Cisco 800 Series Integrated Services Router Hardware Installation Guide Cisco Systems, Inc. www.cisco.com Cisco has more than 200 offices worldwide. Addresses, phone numbers, and fax numbers are listed on the Cisco website at www.cisco.com/go/offices.
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
Contents Preface vii Objective vii Audience vii Organization viii Conventions viii Related Documentation xvi Searching Cisco Documents xvi Obtaining Documentation and Submitting a Service Request Product Overview xvi 1-1 Cisco 810 Series 1-1 Cisco 812 Series 1-1 General Description 1-1 Hardware Features 1-4 SKU Information 1-9 Cisco 819 Series 1-10 General Description 1-10 SKU Information 1-14 Hardware Features 1-19 Cisco 860, 880, 890 Series 1-34 General Description 1-35 Cisco 860 Series
Contents Cisco C886VA Router 1-59 Cisco C886VAJ Router 1-60 Cisco C887VA Router 1-61 Cisco C887VAM Router 1-62 Cisco 890 Series ISRs 1-63 Cisco 891, Cisco 892, and Cisco 892F 1-63 Cisco C891 Series ISRs 1-73 Cisco C891F Router 1-74 Cisco C891FW Router 1-75 Hardware Features 1-77 Kensington Lock 1-78 Reset Button 1-78 LEDs 1-80 Memory 1-87 USB Port 1-88 Fan 1-89 Power Supply 1-89 Power over Ethernet Module 1-89 3G Cellular Data WAN Connectivity 1-90 Small Form-Factor Pluggable Port 1-92 Feature Summary 1-
Contents Installing on a Table 2-38 Mounting on a Wall 2-38 Installing the Router Ground Connection 2-41 Installing the FIPS Cover 2-41 Installing Antennas for Cisco 890 Series 2-45 Installing Cisco 890 Series in a Rack 2-49 Installing the C881G-B/S/V-K9 ISR 2-51 Installing Antennas 2-51 Installing the C881GW-S/V-A-K9 ISR 2-51 Installing Antennas 2-51 Installing the C881G-U-K9 ISR 2-51 Installing the Cisco 880G for 3.7G (HSPA+)/3.
Contents Connecting an xDSL Line 3-31 Connecting Power over Ethernet 3-34 Connecting the AC Adapter 3-35 Connecting an FXS Line 3-39 Connecting an FXO Line 3-40 Connecting a Voice ISDN BRI Line 3-42 Verifying Connections 3-45 Initial Configuration 4-1 Cisco 810 Series 4-1 Cisco 819 Series 4-1 Cisco IOS CLI 4-1 Setup Command Facility 4-1 Verifying the Initial Configuration 4-2 Cisco 860, 880, 890 Series 4-2 Cisco Configuration Professional Express 4-2 Cisco IOS CLI 4-2 Setup Command Facility 4-4 Verifyi
Contents Power Supply A-22 Wireless Access Point A-22 FE and GE Port Pinouts A-23 Console and Auxiliary Port Connector Pinouts A-24 FXS and FXO Port Connector Pinouts A-24 VDSL2 Port Connector Pinouts A-24 ADSL2+ Port Connector Pinouts A-25 V.92 Port Connector Pinouts A-25 G.
Contents Cisco 800 Series Integrated Services Router Hardware Installation Guide 6 OL-27407-01
Preface This preface describes the objectives, audience, organization, and conventions of this guide and describes related documents that have additional information.
Organization This guide is organized into the following chapters and appendix. Chapter Name Description Chapter 1 Chapter 1, “Product Overview” Describes the router models and the hardware features available. Chapter 2 Chapter 2, “Installing the Router” Lists the items shipped with the router, the equipment and tools necessary for installing the router, the safety warnings and guidelines, and the procedures for installing the router.
Warning IMPORTANT SAFETY INSTRUCTIONS This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device.
Avvertenza IMPORTANTI ISTRUZIONI SULLA SICUREZZA Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti. Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le traduzioni delle avvertenze riportate in questo documento.
Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 xi
Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo.
Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 xiii
Warning When installing the product, please use the provided or designated connection cables/power cables/AC adaptors. Using any other cables/adaptors could cause a malfunction or a fire. Electrical Appliance and Material Safety Law prohibits the use of UL-certified cables (that have the “UL” shown on the code) for any other electrical devices than products designated by CISCO.
Warning If the symbol of suitability with an overlaid cross appears above a port, you must not connect the port to a public network that follows the European Union standards. Connecting the port to this type of public network can cause severe personal injury or can damage the unit. Statement 1031 Warning Connect the unit only to DC power source that complies with the safety extra-low voltage (SELV) requirements in IEC 60950 based safety standards.
Warning Read the installation instructions before connecting the system to the power source. Statement 1004 Warning Ultimate disposal of this product should be handled according to all national laws and regulations. Statement 1040 Warning The covers are an integral part of the safety design of the product. Do not operate the unit without the covers installed. Statement 1077 Warning Hot surface.
Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS Version 2.0.
Cisco Integrated Services Router Hardware Installation Guide xviii OL-27407-01
CH A P T E R 1 Product Overview This chapter provides an overview of the features available for the Cisco 812, Cisco 819, Cisco 860, 880, 890 Integrated Services Router (ISR) and contains the following sections: Note • Cisco 810 Series, page 1-1 • Cisco 860, 880, 890 Series, page 1-33 For compliance and safety information, see Regulatory Compliance and Safety Information for Cisco 800 Series Routers.
Chapter 1 Product Overview Cisco 810 Series The 3rd Generation (3G) is a generation of standards for mobile technology that facilitates growth, increased in bandwidth, and supports more diverse applications. The Cisco 812 ISR can be powered by an (included) external AC adapter or by a PoE+ capable Ethernet source using an optional Cisco PoE splitter C810-POE-SPL.
Chapter 1 Product Overview Cisco 810 Series Figure 1-2 shows the 3G antenna and LEDs display.
Chapter 1 Product Overview Cisco 810 Series Figure 1-3 shows the I/O side of the Cisco 812 ISR. Figure 1-3 Cisco 812 ISR I/O Side 1 2 S 3 4 GE WAN L DIV/GPS MAIN C812G 5VDC 1 GE WAN port 3 Power connection port 2 Console/Aux port 4 Power switch 4.
Chapter 1 Product Overview Cisco 810 Series • Ceiling and Wall Mounting Option • LED indicators for the platform Antenna The Cisco 812 ISR supports 3G external antenna and WiFi embedded antenna. 3G External Antenna The Cisco 812 ISR provides two standard panel-mount TNC connectors to support 3G. The main antenna is used for the primary 3G antenna. The second can be used as a diversity receive only 3G antenna or an amplified GPS antenna. See Figure 1-2 for the location of the antennas.
Chapter 1 Product Overview Cisco 810 Series Table 1-1 Cisco 812 3G LED Descriptions (continued) ROMMON Mode 3G LED RSSI 1 LED Color Description White, Green, Light Blue, or Blue (solid) Signal > –60 dBm White, Green, Light Blue, or Blue (three blinks and then a long pause) Signal <= –60 to 74 dBm Very strong signal Strong signal. White, Green, Light Blue, or Signal <= –75 to –89 dBm Blue (two blinks and then a long Fair signal.
Chapter 1 Product Overview Cisco 810 Series Table 1-2 describes the WiFi LED for the Cisco 812 ISR. Table 1-2 Cisco 812 ISR WiFi LED Descriptions Message Type Color Description Boot loader status sequence Blinking Green DRAM memory test in progress. DRAM memory test is OK. Board initialization in progress. Initializing FLASH file system. Initializing Ethernet. Ethernet is OK. Starting Cisco IOS. Initialization successful.
Chapter 1 Product Overview Cisco 810 Series Table 1-2 Cisco 812 ISR WiFi LED Descriptions (continued) Message Type Color Description Cisco IOS errors Red Software failure. Try to disconnect and reconnect the unit power. Cycling through Blue, Green, Red, and Off General warning. Memory The Cisco 812 ISR supports 512 MB DRAM and 512 MB compact flash memory. The Host router software runs on the first core. The second core runs the WLAN Access Point software.
Chapter 1 Product Overview Cisco 810 Series Figure 1-4 PoE+ Splitter I/O Side OUTPUT 1 2 3 4 5 6 345067 OUTPUT 5 1 Grounding location 4 PoE+ input 2 Power status LED 5 Openings for power cord latch to lock into enclosure 3 GE0 output 6 Input power connection SKU Information Table 1-3 lists the different SKUs available for the Cisco 812 ISR. The AP802-AGN-X-K9 (WLAN PID) is integrated as part of the router for the SKUs that support WLAN and is not orderable separately.
Chapter 1 Product Overview Cisco 810 Series Cisco 819 Series This section provides an overview of the features available for the Cisco 819 and Cisco 819H Integrated Services Routers (ISRs) and contains the following sections: Note • General Description, page 1-10 • SKU Information, page 1-14 • Hardware Features, page 1-19 For compliance and safety information, see Regulatory Compliance and Safety Information Roadmap that ships with the router and Regulatory Compliance and Safety Information for C
Chapter 1 Product Overview Cisco 810 Series than replacing a wired LAN within a building or campus. WLANs use radio frequency to transmit and receive data over the air, minimizing the need for wired connections. Figure 1-6 shows the Cisco 819HGW ISR. The WLAN for 3G Cisco 819HGW and Cisco 819HWD ISRs have the following additional features: Note • Dual 802.
Chapter 1 Product Overview Cisco 810 Series Cisco 819HGW Integrated Services Router 285479 Figure 1-6 Figure 1-7 shows the front panel details of the Cisco 819HG ISR.
Chapter 1 Product Overview Cisco 810 Series 4 3G mini-USB diagnostic port 10 5 VDC molex power input 5 Diversity/GPS antenna 11 Power switch 6 12-in-1 serial port 12 Ground Figure 1-8 shows the front panel details of the Cisco 819HGW ISR.
Chapter 1 Product Overview Cisco 810 Series Figure 1-9 shows the front panel details of the Cisco 819 4G LTE ISR.
Chapter 1 Product Overview Cisco 810 Series Table 1-4 Supported 3G SKUs for Cisco 819HG and Cisco 819G ISRs (continued) SKU ID Description C819HG-B-K9 Compact Hardened 3G IOS Router with Bharat generic EVDO Rev A based on MC5728V C819G+7-K9 Compact Non-hardened 3G IOS Router with Global HSPA + Release 7 based on MC8705 C819G-U-K9 Compact Non-hardened 3G IOS Router with GLOBAL HSPA Release 6 based on MC8795V C819G-V-K9 Compact Non-hardened 3G IOS Router with Verizon EVDO Rev A based on MC5728V
Chapter 1 Product Overview Cisco 810 Series Table 1-5 lists the different SKUs available for the Cisco 819HGW, Cisco 819H, and Cisco 819HWD ISRs. Table 1-5 Supported SKUs for Cisco 819HGW, Cisco 819H, and Cisco 819HWD ISRs SKU ID WLAN ID WiFi External Antenna Support C819HGW+7-E-K9 AP802H-AGN-E-K9 Yes Cisco 819 Secure Hardened M2M GW (non-US) 3.7G HSPA + Release 7 with SMS/GPS and Dual WiFi Radio with ETSI C819HGW+7-N-K9 AP802H-AGN-N-K9 Yes Cisco 819 Secure Hardened M2M GW (non-US) 3.
Chapter 1 Product Overview Cisco 810 Series Table 1-6 lists the different 4G LTE SKUs available for the Cisco 819HG and Cisco 819G ISRs. Table 1-6 Supported 4G LTE SKUs for the Cisco 819HG-4G and Cisco 819G-4G ISRs SKU ID Mode Operating Regions Frequency Band Description C819HG-4G-V-K9 LTE—DOrA North America Compact Hardened Cisco 819 router with multimode LTE feature dedicated to Verizon Wireless networks. This comes with a Sierra Wireless MC7750 modem.
Chapter 1 Product Overview Cisco 810 Series Table 1-6 Supported 4G LTE SKUs for the Cisco 819HG-4G and Cisco 819G-4G ISRs (continued) SKU ID Mode Operating Regions Frequency Band Description C819HG-4G-G-K9 LTE—HSPA+/ Global Hardened Cisco 819 router with multimode LTE feature for global wireless networks. This comes with a Sierra Wireless MC7710 modem.
Chapter 1 Product Overview Cisco 810 Series Hardware Features This section provides an overview of the following hardware features for the Cisco 819 ISR.
Chapter 1 Product Overview Cisco 810 Series Table 1-7 Cisco 819 ISRs Platform Features (continued) Cisco 819HG Cisco 819G Cisco 819HGW Cisco 819HWD Cisco 819HG-4G Cisco 819G-4G (with 3G) (with WiFi) (with 4G LTE) 1 GB Compact Flash — support in IDE mode (internal) Yes Yes Cisco EnergyWise Yes Yes — Dual 802.
Chapter 1 Product Overview Cisco 810 Series Antennas The Cisco 819 3G routers provide two standard panel-mount TNC connectors to support the 3G antenna and the diversity and GPS external antenna. The main antenna is used for the primary 3G antenna. The second can be used as a diversity receive only 3G antenna or GPS antenna that does not require power supply from the router.
Chapter 1 Product Overview Cisco 810 Series Table 1-8 3G LED Descriptions (continued) LED Color Description ACT Green Network activity on FE Switch ports, GE WAN port, 3G cellular interface, and serial interfaces. Off No network activity. Green Module is powered on and connected but not transmitting or receiving. Green (slow blinking) Module is powered on and searching for connection. Green (fast blinking) Module is transmitting or receiving. Off Module is not powered.
Chapter 1 Product Overview Cisco 810 Series Table 1-8 3G LED Descriptions (continued) LED Color Description 3G Green (one blink and then a pause) For 1xRTT, EGPRS, or GPRS service. Green (two blinks and then a pause) For EVDO, EVDO/1xRTT, or UMTS. Green (three blinks and then a pause) For EVDO/1xRTT RevA, HSPA, or HSUPA/HSDPA. Green (solid) For HSPA PLUS. Off No Service. 1. Not applicable to Verizon and Sprint EVDO modems. 2. There is only one LED to indicate the status of two SIMs.
Chapter 1 Product Overview Cisco 810 Series Table 1-9 WLAN LED Descriptions (continued) WLAN LED Color Description Boot loader errors Blinking Red and Blue FLASH file system failure. Blinking Red and Off Environment variable failure. Bad MAC address. Ethernet failure during the image recovery. Boot environment failure. No Cisco image file. Boot failure. Cisco IOS errors Red Software failure. Try to disconnect and reconnect the unit power.
Chapter 1 Product Overview Cisco 810 Series Table 1-10 4G LTE LED Descriptions (continued) LED Color Description RSSI Green (solid) Signal > –60 dBm Very strong signal Green (three blinks and then a long pause) Signal <= –60 to 74 dBm Green (two blinks and then a long pause) Signal <= –75 to –89 dBm Green (one blink and then a long pause) Signal <= –90 to –109 dBm Off Signal <= –110 dBm Strong signal Fair signal Marginal signal Unusable signal SIM Green / Yellow (one SIM in slot 0 is act
Chapter 1 Product Overview Cisco 810 Series Table 1-11 Memory Requirements for Cisco 819 ISRs Cisco 819HG Cisco 819G Cisco 819HGW Cisco 819HWD Cisco 819HG-4G Cisco 819G-4G Memory Requirements (with 3G) (with WiFi) (with 4G LTE) 256 Compact Flash support in IDE mode (internal) Yes — — 1 GB Compact Flash support in IDE mode (internal) — Yes Yes 512 MB DRAM Yes — — 1 GB DRAM — Yes Yes Embedded 3G Modem The 3G cellular interface is the primary WAN data link, but it can also be used a
Chapter 1 Product Overview Cisco 810 Series Supported Cisco Antennas and Cables The Cisco 819 ISR provides two standard panel-mount TNC connectors to support the 3G antenna and the diversity and GPS external antenna. The main antenna is used for the primary 3G antenna. The second can be used as a diversity receive only 3G antenna or GPS antenna that does not require power supply from the router. Table 1-13 lists the Cisco 3G antennas that are supported for use on Cisco 819 ISRs.
Chapter 1 Product Overview Cisco 810 Series Table 1-14 lists the supported Cisco WiFi antenna for Cisco 819HGW and Cisco 819HWD ISRs. Table 1-14 Supported Cisco WiFi Antenna Antenna Frequency band(s) Mounting Mechanical AIR-ANTM2050D-R 2.4–2.5 GHz Faceplate IP Rating Peak Gain Peak Gain 2.4 GHz (dBi) 5 GHz (dBi) Description IP 41 1.4 4.5 This is the default antenna. For more information, see Cisco Multiband Swivel-Mount Dipole Antenna (AIR-ANTM2050D-R). 4.9–5.9 GHz Dipole AIR-ANT2430V-R 2.
Chapter 1 Product Overview Cisco 810 Series Table 1-15 lists the Cisco 4G LTE antennas that are supported for use on Cisco 819 ISRs. Table 1-15 Supported 4G LTE Antennas Cisco Part Number Description 4G-LTE-ANTM-D Indoor 4G dipole omnidirectional antenna Maximum Gain and Frequency Ranges • 2 dBi – 698 to 806 MHz – 824 to 894 MHz Description Multiband dipole antenna. For more information, see Cisco 4G/3G Omnidirectional Dipole Antenna (4G-LTE-ANTM-D).
Chapter 1 Product Overview Cisco 810 Series Table 1-16 to Table 1-18 list the extension cables for use with 3G, WiFi, and 4G LTE antennas. The tables include the insertion loss information for the ultra-low-loss (ULL) LMR 400 extension cables. Table 1-16 Cisco Extension Cables for Use with 3G Antennas Cisco Product Number Cable Length Insertion Loss Frequency (MHz) 3G-CAB-ULL-20 20 ft (6 m) 1.50 dB max 2100 3G-CAB-ULL-50 50 ft (15 m) 3.50 dB max 2100 3G-CAB-LMR240-25 25 ft (7.5 m) 3.
Chapter 1 Product Overview Cisco 810 Series Table 1-18 Cisco Extension Cables for Use with 4G LTE Antennas (continued) Cisco Product Number Cable Length Maximum Insertion Loss Frequency (MHz) Color Plenum Rated?1 4G-CAB-LMR240-50 50 ft (15 m) 4.1 dB at 700 MHz 700 to 1000 MHz Black Yes 7.4 dB at 2.6 GHz 1700 to 2600 MHz 6.1 dB at 700 MHz 700 to 1000 MHz Black Yes 11.0 dB at 2.6 GHz 1700 to 2600 MHz 2.1 dB at 700 MHz 700 to 1000 MHz Black No 4.
Chapter 1 Product Overview Cisco 810 Series 12-in-1 Serial Port 344749 Figure 1-10 Power Supply All SKUs require a 5 VDC power source. Cisco 819HG and Cisco 819G ISRs have a self-locking Molex mini-fit connector. Cisco 819HGW and Cisco 819HWD ISRs use a 5.5 mm barrel-type connector with separate locking clip. An external AC power adapter is supported by default.
Chapter 1 Product Overview Cisco 860, 880, 890 Series The vehicle power adapters may be used for fixed or mobile installations. They do not provide electrical isolation; the input negative is connected to the output negative (chassis ground). Input cable is 350 millimeter long with stripped and tinned bare wire connections. The input positive connection is a white wire and the input negative is a black wire. Note The 24 VDC vehicle adapters will be available on Q1CY13.
Chapter 1 Product Overview Cisco 860, 880, 890 Series Note Some illustrations in this document show a wireless router. Both wireless and nonwireless models are available in the Cisco 860 series, Cisco 880 series, and Cisco 890 series ISRs. Port and feature locations are similar for both wireless and nonwireless routers. Note Throughout this document the term VDSL refers to support for VDSL2 (ITU G.993.2) and ADSL refers to support for ADSL, ADSL2, & ADSL2+ (ITU G.992.1, G.992.3, & G.992.5).
Chapter 1 Product Overview Cisco 860, 880, 890 Series Figure 1-7 shows the front panel details of the Cisco 860 wireless router. Front Panel of the Cisco 860 Series Wireless ISR 231969 Figure 1-11 1 1 LEDs Figure 1-12 shows the back panel details of the Cisco 861 wireless (861W) ISR. Nonwireless routers do not have antennas on the back panel. However, the feature locations are similar for all Cisco 860 series routers.
Chapter 1 Product Overview Cisco 860, 880, 890 Series Cisco 860VAE Series ISRs The Cisco 860VAE series ISRs are fixed-configuration data routers. This section describes the features of the products in this series. Interfaces Table 1-20 describes the interfaces of the Cisco 860VAE series routers.
Chapter 1 Product Overview Cisco 860, 880, 890 Series Figure 1-13 shows the front panel details of the Cisco 866VAE, Cisco 867VAE, Cisco 866VAE-K9, and Cisco 867VAE-K9 integrated services routers (ISRs). Figure 1-13 Front Panel of the Cisco 860VAE series ISR 246199 Cisco 860 Series 1 1 LEDs Figure 1-14 shows the back panel details of the Cisco 866VAE ISR. Figure 1-14 Back Panel of the Cisco 866VAE ISR Cisco 866VAE VDSL/ADSL WAN OVER ISDN GE0 1 2 LAN CONSOLE 12V 2.
Chapter 1 Product Overview Cisco 860, 880, 890 Series Figure 1-15 shows the back panel details of the Cisco 867VAE-K9. Figure 1-15 Back Panel of the Cisco 867VAE-K9 ISR Cisco 867VAE-K9 VDSL/ADSL WAN CONSOLE LAN 12V 2.
Chapter 1 Product Overview Cisco 860, 880, 890 Series Common Features The following key features are common to each of these router models: • Dual WAN interface (Gigabit Ethernet [GE] and dual-mode ADSL2+ /VDSL2) • 2.4 GHz wireless LAN (WLAN) interface • Five Layer 2 LAN switches: two Gigabit Ethernet and three Fast Ethernet • One USB 2.
Chapter 1 Product Overview Cisco 860, 880, 890 Series Note For the Cisco C867VAE-POE-W-A-K9, Power-over-Ethernet (PoE) is available using port FE0, with a 60-W power supply. USB Interface The USB 2.0 interface enables: • Transferring data using a USB flash token (USB memory stick) for system recovery and other tasks. • Cisco IOS software boot from USB. Use only the following Cisco USB 2.0 flash tokens: Note • MEMUSB-128FT (128 MB) • MEMUSB-256FT (256 MB) • MEMUSB-1024FT (1 GB) The USB 2.
Chapter 1 Product Overview Cisco 860, 880, 890 Series LED Indicators on Front Panel The front panel includes several LED indicators. Figure 1-17 shows the location of the LED indicators.
Chapter 1 Product Overview Cisco 860, 880, 890 Series Table 1-25 describes the LED indicators. Table 1-25 Front Panel LED Indicators LED LED Color LED Activity Description Left Side DSL ACT Green Flashing Off — DSL WAN activity. Faster flashing indicates heavier traffic. Device is powered off. or No DSL WAN activity. DSL LINK Green Off Solid DSL WAN mode is selected and DSL training is complete.
Chapter 1 Product Overview Cisco 860, 880, 890 Series • Integrated 4-port 10/100 Ethernet switch for connecting to the LAN • 10/100 FE, VDSLoPOTS, ADSL over POTS, ADSL over ISDN, DSL Multi-mode (VDSL/ADSLoPOTS, VDSL/ADSLoISDN Cisco VA models only), or G.SHDSL port for connecting to the WAN • Optional embedded Wi-Fi CERTIFIED™, 802.
Chapter 1 Product Overview Cisco 860, 880, 890 Series Front Panel of the Cisco 880 Series Wireless Data Router 231950 Figure 1-18 1 1 2 2 3 LEDs 3G express card slot—Supports third-party 3G card (Cisco 880G models only) 3 USB port 1 1. See the Cisco 880 Series Integrated Services Routers data sheet for supported vendors. Figure 1-19 shows the back panel details of the Cisco 886VA data router.
Chapter 1 Product Overview Cisco 860, 880, 890 Series Figure 1-20 shows the back panel details of the Cisco 887VA and 886VA-M data router. Back Panel of the Cisco 887VA and 887VA-M Router 254139 Figure 1-20 1 2 3 4 5 1 Primary WAN port—VDSL/ADSL over POTS1 5 Reset button 2 4-port 10/100 Ethernet switch2 6 Power connector 3 Serial port—console or auxiliary 7 Earth ground connection 4 PoE power connector—optional 8 Kensington security slot 6 7 8 1. 887VA-M has Annex M support. 2.
Chapter 1 Product Overview Cisco 860, 880, 890 Series 1 ISDN port—not available on 3G models 6 PoE power connector for optional PoE module1 2 Primary WAN port2—G.SHDSL, VDSLoPOTS, ADSLoPOTS, ADSLoISDN, or 10/100 FE 7 Reset button 3 Antenna—captive omnidirectional dipole WLAN antenna (wireless models only) 8 Power connector 4 4-port 10/100 Ethernet switch 9 Earth ground connection 5 Serial port—console or auxiliary 10 Kensington security slot 1.
Chapter 1 Product Overview Cisco 860, 880, 890 Series Figure 1-22 shows the front panel details of the Cisco 881 SRST and Cisco 888 SRST wireless voice router.
Chapter 1 Product Overview Cisco 860, 880, 890 Series Figure 1-23 shows the back panel details of the Cisco 881SRST-W voice router.
Chapter 1 Product Overview Cisco 860, 880, 890 Series Figure 1-24 shows the back panel details of the Cisco 888SRST-W voice router. Back Panel of the Cisco C888SRST-W Voice Router 241905 Figure 1-24 2 1 2 6 3 4 5 7 8 9 10 1 Primary WAN port1—G.
Chapter 1 Product Overview Cisco 860, 880, 890 Series Note Configuring the codec complexity setting to support secure calls uses DSP resources, but does not affect the maximum number of supported calls. Table 1-26 Maximum Number of Supported Calls Flexible Complexity Medium Complexity High Complexity C881-V 9 8 6 C887VA-V 8 8 6 C887VA-V-W 8 8 6 Figure 1-25 shows the front panel details of the Cisco 881-V, Cisco 887VA-V, and Cisco 887VA-V-W.
Chapter 1 Product Overview Cisco 860, 880, 890 Series Figure 1-26 shows the back panel for the Cisco 887VA-V-W router. The Cisco 887VA-V (non-wireless) router does not have the antennas on the back panel.
Chapter 1 Product Overview Cisco 860, 880, 890 Series 1 Fast Ethernet WAN port 6 PoE power connector (optional) 2 Voice BRI ports 7 Reset button 3 Voice ports—four FXS/DID ports and one FXO port. 8 Power connector 4 Fast Ethernet LAN—four ports 9 Earth ground connection 5 Console Port 10 Kensington security slot Cisco 880 Series with Embedded WLAN Antennas Some Cisco 880W, 880WD, and 880-WD ISRs have three embedded WLAN antennas.
Chapter 1 Product Overview Cisco 860, 880, 890 Series Figure 1-29 shows the back panel details of the C887VA-WD-A-K9 and C887VA-WD-E-K9 ISRs.
Chapter 1 Product Overview Cisco 860, 880, 890 Series Figure 1-31 shows the back panel details of the C881WD-A-K9 and C881WD-E-K9 ISRs.
Chapter 1 Product Overview Cisco 860, 880, 890 Series C881G-U-K9 ISRs The C881G-U-K9 ISR is a member of the Cisco 880 series data routers. These routers provide integrated Virtual Private Network (VPN), embedded Wi-Fi CERTIFIED™, 802.11b/g/n-compliant wireless Access Point (AP), 3G, and backup capabilities. For information on configuring Cisco 880 Series ISRs, see Cisco 880 Series Integrated Services Router Software Configuration Guide.
Chapter 1 Product Overview Cisco C881, C886, and C887 Series ISRs Cisco C881, C886, and C887 Series ISRs Cisco C881, C886, and C887 Series ISRs offer broadband speed and simplified management to small businesses, small enterprise branches, and teleworkers. The Cisco C881, C886, and C887 Series ISR models have a lead-free, fanless chassis and are updated versions of the previous Cisco 881, 886, and 887 series (excluding 3G and wireless models).
Chapter 1 Product Overview Cisco C881, C886, and C887 Series ISRs Figure 1-32 Front Panel of the Cisco C881 Router OK PPP 0 1 FE4 FE WAN POE OE 0 1 2 3 361124 Cisco 800 Series FE LAN VPN 1 1 LEDs For detailed description about the LEDs on the Cisco C880 Series Routers, see the “LEDs” section on page 1-21.
Chapter 1 Product Overview Cisco C881, C886, and C887 Series ISRs Figure 1-33 shows the back panel of the Cisco C881 Router. Figure 1-33 Back Panel of the Cisco C881 Router Cisco 881 CONSOLE FE LAN FE WAN 361125 (POE) RESET 0 4 1 3 2 2 1 0 AUX 3 4 12VDC 5 2.
Chapter 1 Product Overview Cisco C881, C886, and C887 Series ISRs Figure 1-35 shows the back panel of the Cisco C886VA Router. Figure 1-35 Back Panel of the Cisco C886VA Router VDSL/ADSL CONSOLE FE LAN ISDN 361127 (POE) RESET 0 over ISDN 1 2 0 3 2 3 1 0 4 AUX 5 12VDC 6 2. -5A 2.
Chapter 1 Product Overview Cisco C881, C886, and C887 Series ISRs Figure 1-37 shows the back panel of the Cisco C886VAJ Router. Figure 1-37 Back Panel of the Cisco C886VAJ Router VDSL/ADSL CONSOLE FE LAN ISDN 361129 (POE) RESET 0 over ISDN 1 2 0 3 2 3 1 4 0 AUX 12VDC 5 6 2. -5A 2.
Chapter 1 Product Overview Cisco C881, C886, and C887 Series ISRs Figure 1-39 shows the back panel of the Cisco C887VA Router. Figure 1-39 Back Panel of the Cisco C887VA Router Cisco 887 887VA VDSL/ADSL CONSOLE FE LAN 361131 (POE) RESET 0 over POTS 1 3 2 2 1 0 3 AUX 4 12VDC 5 2.5-5A 2.
Chapter 1 Product Overview Cisco C881, C886, and C887 Series ISRs Figure 1-41 shows the back panel of the Cisco C887VAM router. Figure 1-41 Back Panel of the Cisco C887VAM Router Cisco 887 887VAM AM VDSL/ADSL CONSOLE FE LAN 361133 (POE) RESET 0 over POTS 1 3 2 2 1 0 AUX 3 4 12VDC 5 2.5-5A 2.
Chapter 1 Product Overview Cisco C881, C886, and C887 Series ISRs • DIMM expansion socket that can accept up to 512 MB of additional memory, for a total of 768 MB system memory in Cisco 891 and 892 series ISRs, and a total of 1 GB system memory in Cisco 892F series ISRs • Three reverse-polarity threaded Neill-Concelman (RP-TNC) connectors on the back panel for non-captive dual-band WLAN antenna (wireless models only) • Support for the AIM2-CUE-K9 and AIM2-APPRE-104-K9 • GE small-form-factor pluggab
Chapter 1 Product Overview Cisco C881, C886, and C887 Series ISRs Figure 1-43 shows the back panel details of the Cisco 892-W router. Nonwireless routers do not have RP-TNC antennas or connectors on the back panel. Some of the features that are shown may not be available on your router. However, the feature locations are similar across all Cisco 890 series routers.
Chapter 1 Product Overview Cisco C881, C886, and C887 Series ISRs Figure 1-44 shows the location of the SFP port in a Cisco 892F-W router.
Chapter 1 Product Overview Cisco C881, C886, and C887 Series ISRs Figure 1-45 shows the back panel of the Cisco 892FSP router. Figure 1-45 Back Panel of the Cisco 892FSP Router Cisco 892FSP CONSOLE GE WAN GE WAN 284781 SFP RESET 8 9 AUX 8 12VDC 1 2 3 4 5 2.
Chapter 1 Product Overview Cisco C881, C886, and C887 Series ISRs Figure 1-47 shows the back panel of the Cisco 896VA router. Figure 1-47 Back Panel of the Cisco 896VA Router 12 VDSL/ADSL overISDN GE WAN 0 8 1 2 6 GELAN 5 Cisco 896VA 4 CONSOLE 3 3 4 2 POE 5 1 54VDC 12VDC 0 6 1 ISDN 7 Power connector 2 GE WAN interface 8 On/Off switch 3 SFP port 9 Reset button 4 USB port 7 344766 ISDN 7 RESET 1.2A 2.
Chapter 1 Product Overview Cisco C881, C886, and C887 Series ISRs Figure 1-49 shows the back panel of the Cisco 897VA router. Figure 1-49 Back Panel of the Cisco 897VA Router 12 VDSL/ADSL overPOTS GE WAN 0 8 1 2 7 6 GELAN 5 Cisco 897VA 4 CONSOLE 3 3 2 4 POE 1 54VDC 12VDC 0 6 5 1 ISDN 7 Power connector 2 GE WAN interface 8 On/Off switch 3 SFP port 9 Reset button 4 USB port RESET 1.2A 2.
Chapter 1 Product Overview Cisco C881, C886, and C887 Series ISRs 4 8-port Gigabit Ethernet switch1 10 Kensington security slot 5 Console / Auxiliary port 11 VDSL / ADSL over POTS 6 Power connector 1. Port 0 through 3 can be configured as POE. POE is an optional feature for this model. If this feature was not configured with the factory order, you must order and install it to enable the PoE function. Figure 1-51 shows the front panel of the Cisco 897VAM router.
Chapter 1 Product Overview Cisco C881, C886, and C887 Series ISRs Figure 1-53 shows the front panel of the Cisco 897VAW and the Cisco 897VAMW router. Front Panel of the Cisco 897VAW and the Cisco 897VAMW Router 344770 Figure 1-53 1 1 LEDs Figure 1-54 shows the back panel of the Cisco 897VAMW router. Figure 1-54 Back Panel of the Cisco 897VAMW Router 11 VDSL/ADSL overPOTS 7 6 GELAN 5 4 8 1 3 2 3 2 POE 4 1 54VDC 12VDC 0 5 6 RESET 1.2A 2.
Chapter 1 Product Overview Cisco C881, C886, and C887 Series ISRs Figure 1-55 shows the back panel of the Cisco 898EA router. Figure 1-55 Back Panel of the Cisco 898EA Router 7 SHDSL RJ45 ONLY 11 6 GELAN 5 Cisco 898EA 4 CONSOLE GE WAN 8 8 1 2 3 3 2 POE 1 4 AUX 0 5 54VDC 12VDC 6 RESET 1.2A 2.
Chapter 1 Product Overview Cisco C891 Series ISRs Cisco C891 Series ISRs Cisco C891 Series ISRs are designed to deliver secure broadband, metro Ethernet, wireless LAN (WLAN) connectivity, and business continuity. Cisco C891 Series ISRs also provide a 1-port Gigabit Ethernet SFP socket for WAN connectivity. This section includes the hardware information for the following models: • Cisco C891F • Cisco C891FW Table 1-28 provides information about the hardware specifications of Cisco C891 Series Router.
Chapter 1 Product Overview Cisco C891 Series ISRs Cisco C891F Router Figure 1-57 shows the front panel of the Cisco C891F Router: Front Panel of the Cisco C891F Router OK OK 0 POE OE 1 2 3 4 POE OE ISDN VPN PPP V.92 5 6 7 GE8 SFP8 FE0 WAN GE LAN B1 B2 Cisco 800 Series 361136 Figure 1-57 1 1 LEDs For detailed description about the LEDs on the Cisco C890 Series Routers, see the “LEDs” section on page 1-21.
Chapter 1 Product Overview Cisco C891 Series ISRs Figure 1-58 shows the back panel of the Cisco C891F Router. Figure 1-58 Back Panel of the Cisco C891F Router 7 FE WAN AN ISDN GE WAN AN 6 GE LAN AN 5 Cisco 891F Ci 89 4 CON ONSOLE OLE V.92 .92 (POE) 361137 SFP RESET RES 0 0 8 8 1 2 3 4 0 5 3 6 2 POE 1 0 7 UX AUX 8 54VDC 54V 12V 12VDC 1.5A .5A 3.
Chapter 1 Product Overview Cisco C891 Series ISRs For detailed description about the LEDs on Cisco C890 Series Router, see “LEDs” section on page 1-21.
Chapter 1 Product Overview Cisco C891 Series ISRs Figure 1-60 shows the back panel of the Cisco C891FW Router. Figure 1-60 Back Panel of the Cisco C891FW Router 7 FE WAN AN ISDN GE WAN AN 6 GE LAN AN 5 Cisco 89 Ci 891FW FW 4 CON ONSOLE OLE V.92 .92 (POE) 361139 SFP RESET RES 0 0 8 8 1 2 3 4 0 5 3 6 2 POE 1 0 7 AUX UX 8 54VDC 54V 12V 12VDC 1.5A .5A 3.
Chapter 1 Product Overview Cisco C891 Series ISRs • Feature Summary Kensington Lock A Kensington security slot is located on the router back panel. To secure the router to a desktop or other surface, use the Kensington lockdown equipment. Reset Button The Reset button is used to restore the router to the factory default configurationor to load a custom configuration file. There are two different ways to do this: Note 1. by pressing the Reset button within 5 seconds of powering up the router; or 2.
Chapter 1 Product Overview Cisco C891 Series ISRs Step 2 Press and hold the Reset button until the system status LED begins to flash. Typically, this occurs within 5 seconds. The router reloads itself after the startup configuration has been replaced with the new customer configuration. Custom Configuration File for Cisco 892FSP, 896VA, 897VA, and Cisco 898EA For the first method, the configuration file can be located on the router's compact flash or on the router's nvram.
Chapter 1 Product Overview Cisco C891 Series ISRs To reset the router to the factory default configuration or to load a custom configuration file, follow these steps: Step 1 Turn the power on. Step 2 Press and hold the Reset button until the system status LED begins to flash. Typically, this occurs within 5 seconds. The router reloads itself after the startup configuration has been replaced with the new customer configuration.
Chapter 1 Product Overview Cisco C891 Series ISRs • Table 1-29 For a description of LEDs for Cisco 860VAE-W-A-K9, Cisco 860VAE-W-E-K9, and Cisco 860VAE-POE-W-A-K9 ISRs models, see the “Cisco 860VAE-W-A-K9, Cisco 860VAE-W-E-K9, and Cisco 860VAE-POE-W-A-K9 ISRs” section on page 1-38.
Chapter 1 Product Overview Cisco C891 Series ISRs Table 1-29 LED Descriptions for the Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs (continued) LED Color Description 860 Series 880 Series 890 Series WLAN (5 GHz) Green On—Radio is connected, SSID is configured, and client is — associated, but no data is being received or being transmitted.
Chapter 1 Product Overview Cisco C891 Series ISRs Table 1-29 LED Descriptions for the Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs (continued) LED Color Description 860 Series 880 Series 890 Series Data BRI B2 Green Blinking—B2 channel is receiving or sending data, or data is passing through ISDN channel 2. — 887, 887V, 892 888 models models 3G8 WWAN9 Green On—Service is established. — 3G models — — 3G models — Slow Blinking—Searching for service.
Chapter 1 Product Overview Cisco C891 Series ISRs 2. LWAPP = Lightweight Access Point Protocol. 3. PPP = Point-to-Point Protocol. 4. xDSL = General term referring to various forms of DSL, including ADSL (asymmetric digital subscriber line) and VDSL (very-high-data-rate digital subscriber line). 5. DSLAM = digital subscriber line access multiplexer. 6. ATM = Asynchronous Transfer Mode. 7. EFM = Ethernet in the First Mile. 8. 3G = Third-Generation. 9. WWAN = wireless WAN. 10.
Chapter 1 Product Overview Cisco C891 Series ISRs Table 1-30 LED Descriptions for the Cisco 866VAE, Cisco 867VAE, Cisco 866VAE-K9, and Cisco 867VAE-K9 ISRs LED Activity Description GE ACT Green On—GE WAN interface is up. Blinking—GE WAN activity (traffic in either direction). Off—Device is powered off or GE WAN interface is down. GE Mode Green On—GE WAN Mode is selected. Off—Device is powered off or DSL WAN mode is selected. 1.
Chapter 1 Product Overview Cisco C891 Series ISRs Table 1-31 describes the LEDs for the Cisco 892FSP. Table 1-31LED desciption for Cisco 892FSP ISR, 896VA, 897VA, and 898EA Routers LED Color Activity Description PWR_OK Green Power Status Off—No power. Steady on—Normal operation. Blink—Boot up phase or in ROM Monitor mode. GE0 Green/Amber Link Status GE1 Green On—Ethernet port is connected. Amber On—Fault with PoE. There is a fault with the inline power supply.
Chapter 1 Product Overview Cisco C891 Series ISRs Because the LED indicators are shared, the LED illuminates (green) when either port is active. For example, the LED indicator labeled BRI 1 B1 illuminates when either the BRI1 B1 channel is active or when the FXS port is active. You can determine the activity status on each interface by using the following commands. • For activity status on the FXS ports, use the show port summary command.
Chapter 1 Product Overview Cisco C891 Series ISRs Note Flash memory is not upgradable. An external USB flash memory module may be used if additional flash memory is needed. Main Memory Table 1-33 describes the main onboard memory storage for different router models. Table 1-33 Main Onboard Memory Storage Models Onboard Memory Storage Expandability Cisco 860 series routers 256 MB Not expandable. Cisco 860VAE series routers 256 MB Not expandable.
Chapter 1 Product Overview Cisco C891 Series ISRs Fan Some router models do not have a fan, while other models have either one or two fans. The fans spin at full speed, as a diagnostic aid, immediately after the router is powered up. After the router has booted, the fans spin as fast as necessary to minimize fan noise while maintaining a safe internal operating temperature.
Chapter 1 Product Overview Cisco C891 Series ISRs 3G Cellular Data WAN Connectivity The 3G (Evolution Data Only [EVDO], Universal Mobile Telecommunications Systems [UMTS]) cellular interface is intended for use as a backup data link, but it can also be used as a primary WAN data link. The 3G technology is third-generation wide-area cellular technology that is used in voice telephony and broadband wireless data in a mobile environment.
Chapter 1 Product Overview Cisco C891 Series ISRs Table 1-35 Wireless Device Radios and Antennas Maximum Data Radio Band Throughput1 Radio Module Platform Single-band 802.11b/g/n radio module Cisco 880 series routers with embedded WLAN antennas 100 Mb/s per radio, Autonomous and up to 200 Mb/s unified total Cisco 890 2.4 GHz and 5 GHz Antenna Three embedded, omnidirectional antennas: 2 dBi at 2.4 GHz Three embedded, dual-band, omnidirectional antennas: 2 dBi at 2.4 GHz and 5 dBi at 5 GHz 2.
Chapter 1 Product Overview Cisco C891 Series ISRs Small Form-Factor Pluggable Port The SFP port supports auto-media-detection, auto-failover, and remote fault indication (RFI), as described in the IEEE 802.3ah specification. See the Cisco 892F data sheet for a list of supported SFPs. Feature Summary Table 1-37 summarizes the hardware features available in the Cisco 860 series, Cisco 880 series, and Cisco 890 series ISRs.
Chapter 1 Product Overview Cisco C891 Series ISRs Table 1-37 Hardware Features Available in Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs (continued) Feature Description Embedded wireless AP 860 Series 880 Series 890 Series Provides Wi-Fi CERTIFIED™ 802.11a/b/g/n compliance. Wireless models The Cisco 860 series routers contain a single 802.11b/g/n radio. 802.11b/g/n Some Cisco 880 series routers contain a single 802.11b/g/n radio while others contain dual 802.11a/n and 802.
Chapter 1 Product Overview Cisco C891 Series ISRs Table 1-37 Hardware Features Available in Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs (continued) Feature Description 860 Series USB port, Supports USB 1.1. Provides connection for USB devices such as security tokens and flash memory. All models 866VAE, 867VAE, 866VAE-K9, 867VAE-K9 All models — Models with PoE Models with PoE The Cisco 880 series routers have a single USB port; the Cisco 890 series routers have two USB ports.
Chapter 1 Product Overview Cisco C891 Series ISRs Table 1-37 Hardware Features Available in Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs (continued) Feature Description BRI voice port The ISDN BRI S/T voice interface provides a client-side — (TE) ISDN S/T physical interface for connection to an NT1 device that terminates an ISDN telephone network. SFP21 port Supports auto-media-detection, auto-failover, and remote fault indication (RFI), as described in the IEEE 802.
CH A P T E R 2 Installing the Router This chapter describes the equipment and the procedures for successfully installing the Cisco 860, 880, 890 ISRs, Cisco 819 ISRs, and the Cisco 812 ISRs, and contains the following sections: • Installing the Cisco 810 ISR, page 2-1 • Installing the Cisco 860, 880, 890 ISR, page 2-38 Installing the Cisco 810 ISR This section contains the following: • Installing the Cisco 812 ISR, page 2-1 • Installing the Cisco 819 ISR, page 2-19 Installing the Cisco 812 ISR Thi
Chapter 2 Installing the Router Installing the Cisco 810 ISR Items Shipped with your Router Unpack the box and verify that all items listed on the invoice were shipped with the Cisco 812 ISR.
Chapter 2 Installing the Router Installing the Cisco 810 ISR Figure 2-1 10-24 Screws 1 1 2 285667 3 Step 2 1 10-24 screws 2 Box hanger 3 Shelf bracket (PID 700-39491-01) Install the PoE+ splitter into the mounting plate with four 6-32 screws. (See Figure 2-2.
Chapter 2 Installing the Router Installing the Cisco 810 ISR Figure 2-2 6-32 Screws 1 2 3 285668 4 1 6-32 screws 3 To PoE+ power source 2 Power cable with power cord lock installed 4 GE CAT5 cable Step 3 Connect the supplied plenum rated Cat5 cable to the GE0 port on the PoE+ splitter. Step 4 Connect the Cat5 cable from your PoE+ source to the PoE+ in port on the PoE+ splitter. Step 5 Place the power cord lock onto the power cord behind the connector overmold as shown in Figure 2-3.
Chapter 2 Installing the Router Installing the Cisco 810 ISR Step 6 Install the power cord with power cord lock to the power jack of the PoE+ splitter while making sure that the two arms of the power cord lock slide into the corresponding slots on the PoE+ splitter and are fully seated with both arms locking into the slots. Figure 2-4 shows the installation of the power cord lock and other cables.
Chapter 2 Installing the Router Installing the Cisco 810 ISR Figure 2-5 T-Rail 285669 To POE Power Source Installing the SIM Card This section describes how to install and replace the SIM card. Ensure that the router is not mounted to a wall, rack, or DIN rail. Caution Warning Do not touch any part of the exposed PCB circuit area when the SIM cover is removed. Hot surface.
Chapter 2 Installing the Router Installing the Cisco 810 ISR Accessing the SIM Card 344397 Figure 2-6 Step 4 Remove the SIM card and install the new cards. Step 5 Reinstall the same 6-32 flat head screws using a screw driver to secure the access panel back in place. Figure 2-7 shows the SIM card installed and the SIM access panel closed.
Chapter 2 Installing the Router Installing the Cisco 810 ISR SIM Access Panel 344398 Figure 2-7 Installing the 3G Antenna Note Warning Install the antenna before you mount the Cisco 812 ISR. Do not locate the antenna near overhead power lines or other electric light or power circuits, or where it can come into contact with such circuits. When installing the antenna, take extreme care not to come into contact with such circuits, because they may cause serious injury or death.
Chapter 2 Installing the Router Installing the Cisco 810 ISR Installing the 3G Antenna 344395 Figure 2-8 Step 2 Orient the antenna perpendicular with respect to the floor. Figure 2-9 shows the 3G antenna installed. 3G Antenna Installed 344396 Figure 2-9 Mounting the Cisco 812 ISR This section describes the steps in mounting the Cisco 812 ISR in several configurations, including on a suspended ceiling, on a hard ceiling or wall, and on an electrical or network box.
Chapter 2 Installing the Router Installing the Cisco 810 ISR • Mounting Bracket, page 2-10 • Ceiling Grip Clips, page 2-11 • Mounting the Cisco 812 ISR Below a Suspended Ceiling, page 2-13 • Mounting the Cisco 812 ISR on a Hard Ceiling or a Wall, page 2-15 • Mounting the Cisco 812 ISR to a Network or Electrical Box, page 2-17 • Grounding the Cisco 812 ISR, page 2-18 Mounting Hardware Mounting hardware for the Cisco 812 ISR consists of brackets, which connect to the bottom of the router, and c
Chapter 2 Installing the Router Installing the Cisco 810 ISR Figure 2-10 Universal Bracket Installed on the Cisco 812 ISR 285644 1 1 Universal bracket Ceiling Grip Clips Use a ceiling grid clip to mount the router on a suspended ceiling. The ceiling grid clip that you need depends on the ceiling tiles on your ceiling.
Chapter 2 Installing the Router Installing the Cisco 810 ISR Figure 2-11 shows a ceiling grid clip.
Chapter 2 Installing the Router Installing the Cisco 810 ISR T-Rail, Channel, and Beam Ceiling Rail Types Figure 2-13 Adapter Clips Installed with Ceiling Grid Clips 281531 Figure 2-12 281532 Adapter clips Access point Ceiling grid clip Mounting bracket Mounting the Cisco 812 ISR Below a Suspended Ceiling The recommended power option for the Cisco 812 ISR, when mounted below a suspended ceiling, is the Cisco C810-POE-SPL (PoE+ splitter) with the use of the supplied 1.
Chapter 2 Installing the Router Installing the Cisco 810 ISR Step 7 Hold the mounting bracket and insert a 6-32 x 0.18-inch screw into each of the four corresponding holes (A, B, or C) and tighten. Step 8 If necessary, drill or cut a cable access hole in the ceiling tile large enough for the Ethernet and power cables. Pull the cables through the access hole until you have about 1 foot of cable protruding from the hole. Step 9 (Optional).
Chapter 2 Installing the Router Installing the Cisco 810 ISR Suspended Ceiling Mounting Details 1 7 4 5 3 8 6 1 To PoE+ power source 5 GE CAT5 cable to PoE+ splitter 2 Ceiling T-rail 6 Power and GE cable routed through a ceiling mounting bracket and into the router so that the cabling is hidden from directly below 3 Ceiling tile with opening cut for 7 cables Ceiling grip clip 4 Power cable to PoE+ splitter Ceiling mount bracket 8 2 344533 Figure 2-14 Mounting the Cisco 812 ISR on
Chapter 2 Installing the Router Installing the Cisco 810 ISR Note Wall mounting is only supported with the I/O (antenna) side facing up. Step 1 Use the mounting bracket as a template to mark the locations of the mounting holes on the bracket. Figure 2-15 shows details of the mounting bracket. Caution Be sure to mark all four locations. To ensure a safe and secure installation, make sure you are using adequate fasteners and mount the router using no less than four fasteners.
Chapter 2 Installing the Router Installing the Cisco 810 ISR Step 3 (Optional) Drill or cut a cable access hole near and below the location of the mounting bracket cable access cover large enough for the Ethernet cable, building ground wire, and power cables. Step 4 Pull approximately 9 inches of cable through the hole. Step 5 Route the Ethernet and power cables through the bracket before you attach the bracket to the ceiling or wall.
Chapter 2 Installing the Router Installing the Cisco 810 ISR Step 4 Route the cables through the bracket before you attach the bracket to the ceiling. Step 5 Route the cables through the main cable access hole and then through the smaller access hole as shown in Figure 2-16. Step 6 (Optional) Use the ground screw to attach the building ground wire to the ground location on the base of the router. See the “Grounding the Cisco 812 ISR” section on page 2-18 for the general grounding instructions.
Chapter 2 Installing the Router Installing the Cisco 810 ISR Connecting the Ring Lug onto the Grounding Point 302791 Figure 2-17 1 Step 7 2 1 6-32 ground screw 2 Ground wire Connect the ring lug to the router grounding point and reinstall the same 6-32 screw.
Chapter 2 Installing the Router Installing the Cisco 810 ISR Warning This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024 Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Chapter 2 Installing the Router Installing the Cisco 810 ISR Items Shipped with your Router Unpack the box and verify that all items listed on the invoice were shipped with the Cisco 819 ISR.
Chapter 2 Installing the Router Installing the Cisco 810 ISR If you plan to configure the software using Cisco IOS commands through the console port, provide an ASCII terminal or a PC that is running terminal emulation software to connect to the console port. If you plan to connect a modem, provide the modem and modem cable. Installing the Router This section describes how to install the Cisco 819 ISR.
Chapter 2 Installing the Router Installing the Cisco 810 ISR Warning Do not cover or obstruct the router vents located on both sides of the router; otherwise, overheating could occur and cause damage to the router. Warning Do not place anything on top of the router that weighs more than 10 pounds (4.5 kilograms), and do not stack routers on a desktop. Excessive weight on top of the router could damage the chassis.
Chapter 2 Installing the Router Installing the Cisco 810 ISR Installing Antennas Note Before you install the Cisco 819 ISR on a table, wall, or DIN rail, install the antennas on the front panel. It is difficult to install the antennas after the router is installed. To attach the radio antennas to your wireless router, follow these steps: Step 1 Manually screw the antenna tight to the TNC connectors on the back of the router. (See Figure 2-19.
Chapter 2 Installing the Router Installing the Cisco 810 ISR Figure 2-20 Cisco WiFi Antenna Assembly 1 3 1 3G Dipole External Antenna 3 2 WiFi 2.4/5 Ghz Dipole External Antenna 344030 2 RP-TNC Connector Installing on a Table To install the router on a table or other flat horizontal surface, firmly place the router on a table or other horizontal surface. Keep at least 1 inch (2.5 centimeters) of clear space for heat dissipation. Connect the chassis to a reliable earth ground.
Chapter 2 Installing the Router Installing the Cisco 810 ISR To mount the router on a wall, follow these steps: Step 1 Remove the screws on the sides of the routers. Step 2 Attach the standard brackets to the chassis using the three screws provided for each bracket. (See Figure 2-21.) Attaching the Standard Brackets 282622 Figure 2-21 Step 3 Install the router to a wall stud using two number-10 wood screws, round- or pan-head, with number-10 washers or two number-10 washer-head screws.
Chapter 2 Installing the Router Installing the Cisco 810 ISR Installing the Router to the Wall 282623 Figure 2-22 Note Step 4 For hollow-wall mounting, each bracket requires two wall anchors with washers. Wall anchors and washers must be size number 10. Route the cables so that they do not put a strain on the connectors or mounting hardware. To comply with IP 41, cables should be routed down relative to the router to prevent water from travelling on the cables.
Chapter 2 Installing the Router Installing the Cisco 810 ISR To attach the Cisco 819 ISR to a 35-mm wide DIN rail, follow these steps. Step 1 Attach the DIN rail to the back of the router using the three screws provided. (See Figure 2-23.) Attaching the DIN Rail to the Cisco 819 ISR 282624 Figure 2-23 Step 2 Find the tab on the end of the DIN rail that extends past the router. (See Figure 2-24.) Press the tab in and slide the DIN rail out while the tab is pressed down.
Chapter 2 Installing the Router Installing the Cisco 810 ISR Cisco 819 ISR Installed with the DIN Rail 282626 Figure 2-25 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 2-29
Chapter 2 Installing the Router Installing the Cisco 810 ISR Installing the Router Using the Configurable Low Profile DIN Mount If space is limited between the DIN rail and the enclosure cover, the Configurable Low Profile DIN Mount can be utilized to mount the router flat against the DIN rail. It can also be configured in three different ways to allow router cabling to exit from the bottom, right or left.
Chapter 2 Installing the Router Installing the Cisco 810 ISR Configuring the Mount Figure 2-27 Low Profile DIN Mount Configuration 1 4 2 4 5 6 391199 3 1 Mount tray 4 DIN Rail Latch Springs 2 DIN Rail Latch Bracket Screws 5 DIN Rail Brackets 3 Mount Serial Number 6 DIN Rail Latch The mount comes configured in a bottom cable exit position, with the rail latches in the slots marked Bottom. To reconfigure the mount: 1. Remove the two DIN Rail Latch Bracket Screws (Item 2). 2.
Chapter 2 Installing the Router Installing the Cisco 810 ISR Attaching the mount to the router Cisco ISR 819 mounted in a Configurable Low Profile DIN mount 391253 Figure 2-28 To attach the router to the mount: 1. Remove the bottom screw of the 3 screws on the sides of the router at the front. 2. Slip the router into the mount tray 3. Align the holes at the front sides of the mount with the vacant screw holes on the router and screw the mount to the router with the longer, 6-32 x .
Chapter 2 Installing the Router Installing the Cisco 810 ISR Installing the Router Ground Connection The router must be connected to a reliable earth ground. Install the ground wire in accordance with local electrical safety standards. Warning • For NEC-compliant grounding, use size 14 AWG (2 mm2) or larger copper wire and a ring terminal with an inner diameter of 1/4 in. (5 to 7 mm). • For EN/IEC 60950-compliant grounding, use size 18 AWG (1 mm2) or larger copper wire.
Chapter 2 Installing the Router Installing the Cisco 810 ISR After you install and properly ground the router, you can connect the power wiring, the LAN cables, and the cables for administrative access as required for your installation. Installing the Power Cord Retention Lock The Cisco 819 ISRs have a power cord retention mechanism as an accessory. It locks the power cord to the router so when a user accidentally pulls out the power cord, the power cord will not come out from the router.
Chapter 2 Installing the Router Installing the Cisco 810 ISR Step 3 Install the power cord with power cord lock and the pre-installed o-ring to mate with the power jack on the router while making sure that the two arms of the power cord lock slide into the corresponding slots on the router and are fully seated with both arms locking into the slots as shown in Figure 2-32.
Chapter 2 Installing the Router Installing the Cisco 810 ISR Figure 2-34 Installing Power Switch Lock 1 2 3 4 344033 5 1 Ring terminal 4 Power switch lock 2 Power switch lock washer 5 Pan-head screw 3 Power switch lock standoff Power Switch Lock Installed 344034 Figure 2-35 Cisco Integrated Services Router Hardware Installation Guide 2-36 OL-27407-01
Chapter 2 Installing the Router Installing the Cisco 810 ISR Mounting the DC Power Supply Warning Read the wall-mounting instructions carefully before beginning installation. Failure to use the correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system. Statement 378 The Cisco 800 ISR DC power supply may be mounted to a wall using four #6 pan- or round-head wood screws for the mounting holes on the supply.
Chapter 2 Installing the Router Installing the Cisco 860, 880, 890 ISR Note The DC supply is IP 41 compliant in all six orthogonal directions. The mounting orientation will not affect IP 41 compliance.
Chapter 2 Installing the Router Installing the Cisco 860, 880, 890 ISR Equipment, Tools, and Connections This section describes the equipment, tools, and connections necessary for installing your Cisco 860 series, 880 series, and 890 series ISRs.
Chapter 2 Installing the Router Installing the Cisco 860, 880, 890 ISR – Two number-10 wall anchors with washers, for mounting the router on a hollow-wall. • Wire crimper for chassis grounding. • Wire for connecting the chassis to an earth ground: – AWG 14 (2 mm2) or larger wire for NEC-compliant chassis grounding. – AWG 18 (1 mm2) or larger wire for EN/IEC 60950–compliant chassis grounding. • Ring terminal with an inner diameter of 1/4 in. (5 to 7 mm), for NEC-compliant chassis grounding.
Chapter 2 Installing the Router Installing the Cisco 860, 880, 890 ISR Warning This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024 Warning Read the wall-mounting instructions carefully before beginning installation.
Chapter 2 Installing the Router Installing the Cisco 860, 880, 890 ISR The mounting holes are bidirectional. You can hang the router with the front bezel facing upward or downward. Keep at least 1 inch (2.5 cm) of clear space beside the cooling inlet and exhaust vents. Tip When choosing a location for wall-mounting the router, consider cable limitations and wall structure. To mount the router on a wall, follow these steps: Step 1 Determine the required distance between mounting holes on the router.
Chapter 2 Installing the Router Installing the Cisco 860, 880, 890 ISR Step 3 Hang the router on the screw without forcibly pushing towards the wall side. The screw head may damage the protection wall inside. Place the power adapter on a nearby horizontal surface. See Figure 2-38.
Chapter 2 Installing the Router Installing the Cisco 860, 880, 890 ISR Installing the Router Ground Connection The router must be connected to a reliable earth ground. Install the ground wire in accordance with local electrical safety standards. • For NEC-compliant grounding, use size 14 AWG (2 mm2) or larger copper wire and a ring terminal with an inner diameter of 1/4 in. (5 to 7 mm). • For EN/IEC 60950–compliant grounding, use size 18 AWG (1 mm2) or larger copper wire.
Chapter 2 Installing the Router Installing the Cisco 860, 880, 890 ISR Remove the four mounting screws of the top cover.
Chapter 2 Installing the Router Installing the Cisco 860, 880, 890 ISR Step 2 Install the left-side FIPS cover, as shown in detail A. 284922 Detail A Adapter Plate Step 3 Rotate and bring into the close position to hinge to the correct hexagon. Step 4 Place the adapter plate before closing by aligning the mounting holes.
Chapter 2 Installing the Router Installing the Cisco 860, 880, 890 ISR Secure the FIPS cover with two mounting screws. Step 6 Install the right-side FIPS cover the same way as the left-side FIPS cover. Step 7 View after both covers are installed.
Chapter 2 Installing the Router Installing the Cisco 860, 880, 890 ISR If the FIPS covers are installed with the rack mount brackets, the adapter plates are not required in the installation. 284925 Step 8 Installing Antennas for Cisco 890 Series The Cisco 890 series wireless routers have three reverse-polarity threaded Neill-Concelman (RP-TNC) connectors on the back panel. The antennas that are shipped with the router are dual-band 2.4-GHz to 5-GHz omnidirectional dipole antennas.
Chapter 2 Installing the Router Installing the Cisco 860, 880, 890 ISR To attach the radio antennas to your wireless router, follow these steps: Step 1 Manually screw the antennas tight to the RP-TNC connectors on the back of the router. Attaching Antennas to the Router 272486 Figure 2-40 Step 2 Orient the antennas. For optimum wireless performance, the antennas should be perpendicular with respect to the floor. a. If the router is being mounted on a desk, orient the antennas straight up. b.
Chapter 2 Installing the Router Installing the Cisco 860, 880, 890 ISR Antennas Oriented Vertically Up 274774 Figure 2-41 Cisco Integrated Services Router Hardware Installation Guide 2-50 OL-27407-01
Chapter 2 Installing the Router Installing the Cisco 860, 880, 890 ISR Antennas Oriented Vertically Down 274775 Figure 2-42 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 2-51
Chapter 2 Installing the Router Installing the Cisco 860, 880, 890 ISR Installing Cisco 890 Series in a Rack The Cisco 890 series ISRs can be mounted in a rack. To install a Cisco 890 series ISR in a rack, follow these steps: Step 1 Remove the screws, as shown in Figure 2-43. Figure 2-43 Screw Locations 1 1 1 Step 2 Caution 371427 1 Screws Using the screws provided, attach the rack-mount brackets to the Cisco 890 series ISR chassis, as shown in Figure 2-44. Use two screws on each side.
Chapter 2 Installing the Router Installing the Cisco 860, 880, 890 ISR Attaching the Rack-mount Brackets to the Cisco 890 Series ISR 272484 Figure 2-44 Caution Warning Step 3 Step 4 Chassis installation must allow unrestricted airflow for chassis cooling. To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to ensure that the system remains stable.
Chapter 2 Installing the Router Installing the Cisco 860, 880, 890 ISR Step 5 Connect the chassis to a reliable earth ground. For the chassis ground connection procedures, see the “Installing Cisco 890 Series in a Rack” section on page 2-52. Installing the C881G-B/S/V-K9 ISR To install the C881G-B/S/V-K9 ISR, follow the instructions in the “Installing the Cisco 860, 880, and 890 Series Routers” section on page 2-40.
Chapter 2 Installing the Router Installing the Cisco 860, 880, 890 ISR Figure 45 SIM Card Installation B 1 2 A 3 B 282316 A 4 Cisco Integrated Services Router Hardware Installation Guide OL-27407-01 2-55
Chapter 2 Installing the Router Installing the Cisco 860, 880, 890 ISR To install the SIM cards, follow these steps: Step 1 Open the door covering the SIM card slots. a. Insert the tip of the screw driver into the upper latch and gently disengage it as shown in the figure. b. Remove the door as shown. Step 2 To insert a SIM card into the SIM 0 slot, hold the SIM card with the contacts facing up as shown and gently push the card into place until it locks in.
CH A P T E R 3 Connecting the Router This chapter describes how to install the Cisco 860, 880, 890 ISRs and the Cisco 819 ISR. • Cisco 810 Series, page 3-1 • Cisco 860, 880, 890 Series, page 3-8 Cisco 810 Series Cisco 819 Series This section describes how to connect Cisco 819 ISRs to Ethernet devices and a network.
Chapter 3 Connecting the Router Cisco 810 Series Preventing Damage to the Router To prevent damage to your router, follow these guidelines when connecting devices to your router: • Caution Turn off power to the devices and to the router until all connections are completed. Do not turn on the devices until after you have completed all connections to the router. • If you must supply your own cable, see the “Cisco 860, 880, 890 Series” section on page A-11 for cabling specifications.
Chapter 3 Connecting the Router Cisco 810 Series Step 3 Note (Optional) Connect additional servers, PCs, or workstations to the other Ethernet switch ports. Use the Cisco Configuration Express to configure the Internet connection settings. See Cisco Configuration Professional Quick Start Guide for more information.
Chapter 3 Connecting the Router Cisco 810 Series Connecting a Terminal or PC to the Console Port Connect a terminal or PC to the Console port either to configure the software by using the CLI or to troubleshoot problems with the router. To connect a terminal or PC to the console port on the router and access the CLI, follow these steps: Step 1 Connect the RJ-45 end of a DB-9-to-RJ-45 serial cable to the RJ-45 Console port on the router.
Chapter 3 Connecting the Router Cisco 810 Series Connecting a Modem to the Console Port To connect a modem to the router, follow these steps: Step 1 Connect the RJ-45 end of the adapter cable to the Console port on the router as shown in Figure 3-4. Figure 3-4 Connecting a Modem to the Console Port 1 3 4 245587 2 Step 2 Connect the DB-9 end of the console cable to the DB-9 end of the modem adapter. Step 3 Connect the DB-25 end of the modem adapter to the modem.
Chapter 3 Connecting the Router Cisco 810 Series To connect your Cisco 819 ISR to an AC power outlet, follow these steps: Step 1 Connect the AC adapter to an AC power outlet. Step 2 Plug the adapter cord into the router. Connecting the DC Adapter Warning This product relies on the building’s installation for short-circuit (overcurrent) protection.
Chapter 3 Connecting the Router Cisco 810 Series Figure 3-6 DC Power Supply PWR2-20W-12VDC and PWR2-20W-24VDC 2 1 302438 3 Step 2 1 Black wire (negative) 2 White wire (positive) 3 Adapter Plug the adapter cord into the router. Note The power adapters have 18 AWG wires for the input connection. Tinned bare wires are used for the input connection as there is no standard established for connector type. Screw terminal blocks are most often used.
Chapter 3 Connecting the Router Cisco 860, 880, 890 Series Table 3-1 Verifying the Router Operation (continued) Power and Link LEDs to Check Normal Patterns ACT Green Network activity on FE Switch ports, GE WAN port, 3G cellular interface, and serial interfaces. Off No network activity. Cisco 860, 880, 890 Series This section describes how to connect Cisco 860 series, Cisco 880 series, and Cisco 890 series ISRs to Ethernet devices, Power over Ethernet (PoE), and a network.
Chapter 3 Connecting the Router Cisco 860, 880, 890 Series Note The illustrations in this chapter show a wireless router with antennas attached. Non-wireless routers do not have antennas or antenna connectors on the back panel. However, the procedures for connecting devices to the router are the same for both wireless and non-wireless routers. Safety Warnings Warning When installing the product, please use the provided or designated connection cables/power cables/AC adaptors/batteries.
Chapter 3 Connecting the Router Cisco 860, 880, 890 Series Warning Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. Statement 1036 Warning Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. Statement 1037 Warning Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.
Chapter 3 Connecting the Router Cisco 860, 880, 890 Series Preventing Damage to the Router To prevent damage to your router, follow these guidelines when connecting devices to your router: • Caution Turn off power to the devices and to the router until all connections are completed. Do not turn on the devices until after you have completed all connections to the router. • Connect the color-coded cables supplied by Cisco to the color-coded ports on the back panel.
Chapter 3 Connecting the Router Cisco 860, 880, 890 Series Connecting a PC, Server, or Workstation To connect a PC (or other Ethernet devices) to an Ethernet switch port, follow these steps: Step 1 Connect one end of the yellow Ethernet cable to an Ethernet switch port on the router. Figure 3-1 shows a Cisco 888W router connected to a PC.
Chapter 3 Connecting the Router Cisco 860, 880, 890 Series Connecting a Phone To connect an 802.3af-compliant phone to an Ethernet switch port, follow these steps: Note A power source must be provided for the phone to function. This can be done in two ways: the phone can be powered via the PoE function using the PoE enabled Ethernet ports, or by using an external AC power source connected to the phone.
Chapter 3 Connecting the Router Cisco 860, 880, 890 Series Step 2 Connect the other end of the cable to the RJ-45 port on the phone. Connecting an External Ethernet Switch If more than four PCs in an office must be connected to each other, you can add Ethernet connections to the router by connecting an external Ethernet switch to the Ethernet switch on the router.
Chapter 3 Connecting the Router Cisco 860, 880, 890 Series Connecting the V.92 modem Port Warning Hazardous network voltages are present in WAN ports regardless of whether power to the unit is OFF or ON. To avoid electric shock, use caution when working near WAN ports. When detaching cables, detach the end away from the unit first. Statement 1026 To connect the router to your service provide network through the V.
Chapter 3 Connecting the Router Cisco 860, 880, 890 Series Connecting a Terminal or PC to the Console Port Connect a terminal or PC to the Console Auxiliary (Aux) port either to configure the software by using the CLI or to troubleshoot problems with the router. To connect a terminal or PC to the console port on the router and access the CLI, follow these steps: Connect the RJ-45 end of a DB-9–to–RJ-45 serial cable to the RJ-45 Console Aux port on the router.
Chapter 3 Connecting the Router Cisco 860, 880, 890 Series When the terminal emulator establishes communications, the router prompt is displayed. For more information on terminal emulation settings, see Applying Correct Terminal Emulator Settings for Console Connections. Connecting a Modem to the Auxiliary Port To connect a modem to the router, follow these steps: Step 1 Connect the RJ-45 end of the adapter cable to the Aux port on the router as shown in Figure 3-4.
Chapter 3 Connecting the Router Cisco 860, 880, 890 Series Connecting the 3G Card Note For information on embedded multiband, multiservice WAN modems, see Configuring Cisco EHWIC and 880G for 3G (EV-DO Rev A) and Configuring Cisco EHWIC and 880G for 3.7G (HSPA+)/3.5G (HSPA). Note The Cisco 880G router does not support online insertion and removal (OIR) of the 3G card. You must enter the shutdown command on the cellular interface before you remove the 3G card from the router.
Chapter 3 Connecting the Router Cisco 860, 880, 890 Series Figure 3-13 Inserting the 3G Card 4 271473 3 2 3 1 5 6 5 1 3G card with the Cisco logo facing up 4 Screw holes for locking bracket 2 3G express card slot 5 Pin holes for aligning the locking bracket 3 Notches on the 3G card 6 SIM slot (in HSPA1 cards only) 1. HSPA = High-Speed Packet Access. Open the top of the anti-theft locking bracket, as shown in Figure 3-14.
Chapter 3 Connecting the Router Cisco 860, 880, 890 Series Step 3 Slide the opened locking bracket under the 3G card. The locking bracket should align with the notches on either side of the 3G card, as shown in Figure 3-15, and the pins on the locking bracket should be inserted into the corresponding holes in the router.
Chapter 3 Connecting the Router Cisco 860, 880, 890 Series Step 4 Close the locking bracket, as shown in Figure 3-16. Figure 3-16 Closing the Locking Bracket 1 271580 2 1 Step 5 2 3G card Locking bracket Insert the screws, as shown in Figure 3-17, and tighten with a number 2 Phillips screwdriver.
Chapter 3 Connecting the Router Cisco 860, 880, 890 Series The antenna connector receptacle may be located on the left, right, or front of the 3G card, depending on your card. Note Figure 3-18 and Figure 3-19 show the antenna connected to the 3G card with an SSMB type plug, and the antenna with the SMK-TS-9 connector. Figure 3-18 Antenna connected to the 3G Card with SSMB connector 272653 1 3 2 1 Antenna on a cradle 2 Antenna SSMB connector 3 Antenna connector receptacle1 1.
Chapter 3 Connecting the Router Cisco 860, 880, 890 Series Antenna with the SMK-TS- 9 Connector 279085 Figure 3-19 Original antenna assembly SMK-TS-9 connector Cable If you are using an extension cable, you must attach the 3G adapter for extended cable antenna to the body of the router. Depending on the SKU ordered, the adapters come with different connectors. Table 3-2 lists the different adapters and SKUs supported by each adapter.
Chapter 3 Connecting the Router Cisco 860, 880, 890 Series Step 8 Remove the protective tape from the adhesive on the bottom of the antenna cradle, then firmly press the cradle to the flat surface. Installing the 3G Adapter for Extended Cable/Antenna For better signal and reception, if you are using the Cisco 3G Adapter for Extended Cable/Antenna, 3G-ACC-SMKTS9-TNC, follow these steps to install it: Step 1 Locate and remove the Phillips screw on the left side of the router as shown in Figure 3-20.
Chapter 3 Connecting the Router Cisco 860, 880, 890 Series Step 2 Locate the hooks on the adapter as shown in Figure 3-21. Figure 3-21 Locating the Hooks on the Adapter 279122 1 1 Step 3 Hooks on the adapter Align and insert the hooks of the adapter into the air vent holes on the left side router body as shown in Figure 3-22. Figure 3-22 Inserting the Hooks 1 1 279123 1 Hooks aligned and inserted into the router.
Chapter 3 Connecting the Router Cisco 860, 880, 890 Series Step 4 Align the circular adapter hole with the hole on the router chassis from where you removed the screw in Step 1 and use the screw to attach the adapter to the router as shown in Figure 3-23.
Chapter 3 Connecting the Router Cisco 860, 880, 890 Series Step 5 Connect the extension cable to the 3G card, as described in the “Connecting the 3G Card” section on page 3-18. The complete assembly is shown in Figure 3-24.
Chapter 3 Connecting the Router Cisco 860, 880, 890 Series Table 3-3 Note Cisco Adapter Cables for Use with 3G Fixed Routers Cisco Product Number Antenna Adapter Length Insertion Loss Frequency (MHz) 3G-ACC-SSMB-TNC 14.5 inches 0.66 dB 2100 3G-ACC-TS9-TNC 13.5 inches 0.62 dB 2100 Antenna orientation can increase or decrease signal reception due to polarization.
Chapter 3 Connecting the Router Cisco 860, 880, 890 Series To connect the Data BRI port to the ISDN service provider, follow these steps: Note Step 1 Although the following procedure shows a Cisco 888W data router, this procedure applies to all Cisco 880 series router with a Data BRI port. Connect one end of the orange ISDN S/T cable to the Data BRI port on the router. Figure 3-25 shows a Data BRI connection.
Chapter 3 Connecting the Router Cisco 860, 880, 890 Series Step 4 Connect the second unshielded Category 5 cable from the telecommunication service port on the splitter to the wall jack to allow a link to the network service provider. Connecting an FE Line to an FE WAN Port To connect the Fast Ethernet (FE) WAN port on the router, follow these steps: Step 1 Connect one end of the yellow cable to the FE WAN port as shown in Figure 3-26.
Chapter 3 Connecting the Router Cisco 860, 880, 890 Series Connecting a GE Line to an GE WAN Port To connect the Gigabit Ethernet (GE) WAN port on the router, follow these steps: Step 1 Connect one end of the yellow cable to the GE WAN port as shown in Figure 3-27. Connecting the GE WAN Port 274493 Figure 3-27 1 2 3 Internet Step 2 1 GE WAN port 2 CAT 5 cable 3 Modem connected to the Internet Connect the other end of cable to an available port on the modem.
Chapter 3 Connecting the Router Cisco 860, 880, 890 Series Caution Cisco Systems DSL WAN Interfaces are tested for compliance with regulatory standards such as FCC Part 68, ITU-T K.21, IEC 61000-4-5, and CSA/EN/IEC/UL 60950-1. These standards assume Primary Protection devices protect the Customer Premise Equipment (CPE).
Chapter 3 Connecting the Router Cisco 860, 880, 890 Series Figure 3-28 Primary Protection Device Location Telecom Service Overhead Service Entrance Home or Business Router Service Utilities Entrance or Demarcation Point Network Interface Box/ Network Interface Device/ Station Protector Note: Primary Protection may be located Outside or Inside of Premise Building Ground Rod connected to Service entrance and Primary Protection 281392 * Alternative Underground Service Entrance To connect the router t
Chapter 3 Connecting the Router Cisco 860, 880, 890 Series Caution Note The primary WAN port is designed for an RJ-45 connector only. Damage to the primary WAN port may occur if a non-RJ-45 connector is inserted. The DSL line must be provisioned by your service provider and correctly configured so that the LED shows the carrier detect (CD) status. On Cisco 860VAE routers, check the DSL Link LED. Connecting Power over Ethernet Warning This unit might have more than one power supply connection.
Chapter 3 Connecting the Router Cisco 860, 880, 890 Series Figure 3-30 Connecting PoE for the Cisco 880 and the Cisco 890 Series Routers 1 4 5 3 2 2 6 231995 4 1 48-VDC PoE input jack 4 AC plug 2 Power cord 5 12-VDC input power-jack plug 3 Power adapter—48 VDC 6 Power adapter—12 VDC The Cisco 880 series ISRs with embedded WLAN antennas require a single external power supply: a 30-W power supply for non-POE-enabled routers or a 60-W power supply for POE-enabled routers.
Chapter 3 Connecting the Router Cisco 860, 880, 890 Series To connect your Cisco 860 series, Cisco 880 series, or the Cisco 890FSP ISR to an AC power outlet, follow these steps: Step 1 Connect the router to an AC power outlet as shown in Figure 3-31. To connect the AC power outlet for the Cisco 892FSP router, see Figure 3-32.
Chapter 3 Connecting the Router Cisco 860, 880, 890 Series Figure 3-32 Connecting the AC Adapter for the Cisco 892FSP 7 GE WAN 6 GE LAN 5 Cisco 892FSP 4 CONSOLE GE WAN SFP RESET 9 8 AUX 8 12VDC 2.5A 1 2 3 1 12-VDC plug 3 Power adapter—12 VDC 2 Power Adapter Cord 4 AC Plug Figure 3-33 343746 4 Cisco 892FSP, 896VA, 897VA, and 898EA Power Adapter Connector Pin Assignment Pin 4 Pin 2 284800 Pin 3 Pin 1 Pin 1 Ground Pin 3 +12 V Pin 2 1 Pin 4 NC NC 1.
Chapter 3 Connecting the Router Cisco 860, 880, 890 Series Step 2 To secure the power cord to the router, attach the power lock clip to the power cord, slide the clip to the end of the DC plug, and secure the retaining clip into the router chassis. See Figure 3-34.
Chapter 3 Connecting the Router Cisco 860, 880, 890 Series Step 3 Snap the latches into the holes on either side of the power connector. See Figure 3-35. Figure 3-35 Power Lock Clip Latched Into the Holes on Either Side of the Power Connector 1 4 3 270800 2 1 Power lock clip 3 Power adapter 2 Power cord 4 AC plug Connecting an FXS Line Use a standard straight-through RJ-11 modular telephone cable to connect a Foreign Exchange Service (FXS) port to a telephone or fax machine.
Chapter 3 Connecting the Router Cisco 860, 880, 890 Series To connect the FXS line, follow these steps: Step 1 Connect one end of the straight-through RJ-11 cable to the FXS port. Figure 3-36 shows an FXS line connection. Figure 3-36 Connecting an FXS Line 1 2 241907 3 Fax machine or telephone Step 2 1 FXS port 2 RJ-11 cable 3 RJ-11 port Connect the other end of the cable to the RJ-11 port on the fax machine or telephone.
Chapter 3 Connecting the Router Cisco 860, 880, 890 Series Warning Hazardous network voltages are present in WAN ports regardless of whether power to the unit is OFF or ON. To avoid electric shock, use caution when working near WAN ports. When detaching cables, detach the end away from the unit first. Statement 1026 To connect the FXO line, follow these steps: Step 1 Connect one end of the straight-through RJ-11 cable to the FXO port. See Figure 3-37.
Chapter 3 Connecting the Router Cisco 860, 880, 890 Series This option allows a stepped offhook resistance during seizure, which avoids overloading the circuit during offhook in the event that ringing voltage is present on the circuit at the same time as the trunk seizure. The stepped offhook resistance is initially set to 800 Ohms, then adjusts to 50 Ohms when ringing voltage is not present.
Chapter 3 Connecting the Router Cisco 860, 880, 890 Series Figure 3-38 shows a voice BRI line connection. Figure 3-38 Connecting a Voice BRI Line 1 2 241906 3 Step 2 1 Voice BRI port 2 RJ-45 cable 3 Telephone outlet Connect the other end of the cable to the RJ-45 telephone outlet or other device. Warning Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into beams or view directly with optical instruments.
Chapter 3 Connecting the Router Cisco 860, 880, 890 Series Warning Ultimate disposal of this product should be handled according to all national laws and regulations. Statement 1040 Warning Invisible laser radiation may be emitted from the end of the unterminated fiber cable or connector. Do not view directly with optical instruments. Viewing the laser output with certain optical instruments (for example, eye loupes, magnifiers, and microscopes) within a distance of 100 mm may pose an eye hazard.
Chapter 3 Connecting the Router Cisco 860, 880, 890 Series Verifying Connections To verify that all devices are properly connected to the router, first turn on all the connected devices, then check the LEDs. To verify router operation, refer to Table 3-1. For the full LED descriptions, see the “LEDs” section on page 1-79. Table 3-4 Verifying the Router Operation Power and Link LEDs to Check Normal Patterns Power OK On when power is supplied to the router.
Chapter 3 Connecting the Router Cisco 860, 880, 890 Series Table 3-4 Verifying the Router Operation (continued) Power and Link LEDs to Check Normal Patterns To wireless LAN WLAN LINK Wireless LAN link status: WLAN 2.4 GHz WLAN 5.0 GHz PoE14 PoE 0 (880 and 890 series only) PoE 1 (880 and 890 series only) • Green if at least one client is associated. • Off if no client is associated. Wireless LAN 2.
Chapter 3 Connecting the Router Cisco 860, 880, 890 Series Table 3-4 Verifying the Router Operation (continued) Power and Link LEDs to Check Normal Patterns To WAN GE line (860VAE models only) GE Mode On when GE WAN mode is selected. Off when the device is powered off or when DSL WAN mode is selected. GE ACT On when the GE WAN interface is up. Blinking when there is GE WAN activity (traffic in either direction). Off when the device is powered off or when the GE WAN interface is down. 1.
Chapter 3 Connecting the Router Cisco 860, 880, 890 Series Cisco Integrated Services Router Hardware Installation Guide 3-48 OL-23125-02
CH A P T E R 4 Initial Configuration This chapter provides instructions for initial configuration of the Cisco 819, 860, 880, 890 Series Integrated Services Routers (ISRs), and contains the following sections: • Cisco 810 Series, page 4-1 • Cisco 860, 880, 890 Series, page 4-2 Cisco 810 Series Cisco 819 Series This section provides instructions for initial configuration of the Cisco 819 ISRs. For the initial configuration, we recommend using Cisco Configuration Professional Express.
Chapter 4 Initial Configuration Cisco 860, 880, 890 Series Verifying the Initial Configuration For more information, refer to the “Verifying the Initial Configuration” section on page 4-6. Cisco 860, 880, 890 Series This section provides instructions for initial configuration of the Cisco 860 series, 880 series, and 890 series ISRs. You may also initially configure your router by using the Cisco IOS command-line interface (CLI) or by using the setup command facility.
Chapter 4 Initial Configuration Cisco 860, 880, 890 Series Please change these publicly known initial credentials using Cisco CP Express or the Cisco IOS CLI. Here are the Cisco IOS commands. username privilege 15 secret 0 no username username1 Replace and with the username and password you want to use. For more information about Cisco CP please follow the instructions in the QUICK START GUIDE for your router... ...
Chapter 4 Initial Configuration Cisco 860, 880, 890 Series Setup Command Facility The setup command facility guides you through the configuration process by prompting you for the specific information that is needed to configure your system. Use the setup command facility to configure a hostname for the router, to set passwords, and to configure an interface for communication with the management network.
Chapter 4 Initial Configuration Cisco 860, 880, 890 Series Step 5 Enter a hostname for the router (this example uses Router). Configuring global parameters: Enter host name [Router]: Router Step 6 Enter an enable secret password. This password is encrypted (more secure) and cannot be seen when viewing the configuration. The enable secret is a password used to protect access to privileged EXEC and configuration modes. This password, after entered, becomes encrypted in the configuration.
Chapter 4 Initial Configuration Cisco 860, 880, 890 Series The configuration is displayed: The following configuration command script was created: hostname Router enable secret 5 $1$D5P6$PYx41/lQIASK.HcSbfO5q1 enable password xxxxxx line vty 0 4 password xxxxxx snmp-server community public ! no ip routing ! interface FastEthernet4 no shutdown speed 100 duplex auto ip address 172.1.2.3 255.255.0.0 ! Step 12 Respond to the following prompts. Enter 2 to save the initial configuration.
Chapter 4 Initial Configuration Cisco 860, 880, 890 Series Initial Configuration of the Wireless Access Point The embedded wireless access point (AP) runs its own IOS.
Chapter 4 Initial Configuration Cisco 860, 880, 890 Series Cisco Integrated Services Router Hardware Installation Guide 4-8 OL-23125-02
A P P E N D I X A Technical Specifications This appendix provides specifications for the Cisco 860, 880, 890 Series ISRs, Cisco 819 ISRs, and the Cisco 812 ISRs: • Cisco 810 Series, page A-1 • Cisco 860, 880, 890 Series, page A-11 Cisco 810 Series This section contains the following: • Cisco 812 Series, page A-1 • Cisco 819 Series, page A-4 Cisco 812 Series This section provides specifications for the Cisco 812 Integrated Services Router (ISRs) and contains the following topics: Warning Note •
Appendix A Technical Specifications Cisco 810 Series Table A-1 Cisco 812 ISR Specifications Description C812G+7-K9 C812G-CIFI+7-E-K9 C812G-CIFI+7-N-K9 C812G-CIFI-V-A-K9 C812G-CIFI-S-A-K9 (3G only) (3G + WiFi) Physical Characteristics Dimensions (H x W x D) 2.01 x 8.95 x 9.49 inches (51 x 227x 241 mm) Weight 3.96 lbs (1.
Appendix A Technical Specifications Cisco 810 Series Table A-1 Cisco 812 ISR Specifications (continued) C812G+7-K9 C812G-CIFI+7-E-K9 C812G-CIFI+7-N-K9 C812G-CIFI-V-A-K9 C812G-CIFI-S-A-K9 Description (3G only) (3G + WiFi) Radio Immunity EN301 489-1, EN 301 489-7, and EN301 489-24 Transportation/Storage Conditions Temperature –40 to158 °F (–40 to 70°C) Humidity 5–95% Altitude 4570 m (15,000 ft) AC Power Adapter Power Source 100–240 VAC In-ceiling Plenum No IP41 No Extended Shock-vibe N
Appendix A Technical Specifications Cisco 810 Series Mean Time Between Failure Ground Benign Environment Table A-2 lists the Mean Time Between Failure (MTBF) values for Cisco 812 ISRs. The MTBF is calculated based on the Ground Benign condition. The values may be adjusted based on the different router usage.
Appendix A Technical Specifications Cisco 810 Series Table A-3 Cisco 819 ISR Specifications Hardened Design Specification Non-Hardened Design Specifications (Cisco 819HG and Cisco 819HG-4G ISRs) (Cisco 819G and Cisco 819G-4G ISRs) (C819HGW and C819HWD ISRs) 1.73 x 7.7 x 8.1 in 1.67 x 7.7 x 7.2 in 1.73 x 7.7 x 9.0 in (44 x 196 x 206 mm) (42 x 196 x 183 mm) (44 x 196 x 229 mm) Weight 3.3 lb (1.5 kg) 2.3 lb (1.0 kg) 3.4 lb (1.
Appendix A Technical Specifications Cisco 810 Series Table A-3 Cisco 819 ISR Specifications (continued) Hardened Design Specification Non-Hardened Design Specifications (Cisco 819HG and Cisco 819HG-4G ISRs) (Cisco 819G and Cisco 819G-4G ISRs) Hardened Design Specifications Description (C819HGW and C819HWD ISRs) UL 60950-1, 2nd edition; CAN/CSA C22.2 No.
Appendix A Technical Specifications Cisco 810 Series Table A-3 Cisco 819 ISR Specifications (continued) Hardened Design Specification Non-Hardened Design Specifications Description (Cisco 819HG and Cisco 819HG-4G ISRs) (Cisco 819G and Cisco 819G-4G ISRs) Altitude Operating: –500 to 10,000 ft, de-rating operating temperature 1°C per 1,000 feet Hardened Design Specifications (C819HGW and C819HWD ISRs) Non-operating: –1,000 to 30,000 ft Cable Length Input cable: 1 m Output cable: 1.
Appendix A Technical Specifications Cisco 810 Series Table A-3 Cisco 819 ISR Specifications (continued) Hardened Design Specification Non-Hardened Design Specifications (Cisco 819HG and Cisco 819HG-4G ISRs) (Cisco 819G and Cisco 819G-4G ISRs) Hardened Design Specifications Description (C819HGW and C819HWD ISRs) Antenna (Diversity and Antenna 3G-ANTM1919D) Antenna Dimensions 7.63 x 0.94 x 0.63 in (19.38 x 2.39 x 1.
Appendix A Technical Specifications Cisco 810 Series Table A-4 MTBF Values (continued) SKUs MTBF (hours) C819HGW-S-A-K9 220,000 C819HGW-V-A-K9 C819HGW+7-E-K9 293,000 C819HGW+7-N-K9 C819HGW+7-A-A-K9 C819HWD-E-K9 630,000 C819HWD-A-K9 C819H-K9 1,000,000 Cisco 819HG-4G and Cisco 819G-4G ISRs C819HG-4G-V-K9 214,000 C819G-4G-V-K9 C819HG-4G-A-K9 226,000 C819G-4G-A-K9 C819HG-4G-G-K9 293,000 C819G-4G-G-K9 Supported Power Adapters Table A-5 and Table A-6 list the supported power adapters for Cis
Appendix A Technical Specifications Cisco 810 Series Table A-5 Cisco 819G ISR Power Adapters C819G-4G-A-K9 C819G-4G-V-K9 C819G-4G-G-K9 C819G+7-K9 C819G-B-K9 C819G-S-K9 C819G-U-K9 C819G-V-K9 Power Adapter Nominal Input Range (4G LTE SKUs) (3GSKUs) Martek MBRH 0500-D/2Q21 24 VDC Yes Yes Martek MBRH 0500-D/2Q21 52 VDC Yes Yes Martek MBRH 0500-D/2Q21 72 VDC Yes Yes Martek MBRH 0500-D/2Q21 110 VDC Yes Yes Martek MBRH 0500-B/Q22 24 VDC Yes — Martek MBRH 0500-C/Q22 52 VDC Yes — M
Appendix A Technical Specifications Cisco 860, 880, 890 Series Table A-6 Cisco 819H ISR Power Adapters (continued) C819HG+7-K9 C819HGW-S-A-K9 C819HG-4G-A-K9 C819HG-B-K9 C819HGW-V-A-K9 C819HG-4G-V-K9 C819HG-S-K9 C819HGW+7-E-K9 C819HWD-E-K9 C819HG-4G-G-K9 C819HG-U-K9 C819HGW+7-N-K9 C819HG-V-K9 C819HGW+7-A-A-K9 C819HWD-A-K9 C819H-K9 Nominal Input Range (4G LTE SKUs) (3G SKUs) (3G + WiFi SKUs) (WiFi SKUs) (Serial SKU) Martek MBRH 0500-D/2Q21 24 VDC Yes Yes Yes Yes Yes Martek MBRH 0500-D/2Q21
Appendix A Technical Specifications Cisco 860, 880, 890 Series Warning • G.SHDSL Port Connector Pinouts, page A-25 • Data BRI Port Connector Pinouts, page A-26 • Voice ISDN BRI Interface Pin Numbers and Functions, page A-27 • SFP Port Connector Pinouts, page A-27 • Cable Specifications, page A-28 Ultimate disposal of this product should be handled according to all national laws and regulations.
Appendix A Technical Specifications Cisco 860, 880, 890 Series Table A-7 Router Specifications Design Specification (all models except Cisco 860VAE series) Description Physical Dimensions Dimensions with antenna and rubber feet (H x W x D) 1.9 x 12.8 x 10.4 in. Weight (not including desktop power supply) 5.5 lb (2.
Appendix A Technical Specifications Cisco 860, 880, 890 Series Cisco 860VAE Series Table A-8 lists the system specifications for the Cisco 860VAE series routers. Table A-8 Router Specifications Description Design Specification Cisco 860VAE series Physical Dimensions Dimensions with antenna and rubber feet (H x W x D) 1.75 x 9.5 x 9 in. Weight (not including desktop power supply) 3.3 lb (1.5 kg) The total weight depends on customer-selected options.
Appendix A Technical Specifications Cisco 860, 880, 890 Series Table A-8 Router Specifications (continued) Design Specification Cisco 860VAE series Description Operating temperature -5 to 45° C Operating humidity 10% to 90%, non condensing Cisco 860VAE-W-A-K9, Cisco 860VAE-W-E-K9, and Cisco 860VAE-POE-W-A-K9 Series Table A-9 lists the system specifications for the Cisco 860VAE-W-A-K9, Cisco 860VAE-W-E-K9, and Cisco 860VAE-POE-W-A-K9 series routers.
Appendix A Technical Specifications Cisco 860, 880, 890 Series Table A-9 Technical Specifications Description Specification Radio technology IEEE 802.11n draft 2.0 standard compliant. Backward compatible with 802.11b/g. Operating Frequency 2.4 GHz radio band Bandwidth 20 MHz Channels Country-specific: America SKU(-W-A): Channels 1–11 Europe SKU(-W-E): Channels 1–13 Cisco 870 Series Table A-12 lists the system specifications for the Cisco 870 series routers.
Appendix A Technical Specifications Cisco 860, 880, 890 Series Table A-10 Router Specifications (continued) Description Design Specification Nonoperating altitude 0 to 15,000 ft (0 to 4570m) Operating temperature 32 to 104°F (0 to 40°C) Operating humidity 10 to 85%, relative humidity (noncondensing) Operating altitude 0 to 10,000 ft (0 to 3000m) Power Supply AC input voltage 100 to 240 VAC Frequency 50 to 60 Hz Maximum output power 26W Output voltages 5 and 12V Optional external Inline
Appendix A Technical Specifications Cisco 860, 880, 890 Series Table A-11 Router Specifications Description Design Specification Physical Dimensions Nonwireless models (H x W x D): • 1.9 x 12.8 x 9.8 in. (48 x 325 x 249 mm) (includes rubber feet) • 1.75 x 12.8 x 9.8 in. (44 x 325 x 249 mm) (without rubber feet) Wireless models (H x W x D): External Power Supply • 1.9 x 12.8 x 10.4 in. (48 x 325 x 264 mm) (includes rubber feet) • 1.75 x 12.8 x 10.4 in.
Appendix A Technical Specifications Cisco 860, 880, 890 Series Cisco 880G Series 3G Wireless Integrated Services Router Table A-12 lists the system specifications for the Cisco 880G series 3G Wireless Integrated Services routers. Table A-12 Router Specifications Description Design Specification Physical Dimensions Nonwireless models • H x W X D = 1.9 x 12.8 x 9.8 in. (48 x 325 x 249 mm) (includes rubber feet) • H x W X D = 1.75 x 12.8 x 9.8 in.
Appendix A Technical Specifications Cisco 860, 880, 890 Series Table A-13 Router Specifications Description Design Specification Physical Dimensions Nonwireless models: • H x W x D = 1.9 x 12.8 x 9.8 in. (48 x 325 x 249 mm) (includes rubber feet) • H x W x D = 1.75 x 12.8 x 9.8 in. (44 x 325 x 249 mm) (without rubber feet) Wireless models: • H x W x D = 1.9 x 12.8 x 10.4 in. (48 x 325 x 264 mm) (includes rubber feet) • H x W x D = 1.75 x 12.8 x 10.4 in.
Appendix A Technical Specifications Cisco 860, 880, 890 Series Cisco 890 Series Table A-12 lists the system specifications for the Cisco 890 series routers. Table A-14 Router Specifications Description Design Specification Physical Dimensions Cisco 891, 892, and 892F Nonwireless models: • H x W x D = 1.9 x 12.8 x 9.8 in. (4.8 x 32.5 x 24.9 cm) (includes rubber feet) • H x W x D = 1.75 x 12.8 x 9.8 in. (4.5 x 32.5 x 24.9 cm) (without rubber feet) Wireless models: • H x W x D = 1.9 x 12.8 x 10.4 in.
Appendix A Technical Specifications Cisco 860, 880, 890 Series Table A-14 Router Specifications (continued) Description Design Specification Optional POE External output voltage • Separate 80W POE power supply for Cisco 891 and 892 ISRs • Single 125W power supply required for Cisco 896, 897, 898 and 891F for router and PoE 48 VDC Power Supply Table A-15 lists the maximum input values for the power supply used with the Cisco 860, 880, 890 series ISRs.
Appendix A Technical Specifications Cisco 860, 880, 890 Series FE and GE Port Pinouts Table A-17 describes the RJ-45 connector pinouts for Fast Ethernet (FE) ports with Power over Ethernet (PoE). Some models support PoE using an optional module, and some models do not support PoE. For ports that do not support PoE, pins 4, 5, 7, and 8 are not connected. • Cisco 860VAE and 860VAE-K9 ISRs do not support PoE. • Cisco 880 series ISRs can include an optional PoE module that provides power to 802.
Appendix A Technical Specifications Cisco 860, 880, 890 Series Console and Auxiliary Port Connector Pinouts Table A-19 lists the pinouts for the console and auxiliary port connectors. Table A-19 Console and Auxiliary Port Connector Pinouts RJ-45 Pin Function 1 RTS 2 DTR 3 TXD 4 GND 5 GND 6 RXD 7 DSR 8 CTS FXS and FXO Port Connector Pinouts Table A-20 lists the FXS and FXO connector pinouts.
Appendix A Technical Specifications Cisco 860, 880, 890 Series Table A-21 VDSL2 Connector Pinouts (RJ-11-to-RJ-45) (continued) RJ-11 Pin Function 5 Unused 6 Unused ADSL2+ Port Connector Pinouts Table A-22 lists the ADSL2+ connector pinouts. Table A-22 ADSL2+ Connector Pinouts (RJ-11) RJ-11 Pin Function 1 Unused 2 Unused 3 TIP 4 RING 5 Unused 6 Unused V.92 Port Connector Pinouts Table A-23 lists the V.92 connector pinouts. Table A-23 V.
Appendix A Technical Specifications Cisco 860, 880, 890 Series Table A-24 G.SHDSL WAN Port Pinouts for Two-Pair Products Pin Function 1 Unused 2 TIP (Port1) 3 TIP (Port0) 4 RING (Port0) 5 RING (Port1) 6 Unused Table A-25 lists the pinouts for the symmetrical high-speed DSL (G.SHDSL) WAN port for four-pair products, including the following router models: • C888E • C888EW • C888EA Table A-25 G.
Appendix A Technical Specifications Cisco 860, 880, 890 Series Table A-26 Data BRI Port Pinouts (continued) Pin Function 7 Unused 8 Unused Voice ISDN BRI Interface Pin Numbers and Functions Table A-27 lists the interface pin numbers and functions for the voice ISDN BRI port. Table A-27 Interface Pin Numbers and Functions ISDN BRI NT/TE Card NT Interface1 TE Interface2 Pin 3/T+ Pin 3/R+ Pin 3/T+ Pin 4/R+ Pin 4/T+ Pin 4/R+ Pin 5/R- Pin 5/T- Pin 5/R- Pin 6/T- Pin 6/R- Pin 6/T- 1.
Appendix A Technical Specifications Cisco 860, 880, 890 Series Table A-28 SFP Port Pinouts (continued) Pin Function 16 Transmitter power 17 Transmitter ground 18 Transmit data in 19 Inverted transmit data in 20 Transmitter ground Cable Specifications This section provides specifications for the following Ethernet cables: • Straight-through cable • Crossover cable Because of the autocrossover (autosensing) function, both straight-through and crossover cables can be used for the Ethernet
