release 7 or later) ITU Based Formatted Fields Reason Code Comments 3008 MGC Generic Tags CDB Version 4000 CDB Timepoint 4001 Call Reference ID 4002 REL Timepoint 4006 Glare Encountered 4019 RLC Timepoint 4020 First Release Source 4028 Total Meter Pulses 4030 Announcement Identification 4044 Ingress Gateway Packet Info 4046 Rest
Chapter 1 Billing Interfaces Detailed CDB Description Table 1-9 Release CDB Record (continued) Field Name Tag Value Comments Originating Leg DSP Statistics 4098 Release 9.4(1) and later Terminating Leg DSP Statistics 4099 Release 9.4(1) and later Ingress Media Device Address 4205 Release 9.4(1) and later Egress Media Device Address 4206 Release 9.4(1) and later Initial Codec 4207 Release 9.4(1) and later Final Codec 4208 Release 9.
Chapter 1 Billing Interfaces Detailed CDB Description Table 1-9 Release CDB Record (continued) Tag Value Field Name Comments Cisco Reserved Tags Unique Call ID (Release 9 and later) 5000 Interrupted CDB Record (Tag: 1050/Release 5 or Later) Table 1-10 lists data about the interrupted CDB. CDB Tag 1050 is created when a call is terminated without a Release message.
Chapter 1 Billing Interfaces Detailed CDB Description Table 1-11 lists data about the on-going (Call) CDB. Note In Release 7 and later, the long duration includes more fields than it does in Release 5. The extra fields are marked Release 7 and later. Table 1-11 On-going CDB Record Tag Value Field Name Comments ANSI-Specific Tags Egress Calling Number NOA 2018 Added in a Release 9.5(2) patch. Present only when 1110 is configured. Not recorded for point-in-call mode.
Chapter 1 Billing Interfaces Detailed CDB Description Table 1-11 On-going CDB Record (continued) Field Name Tag Value Comments Calling Number 4010 Optional. Present only when 1110 is configured. Dialed Number 4012 Optional. Present only when 1110 is configured. Called Number 4014 Optional. Present only when 1110 is configured. Terminating Trunk Group 4015 Optional. Present only when 1110 is configured. Terminating Member 4016 Optional. Present only when 1110 is configured.
Chapter 1 Billing Interfaces Detailed CDB Description Maintenance CDB Record (Tag: 1070/Release 5 or Later) Table 1-12 lists data about the maintenance record CDB type. CDB Tag 1070 is created for maintenance activity (such as block or unblock) on a circuit. Table 1-12 Maintenance CDB Record Tag Value Field Name MGC Generic Tags CDB Version 4000 CDB Timepoint 4001 Call Reference ID 4002 Maint Trunk Group 4017 Maint Circuit Member 4018 Maint Type 4032 Maint Reason (Retired in Release 9.
Chapter 1 Billing Interfaces Detailed CDB Description Table 1-13 SS7 CIC Audio CDB Record (continued) Field Name Tag Value Maint Trunk Group 4017 Appears when the MGC is configured for call control. Maintenance SigPath ID 4074 Appears when the MGC is configured for signaling. Total Circuit Count 4234 added in 9.4(1) patch Total Circuit Unavailable Count 4235 added in 9.4(1) patch Comments Cisco Reserved Tags Unique Call ID Note 5000 CDB 1071 is configurable in XECfgParm.
Chapter 1 Billing Interfaces Detailed CDB Description • Propagation block (gateway initiated blocking) CDB Tag 1071 generation rules: • If CDB Tag 1071 is generated as the result of the sta-aud-cic MML command, it includes the CIC unavailability information per trunk group for switched configuration, or per signaling service for nailed up. For other two scenarios, it only generates the information for the trunk groups that are impacted. • CDB Tag 1071 is generated only on the active side.
Chapter 1 Billing Interfaces Detailed CDB Description File Header CDB (Tag: 1090/Release 7 or Later) The CDR dumper generates the File Header CDB at the beginning of each new CDR file. It is generated according to the CDB creation guidelines, where the first three fields are mandatory and are located in their specified positions (refer to Table 1-17). Note This CDB is not configurable. Users cannot enable or disable the CDB nor can they select which fields are to be included.
Chapter 1 Billing Interfaces Detailed CDB Description Table 1-18 File Footer CDB Record (continued) Field Name Tag Value Call Reference ID 4002 Information Source This will always be 0, for compatibility with all other CDB layouts.
Chapter 1 Billing Interfaces Detailed CDB Description Table 1-19 End of Call CDB Record (continued) ANSI ITU Tag Value Description Tag Value Description 4001 CDB Timepoint 4001 CDB Timepoint 4002 Call Reference ID 4002 Call Reference ID 4008 Originating Trunk Group 4008 Originating Trunk Group 4009 Originating Member 4009 Originating Member 4010 Calling Number 4010 Calling Number 4011 Charged Number 4011 Charged Number 4012 Dialed Number 4012 Dialed Number 4014 Called
Chapter 1 Billing Interfaces Detailed CDB Description Table 1-19 End of Call CDB Record (continued) ANSI ITU Tag Value Description Tag Value Description 4080 Original Called Number 4080 Original Called Number 4082 Charge Unit Number 4082 Charge Unit Number 4083 Charge Indicator (Release 9.5(2) and up) 4083 Charge Indicator(Release 9.5(2) and up) 4084 Outgoing Calling Party Number (Release 9.5(2) and up) 4084 Outgoing Calling Party Number (Release 9.
Chapter 1 Billing Interfaces Detailed CDB Description Table 1-19 End of Call CDB Record (continued) ANSI ITU Tag Value Description Tag Value Description 4104 ANM Timepoint Received_msec 4104 ANM Timepoint Received_msec 4105 ANM Timepoint Sent_msec 4105 ANM Timepoint sent_msec 4106 First REL Timepoint_msec 4106 First REL Timepoint_msec 4107 Second REL Timepoint_msec 4107 Second REL Timepoint_msec 4108 RLC Timepoint Received_msec 4108 RLC Timepoint Received_msec 4109 RLC Timepo
Chapter 1 Billing Interfaces Detailed CDB Description Table 1-19 End of Call CDB Record (continued) ANSI Tag Value ITU Tag Value Description Description 4218 Charge Limit Exceeded (Release 9.5(2) 4218 and later) Charge Limit Exceeded (Release 9.5(2) and later) 4219 Call Recovered Indication (Release 9.5(2) and later) 4219 Call Recovered Indication (Release 9.5(2) and later) 4220 Partial Calling Line Identity (Release 9.5(2) and later) 4220 Partial Calling Line Identity (Release 9.
Chapter 1 Billing Interfaces Detailed CDB Description Table 1-19 End of Call CDB Record (continued) ANSI ITU Tag Value Description Tag Value Description 4240 CNAM DIP (Release 9.7 and later) 4240 CNAM DIP (Release 9.7 and later) 4241 Calling Name (Release 9.7 and later) 4241 Calling Name (Release 9.7 and later) 4242 Terminating Remote SIP Host (Release 4242 9.7 and later) Terminating Remote SIP Host (Release 9.7 and later) 4243 Terminating Local SIP Host (Release 9.
Chapter 1 Billing Interfaces Detailed CDB Description Table 1-20 Slave End-of-Call CDB Record (continued) Field Name Tag Value Originating Member 4009 Terminating Trunk Group 4015 Terminating Member 4016 RO/PR Executed 4227 Added in Release 9.6(1) RO/PR Other Call Ref 4228 Added in Release 9.6(1) Comments Cisco Reserved Tags Unique Call ID (Release 9 and later) 5000 Slave Long Duration Call CDB Record (Tag: 1260/Release 9.
Chapter 1 Billing Interfaces CDE Detail Description CDE Detail Description A call data element (CDE) is a field within the CDB that contains basic information about a billing record. Examples of CDEs are the calling number and the called number. The CDEs are described in the CDE description form template as shown in Table 1-22. CDE description forms for each of the CDBs listed near the bottom in Table 1-22 are included in Table 1-23 through Table 1-213.
Chapter 1 Billing Interfaces CDE Detail Description CDEs Encoded in ANSI Calling Party Category (Tag: 2000/ANSI) Table 1-23 Calling Party Category Description Form Name: Calling Party Category Tag: 2000 Source: MDL Description/Purpose: Indicates what type of calling party is placing the call. Format: ANSI T1.
Chapter 1 Billing Interfaces CDE Detail Description User Service Information (Tag: 2001/ANSI) Table 1-24 User Service Information Description Form Name: User Service Information Tag: 2001 Source: MDL Description/Purpose: This parameter is used to send the data transmission parameters to the distant exchange. The field format is the same as the format for the bearer capability information element from ANSI standard T1.607. Format: ANSI T1.
Chapter 1 Billing Interfaces CDE Detail Description Originating Line Information (Tag: 2002/ANSI) Table 1-25 Originating Line Information Description Form Name: Originating Line Information Tag: 2002 Source: MDL Description/Purpose: This information is captured from the originating line information parameter. Format: ANSI T1.113 Length in Octets: 1 Data Value: 00000000 to 01100011 Binary equivalent of the digits 01100100 to 11111111 Reserved Extended Data Value: No extended value.
Chapter 1 Billing Interfaces CDE Detail Description Calling Number Nature of Address (Tag: 2003/ANSI) Table 1-26 Calling Number Nature of Address Description Form Name: Calling Number Nature of Address Tag: 2003 Source: MDL Description/Purpose: Indicates to the Cisco MGC how the number was delivered. It indicates the calling party type of address. In POTS calling, two values are usually used: unique national number and nonunique national number. Format: ANSI T1.
Chapter 1 Billing Interfaces CDE Detail Description Charged Number Nature of Address (Tag: 2004/ANSI) Table 1-27 Charged Number Nature of Address Description Form Name: Charged Number Nature of Address Tag: 2004 Source: MDL Description/Purpose: Indicates to the Cisco MGC how the number was delivered. Format: ANSI T1.
Chapter 1 Billing Interfaces CDE Detail Description Dialed Number Nature of Address (Tag: 2005/ANSI) Table 1-28 Dialed Number Nature of Address Description Form Name: Dialed Number Nature of Address Tag: 2005 Source: MDL Description/Purpose: Allows the Call Process to route a call differently based on the Nature of Address (NOA) value provided in the IAM called number parameter. This tag represents the external (for example, line) value of NOA for the called part number. Format: ANSI T1.
Chapter 1 Billing Interfaces CDE Detail Description LRN Nature of Address (Tag: 2006/ANSI) Table 1-29 LRN Nature of Address Description Form Name: LRN Nature of Address Tag: 2006 Source: MDL Description/Purpose: Stores the NOA of LRN from an INAP query. Format: ANSI T1.
Chapter 1 Billing Interfaces CDE Detail Description Called Number Nature of Address (Tag: 2007/ANSI) Table 1-30 Called Number Nature of Address Description Form Name: Called Number Nature of Address Tag: 2007 Source: MDL Description/Purpose: The tag contains the Nature of Address (NOA) value from the egress protocol message used in the outbound IAM. The NOA value in this tag is from the ingress protocol message.
Chapter 1 Billing Interfaces CDE Detail Description Reason Code (Tag: 2008/ANSI) Table 1-31 Reason Code Description Form Name: Reason Code Tag: 2008 Source: MDL Description/Purpose: Incorporates SS7 release with cause values and any additional reasons that the basic call model determines. Format: ANSI T1.113 Length in Octets: 2 Data Value: The value of this field includes the first two octets of the cause indicators. Please refer to the ANSI T1.113 specification.
Chapter 1 Billing Interfaces CDE Detail Description Forward Call Indicators Received (Tag: 2009/ANSI) Table 1-32 Forward Call Indicators Received Description Form Name: Forward Call Indicators Received Tag: 2009 Source: MDL Description/Purpose: This is for the received Forward Call Indicator parameter in ISUP message. It includes the following fields: International Call Ind.; End To End Method Ind.; Interworking Ind.; IAM Segmentation Ind.; ISDN User Part Ind.; ISDN User Part Preference Ind.
Chapter 1 Billing Interfaces CDE Detail Description Forward Call Indicators Sent (Tag: 2010/ANSI) Table 1-33 Forward Call Indicators Sent Description Form Name: Forward Call Indicators Sent Tag: 2010 Source: MDL Description/Purpose: This is for the sent Forward Call Indicator parameter in ISUP message. It includes the following fields: International Call Ind.; End To End Method Ind.; Interworking Ind.; IAM Segmentation Ind.; ISDN User Part Ind.; ISDN User Part Preference Ind.; ISDN Access Ind.
Chapter 1 Billing Interfaces CDE Detail Description Nature of Connection Indicators Received (Tag: 2011/ANSI) Table 1-34 Nature of Connection Indicators Received Description Form Name: Nature of Connection Indicators Received Tag: 2011 Source: MDL Description/Purpose: Used to record the Nature of Connection received from the IAM. Three possible indicators can be received: the satellite indicator, the continuity check indicator, and the echo suppressor indicator. Format: ANSI T1.
Chapter 1 Billing Interfaces CDE Detail Description Nature of Connection Indicators Sent (Tag: 2012/ANSI) Table 1-35 Nature of Connection Indicators Sent Description Form Name: Nature of Connection Indicators Sent Tag: 2012 Source: MDL Description/Purpose: Used to record the Nature of Connection sent. Three possible indicators can be sent: the satellite indicator, the continuity check indicator, and the echo suppressor indicator. Format: ANSI T1.
Chapter 1 Billing Interfaces CDE Detail Description Transit Network Selection (Tag: 2013/ANSI) Table 1-36 Transit Network Selection Description Form Name: Transit Network Selection Tag: 2013 Source: MDL Description/Purpose: Includes Type of Network, Network Identification Plan, Digits, and Circuit Code. Format: ANSI T1.113 Length in Octets: 4 Data Value: Network Identification Plan—The Network ID plan field indicates to the Cisco MGC what type of ID the parameter has.
Chapter 1 Billing Interfaces CDE Detail Description Carrier Identification Parameter (Tag: 2014/ANSI) Table 1-37 Carrier Identification Parameter Description Form Name: Carrier Identification Parameter Tag: 2014 Source: MDL Description/Purpose: This is for the Carrier Identification Parameter in ISUP message. It includes the following fields: Network Identification Plan; Type of Network Identification; Spare; Digit 1; Digit 2; Digit 3; Digit 4 or Null. Format: ANSI T1.
Chapter 1 Billing Interfaces CDE Detail Description Jurisdiction Information Parameter (Tag: 2016/ANSI) Table 1-39 Jurisdiction Information Parameter Description Form Name: Jurisdiction Information Parameter Tag: 2016 Source: MDL Description/Purpose: This parameter provides numerical data indicating the geographic origination of the call. Format: IA5 Length in Octets: 6 Data Value: Digits from Jurisdiction Information Parameter. Extended Data Value: General Information: MGC Release: Release 5.
Chapter 1 Billing Interfaces CDE Detail Description Egress Calling Number Nature of Address (Tag 2018/ANSI) Table 1-41 Egress Calling Number Nature of Address Description Form Name: Egress Calling Number NOA Tag: 2018 Source: MDL Description/Purpose: This CDE records the calling party NOA sent in the outgoing message by the MGC. This field indicates the address type of the calling party. In POTS calling, there are usually two values that are used.
Chapter 1 Billing Interfaces CDE Detail Description Egress Redirecting Number Nature of Address (Tag 2019/ANSI) Table 1-42 Egress Redirecting Number Nature of Address Description Form Name: Egress Redirecting Number NOA Tag: 2019 Source: MDL Description/Purpose: This CDE records the redirecting calling number NOA sent in the outgoing message by the MGC. Format: ANSI T1.
Chapter 1 Billing Interfaces CDE Detail Description Egress Original Called Number Nature of Address (Tag 2020/ANSI) Table 1-43 Egress Calling Number Nature of Address Description Form Name: Egress Original Called Number NOA Tag: 2020 Source: MDL Description/Purpose: This CDE records the original called party NOA sent in the outgoing message by the MGC. Format: ANSI T1.
Chapter 1 Billing Interfaces CDE Detail Description CDE Encoded as ITU Recommendation Calling Party Category (Tag: 3000/ITU) Table 1-44 Calling Party Category Description Form Name: Calling Party Category Tag: 3000 Source: MDL Description/Purpose: Indicates what type of calling party is placing the call. Format: ITU-T Q.763 Length in Octets: 1 Data Value: 00000000 Calling party’s category is unknown (national use).
Chapter 1 Billing Interfaces CDE Detail Description User Service Information (Tag: 3001/ITU) Table 1-45 User Service Information Description Form Name: User Service Information Tag: 3001 Source: MDL Description/Purpose: Captures the User Service Information parameter of ITU-T ISUP. Format: ITU-T Q.763 Length in Octets: 2 to 13 Data Value: 8 7 6 5 4 3 2 1 Ext. Coding Standard Information Transfer Capability 2 Ext. Transfer Mode Information Transfer Rate 2a 1 Rate multiplier 3 Ext.
Chapter 1 Billing Interfaces CDE Detail Description Originating Line Information (Tag: 3002/ITU) Retired Table 1-46 Originating Line Information Description Form Name: Originating Line Information Tag: 3002 Source: MDL Description/Purpose: Indicates to the Cisco MGC what II digits are being sent from the LEC. This differentiates calls based on the II digits. Format: ITU-T Q.763 Length in Octets: 1 Data Value: Extended Data Value: No extended value.
Chapter 1 Billing Interfaces CDE Detail Description Charged Number Nature of Address (Tag: 3004/ITU) Retired Table 1-48 Charged Number Nature of Address Description Form Name: Charged Number Nature of Address Tag: 3004 Source: MDL Description/Purpose: Indicates the address type of the calling party. In POTS calling, the value is typically Unique National Number or Non-Unique National Number Format: ITU-T Q.
Chapter 1 Billing Interfaces CDE Detail Description Dialed Number Nature of Address (Tag: 3005) Table 1-49 Dialed Number Nature of Address Description Form Name: Dialed Number Nature of Address Tag: 3005 Source: MDL Description/Purpose: This value allows the Call Process to route a call differently based on the Nature of Address value provided in the IAM Called Number parameter. Format: ANSI T1.
Chapter 1 Billing Interfaces CDE Detail Description LRN Nature of Address (Tag: 3006/ITU) Table 1-50 LRN Nature of Address Description Form Name: LRN Nature of Address Tag: 3006 Source: MDL Description/Purpose: Stores the NOA of LRN from an INAP query. Format: ITU-T Q.
Chapter 1 Billing Interfaces CDE Detail Description Called Number Nature of Address (Tag: 3007/ITU) Table 1-51 Called Number Nature of Address Description Form Name: Called Number Nature of Address Tag: 3007 Source: MDL Description/Purpose: The tag contains the Nature of Address (NOA) value from the egress protocol message used in the outbound IAM.The NOA value in this tag is from the ingress protocol message.
Chapter 1 Billing Interfaces CDE Detail Description Reason Code (Tag: 3008/ITU) Table 1-52 Reason Code Description Form Name: Reason Code Tag: 3008 Source: MDL Description/Purpose: Incorporates C7 release with cause values and any additional reasons that the basic call model determines. Format: based on ITU-T Q.850 Length in Octets: 2 Data Value: Format: 8 1 Ext. 2 Ext.
Chapter 1 Billing Interfaces CDE Detail Description Table 1-52 Reason Code Description Form (continued) Cause value: (only applicable in the context of Recommendations Q.763 and Q.931) The cause value is divided into two fields, a class (bits 5 through 7) and a value within the class (bits 1 through 4). The class indicates the general nature of the event.
Chapter 1 Billing Interfaces CDE Detail Description Table 1-53 Cause Information Element/Parameter Definitions (continued) Cause Class/Value/No. Definition 000/0010/2 Application (Note 1) Reference (Note 2) Location (Note 3) Q.931 LN, TN DSS 1, ISUP Q.931 No route to destination—indicates that the called party cannot be reached because the network through which the call has been routed does not serve the destination desired.
Chapter 1 Billing Interfaces CDE Detail Description Table 1-53 Cause Information Element/Parameter Definitions (continued) Cause Class/Value/No. Definition Application (Note 1) Reference (Note 2) Location (Note 3) Q.769.1 LN 000/1110/14 QoR:ported number—indicates that an ISUP exchange detected that the called number was ported out (see Annex C/Q.769.1) 001/0000/16 Normal call clearing—indicates that the call DSS 1, ISUP Q.931, 2.3/Q.
Chapter 1 Billing Interfaces CDE Detail Description Table 1-53 Cause Information Element/Parameter Definitions (continued) Cause Class/Value/No. Definition Application (Note 1) Reference (Note 2) Location (Note 3) 001/0110/22 Number changed—returned to a calling party DSS 1, ISUP Q.931 when the called party number indicated by the calling party is no longer assigned. The new called party number may optionally be included in the diagnostic field.
Chapter 1 Billing Interfaces CDE Detail Description Table 1-53 Cause Information Element/Parameter Definitions (continued) Cause Class/Value/No. Definition Application (Note 1) 001/1100/28 DSS 1, ISUP Q.931 Invalid number format (address incomplete)—indicates that the called party cannot be reached because the called party number is not in a valid format or is not complete. Note 001/1101/29 001/1110/30 Location (Note 3) 2.1.1, 2.1.2, 2.9.8.3, 2.2.5 Annex A/ Q.763 DSS 1, ISUP Q.
Chapter 1 Billing Interfaces CDE Detail Description Table 1-53 Cause Information Element/Parameter Definitions (continued) Cause Class/Value/No. Definition 001/1111/31 Application (Note 1) Reference (Note 2) Location (Note 3) Remarks Normal, unspecified—used to report a normal DSS 1, ISUP Q.931 RLN event only when no other cause in the normal In Q.764, the TN, INTL, Call failure class applies. RLN information following indicating the sections: failure of a call 2.1.1, 2.1.2, due to the lapse 2.8.
Chapter 1 Billing Interfaces CDE Detail Description Table 1-53 Cause Information Element/Parameter Definitions (continued) Cause Class/Value/No. Definition Application (Note 1) Reference (Note 2) Location (Note 3) 010/1000/40 DSS 1 Permanent frame mode connection operational—included in a STATUS message to indicate that a permanently established frame mode connection is operational and capable of carrying user information (see Annex A/Q.933). 010/1001/41 DSS 1, ISUP Q.
Chapter 1 Billing Interfaces CDE Detail Description Table 1-53 Cause Information Element/Parameter Definitions (continued) Cause Class/Value/No. Definition Application (Note 1) 011/0010/50 Requested facility not subscribed—indicates that the user has requested a supplementary service which is implemented by the equipment which generated this cause, but which the user is not authorized to use. DSS 1, ISUP Q.931, Q.
Chapter 1 Billing Interfaces CDE Detail Description Table 1-53 Cause Information Element/Parameter Definitions (continued) Cause Class/Value/No. Definition Application (Note 1) Reference (Note 2) 100/0110/70 Only restricted digital information bearer capability is available (national use)— indicates that the calling party has requested an unrestricted bearer service but that the equipment sending this cause only supports the restricted version of the requested bearer capability.
Chapter 1 Billing Interfaces CDE Detail Description Table 1-53 Cause Information Element/Parameter Definitions (continued) Cause Class/Value/No. Definition Application (Note 1) Reference (Note 2) Location (Note 3) Q.
Chapter 1 Billing Interfaces CDE Detail Description Table 1-53 Cause Information Element/Parameter Definitions (continued) Cause Class/Value/No.
Chapter 1 Billing Interfaces CDE Detail Description Table 1-53 Cause Information Element/Parameter Definitions (continued) Cause Class/Value/No. Definition 110/0110/102 Application (Note 1) Reference (Note 2) DSS 1, ISUP Q.931 Recovery on timer expiry—indicates that a procedure has been initiated by the expiry of a Q.733.4 timer in association with error handling procedures. 2.4.3/Q.
Chapter 1 Billing Interfaces CDE Detail Description Forward Call Indicators Received (Tag: 3009/ITU) Table 1-54 Forward Call Indicators Received Description Form Name: Forward Call Indicators Received Tag: 3009 Source: MDL Description/Purpose: It is for the received Forward Call Indicator in ISUP message. It includes the following fields: International Call Ind.; End To End Method Ind.; Interworking Ind.; IAM Segmentation Ind.; ISDN User Part Ind.; ISDN User Part Preference Ind.; ISDN Access Ind.
Chapter 1 Billing Interfaces CDE Detail Description Table 1-54 Forward Call Indicators Received Description Form (continued) bitsKJSCCP method indicator 00no indication 01Connectionless method available 10Connection oriented method available 11Connectionless and Connection oriented methods available bit L:Spare bits P-M:Reserved for national use Note: The above values are for standard ITU SS7. Variants of ITU SS7 may have different values.
Chapter 1 Billing Interfaces CDE Detail Description Table 1-55 Forward Call Indicators Sent Description Form (continued) This bit can be set to any value in the country of origin. In the international network this bit is not checked. In the destination country, calls from the international network will have this bit set to 1.
Chapter 1 Billing Interfaces CDE Detail Description Nature of Connection Indicators Received (Tag: 3011/ITU) Table 1-56 Nature of Connection Indicators Received Description Form Name: Nature of Connection Indicators Received Tag: 3011 Source: MDL Description/Purpose: Used to record the Nature of Connection received from the IAM. There are three possible indicators that can be received: the satellite indicator, the continuity check indicator, and the echo suppressor indicator. Format: ITU-T Q.
Chapter 1 Billing Interfaces CDE Detail Description Nature of Connection Indicators Sent (Tag: 3012/ITU) Table 1-57 Nature of Connection Indicators Sent Description Form Name: Nature of Connection Indicators Sent Tag: 3012 Source: MDL Description/Purpose: Used to record the Nature of Connection sent from the IAM. There are three possible indicators that can be received: the satellite indicator, the continuity check indicator, and the echo suppressor indicator. Format: ITU-T Q.
Chapter 1 Billing Interfaces CDE Detail Description Transit Network Selection (Tag: 3013/ITU) Table 1-58 Transit Network Selection Description Form Name: Transit Network Selection Tag: 3013 Source: MDL Description/Purpose: Used to identify each previous network type transited. Format: ITU-T Q.763 Length in Octets: 1-n Data Value: 8 1 Odd/Even 7 6 5 4 Type of network identification 3 2 1 Network identification plan 2 . . Network identification .
Chapter 1 Billing Interfaces CDE Detail Description Redirecting Number Nature of Address (Tag 3017/ITU) Table 1-59 Redirecting Number Nature of Address Description Form Name: Called Number Nature of Address Tag: 3017 Source: MDL Description/Purpose: Indicates to the Cisco MGC how the number was delivered. It indicates the calling party address type. In POTS calling, there are usually two values that are used: Unique national number and Nonunique national number. Format: ITU-T Q.
Chapter 1 Billing Interfaces CDE Detail Description Egress Calling Number Nature of Address (Tag 3018/ITU) Table 1-60 Egress Calling Number Nature of Address Description Form Name: Egress Calling Number NOA Tag: 3018 Source: MDL Description/Purpose: This CDE records the calling party NOA sent in the outgoing message by the MGC. This field indicates the address type of the calling party. In POTS calling, there are usually two values that are used.
Chapter 1 Billing Interfaces CDE Detail Description Egress Redirecting Number Nature of Address (Tag 3019/ITU) Table 1-61 Egress Redirecting Number Nature of Address Description Form Name: Egress Redirecting Number NOA Tag: 3019 Source: MDL Description/Purpose: This CDE records the redirecting calling number NOA sent in the outgoing message by the MGC. Format: ITU-T Q.
Chapter 1 Billing Interfaces CDE Detail Description Egress Original Called Number Nature of Address (Tag 3020/ITU) Table 1-62 Egress Calling Number Nature of Address Description Form Name: Egress Original Called Number NOA Tag: 3020 Source: MDL Description/Purpose: This CDE records the original called party NOA sent in the outgoing message by the MGC. Format: ITU-T Q.
Chapter 1 Billing Interfaces CDE Detail Description MGC Generic CDEs CDB Version (Tag: 4000) Table 1-63 CDB Version Description Form Name: CDB Version Tag: 4000 Source: MDL Description/Purpose: Holds CDB version number to control raw CDB layout version. Format: BE Length in Octets: 1 Data Value: 1 Extended Data Value: No extended value. General Information: This field is required in every CDB. MGC Release: Release 5.0 and later.
Chapter 1 Billing Interfaces CDE Detail Description IAM/Setup Timepoint (Tag: 4003) Table 1-66 IAM/Setup Timepoint Description Form Name: IAM/Setup Timepoint Tag: 4003 Source: MDL/Engine Description/Purpose: Timepoint for receipt of IAM/Setup (or receipt of CRM if a CRM preceded the IAM). Format: BE Length in Octets: 4 Data Value: UNIX time format (number of seconds since January 1, 1970). Extended Data Value: No extended value.
Chapter 1 Billing Interfaces CDE Detail Description REL/Release Timepoint (Tag: 4006) Table 1-69 REL/Release Timepoint Description Form Name: REL/Release Timepoint Tag: 4006 Source: MDL/Engine Description/Purpose: Timepoint for receipt of first REL/Release. Format: BE Length in Octets: 4 Data Value: UNIX time format (number of seconds since January 1, 1970). Extended Data Value: No extended value.
Chapter 1 Billing Interfaces CDE Detail Description Originating Member (Tag: 4009) Table 1-72 Originating Member Description Form Name: Originating Member Tag: 4009 Source: MDL Description/Purpose: Contains the originating trunk member number within the originating trunk group. There can be 214 originating members when the MGC is configured for ANSI, and 212 originating members when configured for ITU.
Chapter 1 Billing Interfaces CDE Detail Description Dialed Number (Tag: 4012) Table 1-75 Dialed Number Description Form Name: Dialed Number Tag: 4012 Source: MDL Description/Purpose: These are the digits that were dialed by the calling party. Format: IA5 Length in Octets: 1 to 96 Data Value: The digits that were dialed by the calling party. Extended Data Value: No extended value. General Information: MGC Release: Release 5.0 and later.
Chapter 1 Billing Interfaces CDE Detail Description Terminating Trunk Group (Tag: 4015) Table 1-78 Terminating Trunk Group Description Form Name: Terminating Trunk Group Tag: 4015 Source: MDL/Engine Description/Purpose: Terminating Trunk Group number. Format: BE Length in Octets: 2 Data Value: The terminating trunk group number ranges from 1 to 16,384 when the MGC is configured for ANSI and the number ranges from 1 to 4096 when it is configured for ITU. Extended Data Value: No extended value.
Chapter 1 Billing Interfaces CDE Detail Description Maintenance Circuit Member (Tag: 4018) Table 1-81 Maintenance Circuit Member Name: Maintenance Circuit Member Tag: 4018 Source: MDL/Engine Description/Purpose: Maintenance circuit member number within a trunk group. There can be up to 214 members in a trunk group when the MGC is configured for ANSI and up to 212 members when configured for ITU.
Chapter 1 Billing Interfaces CDE Detail Description First Release Source (Tag: 4028) Table 1-84 First Release Source Description Form Name: First Release Source Tag: 4028 Source: MDL Description/Purpose: Indicates if the release source was an originating, terminating, or local (Cisco MGC) system. Format: BE Length in Octets: 1 Data Value: 0 = Originating side 1 = Terminating side 2 = Local (MGC) Extended Data Value: No extended value. General Information: MGC Release: Release 5.0 and later.
Chapter 1 Billing Interfaces CDE Detail Description Total Meter Pulses (Tag: 4030) Table 1-86 Total Meter Pulses Description Form Name: Total Meter Pulses Tag: 4030 Source: MDL Description/Purpose: Holds the total meter pulses. Certain Integrated Services Digital Network User Parts (ISUPs) and Telephone User Parts (TUPs) support this optional information. Format: BE Length in Octets: 2 Data Value: Total meter pulse counts sent out by Cisco MGC for a call. Extended Data Value: No extended value.
Chapter 1 Billing Interfaces CDE Detail Description Maintenance Reason (Tag: 4033)—Retired Table 1-88 Maintenance Reason Description Form Name: Maintenance Reason Tag: 4033 Source: MDL Description/Purpose: Indicates the reason that the maintenance was requested. Format: BE Length in Octets: 1 Data Value: Up to Release 9.2(2): 1 = Remote 2 = Local Release 9.
Chapter 1 Billing Interfaces CDE Detail Description Ingress Originating Point Code (Tag: 4034) Table 1-89 Ingress Originating Point Code Description Form Name: Ingress Originating Point Code Tag: 4034 Source: MDL Description/Purpose: Holds the ingress originating point code. Format: BE Length in Octets: 4 Data Value: The point code is in 4-byte integer format. Extended Data Value: No extended value.
Chapter 1 Billing Interfaces CDE Detail Description Egress Originating Point Code (Tag: 4036) Table 1-91 Egress Originating Point Code Name: Egress Originating Point Code Tag: 4036 Source: MDL Description/Purpose: Holds the egress originating point code. Format: BE Length in Octets: 4 Data Value: The point code is in 4-byte integer format. Extended Data Value: No extended value.
Chapter 1 Billing Interfaces CDE Detail Description Ingress Media Gateway ID (Tag: 4038) Table 1-93 Ingress Media Gateway ID Description Form Name: Ingress Media Gateway ID Tag: 4038 Source: MDL Description/Purpose: Ingress media gateway ID (expressed in address). Format: BE Length in Octets: 2 Data Value: 16 bits of binary value. Extended Data Value: No extended value. General Information: MGC Release: Release 7.0 and later.
Chapter 1 Billing Interfaces CDE Detail Description Transaction Start Time (Tag: 4041) Table 1-96 Transaction Start Time Description Form Name: Transaction Start Time Tag: 4041 Source: MDL/Engine Description/Purpose: The time at which the Cisco MGC sent an external request to an SCP, intelligent peripheral (IP), or some other database. Format: DT2 Length in Octets: 6 Data Value: UNIX time format (number of seconds since January 1, 1970). Extended Data Value: No extended value.
Chapter 1 Billing Interfaces CDE Detail Description Announcement ID (Tag: 4044) Table 1-99 Announcement ID Description Form Name: Announcement ID Tag: 4044 Source: MDL Description/Purpose: Announcement ID value. Format: BE Length in Octets: 2 Data Value: An integer value to identify which announcement to play. Extended Data Value: No extended value. General Information: MGC Release: Release 7.0 and later.
Chapter 1 Billing Interfaces CDE Detail Description Ingress Packet Info (Tag: 4046) Restored Table 1-101 Ingress Packet Info Description Form Name: Ingress Packet Info Tag: 4046 Source: MDL Description/Purpose: Contains the packets sent, packets received, packets lost, octets sent, octets received, jitter, and latency information (reserved 1 and 2) from the ingress gateway. On Release 9.7(3), H.248 support is added. For an H.
Chapter 1 Billing Interfaces CDE Detail Description Egress Packet Info (Tag: 4047) Restored Table 1-102 Egress Packet Info Description Form Name: Egress Packet Info Tag: 4047 Source: MDL Description/Purpose: Contains the packets sent, packets received, packets lost, octets sent, octets received, jitter, and latency information (reserved 1 and 2) from the egress gateway. On Release 9.7(3), H.248 support is added. For an H.
Chapter 1 Billing Interfaces CDE Detail Description Service Logic ID (Tag: 4049) Table 1-104 Service Logic ID Description Form Name: Service Logic ID Tag: 4049 Source: MDL Description/Purpose: This field value is used in an advanced intelligent network (AIN) environment. It records an identification of service logic in the SCP that was used. The AMAslpID returns from the SCP hold the service logic ID value.
Chapter 1 Billing Interfaces CDE Detail Description OOriginating Gateway Primary Select (Tag: 4052) Defined for Future Use Table 1-106 Originating Gateway Primary Select Form Name: Originating Gateway Primary Select Tag: 4052 Source: MDL/Engine Description/Purpose: Format: Binary Length in Octets: 1 Data Value: 0 = False 1 = True Extended Data Value: No extended value.
Chapter 1 Billing Interfaces CDE Detail Description Scale Factor (Tag: 4062) Table 1-109 Scale Factor Description Form Name: Scale Factor Tag: 4062 Source: MDL/Engine Description/Purpose: Used for reporting Advice of Charge information. Format: BE Length in Octets: 4 Data Value: The actual value for the scale factor is given by 10^x, where x is the value of the scale factor.
Chapter 1 Billing Interfaces CDE Detail Description Redirection Number (Tag: 4065) Table 1-111 Ingress SigPath ID Description Form Name: Redirection Number Tag: 4065 Source: MDL Description/Purpose: This tag contains the digits of the new number when the PGW redirects a call. Format: IA5 Length in Octets: 1-96 Data Value: Redirection number digits Extended Data Value: No extended value. General Information: MGC Release: Release 9.7 and later.
Chapter 1 Billing Interfaces CDE Detail Description Ingress BearChan ID (Tag: 4068) Table 1-114 Ingress BearChan ID Description Form Name: Ingress BearChan ID Tag: 4068 Source: MDL/Engine Description/Purpose: The ingress BearChan ID is used for incoming bearer channels. Format: BE Length in Octets: 4 Data Value: 32 bits of binary value Extended Data Value: No extended value. General Information: MGC Release: Release 7 and later.
Chapter 1 Billing Interfaces CDE Detail Description Egress SigPath ID (Tag: 4070) Table 1-116 Egress SigPath ID Description Form Name: Egress SigPath ID Tag: 4070 Source: MDL/Engine Description/Purpose: The egress SigPath ID is used to associate outgoing bearer channels with signaling services, such as a destination point code (DPC) in SS7. Format: BE Length in Octets: 4 Data Value: 32 bits of binary value Extended Data Value: No extended value.
Chapter 1 Billing Interfaces CDE Detail Description Egress Protocol ID (Tag: 4073) Table 1-119 Egress Protocol ID Description Form Name: Egress Protocol ID Tag: 4073 Source: MDL/Engine Description/Purpose: The egress Protocol ID is determined from MDL and is used in measurements and billing. On Release 9.7(3), for the H.248 Protocol feature, new protocol type: “10=H.248” is added to the definition.
Chapter 1 Billing Interfaces CDE Detail Description Maintenance Span ID (Tag: 4075) Table 1-121 Maintenance Span ID Description Form Name: Maintenance Span ID Tag: 4075 Source: MDL/Engine Description/Purpose: The maintenance Span ID is used for maintenance PRI bearer channels. A span is a grouping of bearer channels. Format: BE Length in Octets: 4 Data Value: 32 bits of binary value Extended Data Value: No extended value. General Information: MGC Release: Release 7 and later.
Chapter 1 Billing Interfaces CDE Detail Description Charge Band Number (Tag: 4078) Table 1-123 Charge Band Number Description Form Name: Charge Band Number Tag: 4078 Source: MDL/Engine Description/Purpose: Used for reporting Advice of Charge information. Format: BE Length in Octets: 1 Data Value: Integer containing the Charge Band Number: Range: 0-255. Extended Data Value: No extended value. General Information: MGC Release: Release 9.3(1) and later.
Chapter 1 Billing Interfaces CDE Detail Description Original Called Number (Tag: 4080) Table 1-125 Original Called Number Description Form Name: Original Called Number Tag: 4080 Source: MDL Description/Purpose: This tag contains the digits from the original called party number. Format: IA5 Length in Octets: 1-96 Data Value: The digits of the original called party number. Extended Data Value: No extended value.
Chapter 1 Billing Interfaces CDE Detail Description Charge Unit Number (Tag: 4082) Table 1-127 Charge Unit Number Description Form Name: Charge Unit Number Tag: 4082 Source: MDL Description/Purpose: Used for reporting Advice of Charge information. Format: BE Length in Octets: 1 Data Value: Comprised of an integer containing the Charge Unit Number, provisioned as part of the Dial Plan provisioning ANSI/ITU Variations: None Valid Range: 0-255 Extended Data Value: No extended value.
Chapter 1 Billing Interfaces CDE Detail Description Outgoing Calling Party Number (Tag: 4084) Table 1-129 Outgoing Calling Party Number Description Form Name: Outgoing Calling Party Number Tag: 4084 Source: MDL Description/Purpose: The Calling Party Number being sent out on line by the Cisco MGC is recorded in this tag. This value may be different from the received Calling Party Number. The received Calling Party Number may be modified either because of Generic Number or in Generic Analysis.
Chapter 1 Billing Interfaces CDE Detail Description MCID Response Indicator (Tag: 4086) Table 1-131 MCID Response Indicator Description Form Name: MCID Response Indicator Tag: 4086 Source: MDL Description/Purpose: Allows the carrier to determine whether MCID is included or not. Format: BE Length in Octets: 1 Data Value: MCID Response Indicator information is 1 bit and is defined as follows: 0 1 MCID not included MCID included Extended Data Value: No extended value.
Chapter 1 Billing Interfaces CDE Detail Description Network Translated Address Indicator (Tag: 4089) Table 1-134 Network Translated Address Indicator Description Form Name: Network Translated Address Indicator Tag: 4089 Source: MDL Description/Purpose: Information sent in the forward direction to indicate whether network translation of the called address has occurred. This indicator is specific to BTNUP, UK IUP, and UK ISUP. This allows you to determine whether a number has been translated.
Chapter 1 Billing Interfaces CDE Detail Description Reservation Request Error Count (Tag: 4091) Table 1-136 Reservation Request Error Count Description Form Name: Reservation Request Error Count Tag: 4091 Source: MDL Description/Purpose: This tag is present if the Resource Reservation Lost event was received during a call. It will be a count of the number of times the event occurred during the call.
Chapter 1 Billing Interfaces CDE Detail Description ATM Egress Configured Profile (Tag: 4093) Table 1-138 ATM Egress Configured Profile Description Form Name: ATM Egress Configured Profile Tag: 4093 Source: MDL Description/Purpose: This tag is present if an ATM profile was configured based on Service Level Agreement (SLA) for Egress call leg.
Chapter 1 Billing Interfaces CDE Detail Description ATM Negotiated Profile (Tag: 4094) Table 1-139 ATM Negotiated Profile Description Form Name: ATM Negotiated Profile Tag: 4094 Source: MDL Description/Purpose: This tag is present if an ATM profile was negotiated based on Service Level Agreement (SLA). Format: IA5 Length in Octets: 1-16 Data Value: ITU 1 ITU 2 ITU 3 ITU 7 ITU 8 ITU 12 Custom 100 Custom 101 Custom 110 Custom 200 ANSI/ITU Variations: None Extended Data Value: No extended value.
Chapter 1 Billing Interfaces CDE Detail Description Route Name (Tag: 4096) Table 1-141 Route Name Description Form Name: Route Name Tag: 4096 Source: Engine Description/Purpose: Route Name being used for the call. Format:IA5 Length in Octets: 1 to 20 Data Value: ASCII name of the route being used. Extended Data Value: No extended value. General Information: MGC Release: Release 9.5(2) and later.
Chapter 1 Billing Interfaces CDE Detail Description Originating Leg DSP Statistics (Tag: 4098) Table 1-143 Originating Leg DSP Statistics Description Form Name: Originating Leg DSP Statistics Tag: 4098 Source: Engine Description/Purpose: Provides DSP statistics for the originating leg of the call. On Release 9.7(3), the H.248 Protocol feature is added. Because for H.248 DSP statistics in CDR are not supported, this tag is not logged in to CDR for the H.248 leg.
Chapter 1 Billing Interfaces CDE Detail Description Table 1-143 Originating Leg DSP Statistics Description Form (continued) Extended Data Value: No extended value. General Information: This CDE is populated when an originating endpoint is controlled by the Cisco MGC software through the MGCP protocol and the associated MGCP media gateway is enabled to send DSP statistics to the Cisco MGC.
Chapter 1 Billing Interfaces CDE Detail Description Terminating Leg DSP Statistics (Tag: 4099) Table 1-144 Terminating Leg DSP Statistics Description Form Name: Terminating Leg DSP Statistics Tag: 4099 Source: Engine Description/Purpose: Provides DSP statistics for the terminating leg of the call. On Release 9.7(3), the H.248 Protocol feature is added. Because for H.248 DSP statistics in CDR are not supported, this tag is not logged in to CDR for the H.248 leg.
Chapter 1 Billing Interfaces CDE Detail Description Originating Remote SIP Host (Tag: 4201) Table 1-145 Originating Remote SIP Host Description Form Name: Originating Remote SIP Host Tag: 4201 Source: MDL/Engine Description/Purpose: Formerly named as Ingress SIP URL. Contains the remote host for the originating side of a SIP-originated call (this tag is present only if SIP appears on the originating side of the call).
Chapter 1 Billing Interfaces CDE Detail Description Source IP Address (Tag: 4204) Table 1-148 Source IP Address Description Form Name: Source IP Address Tag: 4204 Source: MDL Description/Purpose: Identifies the source that sends the call setup message in incoming SIP and H.323 calls. Format: IA5 (string) Length in Octets: 1 to 23 Data Value: IPV4 format. Example: 10.1.22.115. Extended Data Value: No extended value.
Chapter 1 Billing Interfaces CDE Detail Description Egress Media Device Address (Tag: 4206) Table 1-150 Egress Media Device Address Description Form Name: Engress Media Device Address Tag: 4206 Source: MDL Description/Purpose: Identifies the IP address of the terminating RTP end point. This is parsed from the SDP from SIP, MGCP, or EISUP (HSI). Format: IA5 (string) Length in Octets: 1 to 256 Data Value: IPV4 format or FQDN. Examples: 10.1.22.115, sp-46-39-gateway.customer.com.
Chapter 1 Billing Interfaces CDE Detail Description Final Codec (Tag: 4208) Table 1-152 Final Codec Description Form Name: Final Codec Tag: 4208 Source: MDL Description/Purpose: Identifies the final codec used for the connection (the RTP stream). This is parsed from the SDP from SIP or MGCP. Format: IA5 (string) Length in Octets: 1 to 12 Data Value: String.
Chapter 1 Billing Interfaces CDE Detail Description Originating VPN ID (Tag: 4211) Table 1-155 Originating VPN ID Description Form Name: Originating VPN ID Tag: 4211 Source: MDL Description/Purpose: Identifies the VPN customer ID associated with the incoming trunk group or signaling service. It is used for feature transparency with access protocols DPNSS and QSIG. Format: IA5 Length in Octets: 8 Data Value: Alphanumeric string. It is associated with DPNSS and QSIG trunk groups.
Chapter 1 Billing Interfaces CDE Detail Description Meter Pulses Received (Tag: 4213) Table 1-157 Meter Pulses Received Description Form Name: Meter Pulses Received Tag: 4213 Source: MDL Description/Purpose: Contains the total number of meter pulses received at the terminating side of the call. Format: BE Length in Octets: 4 32 Data Value: Integer value in the range: 0 to 2 -1 Extended Data Value: No extended value. General Information: MGC Release: Release 9.5(2) and later.
Chapter 1 Billing Interfaces CDE Detail Description Charge Tariff Info (Tag: 4215) Table 1-159 Charge Tariff Info Description Form Name: Charge Tariff Info Tag: 4215 Source: MDL Description/Purpose: Contains Charging Tariff Information that has been sent or received in MPM messages. It comprises the following data items: • tariff type sent • tariff type received • tariff id (timestamped) – may be repeated (up to 11 occurrences).
Chapter 1 Billing Interfaces CDE Detail Description Short Call Indicator (Tag: 4217) Table 1-161 Short Call Indicator Description Form Name: Short Call Indicator Tag: 4217 Source: MDL Description/Purpose: Used to indicate that a call was a short duration call. Format: BE Length in Octets: 1 Data Value: 1 = Short Call. Extended Data Value: No extended value. General Information: The actual period for the timer used to identify short duration calls is configurable between 1 and 30 seconds.
Chapter 1 Billing Interfaces CDE Detail Description Call Recovered Indication (Tag: 4219) Table 1-163 Call Recovered Indication Description Form Name: Call Recovered Indication Tag: 4219 Source: MDL Description/Purpose: Indicates that the call was recovered by the standby MGC host following an automatic switchover and may have been released. Format: BE Length in Octets: 1 Data Value: 1 = Call Recovered 2 = Call Recovered and Released Extended Data Value: No extended value.
Chapter 1 Billing Interfaces CDE Detail Description Service Activation (Tag: 4221) Table 1-165 Service Activation Description Form Name: Service Activation Tag: 4221 Source: MDL Description/Purpose: Allows the user to determine which supplementary services have been invoked by the user or MGC.
Chapter 1 Billing Interfaces CDE Detail Description PRI AOC – S Charge Information (Tag: 4223) Table 1-167 PRI AOC – S Charge Information Description Form Name: PRI AOC – S Charge Information Tag: 4223 Source: MDL Description/Purpose: Contains Charging Tariff Information that has been setup for AOC – S Supplementary services. It comprises the following data items: • tariff id and timestamped (from octet 1–6) may be repeated (up to 11 occurrences).
Chapter 1 Billing Interfaces CDE Detail Description PRI AOC – E Charge Information (Tag: 4225) Table 1-169 PRI AOC – E Charge Information Description Form Name: PRI AOC – E Charge Information Tag: 4225 Source: MDL Description/Purpose: Contains Charging Tariff Information that has been setup for AOC – E Supplementary services. It comprises the following data items: • tariff id and timestamped (from octet 5–10) may be repeated (up to 11 occurrences).
Chapter 1 Billing Interfaces CDE Detail Description Route Optimization/Path Replacement Action (Tag: 4227) Table 1-171 ‘Route Optimization/Path Replacement Action Name: RO/PR EXECUTED Tag: 4227 Source: MDL Description/Purpose: Indicates that the RO or PR service has resulted in the replacement of media channels. Format: Integer Length in Octets: 1 Data Value: RO/PR operation = 1 indicates RO/PR feature invocation. RO/PR operation = 2 indicates receipt of RO/PR feature invocation.
Chapter 1 Billing Interfaces CDE Detail Description Route Optimization/Path Replacement Trunk Group Info (Tag: 4229) Table 1-173 Route Optimization/Path Replacement Trunk Group Info Name: RO/PR Replacement Trk Group Tag: 4229 Source: MDL Description/Purpose: Indicates the trunk group id of the new replaced media channel associated with the slave call reference. Format: Integer Length in Octets: 2 Data Value: See CDE 4008 for more information. ANSI/ITU Variations: None.
Chapter 1 Billing Interfaces CDE Detail Description Table 1-175 Route Optimization Switchover Timestamp (continued) Extended Data Value: No extended value. General Information: MGC Release: Release 9.6(1) and later. Rejecting Location Label (Tag: 4232) Table 1-176 Rejecting Location Label Description Form Name: Rejecting Location Label Tag: 4232 Source: MDL Description/Purpose: Name of the Call-limiting location label which caused the call rejection.
Chapter 1 Billing Interfaces CDE Detail Description Table 1-177 Rejecting Location Label Direction Form (continued) Extended Data Value: No extended value. General Information: For calls with location labels defined, a call admission check must be made once the terminating side is set up. This involves reading internal tables to get call limit data and active call counter data. If the call limit threshold is reached, then the call is rejected against that location label.
Chapter 1 Billing Interfaces CDE Detail Description Table 1: Name: H323 Destination Tag: 4236 Source: MDL Description/Purpose: Identifieds the H323 Destination Address associated with the terminal trunk group or sigPath. Format: IA5 Length in Octet: 1 to 29 Data Value: Content: [IP Address]:[Port] Extended Data Value: No extended value. General Information: This destination address is used to indicate the H323 address that was used in Non-RAS mode.
Chapter 1 Billing Interfaces CDE Detail Description Ingress Redirecting Number (Tag 4237) Table 1-181 Ingress Redirecting Number Description Form Name: Ingress Redirecting Number Tag: 4237 Source: MDL/Engine Description/Purpose: This CDE records the digits from the redirecting number received by the MGC. Format: IA5 Length in Octet: 1 Data Value: Character string containing the forwarded station’s address or subscriber number. Extended Data Value: No extended value.
Chapter 1 Billing Interfaces CDE Detail Description CNAM DIP (Tag 4240) Table 1-183 CNAM DIP Description Form Name: CNAM DIP Tag: 4240 Source: MDL Description/Purpose: This feature indicates whether a called party has subscribed to the Calling Name Delivery (CNAM) feature. The feature allows the name of the calling party to be delivered to the called party. Format: Structured Variable Length in Octet: 2 Data Value: Indicates whether the CNAM feature is invoked by the called party.
Chapter 1 Billing Interfaces CDE Detail Description Terminating Remote SIP Host (Tag 4242) Table 1-185 Terminating Remote SIP Host Description Form Name: Terminating Remote SIP Host Tag: 4242 Source: MDL/Engine Description/Purpose: Contains the remote host (the To Host for a SIP call when sending a REQUEST from the PGW on the terminating side) for the terminating side of a call.
Chapter 1 Billing Interfaces CDE Detail Description License Rejecting Direction (Tag 4245) Table 1-188 License Rejecting Direction Description Form Name: License Rejecting Direction Tag: 4245 Source: MDL Description/Purpose: Indication of whether the call rejection was due to a license violation from incoming or outgoing traffic to the PGW. Format: BE Length in Octet: 1 Data Value: 1 = Inbound (PGW originating side) 2 = Outbound (PGW terminating side) Extended Data Value: No extended value.
Chapter 1 Billing Interfaces CDE Detail Description SIP Routing URI Source (Tag 4247) Table 1-190 SIP Routing URI Source Description Form Name: SIP Routing URI Source Tag: 4247 Source: MDL/Engine Description/Purpose: Indicates which header or URL was used to make routing decisions. Format: Integer Length in Octet: 1 Data Value: 1 = Top Route: header 2 = Request URL 3 = To: Header Extended Data Value: No extended value.
Chapter 1 Billing Interfaces CDE Detail Description Millisecond Granularity CDEs IAM Timepoint Received_ms (Tag: 4100) Table 1-192 IAM Timepoint Received_ms Description Form Name: IAM Timepoint Received_ms Tag: 4100 Source: MDL/Engine Description/Purpose: The IAM timepoint received is the recorded timepoint when the IAM was received, in milliseconds since 1970. Format: Binary Length in Octets: 6 Data Value: Cisco MGC time plus 2 bytes for milliseconds Extended Data Value: No extended value.
Chapter 1 Billing Interfaces CDE Detail Description ACM Timepoint Sent_ms (Tag: 4103) Table 1-195 ACM Timepoint Sent_ms Description Form Name: ACM Timepoint Sent_ms Tag: 4103 Source: MDL/Engine Description/Purpose: The ACM timepoint sent is the recorded timepoint when the ACM was sent, in milliseconds since 1970. Format: Binary Length in Octets: 6 Data Value: Cisco MGC time plus 2 bytes for milliseconds. Extended Data Value: No extended value. General Information: MGC Release: Release 7.
Chapter 1 Billing Interfaces CDE Detail Description First REL Timepoint_ms (Tag: 4106) Table 1-198 First REL Timepoint_ms Description Form Name: First REL Timepoint_ms Tag: 4106 Source: MDL/Engine Description/Purpose: Timepoint for receipt of first REL/RELEASE. Format: Binary Length in Octets: 6 Data Value: Cisco MGC time plus 2 bytes for milliseconds. Extended Data Value: No extended value. General Information: MGC Release: Release 7.0 and later.
Chapter 1 Billing Interfaces CDE Detail Description RLC Timepoint Sent_ms (Tag: 4109) Table 1-201 RLC Timepoint Sent_ms Description Form Name: RLC Timepoint Sent_ms Tag: 4109 Source: MDL/Engine Description/Purpose: Recorded timepoint when the RLC was sent, in milliseconds since 1970. Format: Binary Length in Octets: 6 Data Value: Cisco MGC time plus 2 bytes for milliseconds. Extended Data Value: No extended value. General Information: MGC Release: Release 7.0 and later.
Chapter 1 Billing Interfaces CDE Detail Description Cisco Reserved CDEs Unique Call Correlator ID (Tag: 5000) Table 1-202 Unique Call Correlator ID Description Form Name: Unique Call Correlator ID Tag: 5000 Source: MDL/Engine/External Description/Purpose: A Unique Call ID can be created by an MGC or a media gateway, depending on the origin of a call.
Chapter 1 Billing Interfaces CDE Detail Description Miscellaneous Fields MGC ID (Tag: 6000) Table 1-203 MGC ID Description Form Name: MGC ID Tag: 6000 Source: CDR Dumper Description/Purpose: Indicates the MGC ID on which the CDR file was created. Format: IA5 Length in Octets: 1-32 Data Value: IA5 string Extended Data Value: No extended value. General Information: This field is used (only) by the CDR dumper to generate the file header CDB record and the file footer CDB record.
Chapter 1 Billing Interfaces CDE Detail Description Total Number of CDB Records (Tag: 6003) Table 1-206 Total Number of CDB Records Description Form Name: Total Number of CDB Records Tag: 6003 Source: CDR Dumper Description/Purpose: Indicates the total number of CDB records included in the CDR file. Format: BE Length in Octets: 4 Data Value: UNIX time format (number of seconds since January 1, 1970). Extended Data Value: No extended value.
Chapter 1 Billing Interfaces CDE Detail Description Protocol Specific CDEs NTT TTC Contract Number (Tag: 6100) Table 1-209 TTC Contract Number Description Form Name: TTC Contract Number Tag: 6100 Source: MDL Description/Purpose: Digits from the Contract Number Parameter of TTC-Q763a. Format: IA5 Length in Octets: 3 to 12 Data Value: Digits Extended Data Value: No extended value. General Information: This field is used (only) when the Cisco MGC is configured with the TTC signaling protocol.
Chapter 1 Billing Interfaces CDE Detail Description TTC Charge Info Type (Tag: 6103) Table 1-212 TTC Charge Info Type Description Form Name: TTC Charge Info Type Tag: 6103 Source: MDL Description/Purpose: This parameter is taken from the TTC-Q.763a Charge Information parameter. Format: IA5 Length in Octets: 3 to n, where the field configuration is specified separately for each network Data Value: Sequence of octets Extended Data Value: No extended value.
CH A P T E R 2 MGC Info Field Reference This chapter provides additional information about the MGC Info Field (Tag 4031), described in Chapter 1, “Billing Interfaces” The MGC info field consists of several subfields, that are stored in the value section of the VSC info field. These subfields contain no tags or values. The MGC Info field provides the customer with backward compatibility to Cisco MGC Software Release 5.0 and earlier.
Chapter 2 MGC Info Subfields Table 2-1 MGC Info Subfields (continued) Location (Position) Size This is the numeric representation 0 = ISDN PRI of the protocol family for the 1 = C7 originating side 2 = DPNSS 3 = CAS 4 = ASN 5 = Unknown Binary Big-endian 10 1 Call Type Flag This indicates whether the call was a real or virtual call [used primarily in DPNSS] 0 = Real call 1 = Virtual Call Binary Big-endian 11 1 Call Feature Flag 0 = Normal Call This indicates whether the call was a normal call o
Chapter 2 MGC Info Subfields Table 2-1 MGC Info Subfields (continued) Location (Position) Size 1 = Unknown Language 2 = English 3 = Russian 4 = French 5 = German 6 = Spanish 18 1 0 = Unknown User 1 = Subscriber User 2 = Operator 3 = Pay phone 4 = EMERGENCY 5 = NETWORK 6 = ATT PR1 7 = ATT PR2 8 = ATT PR3 9 = ATT PR4 10 = ATT PR5 11 = CGSUB PR2 12 = CGSUB PR3 13 = CGSUB PR4 14 = CGSUB PR5 15 = SERVICE LINE 16 = DPNSS 17 = CONF DEVICE 18 = ALARM DEVICE 19 = PAYPHONE TYPE2 20 = PAYPHONE TYPE3 21 = PAYPH
Chapter 2 MGC Info Subfields Cisco Media Gateway Controller Software Release 9 Billing Interface Guide 2-4 OL-1089-11
A P P E N D I X A CDE Listings by Release This appendix lists the valid call detail elements (CDEs) on a release-by-release basis. The valid CDEs are listed in the following sections: • CDE Baseline—Release 9.1(5) and Higher, page A-1 • CDE Changes in Release 9.2(2), page A-4 • CDE Changes in Release 9.3(1), page A-5 • CDE Changes in Release 9.3(2), page A-5 • CDE Changes in Release 9.4(1), page A-5 • CDE Changes in Release 9.5(2), page A-6 • CDE Changes in Release 9.
Appendix CDE Baseline—Release 9.1(5) and Higher Table A-1 Valid CDEs for Release 9.
Appendix CDE Baseline—Release 9.1(5) and Higher Table A-1 Valid CDEs for Release 9.
Appendix CDE Changes in Release 9.2(2) Table A-1 Valid CDEs for Release 9.
Appendix CDE Changes in Release 9.3(1) CDE Changes in Release 9.3(1) Table A-2 lists the CDEs that are valid as of Release 9.3(1). Table A-2 CDE Changes in Release 9.3(1) Tag Value Field Name Action 4078 Charge Band Number Added 4079 Furnish Charging Information Added 4080 Original Called Number Added CDE Changes in Release 9.3(2) Table A-3 lists the CDEs that are valid as of Release 9.3(2). Table A-3 CDE Changes in Release 9.
Appendix CDE Changes in Release 9.5(2) Table A-4 CDE Changes in Release 9.
Appendix CDE Changes in Release 9.6(1) Table A-5 CDE Changes in Release 9.
Appendix CDE Changes in Release 9.7 Table A-6 CDE Changes in Release 9.6(1) (continued) Tag Value Field Name Action 4098 Originating Leg DSP Statistics Modified for the Support of DSP Voice Quality Statistics feature, in patch CSCOnn026. 4099 Terminating Leg DSP Statistics Modified for the Support of DSP Voice Quality Statistics feature, in patch CSCOnn026. 4221 Service Activation Modified, added new data values.
Appendix CDE Changes in Release 9.7 Table A-7 CDE Changes in Release 9.7 Tag Value Field Name Action 4097 MGCP Script Response String Modified for the H.248 Protocol feature 4098 Originating Leg DSP Statistics Modified for the H.248 Protocol feature 4099 Terminating Leg DSP Statistics Modified for the H.248 Protocol feature 4201 Ingress SIP URL Name changed to Originating Remote SIP Host. 4202 Egress SIP URL Name changed to Originating Local SIP Host.
Appendix CDE Changes in Release 9.
INDEX A ACM Timepoint Sent_ms (Tag: 4103) AMA Line Number (Tag: 4050) 1-159 Announcement ID (Tag: 4044) C-CPC Language 2-3 CDB 1-99 2-3 1-9 CDB call data element fields ANM Timepoint Received_ms (Tag: 4104) ANM Timepoint Sent_ms (Tag: 4105) 2-2 C-CPC User 1-115 ANM/Answer Timepoint (Tag: 4005) C-CPC Call Type 1-159 CDB message type 1-159 1-2 CDB Timepoint (Tag: 4001) 1-112 CDB Version (Tag: 4000) CDE description form CDR B 1-6 1-98 1-98 1-48 1-9 See call detail record file billi
Index obtaining related publications related publications i-xv J i-xvi Jurisdiction Information Parameter (Tag: 2016/ANSI) 1-64 E Egress destination Point Code (Tag: 4037) Egress Media Gateway ID (Tag: 4039) 1-110 Egress originating Point Code (Tag: 4036) Egress Packet Info (Tag: 4047) L 1-109 LNP Dip (Tag: 4029) 1-109 1-105 LRN Nature of Address (Tag: 2006/ANSI) 1-114 LRN Nature of Address (Tag: 3006/ITU) LRN Number (Tag: 4013) 1-55 1-73 1-102 F File End Time (Tag: 6002) File Start Time
Index Transit Network Selection (Tag O \ 2013/ANSI) Originating Gateway Primary Select (Tag: 4052) 1-136 Originating Line Information (Tag \ 3002/ITU) 1-70 1-51 1-93 1-165 TTC Contract Number (Tag: 6100) Originating Member (Tag: 4009) 1-165 TTC Contract Number NOA (Tag: 6101) 1-165 1-101 Originating Trunk Group (Tag: 4008) 1-100 U 2-2 Out Signal path ID Transit Network Selection (Tag: 3013/ITU) TTC Charge Info (Tag: 6102 Originating Line Information (Tag: 2002/ANSI) Out protocol ID 1-
Index Cisco Media Gateway Controller Software Release 9 Billing Interface Guide IN-4 OL-1089-11
