User's Manual

78-20502-01 MX300 Floor Stand Installation Sheet | 2011 NOVEMBER | © 2011 Cisco Systems, Inc. All rights reserved.
Installing Cisco TelePresence MX300 - Floor Stand
2
Unpacking the MX300 box with the LCD video unit, Touch controller and accessories
i Cut the straps and lift off
the outer covering.
ii Remove the upper foam
protection.
Note: Leave the LCD
video unit in the bottom
tray for now.
iii Lift out the rectangular
box behind the LCD video
unit.
This box contains two
smaller boxes: One with
the Touch controller, and
one accessories box with
the microphones, cables,
screws and screwdriver.
Bottom tray
LCD video
unit
Touch controller
with cable
Accessories box:
• Two microphones
• Power cable
• Presentation cable
(VGA to DVI-I; stereo audio)
• Ethernet cable
• Four screws for fastening
the LCD video unit to the
floor stand
• Hexagonal screwdriver
• Two pairs of gloves
1
Unpacking the floor stand box and mounting the floor stand
i Unpack the floor stand box with the floor stand
base, floor stand column and floor stand covers,
screws and Allen key.
ii Place the floor stand base on the floor with the
cable channel facing upward and backward.
iii Raise the floor stand column with the cable
channel facing backward. Place the column
on the base and make sure the holes for the
screws are aligned.
iv Fasten the column to the base using the four
screws (tool: Allen key).
The two floor stand covers
will be mounted in step 6.
Floor Stand Base Screw (M6 x 16 Black) Main Unit Screw (M6 x 20 Black)
Floor Stand Base Screw (M6 x 16 Black) Main Unit Screw (M6 x 20 Black)
Floor Stand Base Screw (M6 x 16 Black) Main Unit Screw (M6 x 20 Black)
Floor Stand Base Screw (M6 x 16 Black) Main Unit Screw (M6 x 20 Black)
Floor stand
base
Floor stand
column
3
Mounting the LCD video unit to the floor stand
Cable channel lid
(for strain relief)
Floor stand
LCD video
unit
Note: Always use the provided gloves when handling
the LCD video unit to avoid stains on the unit’s surface.
i Lift the LCD video unit from the
bottom tray and slide it onto the
top of the floor stand column.
Two people working together are
required for this operation.
ii Remove the cable channel lid (see illustration) to
get access to the holes for the screws.
iii Fasten the LCD video unit to the column using the
four screws (tool: hexagonal screwdriver).
The MX300 delivery
The MX300 with a floor stand is delivered in three boxes
with the following parts:
• Floor stand column, floor stand base and floor stand
covers. Screws and Allen key
• LCD video unit, touch controller, microphones and
cables. Screws, screwdriver and gloves
• Back cover
Manpower
Two people working together are required to mount the
LCD video unit to the floor stand column.
Dimensions
Height (without camera): 1420 mm / 56 in.
Width: 1290 mm / 51 in.
Depth: 730 mm / 29 in.
Weight: 42 kg / 93 lb
Documentation
The user documentation for this product, including
compliance and safety information, is available on the Cisco
web site, http://www.cisco.com/go/telepresence/docs.
Outer
covering
31 kg / 68 lb
Floor Stand Base Screw (M6 x 16 Black) Main Unit Screw (M6 x 20 Black)
Floor Stand Base Screw (M6 x 16 Black) Main Unit Screw (M6 x 20 Black)
Floor Stand Base Screw (M6 x 16 Black)
Main Unit Screw (M6 x 20 Black)
Floor Stand Base Screw (M6 x 16 Black) Main Unit Screw (M6 x 20 Black)
Front