Cisco Aironet 1000 Series Lightweight Access Point Hardware Installation Guide April 2007 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
C O N T E N T S Preface vii Audience vii Purpose vii Organization vii Conventions viii Related Publications x Finding the Product Serial Number xi Obtaining Documentation, Obtaining Support, and Security Guidelines xii CHAPTER 1 Overview 1-1 Guidelines for Using the Access Points 1-2 Hardware Features 1-2 Single or Dual-Radio Operation 1-4 Antennas Supported 1-4 Ethernet Port 1-5 LEDs 1-5 Power Sources 1-5 UL 2043 Certification 1-6 Anti-Theft Features 1-6 Network Configuration Example 1-7 CHAPTER 2 In
Contents FCC Safety Compliance Statement 2-2 General Safety Guidelines 2-2 Warnings 2-2 Unpacking the Access Point 2-3 Package Contents 2-3 Basic Installation Guidelines 2-3 Before Beginning the Installation 2-4 Access Point Layout and Connectors 2-5 Controller Discovery Process 2-6 Deploying the Access Points on the Wireless Network 2-7 Mounting Overview 2-8 Mounting Access Points Using a Ceiling-Mount Base 2-10 Mounting Access Points Using the Ceiling-Mount Clips 2-11 Mounting the Access Point Using a Pr
Contents APPENDIX A Translated Safety Warnings A-1 APPENDIX B Declarations of Conformity and Regulatory Information B-1 Manufacturers Federal Communication Commission Declaration of Conformity Statement B-2 VCCI Statement for Japan B-3 Department of Communications—Canada B-4 Canadian Compliance Statement B-4 European Community, Switzerland, Norway, Iceland, and Liechtenstein B-5 Declaration of Conformity with Regard to the 1999/5/EC (R&TTE Directive) B-5 Declaration of Conformity for RF Exposure B-7 G
Contents APPENDIX C Access Point Specifications C-1 APPENDIX D Channels and Power Levels D-1 APPENDIX E Priming Access Points Prior to Deployment E-1 APPENDIX F Configuring DHCP Option 43 F-1 Overview F-2 Configuring Option 43 for 1000 Series Access Points F-3 Configuring Option 43 for 1100, 1130, 1200, 1240, and 1300 Series Access Points F-4 Cisco Aironet 1000 Series Lightweight Access Point Hardware Installation Guide vi OL-9403-04
Preface Audience This guide is for the networking professional who installs and manages the Cisco Aironet 1000 Series Lightweight Access Point, hereafter referred to as the access point. These access points are part of the Cisco Integrated Wireless Network Solution and require no manual configuration before they are mounted. The access point is automatically configured by a Cisco Wireless LAN Controller using the Lightweight Access Point Protocol (LWAPP).
Preface Conventions Appendix D, “Channels and Power Levels,” indicates how to access the document that lists the access point radio channels and the maximum power levels supported by the world’s regulatory domains. Appendix E, “Priming Access Points Prior to Deployment,” describes the procedure to pre-configure an access point with IP addresses and controller information. Appendix F, “Configuring DHCP Option 43,” describes the procedure to configure DHCP Option 43.
Preface Conventions Warning Waarschuwing This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. (To see translations of the warnings that appear in this publication, refer to the appendix “Translated Safety Warnings.”) Dit waarschuwingssymbool betekent gevaar.
Preface Related Publications ¡Advertencia! Este símbolo de aviso significa peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considerar los riesgos que entraña la corriente eléctrica y familiarizarse con los procedimientos estándar de prevención de accidentes. (Para ver traducciones de las advertencias que aparecen en esta publicación, consultar el apéndice titulado “Translated Safety Warnings.”) Varning! Denna varningssymbol signalerar fara.
Preface Finding the Product Serial Number Finding the Product Serial Number The access point serial number is on the right side of the housing (refer to Figure 1).
Preface Obtaining Documentation, Obtaining Support, and Security Guidelines Obtaining Documentation, Obtaining Support, and Security Guidelines For information on obtaining documentation, obtaining support, providing documentation feedback, security guidelines, and also recommended aliases and general Cisco documents, see the monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at: http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.
CH A P T E R 1 Overview The Cisco Aironet 1000 Series Lightweight Access Points (hereafter called access points) combine mobility and flexibility with the enterprise-class features required by networking professionals. These access points are part of the Cisco Integrated Wireless Network Solution and require no manual configuration before they are mounted.
Chapter 1 Overview Guidelines for Using the Access Points Guidelines for Using the Access Points You should keep these guidelines in mind when you use the access points: • The access points can only communicate with controllers and can not operate independently. • The access points communicate only with controllers and do not support Wireless Domain Services (WDS). The access points cannot communicate with WDS devices.
Chapter 1 Overview Hardware Features Figure 1-1 Access Point Configurations 146971 Power 2.4 GHz Alarm 5 GHz Alarm Power 5 GHz 2.4 GHz 1 1 2 2 Integrated antennas only (AIR-AP1010) Integrated antennas and external antenna connectors (AIR-AP1020 and AIR-AP1030) Figure 1-2 illustrates the left side connectors on the access point. Figure 1-2 Access Point Left Side Connectors 48 v 250Ma 1 2 3 Ethernet 146973 24 GHz Left 4 1 Security key slot 3 48-VDC power port 2 2.
Chapter 1 Overview Hardware Features Figure 1-3 illustrates the right side connectors on the access point. Access Point Right Side Connectors 5 GHz 24 GHz Right 1 2 1 5-GHz antenna connector (right) 2 Security key slot 3 3 146975 Figure 1-3 2.4-GHz antenna connector (right) Single or Dual-Radio Operation The access point supports single or simultaneous dual radio operation using a 2.4-GHz 802.11g radio and a 5-GHz 802.11a radio.
Chapter 1 Overview Hardware Features Table 1-1 lists the supported external antennas. Table 1-1 Supported External Antennas 2.4-GHz Antennas Gain (dBi) 5-GHz Antennas Gain (dBi) AIR-ANT5959 diversity omnidirectional 2.0 AIR-ANT5135D-R omnidirectional 3.5 AIR-ANT4941 dipole 2.2 AIR-ANT5160V-R omnidirectional 6.0 AIR-ANT1728 omnidirectional 5.2 AIR-ANT2506 omnidirectional 5.2 AIR-ANT3213 diversity omnidirectional 5.2 AIR-ANT1729 patch 6.0 AIR-ANT2012 diversity patch 6.
Chapter 1 Overview Hardware Features The access point supports the following power sources: • Power module (AIR-PWR-1000=) • Inline power: – Cisco Aironet 1000 series access point power injector (AIR-PWRINJ-1000AF=) – An inline power capable switch, such as the Cisco Catalyst 3550 PWR XL, 3560-48PS, 3570-48PS, 4500 with 802.3AF PoE module, or the 6500 with 802.3AF PoE module – Other inline power switches supporting the IEEE 802.
Chapter 1 Overview Network Configuration Example Network Configuration Example The access points support Layer 2 or Layer 3 network operation. In Layer 2 configurations, the access point and the controller are on the same subnet and communicate with encapsulated Ethernet frames using MAC addresses rather than IP addresses. Layer 2 configurations are typically not scalable into larger networks. Additionally, Layer 2 operation is supported only by the Cisco 4400 series controllers.
Chapter 1 Overview Network Configuration Example Figure 1-5 illustrates a typical Layer 2 network configuration. In a Layer 2 configuration, the controller and the access points are on the same subnet.
CH A P T E R 2 Installing the Access Point This chapter describes the installation of the access point and includes these sections: • Safety Information, page 2-2 • Warnings, page 2-2 • Unpacking the Access Point, page 2-3 • Basic Installation Guidelines, page 2-3 • Before Beginning the Installation, page 2-4 • Controller Discovery Process, page 2-6 • Controller Discovery Process, page 2-6 • Mounting Overview, page 2-8 • Securing the Access Point Using a Security Cable, page 2-17 • Conn
Chapter 2 Installing the Access Point Safety Information Safety Information Follow the guidelines in this section to ensure proper operation and safe use of the access point. FCC Safety Compliance Statement The FCC with its action in ET Docket 96-8 has adopted a safety standard for human exposure to radio frequency (RF) electromagnetic energy emitted by FCC certified equipment.
Chapter 2 Installing the Access Point Unpacking the Access Point Warning This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 20A Statement 1005 Unpacking the Access Point Follow these steps to unpack the access point: Step 1 Open the shipping container and carefully remove the contents. Step 2 Return all packing materials to the shipping container and save it.
Chapter 2 Installing the Access Point Before Beginning the Installation • Do not mount the access point outside of buildings. • Do not mount the access points on building perimeter walls unless outside coverage is desired. • When mounting an access point in the corner of a right-angle hallway intersection, mount the access point at a 45-degree angle to the two hallways (see Figure 2-1). The access point internal antennas are not omnidirectional and cover a larger area when mounted this way.
Chapter 2 Installing the Access Point Before Beginning the Installation Access Point Layout and Connectors Figure 2-2 illustrates the connectors on the left side of the access point. Figure 2-2 Access Point Left Side Connectors 48 v 250Ma 1 2 3 146973 24 GHz Left Ethernet 4 1 Security cable keyslot 6 48-VDC power port 2 2.4-GHz antenna connector (left) 7 Ethernet port (RJ-45) Figure 2-3 illustrates the right side of the access point.
Chapter 2 Installing the Access Point Controller Discovery Process Figure 2-4 illustrates the access point LEDs on the top of the unit. Figure 2-4 Access Point LEDs 5 GHz 2.4 GHz 3 4 Power 2 Alarm 1 146972 side A 1 5-GHz LED 3 Alarm LED 2 2.
Chapter 2 Installing the Access Point Deploying the Access Points on the Wireless Network • DHCP server discovery—Uses DHCP Option 43 to provide controller IP addresses to the access points. Cisco switches support a DHCP server option. For additional information, refer to the “Configuring DHCP Option 43” section on page F-1. • DNS server discovery—The access point uses the name CISCO-LWAPP-CONTROLLER. to discover the controller IP addresses from a DNS server.
Chapter 2 Installing the Access Point Mounting Overview e. Step 4 On power up, verify that the access point is associated to a controller and operating normally. The Power LED should be green, the Alarm LED should be off, and the radio LEDs should be blinking. For additional information, see the “Powering Up the Access Point” section on page 2-19. After all access points are deployed and operating correctly, ensure that a controller is not configured as a master controller.
Chapter 2 Installing the Access Point Mounting Overview • Metal flush-mount bracket (user orderable) for mounting the access point to a vertical wall (see Figure 2-6) • Ceiling-mount bezel kit (user orderable) for mounting the access point above a suspended ceiling tile. For additional information, refer to the Quick Start Guide: Ceiling Mount Bezels for Cisco Aironet 1000 Series Lightweight Access Points. Factory-Supplied Mounting Options A.
Chapter 2 Installing the Access Point Mounting Overview Mounting Access Points Using a Ceiling-Mount Base When you are mounting the access point to horizontal surface, such as the ceiling of a building, use the ceiling-mount base to mount the access point. The ceiling-mount base can also be used to mount the access point to a desktop or shelf.
Chapter 2 Installing the Access Point Mounting Overview Step 7 Attach the cables to the access point. Note Step 8 When the access point is powered up and is associated with a controller (Power LED is green, Alarm LED is off, and the radio LEDs are blinking), the access point is broadcasting its beacon. Repeat the these steps for each access point on a horizontal surface. After mounting all horizontal surface access points, return to deploying the access points, "Step 3-c" on page 2-7.
Chapter 2 Installing the Access Point Mounting Overview Step 3 Snap the ceiling-mount clips onto a suspended ceiling rail (see Figure 9). Ensure you leave enough space around the access point to plug the Ethernet cable, optional external antenna cable(s), optional power supply cable, and optional Kensington MicroSaver security cable into the sides of the access point.
Chapter 2 Installing the Access Point Mounting Overview Mounting the Access Point Using a Projection Wall Mount Bracket When you are mounting the access point out from a vertical wall (flat sides along the wall or hallway), use an optional factory-orderable projection-mount L-bracket (see Figure 2-6).
Chapter 2 Installing the Access Point Mounting Overview Attaching the Access Point to the Projection-Mount Bracket 135671 Figure 2-11 Step 7 Step 8 Attach the cables to the sides of the access point. The Ethernet cable, optional external antenna cable(s), optional power supply cable, and optional Kensington MicroSaver security cables can be routed through the large holes in the mounting bracket. Note Ensure that the cables are routed away from the access point integrated antennas.
Chapter 2 Installing the Access Point Mounting Overview Mounting the Access Point Using the Flush-Mount Bracket When mounting the access point against a vertical wall (flat side toward the inside of the building), use an optional factory-orderable flush-mount bracket. Follow these steps to mount the bracket and attach the access point: Step 1 Before proceeding, gently screw the two factory-supplied screws and spring washers into the bottom of the access point (see Figure 2-10).
Chapter 2 Installing the Access Point Mounting Overview Attaching the Access Point to the Flush-Mount Bracket 135672 Figure 2-12 Step 7 Step 8 Attach the cables to the sides of the access point (the Ethernet cable, optional external antenna cable(s), optional power supply cable, and optional Kensington MicroSaver security cable). Note Ensure that the cables are routed away from the access point integrated antennas.
Chapter 2 Installing the Access Point Securing the Access Point Using a Security Cable Securing the Access Point Using a Security Cable You can secure the access point by installing a standard security cable (such as the Kensington MicroSaver, model number 64068) into the access point security cable slot (see Figure 2-3). The security cable can be used with any of the mounting methods described in this guide provided the cable can be secured to a nearby immovable object.
Chapter 2 Installing the Access Point Connecting the Ethernet and Power Cables Note Some older switches and patch panels might not provide enough power to operate the access point. At power-up, if the access point is unable to determine that the power source can supply sufficient power, the access point automatically deactivates both radios to prevent an over-current condition. All access LEDs are off.
Chapter 2 Installing the Access Point Powering Up the Access Point Connecting to an Ethernet Network with Local Power Note If your access point is connected to in-line power, do not connect the power module to the access point. Follow these steps to connect the access point to an Ethernet LAN when you are using a local power source: Step 1 Connect a Category 5 Ethernet cable to the RJ-45 Ethernet connector labeled Ethernet on the access point (see Figure 2-13).
Chapter 2 Installing the Access Point Returning MAC Information Returning MAC Information When you have completed the access point deployment, return the access point MAC addresses and the access point locations on the access point location maps or floor plans to your network planner or manager. The network operators can use the MAC address and location information to create maps for precise wireless system management.
CH A P T E R 3 Troubleshooting This chapter provides troubleshooting procedures for basic problems with the access point. For the most up-to-date, detailed troubleshooting information, refer to the Cisco Technical Support and Documentation website at the following URL: http://www.cisco.com/en/US/products/hw/wireless/tsd_products_support_category_home.
Chapter 3 Troubleshooting Guidelines for Using the Access Points Guidelines for Using the Access Points You should keep these guidelines in mind when you use the access points: • The access points can only communicate with controllers and cannot operate independently. • The access points do not support Wireless Domain Services (WDS). The access points cannot communicate with WDS devices. However, the controller provides functionality equivalent to WDS when the access point associates to it.
Chapter 3 Troubleshooting Checking the Access Point LEDs Checking the Access Point LEDs If your access point is not working properly, check the access point LEDs on the top of the unit. You can use the LED indications to quickly assess the unit’s status. Figure 3-1 shows the access point LEDs (for additional information refer to the Event Log using the access point browser interface). Figure 3-1 Access Point LEDs 5 GHz 2.4 GHz 3 4 Power 2 Alarm 1 146972 side A 1 5-GHz LED 3 Alarm LED 2 2.
Chapter 3 Troubleshooting Checking the Access Point LEDs The LED signals are listed in Table 3-1. Table 3-1 Access Point LED Signals Power LED Alarm LED 2.4 GHz LED 5 GHz LED Meaning Off Off Off No power or insufficient power. Off Check the power source and ensure that sufficient power is supplied to the access point. See Low Power Condition, page 3-5. Off Red Off Off Power applied and access point powering up (typical 10-20 seconds).
Chapter 3 Troubleshooting Low Power Condition Low Power Condition Warning This product must be connected to a Power over Ethernet (PoE) IEEE 802.3af compliant power source or an IEC60950 compliant limited power source. Statement 353 The access point can be powered from the 48-VDC power module or from an in-line power source. The access point supports the IEEE 802.3af power standard for in-line power sources. For operation, the access point (powered device) requires 12 W of input power.
Chapter 3 Troubleshooting Low Power Condition Cisco Aironet 1000 Series Lightweight Access Point Hardware Installation Guide 3-6 OL-9403-04
A P P E N D I X A Translated Safety Warnings For translated safety warnings, refer to the safety warning document that shipped with your access point or that is available on Cisco.com. To browse to the document on Cisco.com, follow these steps: Step 1 Click this link to the Cisco Wireless documentation home page: http://www.cisco.com/en/US/products/hw/wireless/tsd_products_support_category_home.html Step 2 Click Cisco Aironet 1000 Series listed under Wireless LAN Access.
Appendix A Translated Safety Warnings Cisco Aironet 1000 Series Lightweight Access Point Hardware Installation Guide A-2 OL-9403-04
A P P E N D I X B Declarations of Conformity and Regulatory Information This appendix provides declarations of conformity and regulatory information for the Cisco Aironet 1000 Series Lightweight Access Points.
Appendix B Manufacturers Federal Communication Commission Declaration of Conformity Statement Declarations of Conformity and Regulatory Information Manufacturers Federal Communication Commission Declaration of Conformity Statement Tested To Comply With FCC Standards FOR HOME OR OFFICE USE Model: AIR-AP1010-A-K9 / AIR-AP1020-A-K9 / AIR-AP1030-A-K9 AIR-AP1010-B-K9 / AIR-AP1020-B-K9 / AIR-AP1030-B-K9 FCC Certification number: LDK102057 Manufacturer: Cisco Systems, Inc.
Appendix B Declarations of Conformity and Regulatory Information VCCI Statement for Japan Caution Within the 5.15 to 5.25 GHz band (5 GHz radio channels 34 to 48) the U-NII devices are restricted to indoor operations to reduce any potential for harmful interference to co-channel Mobile Satellite System (MSS) operations. VCCI Statement for Japan Warning This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI).
Appendix B Declarations of Conformity and Regulatory Information Industry Canada Industry Canada Model: AIR-AP1010-A-K9 / AIR-AP1020-A-K9 / AIR-AP1030-A-K9 AIR-AP1010-B-K9 / AIR-AP1020-B-K9 / AIR-AP1030-B-K9 Certification number: 2461B-102057 Canadian Compliance Statement This Class B Digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numerique de la classe B respecte les exigences du Reglement sur le material broilleur du Canada.
Appendix B Declarations of Conformity and Regulatory Information European Community, Switzerland, Norway, Iceland, and Liechtenstein European Community, Switzerland, Norway, Iceland, and Liechtenstein Model: AIR-AP1010-E-K9 / AIR-AP1020-E-K9 / AIR-AP1030-E-K9 Declaration of Conformity with Regard to the 1999/5/EC (R&TTE Directive) This declaration is only valid for configurations (combinations of software, firmware, and hardware) provided and supported by Cisco Systems.
Appendix B Declarations of Conformity and Regulatory Information European Community, Switzerland, Norway, Iceland, and Liechtenstein This device complies with the EMC requirements (EN 60601-1-2) of the Medical Directive 93/42/EEC. For 2.4 GHz radios, the following standards were applied: Note Caution • Radio: EN 300.328-1, EN 300.328-2 • EMC: EN 301.489-1, EN 301.489-17 • Safety: EN 60950 This equipment is intended to be used in all EU and EFTA countries.
Appendix B Declarations of Conformity and Regulatory Information Declaration of Conformity for RF Exposure For 54 Mbps, 5 GHz access points, the following standards were applied: • Radio: EN 301.893 • EMC: EN 301.489-1, EN 301.489-17 • Safety: EN 60950 The following CE mark is affixed to the access point with a 2.4 GHz radio and a 54 Mbps, 5 GHz radio: Declaration of Conformity for RF Exposure The radio has been found to be compliant to the requirements set forth in CFR 47 Sections 2.
Appendix B Declarations of Conformity and Regulatory Information Guidelines for Operating Cisco Aironet Access Points in Japan Guidelines for Operating Cisco Aironet Access Points in Japan This section provides guidelines for avoiding interference when operating Cisco Aironet access points in Japan. These guidelines are provided in both Japanese and English.
Appendix B Declarations of Conformity and Regulatory Information Administrative Rules for Cisco Aironet Access Points in Taiwan Administrative Rules for Cisco Aironet Access Points in Taiwan This section provides administrative rules for operating Cisco Aironet access points in Taiwan. The rules are provided in both Chinese and English. Access Points with IEEE 802.11a Radios Chinese Translation English Translation This equipment is limited for indoor use.
Appendix B Declarations of Conformity and Regulatory Information Administrative Rules for Cisco Aironet Access Points in Taiwan All Access Points Chinese Translation English Translation Administrative Rules for Low-power Radio-Frequency Devices Article 12 For those low-power radio-frequency devices that have already received a type-approval, companies, business units or users should not change its frequencies, increase its power or change its original features and functions.
Appendix B Declarations of Conformity and Regulatory Information Declaration of Conformity Statements Declaration of Conformity Statements All the Declaration of Conformity statements related to this product can be found at the following URL: http://www.ciscofax.
Appendix B Declarations of Conformity and Regulatory Information Declaration of Conformity Statements for European Union Countries Cisco Aironet 1000 Series Lightweight Access Point Hardware Installation Guide B-12 OL-9403-04
Appendix B Declarations of Conformity and Regulatory Information Declaration of Conformity Statements for European Union Countries Cisco Aironet 1000 Series Lightweight Access Point Hardware Installation Guide OL-9403-04 B-13
Appendix B Declarations of Conformity and Regulatory Information Declaration of Conformity Statements for European Union Countries Cisco Aironet 1000 Series Lightweight Access Point Hardware Installation Guide B-14 OL-9403-04
A P P E N D I X C Access Point Specifications Table C-1 lists the technical specifications for the Cisco Aironet 1000 Series Lightweight Access Point. Table C-1 Access Point Specifications Specifications Category 802.11b 802.11g 802.11a Size 5.7 in. W x 1.6 in. D x 9.6 in. H 24.4 cm W x 4.1 cm D x 24.4 cm H Indicators Four indicators on the top of the unit: Power, Alarm, 2.4 GHz, 5 GHz. Connectors Right side: 5-GHz RP-TNC antenna connector, 2.4-GHz RP-TNC antenna connector Left side: 2.
Appendix C Table C-1 Access Point Specifications Access Point Specifications (continued) Specifications Category 802.11b 802.11g 802.11a Power output settings CCK OFDM OFDM 100, 50, 12.5, and 6.25 percent settings on the controller 100 mW (20 dBm) conducted 50 mW (17 dBm) conducted Maximum output power depends on the regulatory domain in which the access point is installed Antenna AIR-AP1010 • Two integrated 6 dBi patch antennas (2.
Appendix C Access Point Specifications Table C-1 Access Point Specifications (continued) Specifications Category 802.11b 802.11g 802.11a EMI and Susceptibility FCC Part 15.107 and 15.109 ICES-003 (Canada) EN 55022 EN 60601-1-2:2001 VCCI EN 301.489-1 EN 301.489-17 EN 55022 EN 55024 RF Exposure OET-65C RSS-102 ANSI C95.
Appendix C Access Point Specifications Cisco Aironet 1000 Series Lightweight Access Point Hardware Installation Guide C-4 OL-9403-04
Appendix C Table C-1 Access Point Specifications Access Point Specifications (continued) Specifications Category 802.11b 802.11g 802.11a Power output settings CCK OFDM OFDM 100, 50, 12.5, and 6.25 percent settings on the controller 100 mW (20 dBm) conducted 50 mW (17 dBm) conducted Maximum output power depends on the regulatory domain in which the access point is installed Antenna AIR-AP1010 • Two integrated 6 dBi patch antennas (2.
Appendix C Access Point Specifications Table C-1 Access Point Specifications (continued) Specifications Category 802.11b 802.11g 802.11a EMI and Susceptibility FCC Part 15.107 and 15.109 ICES-003 (Canada) EN 55022 EN 60601-1-2:2001 VCCI EN 301.489-1 EN 301.489-17 EN 55022 EN 55024 RF Exposure OET-65C RSS-102 ANSI C95.
Appendix C Access Point Specifications Cisco Aironet 1000 Series Lightweight Access Point Hardware Installation Guide C-4 OL-9403-04
A P P E N D I X D Channels and Power Levels For channel and maximum power level settings, refer to the Channels and Maximum Power Settings for Cisco Aironet Lightweight Access Points and Bridges document available on the Cisco Wireless documentation page of Cisco.com. To browse to the document, follow these steps: Step 1 Click this link to the Cisco Wireless documentation home page: http://www.cisco.com/en/US/products/hw/wireless/tsd_products_support_category_home.
Appendix D Channels and Power Levels Cisco Aironet 1000 Series Lightweight Access Point Hardware Installation Guide D-2 OL-9403-04
A P P E N D I X E Priming Access Points Prior to Deployment This section describes an optional procedure designed to prime or stage your access points in a convenient location rather than after they are installed in possibly difficult to reach locations. This helps limit potential installation problems to primarily Ethernet and power areas. Figure E-1 illustrates a typical priming configuration for your access points.
Appendix E Priming Access Points Prior to Deployment Before deploying your access points to their final locations, follow these steps to prime your access points: Step 1 In a Layer 2 environment, where the access points are located on the same subnet as the controller, the access point communicates directly with the controller. Step 2 In a Layer 3 environment, ensure a DHCP server (typically on your switch) is enabled on the same subnet as your access points.
Appendix E Priming Access Points Prior to Deployment Step 6 If the operating system download is successful, the access point reboots. Normal operation is indicated when the Alarm LED is off, the Power LED is green, and the 2.4 GHz and 5 GHz LEDs are blinking to indicate radio activity. Note If the Alarm LED remains red for more than a minute, remove power from the access point and contact Cisco Technical Support for assistance.
Appendix E Priming Access Points Prior to Deployment Cisco Aironet 1000 Series Lightweight Access Point Hardware Installation Guide E-4 OL-9403-04
A P P E N D I X F Configuring DHCP Option 43 This appendix describes the steps needed to configure DHCP Option 43 on a Windows 2003 Enterprise DHCP server, such as a Cisco Catalyst 3750 series switch, for use with lightweight access points.
Appendix F Configuring DHCP Option 43 Overview Overview This section contains a DHCP Option 43 configuration example on a Windows 2003 Enterprise DHCP server for use with Cisco Aironet lightweight access points. For other DHCP server implementations, consult the DHCP server documentation for configuring DHCP Option 43. In Option 43, you should use the IP address of the controller management interface. Note DHCP Option 43 is limited to one access point type per DHCP pool.
Appendix F Configuring DHCP Option 43 Configuring Option 43 for 1000 Series Access Points Configuring Option 43 for 1000 Series Access Points To configure DHCP Option 43 for Cisco 1000 series lightweight access points in the embedded Cisco IOS DHCP server, follow these steps: Step 1 Enter configuration mode at the Cisco IOS command line interface (CLI). Step 2 Create the DHCP pool, including the necessary parameters such as default router and name server.
Appendix F Configuring DHCP Option 43 Configuring Option 43 for 1100, 1130, 1200, 1240, and 1300 Series Access Points Configuring Option 43 for 1100, 1130, 1200, 1240, and 1300 Series Access Points To configure DHCP Option 43 for Cisco Aironet 1100, 1130, 1200, 1240, and 1300 series lightweight access points in the embedded Cisco IOS DHCP server, follow these steps: Step 1 Enter configuration mode at the Cisco IOS CLI.
I N D EX DHCP pool A F-2 discovery process access point DHCP server discovery 1-1 DNS server guidlines 1-2 Layer 2 types 1-4 2-7 2-6 locally stored administrative rules, Taiwan B-9 antennas 2-6 Over-the-air wireless (OTW) dual radio external 2-7 2-6 1-4 1-5 integrated C-2 anti-theft feature E 1-6 EMI and susceptibility standards C-3 Ethernet C connector Canadian compliance ceiling-mount clips B-4 port 2-11 ceiling mounting process connectors controller F-2 F B-2
Index I O inline power 2-18 input power C-1 input voltage operating temperature C-1 installation guidelines C-1 P 2-3 package contents 2-3 power K cabling key features connector 1-2 keyhole slots 2-17 input 1-6 C-1 options 2-17 output L 2-18 C-2 sources 1-5 Layer 2 operation 1-8 power injector 2-17 Layer 3 operation 1-2, 1-7 power module 2-17 priming access points LED indicators location process, controller discovery 3-3, C-1 markings 2-19 R 3-4 lightweight
Index T temperature operating storage C-1 C-1 troubleshooting 3-1 type-length-value (TLV) F-2 U UL2043 1-6, C-2 unpacking 2-3 V Vendor Class Identifier (VCI) vendor class identifier (VCI) F-2 F-2 W warnings weight 2-2, A-1 C-1 Wireless Domain Services (WDS) 1-2 Cisco Aironet 1000 Series Lightweight Access Point Hardware Installation Guide OL-9403-04 IN-3
Index Cisco Aironet 1000 Series Lightweight Access Point Hardware Installation Guide IN-4 OL-9403-04
