Cisco IE 3000 Switch Getting Started Guide • About This Guide, page 1 • Taking Out What You Need, page 2 • Connecting Expansion Modules, page 3 • Running Express Setup, page 5 • Managing the Switch, page 9 • Installing the Switch, page 11 • Connecting to the Switch Ports, page 21 • In Case of Difficulty, page 25 • Obtaining Documentation and Submitting a Service Request, page 28 • Cisco One-Year Limited Hardware Warranty Terms, page 28 About This Guide This guide provides instructions on
Cisco IE 3000 Switch Getting Started Guide For additional installation and configuration information for Cisco IE 3000 switches, see the Cisco IE 3000 documentation on Cisco.com. For system requirements, important notes, limitations, open and resolved bugs, and last-minute documentation updates, see the release notes, also on Cisco.com. When you use the online publications, refer to the documents that match the Cisco IOS software version running on the switch.
Cisco IE 3000 Switch Getting Started Guide Figure 1 Cisco IE 3000 Shipping Box Contents 1 2 D h it c w S n 00 atio 30 n t IE me co c u is o C D 3 oc um V RT A A C n tio ta D en 4 201876 V RT A A 1 Cisco IE 3000 switch1 3 Power and relay connectors 2 Documentation 4 Console cable (RJ-45-to-DB-9 adapter cable) 1. The Cisco IE-3000-4TC is shown as an example. Your switch model might look different.
Cisco IE 3000 Switch Getting Started Guide Follow these steps to connect the expansion modules to the switch. Remove the right side panel by firmly grasping both sides in the middle and pulling it outward. If necessary, use a flat-blade screwdriver to pry open the side panel. Step 2 Remove the EMI protective cover from the connector. Step 3 Push the upper module latches up and the lower module latches down, and then slide the switch and module together.
Cisco IE 3000 Switch Getting Started Guide Push in the upper and lower module latches to secure the module to the switch. Step 5 If you are installing a second module, repeat Step 2 to Step 3, but secure the second module to the right side of the first module. 202336 Step 4 Running Express Setup When you first set up the switch, you should use Express Setup to enter the initial IP information. Doing this enables the switch to connect to local routers and the Internet.
Cisco IE 3000 Switch Getting Started Guide To run Express Setup: Step 1 Make sure that nothing is connected to the switch. Step 2 201873 During Express Setup, the switch acts as a DHCP server. If your PC has a static IP address, change your PC settings before you begin to temporarily use DHCP. Connect power to the switch. See the wiring instructions in the “Grounding the Switch” section on page 17 and the “Wiring the DC Power Source” section on page 18.
Cisco IE 3000 Switch Getting Started Guide Step 6 Connect a Category 5 Ethernet cable (not provided) from the blinking switch port to the Ethernet port on your PC. 1 201879 The port LEDs on your PC and the switch blink green while the switch configures the connection. Step 7 When the Setup LED turns solid green, start a browser session on the PC. Step 8 The Express Setup window automatically appears.
Cisco IE 3000 Switch Getting Started Guide Step 9 Enter the network settings. All entries must be in English letters and Arabic numbers. • Management Interface (VLAN): We recommend using the default, VLAN 1. The management VLAN establishes an IP connection to the switch. • IP Assignment Mode: We recommend using the default, Static, which means that the switch always has the IP address that you assign.
Cisco IE 3000 Switch Getting Started Guide Refreshing the PC IP Address After you complete Express Setup, you should refresh the PC IP address: • For a dynamically assigned IP address, disconnect the PC from the switch, and reconnect the PC to the network. The network DHCP server assigns a new IP address to the PC. • For a statically assigned IP address, change it to the previously configured IP address.
Cisco IE 3000 Switch Getting Started Guide 3. Use the device manager to perform basic switch configuration and monitoring. See the device manager online help for more information. 4. For more advanced configuration, download and run the Cisco Network Assistant, which is described in the next section. Downloading Cisco Network Assistant Cisco Network Assistant is a software program that you download from Cisco.com and run on your PC.
Cisco IE 3000 Switch Getting Started Guide Using the Switch Console Port: Follow these steps: 1. Connect the supplied RJ-45-to-DB-9 adapter cable (console cable) to the standard 9-pin serial port on the PC. Connect the other end of the cable to the console port on the switch. 2. Start a terminal-emulation program on the PC. 3. Configure the PC terminal emulation software for 9600 bits per second, 8 data bits, no parity, 1 stop bit, and no flow control.
Cisco IE 3000 Switch Getting Started Guide • Attaching the Power and Relay Connector, page 20 • Optional Procedures, page 21 Equipment That You Supply Obtain these necessary tools and equipment: • Ratcheting torque flathead screwdriver that exerts up to 15-inch pound (in-lb) of pressure • Ring terminal lug (such as Thomas & Bett part number 10RC6 or equivalent) • Crimping tool (such as Thomas & Bett part number WT2000, ERG-2001, or equivalent) • 10- to 12-gauge copper ground wire (such as Belden
Cisco IE 3000 Switch Getting Started Guide • Airflow around the switch and through the vents is unrestricted. To prevent the switch from overheating, these must be the minimum clearances: – Top and bottom: 4.13 in. (105 mm) – Left and right: 3.54 in. (90 mm) – Front: 2.56 in. (65 mm) • Note Temperature surrounding the unit does not exceed 140°F (60°C), the maximum ambient temperature of the switch.
Cisco IE 3000 Switch Getting Started Guide Warning This unit is intended for installation in restricted access areas. A restricted access area can be accessed only through the use of a special tool, lock and key, or other means of security. Statement 1017 Warning This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor.
Cisco IE 3000 Switch Getting Started Guide Warning When used in a Class I, Division 2, hazardous location, this equipment must be mounted in a suitable enclosure with proper wiring method, for all power, input and output wiring, that complies with the governing electrical codes and in accordance with the authority having jurisdiction over Class I, Division 2 installations. Statement 1066 Warning To prevent airflow restriction, allow clearance around the ventilation openings to be at least: 4.13 in. (10.
Cisco IE 3000 Switch Getting Started Guide Mounting the Switch to a DIN Rail or to the Rack Adapter Follow these steps to mount the switch on a DIN rail or in a rack. Step 1 If you are mounting the switch in a rack, first secure the Cisco IE 3000 rack adapter to the rack. 202337 If mounting on a DIN rail, omit this step. Insert a flat-head screwdriver in the space next to the tab, and turn the screw driver to release the latch and push it out.
Cisco IE 3000 Switch Getting Started Guide Position the rear panel of the switch directly in front of the DIN rail, making sure that the DIN rail fits in the space between the two latches. DIN rail 202339 Step 4 Step 5 Push the DIN rail latches in after the switch is over the DIN rail to secure the switch to the rail. You hear a click when the latches are completely locked. Step 6 Connect power to the switch.
Cisco IE 3000 Switch Getting Started Guide Insert the ground wire into the ring terminal lug, and using a crimping tool, crimp the ring terminal to the wire. Step 4 Slide the ground screw from Step 1 through the ring terminal. Step 5 Insert the ground screw into the ground-screw opening on the front panel. Step 6 Use a ratcheting torque screwdriver to tighten the ground screw and ring terminal lug to the switch front panel to 8.5 in-lb, the maximum recommended torque.
Cisco IE 3000 Switch Getting Started Guide Step 1 Warning This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 5A. Statement 1005 Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030 Locate the power and relay connector. 201815 V RT A A Identify the positive and return DC power connections on the connector.
Cisco IE 3000 Switch Getting Started Guide Step 7 Connect the other end of the positive wire (the one connected to V) to the positive terminal on the DC power source, and connect the other end of the return wire (the one connected to RT) to the return terminal on the DC power source. Step 8 When you are testing the switch, one power connection is sufficient. If you are installing the switch and are using a second power source, repeat Step 3 through Step 7 using a second power and relay connector.
Cisco IE 3000 Switch Getting Started Guide Optionally, insert a second power and relay connector into the Pwr B receptacle on the switch front panel. Step 4 Use a flathead screwdriver to tighten the captive screws on the sides of the second power and relay connector. V RT A Step 3 A V RT A 202333 A Optional Procedures For detailed instructions on these procedures, see the Cisco IE 3000 Switch Hardware Installation Guide on Cisco.com.
Cisco IE 3000 Switch Getting Started Guide Connecting to 10/100 and 10/100/1000 Ports Follow these steps: When you connect these switches to any Ethernet-enabled communication devices, insert a straight-through twisted four-pair, Category 5 cable in a switch 10/100 or 10/100/1000 port. Use a twisted four-pair, Category 5 cable when you connect to other switches, hubs, or repeaters. 10/100/1000 10/100 202325 Step 1 2 Step 2 Insert the other cable end into an RJ-45 connector on the other device.
Cisco IE 3000 Switch Getting Started Guide Installing SFP Modules and Connecting to Ports Follow these steps: Grasp the module on the sides, and insert it into the switch slot until you feel the connector snap into place. Step 2 Insert an appropriate cable into the module port. Step 3 Insert the other cable end into the other device. 202327 202326 Step 1 For a list of supported modules, see the release notes on Cisco.com.
Cisco IE 3000 Switch Getting Started Guide Connecting to Dual-Purpose Ports Only one port on a dual-purpose port can be active at a time. If both ports are connected, the SFP module port has priority. Follow these steps: Step 1 Insert either an RJ-45 connector to the 10/100/1000 port (see the “Connecting to 10/100 and 10/100/1000 Ports” section on page 22), or install an SFP module into the SFP module slot, and connect a cable to the SFP module port.
Cisco IE 3000 Switch Getting Started Guide In Case of Difficulty See these sections if you have difficulty setting up your switch: • Troubleshooting Express Setup, page 25 • Resetting the Switch, page 26 • Accessing Online Help, page 27 • For More Information, page 27 Troubleshooting Express Setup Help with the initial switch configuration is provided here. For additional assistance, see the online documentation at Cisco.com.
Cisco IE 3000 Switch Getting Started Guide Checklist Recommendation Did you have a wireless client running on your PC when you connected to the switch port? If yes, disconnect the cable from the switch port, disable the wireless client, press the Express Setup button, and reconnect the cable to the blinking Ethernet port. Do you need to change the switch IP Go to the Configure > Express Setup device manager screen to address after you have already change the switch IP address.
Cisco IE 3000 Switch Getting Started Guide Accessing Online Help First look for a solution to your problem in the troubleshooting section of the switch hardware installation guide or the switch software configuration guide on Cisco.com. You can also access the Cisco Technical Support and Documentation website for a list of known hardware problems and extensive troubleshooting documentation. For More Information For more information about the switch, see these documents on Cisco.
Cisco IE 3000 Switch Getting Started Guide Obtaining Documentation and Submitting a Service Request For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at: http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.
Cisco IE 3000 Switch Getting Started Guide Note 3. You must have Adobe Acrobat Reader to view and print PDF files. You can download the reader from Adobe’s website: http://www.adobe.com To read translated and localized warranty information about your product, follow these steps: a. Enter this part number in the Warranty Document Number field: 78-10747-01C0 b. Select the language in which you would like to view the document. c. Click Go. The Cisco warranty page appears. d.
Cisco IE 3000 Switch Getting Started Guide To Receive a Return Materials Authorization (RMA) Number Contact the company from whom you purchased the product. If you purchased the product directly from Cisco, contact your Cisco Sales and Service Representative. Complete the information below, and keep it for reference.
Cisco IE 3000 Switch Getting Started Guide Cisco IE 3000 Switch Getting Started Guide OL-16234-01 31
Cisco IE 3000 Switch Getting Started Guide CCDE, CCENT, Cisco Eos, Cisco Lumin, Cisco StadiumVision, the Cisco logo, DCE, and Welcome to the Human Network are trademarks; Changing the Way We Work, Live, Play, and Learn is a service mark; and Access Registrar, Aironet, AsyncOS, Bringing the Meeting To You, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, CCVP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco U
