Laptop User Manual
Table Of Contents
- Cisco IOS XR Routing Configuration Guide
- Contents
- Preface
- Document Revision History
- Obtaining Documentation
- Documentation Feedback
- Cisco Product Security Overview
- Obtaining Technical Assistance
- Obtaining Additional Publications and Information
- Implementing BGP on Cisco IOS XR Software
- Contents
- Prerequisites for Implementing BGP on CiscoIOSXR Software
- Information About Implementing BGP on CiscoIOSXR Software
- BGP Functional Overview
- BGP Router Identifier
- BGP Default Limits
- BGP Validation of Local Next-Hop Addresses
- BGP Configuration
- No Default Address Family
- Routing Policy Enforcement
- Table Policy
- Update Groups
- BGP Best Path Algorithm
- Multiprotocol BGP
- Route Dampening
- BGP Routing Domain Confederation
- BGP Route Reflectors
- Default Address Family for show Commands
- How to Implement BGP on CiscoIOSXR Software
- Enabling BGP Routing
- Configuring a Routing Domain Confederation for BGP
- Resetting eBGP Session Immediately Upon Link Failure
- Logging Neighbor Changes
- Adjusting BGP Timers
- Changing the BGP Default Local Preference Value
- Configuring the MED Metric for BGP
- Configuring BGP Weights
- Tuning the BGP Best Path Calculation
- Indicating BGP Backdoor Routes
- Configuring Aggregate Addresses
- Redistributing iBGP Routes into IGP
- Redistributing Prefixes into Multiprotocol BGP
- Configuring BGP Route Dampening
- Applying Policy When Updating the Routing Table
- Setting BGP Administrative Distance
- Configuring a BGP Neighbor Group
- Configuring a BGP Neighbor
- Configuring a Route Reflector for BGP
- Configuring BGP Route Filtering by Route Policy
- Disabling Next Hop Processing on BGP Updates
- Configuring BGP Community and Extended-Community Filtering
- Configuring Software to Store Updates from a Neighbor
- Disabling a BGP Neighbor
- Resetting Neighbors Using BGP Dynamic Inbound Soft Reset
- Resetting Neighbors Using BGP Outbound Soft Reset
- Resetting Neighbors Using BGP Hard Reset
- Clearing Caches, Tables and Databases
- Displaying System and Network Statistics
- Monitoring BGP Update Groups
- Configuration Examples for Implementing BGP on CiscoIOSXR Software
- Where to Go Next
- Additional References
- Implementing IS-IS on Cisco IOS XR Software
- Contents
- Prerequisites for Implementing IS-IS on CiscoIOSXR Software
- Restrictions for Implementing IS-IS on CiscoIOSXR Software
- Information About Implementing IS-IS on CiscoIOSXR Software
- IS-IS Functional Overview
- Key Features Supported in the CiscoIOSXR IS-IS Implementation
- IS-IS Configuration Grouping
- IS-IS Interfaces
- Multitopology Configuration
- IPv6 Routing and Configuring IPv6 Addressing
- Limit LSP Flooding
- Maximum LSP Lifetime and Refresh Interval
- Overload Bit Configuration During Multitopology Operation
- Single-Topology IPv6 Support
- Multitopology IPv6 Support
- Nonstop Forwarding
- Multi-Instance IS-IS
- Multiprotocol Label Switching Traffic Engineering
- Overload Bit on Router
- Default Routes
- Attached Bit on an IS-IS Instance
- Multicast-Intact Feature
- How to Implement IS-IS on CiscoIOSXR Software
- Enabling IS-IS and Configuring Level 1 or Level 2 Routing
- Configuring Single Topology for IS-IS
- Configuring Multitopology for IS-IS
- Controlling LSP Flooding for IS-IS
- Configuring Nonstop Forwarding for IS-IS
- Configuring Authentication for IS-IS
- Configuring MPLS Traffic Engineering for IS-IS
- Tuning Adjacencies for IS-IS on Point-to-Point Interfaces
- Setting SPF Interval for a Single-Topology IPv4 and IPv6 Configuration
- Enabling Multicast-Intact for IS-IS
- Customizing Routes for IS-IS
- Configuration Examples for Implementing IS-IS on CiscoIOSXR Software
- Where to Go Next
- Additional References
- Implementing OSPF on Cisco IOS XR Software
- Contents
- Prerequisites for Implementing OSPF on CiscoIOSXR Software
- Information About Implementing OSPF on CiscoIOSXR Software
- OSPF Functional Overview
- Key Features Supported in the CiscoIOSXR OSPF Implementation
- Comparison of CiscoIOSXR OSPFv3 and OSPFv2
- Importing Addresses into OSPFv3
- OSPF Hierarchical CLI and CLI Inheritance
- OSPF Routing Components
- OSPF Process and Router ID
- Supported OSPF Network Types
- Route Authentication Methods for OSPF Version 2
- Neighbors and Adjacency for OSPF
- Designated Router (DR) for OSPF
- Default Route for OSPF
- Link-State Advertisement Types for OSPF Version 2
- Link-State Advertisement Types for OSPFv3
- Virtual Link and Transit Area for OSPF
- Route Redistribution for OSPF
- OSPF Shortest Path First Throttling
- Nonstop Forwarding for OSPF Version 2
- Load Balancing in OSPF Version 2 and OSPFv3
- Graceful Restart for OSPFv3
- Multicast-Intact Feature
- How to Implement OSPF on CiscoIOSXR Software
- Enabling OSPF
- Configuring Stub and Not-so-Stubby Area Types
- Configuring Neighbors for Nonbroadcast Networks
- Configuring Authentication at Different Hierarchical Levels for OSPF Version 2
- Controlling the Frequency that the Same LSA Is Originated or Accepted for OSPF
- Creating a Virtual Link with MD5 Authentication to Area 0 for OSPF
- Summarizing Subnetwork LSAs on an OSPF ABR
- Redistributing Routes from One IGP into OSPF
- Configuring OSPF Shortest Path First Throttling
- Configuring Nonstop Forwarding for OSPF Version 2
- Configuring OSPF Version 2 for MPLS Traffic Engineering
- Verifying OSPF Configuration and Operation
- Configuring OSPFv3 Graceful Restart
- Enabling Multicast-Intact for OSPFv2
- Configuration Examples for Implementing OSPF on CiscoIOSXR Software
- CiscoIOSXR for OSPF Version 2 Configuration: Example
- CLI Inheritance and Precedence for OSPF Version 2: Example
- MPLS TE for OSPF Version 2: Example
- ABR with Summarization for OSPFv3: Example
- ABR Stub Area for OSPFv3: Example
- ABR Totally Stub Area for OSPFv3: Example
- Route Redistribution for OSPFv3: Example
- Virtual Link Configured Through Area 1 for OSPFv3: Example
- Virtual Link Configured with MD5 Authentication for OSPF Version 2: Example
- Where to Go Next
- Additional References
- Implementing and Monitoring RIB on CiscoIOSXR Software
- Contents
- Prerequisites for Implementing RIB on CiscoIOSXR Software
- Information About RIB Configuration
- How to Deploy and Monitor RIB
- Configuration Examples for RIB Monitoring
- Output of show route Command: Example
- Output of show route backup Command: Example
- Output of show route best-local Command: Example
- Output of show route connected Command: Example
- Output of show route local Command: Example
- Output of show route longer-prefixes Command: Example
- Output of show route next-hop Command: Example
- Where to Go Next
- Additional References
- Implementing Routing Policy on Cisco IOS XR Software
- Implementing Static Routes on Cisco IOS XR Software
- Index
Implementing IS-IS on Cisco IOS XR Software
How to Implement IS-IS on Cisco IOS XR Software
RC-121
Cisco IOS XR Routing Configuration Guide
Step 5
default-information originate [route-map
map-name
]
Example:
RP/0/RP0/CPU0:router(config-isis-af)#
default-information originate
(Optional) Injects a default IPv4 or IPv6 route into an IS-IS
routing domain.
• The route-map keyword and map-name argument
specify the conditions under which the IPv4 or IPv6
default route is advertised.
• If the route-map keyword is omitted, then the IPv4 or
IPv6 default route is unconditionally advertised at
Level 2.
Step 6
redistribute isis
instance
[level-1 | level-2 |
level-1-2] [metric
metric
] [metric-type
{internal | external}] [policy
policy-name
]
Example:
RP/0/RP0/CPU0:router(config-isis-af)#
redistribute isis 2 level-1
(Optional) Redistributes routes from one IS-IS instance into
another instance.
• In this example, an IS-IS instance redistributes IS-IS
instance 2 routes into its Level 1 area.
Step 7
summary-prefix [
address
/
prefix-length
] [level
{1 | 2}]
or
summary-prefix [
ipv6-prefix
/
prefix-length
]
[level {1 | 2}]
Example:
RP/0/RP0/CPU0:router(config-isis-af)#
summary-prefix 10.1.0.0/16 level 1
or
RP/0/RP0/CPU0:router(config-isis-af)#
summary-prefix 3003:xxxx::/24 level 1
(Optional) Allows a Level 1-2 router to summarize Level 1
IPv4 and IPv6 prefixes at Level 2, instead of advertising the
Level 1 prefixes directly when the router advertises the
summary.
• This example specifies an IPv4 address and mask.
or
• This example specifies an IPv6 prefix, and the
command must be in the form documented in RFC 2373
in which the address is specified in hexadecimal using
16-bit values between colons.
• Note that IPv6 prefixes must be configured only in the
IPv6 router address family configuration submode, and
IPv4 prefixes in the IPv4 router address family
configuration submode.
Step 8
maximum-paths
route-number
Example:
RP/0/RP0/CPU0:router(config-isis-af)#
maximum-paths 16
(Optional) Configures the maximum number of parallel
paths allowed in a routing table.
Step 9
distance
weight
[
address
/
prefix-length
[
route-list-name
]]
Example:
RP/0/RP0/CPU0:router(config-isis-af)# distance
90
(Optional) Defines the administrative distance assigned to
routes discovered by the IS-IS protocol.
• A different administrative distance may be applied for
IPv4 and IPv6.
Command or Action Purpose