Cisco IOS Voice, Video, and Fax Commands: R Through Sh This chapter presents the commands to configure and maintain Cisco IOS voice, video, and fax applications. The commands are presented in alphabetical order beginning with R. Some commands required for configuring voice, video, and fax may be found in other Cisco IOS command references. Use the command reference master index or search online to find these commands.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh register e164 register e164 To configure a gateway to register or deregister (remove the registration for) a fully qualified plain old telephone service (POTS) dial-peer E.164 address with a gatekeeper, use the register e164 command in dial-peer configuration mode. To deregister an E.164 address, use the no form of this command. register e164 no register e164 Syntax Description This command has no keywords or arguments. Defaults No E.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh register e164 The following commands deregister an address with the gatekeeper: dial-peer voice 111 pots no register e164 The following example shows that you must have a connection to a gatekeeper and define a unique E.164 address before you can register an address: dial-peer voice 222 pots port 1/0/0 destination 919555.... register e164 ERROR-register-e164:Dial-peer destination-pattern is not a full E.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh registered-caller ring registered-caller ring To configure the Nariwake service registered caller ring cadence, use the registered-caller ring command in dial-peer configuration mode. registered-caller ring cadence Syntax Description cadence Defaults The default Nariwake service registered caller ring cadence is ring 1. Command Modes Dial-peer configuration Command History Release Modification 12.1.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh req-qos req-qos To specify the desired quality of service to be used in reaching a specified dial peer, use the req-qos command in dial-peer configuration mode. To restore the default value for this command, use the no form of this command. req-qos {best-effort | controlled-load | guaranteed-delay} no req-qos Syntax Description best-effort Indicates that Resource Reservation Protocol (RSVP) makes no bandwidth reservation.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh reset reset To reset a set of digital signal processors (DSPs), use the reset command in global configuration mode. reset number Syntax Description number Defaults No default behavior or values. Command Modes Global configuration Command History 12.0(5)XE This command was introduced on the Cisco 7200 series routers. 12.0(7)T This command was integrated into the Cisco IOS Release 12.0(7)T. Examples Specifies the number of DSPs to be reset.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh resource threshold resource threshold To configure a gateway to report H.323 resource availability to the its gatekeeper, use the resource threshold command in gateway configuration mode. To disable gateway resource-level reporting, use the no form of this command.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh resource threshold When any monitored H.323 resources exceed the threshold level defined by the high parameter, the gateway sends an RAI message to the gatekeeper with the AlmostOutOfResources field flagged. This message reports high resource usage. When all gateway H.323 resources drop below the level defined by the low parameter, the gateway sends the RAI message to the gatekeeper with the AlmostOutOfResources field cleared.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh response-timeout response-timeout To configure the maximum time to wait for a response from a server, use the response-timeout command in settlement configuration mode. To restore the default value of this command, use the no form of this command. response-timeout number no response-timeout number Syntax Description number Defaults The default response timeout is one (1) second.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh response-timeout Command Description session-timeout Sets the interval for closing the connection when there is no input or output traffic. settlement Enters settlement mode and specifies the attributes specific to a settlement provider. show settlement Displays the configuration for all settlement server transactions. shutdown/no shutdown Deactivates the settlement provider/activates the settlement provider.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh retry-delay retry-delay To set the time between attempts to connect with the settlement provider, use the retry-delay command in settlement configuration mode. To restore the default value, use the no form of this command. retry-delay number no retry-delay Syntax Description number Defaults The default retry delay is two seconds. Command Modes Settlement configuration Command History Release Modification 12.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh retry-delay Command Description session-timeout Sets the interval for closing the connection when there is no input or output traffic. settlement Enters settlement configuration mode and specifies the attributes specific to a settlement provider. show settlement Displays the configuration for all settlement server transactions. shutdown/no shutdown Deactivates the settlement provider/activates the settlement provider.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh retry-limit retry-limit To set the maximum number of attempts to connect to the provider, use the retry-limit command in settlement configuration mode. To restore the default value, use the no form of this command. retry-limit number no retry-limit number Syntax Description number Defaults The default retry limit is one (1) retry. Command Modes Settlement configuration Command History Release Modification 12.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh retry-limit Command Description session-timeout Sets the length of interval for closing the connection when there is no input or output traffic. settlement Enters settlement mode and specifies the attributes specific to a settlement provider. show settlement Displays the configuration for all settlement server transactions. shutdown Brings up the settlement provider. type Configures an SAA-RTR operation type.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh retry (SIP user-agent) retry (SIP user-agent) To configure the number of retry attempts for Session Initiation Protocol (SIP) messages, use the retry command in SIP user-agent configuration mode. To reset this command to the default value, use the no form of this command.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh ring ring To set up a distinctive ring for your connected telephones, fax machines, or modems, use the ring command in interface configuration mode. To disable the specified distinctive ring, use the no form of this command. ring cadence-number no ring cadence-number Syntax Description cadence-number Number from 0 through 2: • Type 0 is a primary ringing cadence—default ringing cadence for the country your router is in.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh ring Related Commands Command Description destination-pattern Specifies either the prefix, the full E.164 telephone number, or an ISDN directory number (depending on the dial plan) to be used for a dial peer. dial-peer voice Enters dial-peer configuration mode, defines the type of dial peer, and defines the tag number associated with a dial peer. no call-waiting Disables call waiting.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh ring cadence ring cadence To specify the ring cadence for a Foreign Exchange Station (FXS) voice port, use the ring cadence command in voice-port configuration mode. To restore the default value, use the no form of this command. ring cadence {pattern-number | define pulse interval} no ring cadence Syntax Description pattern-number Predefined ring cadence patterns. Each pattern specifies a ring-pulse time and a ring-interval time.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh ring cadence Command Modes Voice-port configuration Command History Release Modification 11.3(1)MA This command was introduced on the Cisco MC3810 multiservice concentrator. 12.0(7)XK This command was first supported on the Cisco 2600 and 3600 series routers, and the patternXX keyword was introduced. 12.1(2)T This command was integrated into the 12.1(2)T release.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh ring frequency ring frequency To specify the ring frequency for a specified Foreign Exchange Station (FXS) voice port, use the ring frequency command in voice-port configuration mode. To restore the default value, use the no form of this command. ring frequency number no ring frequency number Syntax Description number Defaults 25 Hz on the Cisco 3600 series routers and 20 Hz on the Cisco MC3810 multiservice concentrators.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh ring frequency Related Commands Command Description ring cadence Specifies the ring cadence for an FXS voice port on the Cisco MC3810 multiservice concentrator. ring number Specifies the number of rings for a specified FXO voice port.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh ring number ring number To specify the number of rings for a specified Foreign Exchange Office (FXO) voice port, use the ring number command in voice-port configuration mode. To restore the default value, use the no form of this command. ring number number no ring number number Syntax Description number Defaults One ring Command Modes Voice-port configuration Command History Release Modification 11.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh ring number Related Commands Command Description ring frequency Specifies the ring frequency for a specified FXS voice port.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh roaming (dial-peer) roaming (dial-peer) To enable the roaming capability for the dial peer, use the roaming command in dial-peer configuration mode. To disable the roaming capability, use the no form of this command. roaming no roaming Syntax Description This command has no arguments or keywords. Defaults No roaming Command Modes Dial-peer configuration Command History Release Modification 12.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh roaming (settlement) roaming (settlement) To enable the roaming capability for a settlement provider, use the roaming command in settlement configuration mode. To disable the roaming capability, use the no form of this command. roaming no roaming Syntax Description This command has no arguments or keywords. Defaults No roaming Command Modes Settlement configuration Command History Release Modification 12.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh rtsp client session history duration rtsp client session history duration To specify how long to keep Real Time Streaming Protocol (RTSP) session history records in memory, use the rtsp client session history duration command in global configuration mode. To set the value to the default, use the no form of this command.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh rtsp client session history records rtsp client session history records To configure the number of records to keep in the RTSP client session history, use the rtsp client session history records command in global configuration mode. To set the value to the default, use the no form of this command.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh rule rule To apply a translation rule to a calling party number or a called party number for both incoming and outgoing calls, use the rule command in translation-rule configuration mode. To remove the translation rule, use the no form of this command.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh rule Release Modification 12.1(1)T This command was first supported on the T train for Voice over IP on the following platforms: Cisco 1750 routers, Cisco 2600 and 3600 series routers, Cisco AS5300 universal access servers, Cisco 7200 series routers, and Cisco 7500 series routers. 12.1(2)T This command was first supported for Voice over IP on the Cisco MC3810 multiservice concentrator.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh security security To enable authentication and authorization on a gatekeeper, use the security command in gatekeeper configuration mode. To disable security, use the no form of this command.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh security A RADIUS/TACACS+ server and encryption key must have been configured in Cisco IOS software for security to work. Only the first alias of the proper type will be identified. If no alias of the proper type is found, the registration will be rejected. This command does not allow you to define the password mechanism unless the security type (h323-id or e164 or any) has been defined.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh sequence-numbers sequence-numbers To enable the generation of sequence numbers in each frame generated by the digital signal processor (DSP) for Voice over Frame Relay applications, use the sequence-numbers command in dial-peer configuration mode. To disable the generation of sequence numbers, use the no form of this command. sequence-numbers no sequence-numbers Syntax Description This command has no arguments or keywords.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh sequence-numbers Related Commands Command Description called-number (dial-peer) Enables an incoming VoFR call leg to get bridged to the correct POTS call leg when using a static FRF.11 trunk connection. codec (dial-peer) Specifies the voice coder rate of speech for a Voice over Frame Relay dial peer. cptone Specifies a regional analog voice interface-related tone, ring, and cadence setting.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh server (RLM) server (RLM) To identify an RLM server, use the server RLM configuration command. To remove the identification, use the no form of this command server name-tag no server name-tag Syntax Description name-tag Defaults Disabled Command Modes RLM configuration Command History Release Modification 11.3(7) This command was introduced.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh server (RLM) Related Commands Command Description clear interface Resets the hardware logic on an interface. clear rlm group Clears all RLM group time stamps to zero. interface Defines the IP addresses of the server, configures an interface type, and enters interface configuration mode. link (RLM) Specifies the link preference. protocol rlm port Reconfigures the port number for the basic RLM connection for the whole rlm-group.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh server registration-port server registration-port To configure the listener port for the server to establish a connection with the gatekeeper, use the server registration-port command in gatekeeper configuration mode. To force the gatekeeper to close the listening socket so that no more new registration takes place, use the no form of this command.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh server trigger server trigger To configure a static server trigger for external applications, use the server trigger command in gatekeeper configuration mode. To remove a single statically configured trigger entry, use the no form of this command. To remove every static trigger you configured if you want to delete them all, use the all keyword.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh server trigger In LCF submode, enter the following syntax: server trigger lcf gkid priority server-id server-ipaddress server-port In LRJ submode, enter the following syntax: server trigger lrj gkid priority server-id server-ipaddress server-port In LRQ submode, enter the following syntax: server trigger lrq gkid priority server-id server-ipaddress server-port In RRQ submode, enter the following syntax: server trigger rrq gkid priority server-id ser
Cisco IOS Voice, Video, and Fax Commands: R Through Sh server trigger The remote-ext-address argument is under the LCF trigger submode and has the following options: remote-ext-address e164 word Configure remote extension addresses, with the following options: Configure an E.164 pattern. When configuring the e164 address option, the email-id option, or the h323-id option above, the E.164 address can end in a trailing ‘., ‘s, or ‘*’.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh session session To associate a transport session with a specified session-group, use the session group command in backhaul session manager configuration mode. It is assumed that the server is located on a remote machine. To delete the session, use the no form of this command.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh session protocol session protocol To specify a session protocol for calls between the local and remote routers using the packet network, use the session protocol command in dial-peer configuration mode. To reset the default value for this command, use the no form of this command. session protocol {cisco | sipv2 | aal2-trunk | smtp} no session protocol Syntax Description cisco Configure the dial peer to use proprietary Cisco VoIP session protocol.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh session protocol The following example selects AAL2 trunking as the session protocol on a Cisco MC3810 multiservice concentrator: dial-peer voice 10 voatm session protocol aal2-trunk The following example selects Cisco Session Protocol as the session protocol on a Cisco 3600 series router: dial-peer voice 20 voip session protocol cisco The following example selects SMTP as the session protocol: dial-peer voice 10 mmoip session protocol smtp Related
Cisco IOS Voice, Video, and Fax Commands: R Through Sh session protocol (Voice over Frame Relay) session protocol (Voice over Frame Relay) To establish a Voice over Frame Relay protocol for calls between the local and remote routers via the packet network, use the session protocol command in dial-peer configuration mode. To reset the default value, use the no form of this command.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh session protocol (Voice over Frame Relay) Related Commands Command Description called-number (dial-peer) Enables an incoming VoFR call leg to get bridged to the correct POTS call leg when using a static FRF.11 trunk connection. codec (dial-peer) Specifies the voice coder rate of speech for a Voice over Frame Relay dial peer. cptone Specifies a regional analog voice interface-related tone, ring, and cadence setting.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh session protocol aal2 session protocol aal2 To enter the voice-service-session configuration mode and specify AAL2 trunking on a Cisco MC3810 multiservice concentrator, use the session protocol aal2 command in voice-service configuration mode. session protocol aal2 Syntax Description This command has no keywords or arguments. Defaults There is no default setting for this command.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh session protocol multicast session protocol multicast To set the session protocol as multicast, use the session protocol multicast command dial-peer configuration mode. To negate this command and return to the Cisco default session protocol, use the no version of this command. session protocol multicast no session protocol multicast Syntax Description There are no keywords or arguments.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh session target (VoATM) session target (VoATM) To specify a network-specific address for a specified VoATM dial peer, use the session target command in dial-peer configuration mode. To restore default values for this parameter, use the no form of this command.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh session target (VoATM) Command History Usage Guidelines Release Modification 11.3(1)T This command was introduced. 11.3(1)MA Support was added for VoATM, VoHDLC, and POTS dial peers on the Cisco MC3810 multiservice concentrator. 12.0(7)XK Support was added for VoATM dial peers on the Cisco 3600 series routers. Support for VoHDLC on the Cisco MC3810 multiservice concentrator was removed. 12.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh session target (VoATM) Related Commands Command Description called-number Enables an incoming VoFR call leg to be bridged to the correct POTS call leg. codec (dial-peer) Specifies the voice coder rate of speech for a dial peer. cptone Specifies a regional tone, ring, and cadence setting for an analog voice port. destination-pattern Specifies either the prefix or the full E.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh session target (VoFR) session target (VoFR) To specify a network-specific address for a specified VoFR dial peer, use the session target command in dial-peer configuration mode. To restore default values for this parameter, use the no form of this command.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh session target (VoFR) Command History Usage Guidelines Release Modification 11.3(1)T This command was introduced. 11.3(1)MA Support was added for VoFR, VoHDLC, and POTS dial peers on the Cisco MC3810 multiservice concentrator. 12.0(3)XG Support was added for VoFR dial peers on the Cisco 2600 series and 3600 series routers. The cid option was added. 12.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh session target (VoFR) Related Commands Command Description called-number Enables an incoming VoFR call leg to be bridged to the correct POTS call leg. codec (dial-peer) Specifies the voice coder rate of speech for a dial peer. cptone Specifies a regional tone, ring, and cadence setting for an analog voice port. destination-pattern Specifies either the prefix or the full E.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh session target (VoIP) session target (VoIP) To specify a network-specific address for a specified VoIP dial peer, use the session target command in dial-peer configuration mode. To restore default values for this parameter, use the no form of this command. Cisco 2600 and Cisco 3600 Series Routers and Cisco MC8310 Multiservice Concentrator Voice over IP Dial Peers session target {ipv4:destination-address | dns:[$s$. | $d$. | $e$. | $u$.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh session target (VoIP) loopback:uncompresse d Indicates that all voice data will be looped-back in uncompressed mode to the source. This is applicable for POTS peers. ras Indicates that the registration, admission, and status (RAS) signaling function protocol is being used, meaning that a gatekeeper will be consulted to translate the E.164 address into an IP address.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh session target (VoIP) session target dns:voice_router.cisco.com The following example configures a session target using DNS, with the optional $u$. wildcard. In this example, the destination pattern has been configured to allow for any four-digit extension, beginning with the numbers 1310222. The optional wildcard $u$.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh session transport session transport To configure the VoIP dial peer to use TCP or User Datagram Protocol (UDP) as the underlying transport layer protocol for Session Initiation Protocol (SIP) messages, use the session transport command in dial-peer configuration mode. To reset the value to the default, use the no form of this command.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh set set To create a fault-tolerant or non-fault-tolerant session-set with the client or server option, use the set command in backhaul session manager configuration mode. To delete the set, use the no form of this command. set set-name { client | server } { ft | nft } no set set-name { client | server } { ft | nft } Syntax Description set-name Session-set name. client Client option. The session-set should only be configured as client for backhaul.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh settle-call settle-call To force a call to be authorized with a settlement server that uses the address resolution method specified in the session target type command, use the settle-call command in dial-peer configuration mode. To make sure that no authorization will be performed by a settlement server, use the no form of this command.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh settle-call Related Commands Command Description session target Specifies a network-specific address for a specified dial peer.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh settlement settlement To enter settlement configuration mode and specify the attributes specific to a settlement provider, use the settlement command in global configuration mode. To disable the settlement provider, use the no form of this command. settlement provider-number no settlement provider-number Syntax Description provider-number Defaults 0 Command Modes Global configuration Command History Release Modification 12.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh settlement Command Description session-timeout Sets the interval for closing the connection when there is no input or output traffic. show settlement Displays the configuration for all settlement server transactions. shutdown Brings up the settlement provider. type Configures an SAA-RTR operation type.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh settlement roam-pattern settlement roam-pattern To configure a pattern that must be matched to determine if a user is roaming, use the settlement roam-pattern command in global configuration mode. To delete a particular pattern, use the no form of this command.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh sgcp sgcp To start and allocate resources for the Simple Gateway Control Protocol (SGCP) daemon, use the sgcp command in global configuration mode. To terminate all calls, release all allocated resources, and kill the SGCP daemon, use the no form of this command. sgcp no sgcp Syntax Description This command has no arguments or keywords. Defaults The SGCP daemon is not enabled.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh sgcp Related Commands Command Description sgcp call-agent Defines the IP address of the default SGCP call agent. sgcp graceful-shutdown Gracefully terminates all SGCP activity. sgcp max-waiting-delay Sets the SGCP maximum waiting delay to prevent restart avalanches. sgcp modem passthru Enables SGCP modem or fax pass-through. sgcp quarantine-buffer disable Disables the SGCP quarantine buffer.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh sgcp call-agent sgcp call-agent To define the IP address of the default Simple Gateway Control Protocol (SGCP) call agent in the router configuration file, use the sgcp call-agent command in global configuration mode. To remove the IP address of the default SGCP call agent from the router configuration, use the no form of this command.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh sgcp call-agent Related Commands Command Description sgcp Starts and allocates resources for the SGCP daemon. sgcp graceful-shutdown Gracefully terminates all SGCP activity. sgcp max-waiting-delay Sets the SGCP maximum waiting delay to prevent restart avalanches. sgcp modem passthru Enables SGCP modem or fax pass-through. sgcp quarantine-buffer disable Disables the SGCP quarantine buffer.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh sgcp graceful-shutdown sgcp graceful-shutdown To block all new calls and gracefully terminate all existing calls (wait for the caller to end the call), use the sgcp graceful-shutdown command in global configuration mode. To unblock all calls and allow new calls to go through, use the no form of this command. sgcp graceful-shutdown no sgcp graceful-shutdown Syntax Description This command has no arguments or keywords.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh sgcp graceful-shutdown Command Description sgcp quarantine-buffer disable Disables the SGCP quarantine buffer. sgcp request retries Specifies the number of times to retry sending “notify” and “delete” messages to the SGCP call agent. sgcp request timeout Specifies how long the system should wait for a response to a request.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh sgcp max-waiting-delay sgcp max-waiting-delay To set the Simple Gateway Control Protocol (SGCP) maximum waiting delay to prevent restart avalanches, use the sgcp max-waiting-delay command in global configuration mode. To restore the default value, use the no form of this command.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh sgcp max-waiting-delay Command Description sgcp restart Triggers the router to send an RSIP message to the SGCP call agent indicating that the T1 controller is up or down so that the call agent can synchronize with the T1 controller. sgcp retransmit timer Configures the SGCP retransmission timer to use a random algorithm method. sgcp timer Configures how the gateway detects the RTP stream host.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh sgcp modem passthru sgcp modem passthru To enable Simple Gateway Control Protocol (SGCP) modem or fax pass-through, use the sgcp modem passthru command in global configuration mode. To disable SGCP modem or fax pass-through, use the no form of this command. sgcp modem passthru {ca | cisco | nse} no sgcp modem passthru {ca | cisco | nse} Syntax Description ca Uses the call agent controlled modem upspeed method violation message.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh sgcp modem passthru sgcp modem passthru nse sgcp tse payload 110 Related Commands Command Description sgcp Starts and allocates resources for the SGCP daemon. sgcp call-agent Defines the IP address of the default SGCP call agent. sgcp graceful-shutdown Gracefully terminates all SGCP activity. sgcp max-waiting-delay Sets the SGCP maximum waiting delay to prevent restart avalanches.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh sgcp quarantine-buffer disable sgcp quarantine-buffer disable To disable the Simple Gateway Control Protocol (SGCP) quarantine buffer, use the sgcp quarantine-buffer disable command in global configuration mode. To reenable the SGCP quarantine buffer, use the no form of this command. sgcp quarantine-buffer disable no sgcp quarantine-buffer disable Syntax Description This command has no arguments or keywords.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh sgcp quarantine-buffer disable Command Description sgcp restart Triggers the router to send an RSIP message to the SGCP call agent indicating that the T1 controller is up or down so that the call agent can synchronize with the T1 controller. sgcp retransmit timer Configures the SGCP retransmission timer to use a random algorithm method. sgcp timer Configures how the gateway detects the RTP stream host.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh sgcp request retries sgcp request retries To specify the number of times to retry sending “notify” and “delete” messages to the Simple Gateway Control Protocol (SGCP) call agent, use the sgcp request retries command in global configuration mode. To restore the default value, use the no form of this command.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh sgcp request retries Related Commands Command Description sgcp Starts and allocates resources for the SGCP daemon. sgcp call-agent Defines the IP address of the default SGCP call agent. sgcp graceful-shutdown Gracefully terminates all SGCP activity. sgcp max-waiting-delay Sets the SGCP maximum waiting delay to prevent restart avalanches. sgcp modem passthru Enables SGCP modem or fax pass-through.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh sgcp request timeout sgcp request timeout To specify how long the system should wait for a response to a request, use the sgcp request timeout command in global configuration mode. To restore the default value, use the no form of this command. sgcp request timeout timeout no sgcp request timeout Syntax Description timeout Defaults 500 milliseconds Command Modes Global configuration Command History Release Modification 12.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh sgcp request timeout Command Description sgcp request retries Specifies the number of times to retry sending “notify” and “delete” messages to the SGCP call agent. sgcp restart Triggers the router to send an RSIP message to the SGCP call agent indicating that the T1 controller is up or down so that the call agent can synchronize with the T1 controller.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh sgcp restart sgcp restart To trigger the router to send a Restart in Progress (RSIP) message to the Simple Gateway Control Protocol (SGCP) call agent indicating that the T1 controller is up or down so that the call agent can synchronize with the T1 controller, use the sgcp restart command in global configuration mode. To restore the default value, use the no form of this command.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh sgcp restart Related Commands Command Description sgcp Starts and allocates resources for the SGCP daemon. sgcp call-agent Defines the IP address of the default SGCP call agent. sgcp graceful-shutdown Gracefully terminates all SGCP activity. sgcp max-waiting-delay Sets the SGCP maximum waiting delay to prevent restart avalanches. sgcp modem passthru Enables SGCP modem or fax pass-through.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh sgcp retransmit timer sgcp retransmit timer To configure the Simple Gateway Control Protocol (SGCP) retransmission timer to use a random algorithm, use the sgcp retransmit timer command in global configuration mode. To restore the default value, use the no form of this command. sgcp retransmit timer {random} no sgcp retransmit timer {random} Syntax Description random Defaults The SGCP retransmission timer does not use the random algorithm.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh sgcp retransmit timer Related Commands Command Description sgcp Starts and allocates resources for the SGCP daemon. sgcp call-agent Defines the IP address of the default SGCP call agent. sgcp graceful-shutdown Gracefully terminates all SGCP activity. sgcp max-waiting-delay Sets the SGCP maximum waiting delay to prevent restart avalanches. sgcp modem passthru Enables SGCP modem or fax pass-through.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh sgcp timer sgcp timer To configure how the gateway detects the Real-Time Transport Protocol (RTP) stream lost, use the sgcp timer command in global configuration mode. To restore the default value, use the no form of this command.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh sgcp timer Related Commands Command Description sgcp Starts and allocates resources for the SGCP daemon. sgcp call-agent Defines the IP address of the default SGCP call agent. sgcp graceful-shutdown Gracefully terminates all SGCP activity. sgcp max-waiting-delay Sets the SGCP maximum waiting delay to prevent restart avalanches. sgcp modem passthru Enables SGCP modem or fax pass-through.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh sgcp tse payload sgcp tse payload To enable Inband Telephony Signaling Events (TSE) for fax and modem operation, use the sgcp tse payload command in global configuration mode. To restore the default value, use the no form of this command. sgcp tse payload type no sgcp tse payload type Syntax Description type Defaults Zero (0) Command Modes Global configuration Command History Release Modification 12.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh sgcp tse payload Command Description sgcp max-waiting-delay Sets the SGCP maximum waiting delay to prevent restart avalanches. sgcp modem passthru Enables SGCP modem or fax pass-through. sgcp quarantine-buffer disable Disables the SGCP quarantine buffer. sgcp request retries Specifies the number of times to retry sending “notify” and “delete” messages to the SGCP call agent.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show aal2 profile show aal2 profile To display the ATM adaptation layer 2 (AAL2) profiles configured on the system, use the show aal2 profile command in privileged EXEC mode. show aal2 profile all | {itut profile-number | custom profile-number | atmf profile-number} Syntax Description all Displays International Telecommunication Union Telecommunication Standardization Sector (ITU-T), ATM Forum, and custom AAL2 profiles configured on the system.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show aal2 profile Printing all the Profiles in the system Profile Type: ITUT Profile Number: 1 SID Support: 0 Red enable: 1 Num entries: 1 Coding type: g711ulaw Packet length: 40 UUI min: 0 UUI max: 15 Profile Type: ITUT Profile Number: 2 SID Support: 1 Red enable: 1 Num entries: 1 Coding type: g711ulaw Packet length: 40 UUI min: 0 UUI max: 15 Profile Type: custom Profile Number: 100 SID Support: 1 Red enable: 1 Num entries: 2 Coding type: g711ulaw Pac
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show atm video-voice address show atm video-voice address To display the network service access point (NSAP) address for the ATM interface, enter the show atm video-voice address command in privileged EXEC mode. show atm video-voice address Syntax Description This command has no keywords or arguments. Defaults No default behavior or values. Command Modes Privileged EXEC Command History Release Modification 12.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show backhaul-session-manager group show backhaul-session-manager group To display status, statistics, or configuration information for all available session-groups, use the show backhaul-session-manager group command in privileged EXEC mode. show backhaul-session-manager group { status | stats | cfg } { all | name group-name } Syntax Description status Displays status information for session-groups. stats Displays statistics for session-groups.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show backhaul-session-manager group cumulative ack max retrans max out-of-sequence max auto-reset max :3 :2 :3 :5 The following displays the current status of all session-groups. This group named grp1 belongs to the set named set1. The Status will be either Group-OutOfService (no session in the group has been established) or Group-Inservice (at least one session in the group has been established).
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show backhaul-session-manager session show backhaul-session-manager session To display various information for about a session or sessions, use the show backhaul-session-manager session command in privileged EXEC mode. show backhaul-session-manager session { all | ip ip_address } Syntax Description all All available sessions. ip ip_address The IP address of the local or remote session. Defaults No default behavior or values.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show backhaul-session-manager session Transmit Failures (PDU Only) Due to Blocking (Not an Error) - Total:0, Since Last Reset:0 Due to causes other than Blocking - Total:0, Since Last Reset:0 Transmit Failures (NON-PDU Only) Due to Blocking(Not an Error) - Total:0, Since Last Reset:0 Due to causes other than Blocking - Total:0, Since Last Reset:0 RUDP statistics Open failures:0 Not ready failures:0 Conn Not Open failures:0 Send window full failures:0 R
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show backhaul-session-manager set show backhaul-session-manager set To display session-groups associated with a specified session-set or all session-sets, use the show backhaul-session-manager set command in privileged EXEC mode. show backhaul-session-manager set { all | name session-set-name } Syntax Description all All available session-sets. name session-set-name A specified session-set. Defaults No default behavior or values.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call active show call active To display active call information for voice calls or fax transmissions in progress, use the show call active command in user EXEC or privileged EXEC mode. show call active {voice | fax}[brief] Syntax Description voice Specifies that information be displayed for all active voice calls. fax Specifies that information be displayed for all active fax calls.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call active Examples The following is sample output from the show call active voice command: Router# show call active voice GENERIC: SetupTime=104443 ms Index=1 PeerAddress=50110 PeerSubAddress= PeerId=100 PeerIfIndex=104 LogicalIfIndex=10 ConnectTime=104964 CallDuration=00:02:43 CallState=4 CallOrigin=2 ChargedUnits=0 InfoType=2 TransmitPackets=15720 TransmitBytes=2362904 ReceivePackets=15670 ReceiveBytes=2737904 TELE: ConnectionId=[0x4B091A27 0
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call active SessionTarget=ipv4:1.14.82.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call active CallState=4 CallOrigin=2 ChargedUnits=0 InfoType=10 TransmitPackets=0 TransmitBytes=0 ReceivePackets=0 ReceiveBytes=41190 MMOIP: ConnectionId[0x37EC7F41 0xB0110001 0x0 0x35C34] RemoteIPAddress=0.0.0.0 SessionProtocol=SMTP SessionTarget= MessageId= AccountId= ImgEncodingType=MH ImgResolution=fine AcceptedMimeTypes=2 DiscardedMimeTypes=1 Notification=None GENERIC: SetupTime=23193 ms Index=1 PeerAddress=527....
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call active Tele : tx://ms noise: acom: i/o:/ dBm 1 : 22021hs.1 +2263 pid:0 Answer wook song active tx:0/0 rx:0/41190 IP 0.0.0.0 AcceptedMime:2 DiscardedMime:1 1 : 23193hs.1 +1091 pid:3469 Originate 527....
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call active Table 27 show call active Field Descriptions (continued) Field Description GapFillWithPrediction Duration of the voice signal played out with signal synthesized from parameters, or samples of data preceding in time, because voice data was lost or not received in time from the voice gateway for this call. Examples of such pullout are frame-eraser or frame-concealment strategies in G.729 and G.723.1 compression algorithms.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call active Table 27 Related Commands show call active Field Descriptions (continued) Field Description RoundTripDelay Voice packet round trip delay between the local and remote systems on the IP backbone for this call. SelectedQoS Selected RSVP quality of service (QoS) for this call. SessionProtocol Session protocol used for an Internet call between the local and remote routers through the IP backbone.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call application voice show call application voice To define the names of the audio files that the interactive voice response (IVR) script will play, the operation of the abort keys, the prompts that are used, and caller interaction, use the show call application voice command in EXEC mode. show call application voice [name | summary] Syntax Description name (Optional) The name of the desired IVR application.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call application voice and do nothing State get_account has 4 actions and 7 events Do Action IVR_ACT_PLAY. URL: flash:enter_account.au allowInt=1, pContent=0x60E4C564 Do Action IVR_ACT_ABORT_KEY. abortKey=* Do Action IVR_ACT_TERMINATION_KEY. terminationKey=# Do Action IVR_ACT_COLLECT_PATTERN. Pattern account is .
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call application voice State authenticate_fail has 1 actions and 2 events Do Action IVR_ACT_PLAY. URL: flash:auth_failed.au allowInt=0, pContent=0x0 If Event IVR_EV_DEFAULT goto state end If Event IVR_EV_CALL_DIGIT do nothing State place_fail has 1 actions and 2 events Do Action IVR_ACT_PLAY_FAILURE_TONE.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call application voice If Event IVR_EV_AAA_FAIL goto state authenticate_fail State collect_dest has 4 actions and 8 events Do Action IVR_ACT_PLAY. URL: flash:enter_destination.au allowInt=1, pContent=0x0 Do Action IVR_ACT_ABORT_KEY. abortKey=* Do Action IVR_ACT_TERMINATION_KEY. terminationKey=# Do Action IVR_ACT_COLLECT_DIALPLAN.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call fallback cache show call fallback cache To see the current Calculated Planning Impairment Factor (ICPIF) estimates for all IP addresses in cache, use the show call fallback cache command in EXEC mode. show call fallback cache [ip-address] Syntax Description ip-address Defaults This command is not configured by default. Command Modes EXEC Command History Release Modification 12.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call fallback cache Router# show call fallback cache 10.14.115.53 Probe ----1 IP Address ---------10.14.115.53 Codec ----g729r8 ICPIF ----0 Reject -----0 Accept -----2 1 active probes Related Commands Command Description show call fallback stats Displays the call fallback statistics.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call fallback config show call fallback config To display the call fallback configuration, use the show call fallback config command in EXEC mode. show call fallback config Syntax Description This command has no arguments or keywords. Defaults This command is not configured by default. Command Modes EXEC Command History Release Modification 12.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call fallback stats show call fallback stats To display the call fallback statistics, use the show call fallback stats command in EXEC mode. show call fallback stats Syntax Description This command has no arguments or keywords. Defaults This command is not configured by default. Command Modes EXEC Command History Release Modification 12.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call history show call history To display the call history table for voice calls or fax transmissions, use the show call history command in user EXEC or privileged EXEC mode. show call history {voice | fax}[last number | brief] Syntax Description voice Specifies that call history information be displayed for voice calls. fax Specifies that call history information be displayed for fax calls.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call history To display a truncated version of the call history table, use the brief keyword. When using the fax keyword, this command applies to both on-ramp and off-ramp store-and-forward fax functions.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call history Corrected packet-loss Events = 0 Last Buffer Drain/Fill Event = 373sec Time between Buffer Drain/Fills = Min 0sec Max 0sec GENERIC: SetupTime=104443 ms Index=2 PeerAddress=50110 PeerSubAddress= PeerId=100 PeerIfIndex=104 LogicalIfIndex=10 DisconnectCause=10 DisconnectText=normal call clearing.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call history DisconnectText=normal call clearing.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call history 2 : 5996450hs.25 +-1 +3802 pid:100 Answer 408 tx:0/0 rx:0/0 1F (T30 T1 EOM timeout) Telephony : tx:38020/38020/0ms g729r8 noise:0dBm acom:0dBm 2 : 5996752hs.26 +-1 +3500 pid:110 Originate uut1@linux2.allegro.com tx:0/0 rx:0/0 3F (The e-mail was not sent correctly. Remote SMTP server said: 354 ) IP 14.0.0.1 AcceptedMime:0 DiscardedMime:0 3 : 6447851hs.27 +1111 +3616 pid:310 Originate 576341.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call history Table 28 show call history Field Descriptions (continued) Field Description CallDuration Length of the call, in hours, minutes, and seconds, hh:mm:ss. CallOrigin Call origin: answer or originate. ChargedUnits Total number of charging units applying to this peer since system startup. The unit of measure for this field is hundredths of a second. CodecBytes Payload size in bytes for the codec used.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call history Table 28 show call history Field Descriptions (continued) Field Description Modem passthrough signaling method is nse Indicates that this is a modem pass-through call and named signaling events (NSEs)—also called telephone-events in RFC 2833—are used for signaling codec upspeed. The upspeed method is the method used to dynamically change the codec type and speed to meet network conditions.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call history Table 28 Related Commands show call history Field Descriptions (continued) Field Description VAD Specifies whether voice activation detection (VAD) was enabled for this call. VoiceTxDuration Duration of voice transmission from this peer to the voice gateway for this call. Derive the Voice Utilization Rate by dividing the VoiceTxDuration value by the TxDuration value.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call history video record show call history video record To display information about video calls, use the show call history video record command in privileged EXEC mode. show call history video record Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes Privileged EXEC Command History Release Modification 12.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call history voice record show call history voice record To display Call Detail Record (CDR) events in the call history table, use the show call history voice record command in privileged EXEC mode. show call history voice record Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes Privileged EXEC Command History Release Modification 12.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call history voice record Table 29 Related Commands show call history voice record Field Descriptions Field Description ConnectionID Global call identifier for this voice call. Media Medium over which the call is carried. If the call is carried over the (telephone) access side, the entry will be TELE. If the call is carried over the voice network side, the entry will be either ATM, FR (for Frame Relay), or HDLC.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call resource voice stats show call resource voice stats To display resource statistics for an H.323 gateway, use the show call resource voice stats command in privileged EXEC mode. show call resource voice stats Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes Privileged EXEC Command History Release Modification 12.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call resource voice stats Table 30 Related Commands show call resource voice stats Field Descriptions Statistic Definition Total channels Number of channels physically configured for the resource. Addressable channels Number of channels that can be used for a specific type of dialup service, such as H.323, which includes all the DS0 resources that have been associated with a voice plain old telephone service (POTS) dial plan profile.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call resource voice threshold show call resource voice threshold To display the threshold configuration settings and status for an H.323 gateway, use the show call resource voice threshold command in privileged EXEC mode. show call resource voice threshold Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes Privileged EXEC Command History Release Modification 12.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call rsvp-sync conf show call rsvp-sync conf To display the configuration settings for Resource Reservation Protocol (RSVP) synchronization, use the show call rsvp-sync conf command in privileged EXEC mode. show call rsvp-sync conf Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes Privileged EXEC Command History Release Modification 12.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call rsvp-sync conf Related Commands Command Description call rsvp-sync Enables synchronization between RSVP and the H.323 voice signaling protocol. call rsvp-sync resv-timer Sets the timer for RSVP reservation setup. debug call rsvp-sync events Displays the events that occur during RSVP synchronization. show call rsvp-sync stats Displays statistics for calls that attempted RSVP reservation.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call rsvp-sync stats show call rsvp-sync stats To display statistics for calls that attempted Resource Reservation Protocol (RSVP) reservation, use the show call rsvp-sync stats command in privileged EXEC mode. show call rsvp-sync stats Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes Privileged EXEC Command History Release Modification 12.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show call rsvp-sync stats Related Commands Command Description call rsvp-sync Enables synchronization between RSVP and the H.323 voice signaling protocol. call rsvp-sync resv-timer Sets the timer for RSVP reservation setup. debug call rsvp-sync events Displays the events that occur during RSVP synchronization. show call rsvp-sync conf Displays the RSVP synchronization configuration.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show cdapi show cdapi To display the Call Distributor Application Programming Interface (CDAPI), use the show cdapi command in privileged EXEC mode. show cdapi Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes Privileged EXEC Command History Release Modification 12.0(7)T This command was introduced on the Cisco AS5300 universal access server.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show cdapi Related Commands Command Description isdn protocol-emulate Configures the Layer 2 and Layer 3 port protocol of a BRI voice port or a PRI interface to emulate NT (network) or TE (user) functionality. isdn switch type Configures the Cisco AS5300 universal access server PRI interface to support Q.SIG signaling. pri-group nec-fusion Configures your NEC PBX to support FCCS.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show ces clock-select show ces clock-select To display the setting of the network clock for the specified port, use the show ces clock-select command in privileged EXEC mode. show ces slot/port clock-select Syntax Description slot Backplane slot number. /port Interface port number. The slash must be entered. Command Modes Privileged EXEC Command History Release Modification 12.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show connect show connect To display configuration information about drop-and-insert connections that have been configured on a router, enter the show connect command in privileged EXEC mode. show connect {all | elements | name | id | port {T1 | E1} slot/port}} Syntax Description all Displays a table of all configured connections. elements Displays registered hardware or software interworking elements.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show connect Examples The following examples show how the same tabular information appears when you enter different keywords: Router# show connect all ID Name Segment 1 Segment 2 State ======================================================================== 1 Test -T1 1/0 01 -T1 1/1 02 ADMIN UP 2 Test2 -T1 1/0 03 -T1 1/1 04 ADMIN UP Router# show connect id 1-2 ID Name Segment 1 Segment 2 State ==========================================================
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show controllers rs366 show controllers rs366 To display information about the RS-366 video interface on the video dialing module (VDM), use the show controllers rs366 command in privileged EXEC mode. show controllers rs366 slot port Syntax Description slot Slot location of the VDM module. On the Cisco MC3810 multiservice concentrator, this value is either 1 or 2. If you do not enter the correct location, the command is rejected.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show controllers rs366 Table 33 show controllers Field Descriptions (continued) Field Description ICSR Interrupt control and status register of the VDM. EXT Extended register of the VDM. T1 through T5 Timeouts 1 through 5 of the watchdog timer, in milliseconds. Dial string Most recently dialed number collected by the driver. 0xC at the end of the string indicates the EON (end of number) character.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show controllers timeslots show controllers timeslots To show the channel-associated signaling (CAS) and ISDN PRI state in detail, use the show controllers timeslots command in privileged EXEC mode. show controllers t1/e1 controller-number timeslots timeslot-range Syntax Description tl/e1 Specifies the type of interface. controller-number Specifies the controller number of CAS or ISDN PRI time slot. Range 0 through 7.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show controllers timeslots 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 cas cas cas cas cas cas cas cas cas cas cas cas unused unused unused - - maint maint maint maint maint maint maint maint maint maint maint maint static-bo static-bo static-bo static-bo static-bo static-bo static-bo static-bo static-bo dynamic-bo dynamic-bo dynamic-bo 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show controllers voice show controllers voice To display information about voice-related hardware, use the show controllers voice command in privileged EXEC mode. Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes Privileged EXEC Command History Release Modification 12.0(5)XQ This command was introduced on the Cisco 1750.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show controllers voice 0040: 0060: 0080: BBC8 7E48 3B34 3131 363D 4FDE C3B9 B3B1 B3B8 C2DB 533F 3833 3235 3B48 71CC BDB7 B4B5 B8BF CF67 483D 3836 383C 455B DAC6 BDB9 B9BB Rx Message 2: packet_length 100 0000: 0000 4AC8 0020: CF4F CD4E 0040: 5DE1 6E7C 0060: 5CDD 5BDC 0080: EB6F F16D channel_id 2 packet_id 0 5F08 9221 0000 0000 54DA D256 DB63 FCEE 5FDA 55D1 EC60 DC59 D655 D456 D85D 5BDE 61E9 6DF1 FF76 F16D EF79 F776 F5F5 73F0 process id 0x1 61F5 EF60
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show controllers voice 0040: 0060: 0080: BBC8 7E48 3B34 3131 363D 4FDE C3B9 B3B1 B3B8 C2DB 533F 3833 3235 3B48 71CC BDB7 B4B5 B8BF CF67 483D 3836 383C 455B DAC6 BDB9 B9BB Tx Message 4: packet_length 100 0000: 0000 4AC8 0020: CF4F CD4E 0040: 5DE1 6E7C 0060: 5CDD 5BDC 0080: EB6F F16D channel_id 1 packet_id 0 5F08 9221 0000 003C 54DA D256 DB63 FCEE 5FDA 55D1 EC60 DC59 D655 D456 D85D 5BDE 61E9 6DF1 FF76 F16D EF79 F776 F5F5 73F0 process id 0x1 61F5 EF60
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show controllers voice 0 drops, 0 no buffers, 0 input errors 0 input overruns 393976 bytes output, 3982 frames output, 0 output errors, 0 output underrun 0 unaligned frames Related Commands Command Description show dial-peer voice Displays configuration information and call statistics for dial peers. show interface dspfarm Displays hardware informatio,n including DRAM, SRAM, and the revision-level information on the line card.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show csm show csm To display the call switching module (CSM) statistics for a particular digital signal processor (DSP) channel or all DSP channels or for a specific modem or DSP channel, use the show csm command in privileged EXEC mode.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show csm Use the show csm voice command to display CSM statistics for a particular DSP channel. If the slot/dspm/dsp/dsp-channel or shelf/slot/port argument is specified, the CSM call statistics for calls using the identified DSP channel will be displayed. If no argument is specified, all CSM call statistics for all DSP channels will be displayed.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show csm Table 34 describes the significant fields shown in the display. Table 34 show csm voice Field Descriptions Field Description slot Slot where the VFC resides. shelf/slot/port Specifies the T1 or E1 controller. dspm/dsp/dsp channel Indicates which DSP channel is engaged in this call. dsp Indicates the DSP through which this call is established. slot/port Logical port number for the device.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show csm Table 34 show csm voice Field Descriptions (continued) Field Description device_status The status of the device. Possible values are as follows: Cisco IOS Voice, Video, Fax Command Reference VR-704 • VDEV_STATUS_UNLOCKED—Device is unlocked (meaning that it is available for new calls). • VDEV_STATUS_ACTIVE_WDT—Device is allocated for a call and the watchdog timer is set to time the connection response from the central office.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show csm Table 34 show csm voice Field Descriptions (continued) Field Description csm_state CSM call state of the current call (PRI line) associated with this device. Possible values are as follows: • CSM_IDLE_STATE—Device is idle. • CSM_IC_STATE—A device has been assigned to an incoming call. • CSM_IC1_COLLECT_ADDR_INFO—A device has been selected to perform ANI/DNIS address collection for this call.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show csm Table 34 show csm voice Field Descriptions (continued) Field Description csm_state: invalid_event_count= Number of invalid events received by the CSM state machine. wdt_timeout_count= Number of times the watchdog timer is activated for this call. wdt_timestamp_started Indicates whether the watchdog timer is activated for this call.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show csm Table 34 show csm voice Field Descriptions (continued) Field Description total_busy_rbs_time slot = Total number of RBS (CAS) time slots that have been busied-out. This includes both dynamically and statically busied out RBS time slots. total_dynamic_busy_rbs_ti Total number of RBS (CAS) time slots that have been dynamically me slot = busied out.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show dial-peer video show dial-peer video To display dial-peer configuration, use the show dial-peer video command in privileged EXEC mode. show dial-peer video [number] [summary] Syntax Description number (Optional) A specific video dial peer. This option displays configuration information for a single dial peer identified by the argument number. Valid entries are any integers that identify a specific dial peer, from 1 to 32767.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show dial-peer voice show dial-peer voice To display configuration information for dial peers, use the show dial-peer voice command in privileged EXEC mode. show dial-peer voice [number] [summary] Syntax Description number (Optional) A specific dial peer. This option displays configuration information for a single dial peer identified by the number argument. Valid entries are any integers that identify a specific dial peer, from 1 to 32767.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show dial-peer voice Successful Calls = 0, Failed Calls = 0 Accepted Calls = 0, Refused Calls = 0 Last Disconnect Cause is “” Last Disconnect Text is “” Last Setup Time = 0 The following is sample output from the show dial-peer voice command for a VoIP dial peer: Router# show dial-peer voice 10 VoiceOverIpPeer10 tag = 10, dest-pat = `', incall-number = `+14087', group = 0, Admin state is up, Operation state is down Permission is Answer, type = voip, s
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show dial-peer voice Table 35 Related Commands show dial-peer voice Field Descriptions (continued) Field Description huntstop Indicates whether dial-peer hunting has been turned on, by using the huntstop command, for this dial peer. Icpif Configured Calculated Planning Impairment Factor (ICPIF) value for calls sent by a dial peer. incall-number Full E.164 telephone number to be used to identify the dial peer.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show dialplan incall number show dialplan incall number To show which plain old telephone service (POTS) dial peer is matched for a specific calling number or voice port, use the show dialplan incall number command in privileged EXEC mode. show dialplan incall voice-port number calling-number [timeout] Syntax Description voice-port Specifies the voice port location. The syntax of this argument is platform-specific.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show dialplan incall number Examples The following example shows that an incoming call from interface 1/0/0:D with a calling number of 12345 is matched to POTS dial peer 10: Router# show dialplan incall 1/0/0:D number 12345 Macro Exp.: 12345 VoiceEncapPeer10 information type = voice, tag = 10, destination-pattern = `123..
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show dialplan incall number forward-digits 4 session-target = `', voice-port = `1/0/1:D', direct-inward-dial = enabled, digit_strip = enabled, register E.164 number with GK = TRUE Connect Time = 0, Charged Units = 0, Successful Calls = 0, Failed Calls = 0, Accepted Calls = 0, Refused Calls = 0, Last Disconnect Cause is "", Last Disconnect Text is "", Last Setup Time = 0.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show dialplan incall number Table 36 Related Commands show dialplan number Field Descriptions (continued) Field Description digit_strip Whether digit stripping is enabled or disabled in the dial peer. Enabled is the default. session-protocol Session protocol to be used for Internet calls between local and remote router via the IP backbone. Connect Time Unit of measure indicating the call connection time associated with this dial peer.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show dialplan number show dialplan number To show which dial peer is reached when a particular telephone number is dialed, use the show dialplan number command in privileged EXEC mode. show dialplan number dial string [huntstop] [timeout] Syntax Description dial string Specifies a particular destination pattern (telephone number). huntstop (Optional) Terminates further dial-peer hunting upon encountering the first dial string match.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show dialplan number direct-inward-dial = disabled, Connect Time = 0, Charged Units = 0, Successful Calls = 0, Failed Calls = 0, Incomplete Calls = 0 Accepted Calls = 0, Refused Calls = 0, Last Disconnect Cause is "", Last Disconnect Text is "", Last Setup Time = 0.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show dialplan number Last Disconnect Text is "", Last Setup Time = 0. Matched: 1001 Digits: 4 Target: Table 37 explains the significant fields shown in this example. Table 37 Related Commands show dialplan number Field Descriptions Field Description Macro Exp. Expected destination pattern for this dial peer. VoiceEncapPeer Dial peer associated with the destination pattern entered. type Type of dial peer (POTS or VoIP).
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show frame-relay vofr show frame-relay vofr To display information about the FRF.11 subchannels being used on Voice over Frame Relay (VoFR) data link connection identifiers (DLCIs), use the show frame-relay vofr command in privileged EXEC mode. show frame-relay vofr [interface [dlci [cid]]] Syntax Description interface (Optional) The specific interface type and number for which you wish to display FRF.11 subchannel information.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show frame-relay vofr The following is sample output from the show frame-relay vofr command when an interface is specified: Router# show frame-relay vofr serial0 interface Serial0 Serial0 Serial0 vofr-type VoFR VoFR VoFR dlci 16 16 16 cid 4 5 10 cid-type data call-control voice The following is sample output from the show frame-relay vofr command when an interface and a DLCI are specified: Router# show frame-relay vofr serial0 16 VoFR Configuratio
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show frame-relay vofr Command Description show frame-relay pvc Displays statistics about PVCs for Frame Relay interfaces. show voice-port Displays configuration information about a specific voice port.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show gatekeeper calls show gatekeeper calls To show the status of each ongoing call of which a gatekeeper is aware, use the show gatekeeper calls command in privileged EXEC mode. show gatekeeper calls Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes Privileged EXEC Command History Release Modification 11.3(2)NA This command was introduced. 12.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show gatekeeper calls Table 39 describes the significant fields shown in the display. Table 39 Related Commands show gatekeeper calls Field Descriptions Field Description LocalCallID Identification number of the call. Age(secs) The age of the call in seconds. BW(Kbps) The bandwidth in use, in kilobits per second.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show gatekeeper endpoints show gatekeeper endpoints To display the status of all registered endpoints for a gatekeeper, use the show gatekeeper endpoints command in EXEC mode. show gatekeeper endpoints Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes EXEC Command History Release Modification 11.3(2)NA This command was introduced. 12.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show gatekeeper endpoints Table 40 Related Commands show gatekeeper endpoints Field Descriptions (continued) Field Description Type The endpoint type (for example, terminal, gateway, or MCU). F S—Indicates that the endpoint is statically entered from the alias command rather than being dynamically registered through RAS messages. O—Indicates that the endpoint, which is a gateway, has sent notification that it is nearly out of resources.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show gatekeeper gw-type-prefix show gatekeeper gw-type-prefix To display the gateway technology prefix table, use the show gatekeeper gw-type-prefix command in privileged EXEC mode. show gatekeeper gw-type-prefix Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes Privileged EXEC Command History Release Modification 11.3(2)NA This command was introduced. 12.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show gatekeeper gw-type-prefix Table 41 describes the fields contained in the show gatekeeper gw-type-prefix sample output. Table 41 show gatekeeper gw-type-prefix Field Descriptions Field Description Prefix The technology prefix defined with the gw-type-prefix command. Zone sj-gk master gateway list A list of all the gateways registered to zone sj-gk with the technology prefix, under which they are listed.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show gatekeeper gw-type-prefix Related Commands Command Description show gatekeeper calls Displays the status of each ongoing call that a gatekeeper is aware of. show gatekeeper endpoints Displays the status of all registered endpoints for a gatekeeper. show gateway Displays the current gateway status.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show gatekeeper servers show gatekeeper servers To see a list of currently registered and statically configured triggers on this gatekeeper router, enter the show gatekeeper servers command in EXEC mode. show gatekeeper servers [gkid] Syntax Description gkid Command Modes EXEC Command History Release Modification 12.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show gatekeeper servers ARQ Priority:1 Server-ID:sj-server Server IP address:1.14.93.28:42387 Server type:dynamically registered Connection Status:active Trigger Information: Destination Info:M:nilkant@zone14.com Destination Info:E:1800.......
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show gatekeeper status show gatekeeper status To show overall gatekeeper status, including authorization and authentication status, zone status, and so on, use the show gatekeeper status command in EXEC mode. show gatekeeper status Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes EXEC Command History Release Modification 11.3(2)NA This command was introduced. 12.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show gatekeeper zone prefix show gatekeeper zone prefix To display the zone prefix table, use the show gatekeeper zone prefix command in privileged EXEC mode. show gatekeeper zone prefix Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes Privileged EXEC Command History Release Modification 11.3(2)NA This command was introduced.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show gatekeeper zone status show gatekeeper zone status To display the status of zones related to a gatekeeper, use the show gatekeeper zone status command in privileged EXEC mode. show gatekeeper zone status Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes Privileged EXEC Command History Release Modification 11.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show gatekeeper zone status Table 44 describes the significant fields shown in the display. Table 44 Related Commands show gatekeeper zone status Field Descriptions Field Description GK name The gatekeeper name (also known as zone name), which is truncated after 12 characters in the display. Domain Name The domain with which the gatekeeper is associated.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show gateway show gateway To display the current gateway status, use the show gateway command in privileged EXEC mode. show gateway Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes Privileged EXEC Command History Release Modification 11.3(6)NA2 This command was introduced on the Cisco 2600 series and Cisco 3600 series routers. 12.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show gateway H323-ID gateway1 H323 resource thresholding is Enabled and Active H323 resource threshold values: DSP: Low threshold 60, High threshold 70 DS0: Low threshold 60, High threshold 70 The following example shows the report that appears when the gateway is registered with a gatekeeper and H.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show interface dspfarm show interface dspfarm To display digital signal processor (DSP) information on the two-port T1/E1 high-density port adapter for the Cisco 7200 series, use the show interface dspfarm command in privileged EXEC mode. show interface dspfarm [slot/port] Syntax Description slot (Optional) Slot location of the port adapter. /port (Optional) Port number on the port adapter. Defaults No default behavior or values.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show interface dspfarm 30887 packets input, 616516 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 30921 packets output, 7868892 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 output buffer failures, 0 output buffers swapped out Table 45 describes the significant fields shown in the display.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show interface dspfarm Table 45 show interface dspfarm Field Descriptions (continued) Field Description Tx packets Number of transmit (tx) packets. Tx frags Number of tx packets that were fragmented. Curr_dsp_tx_queued Number of tx packets that are being queued at host DSP queues. Max_dsp_tx_queued The max total tx packets that were queued at host DSP queues.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show interface dspfarm Table 45 show interface dspfarm Field Descriptions (continued) Field Description Giants Number of packets that are discarded because they exceed the maximum packet size for the medium. For instance, any Ethernet packet that is greater than 1518 bytes is considered a giant. Throttles Number of times the receiver on the port was disabled, possibly because of buffer or processor overload.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show interface dspfarm Table 45 show interface dspfarm Field Descriptions (continued) Field Description Interface resets Number of times an interface has been completely reset. Resetting can happen if packets queued for transmission were not sent within a certain interval. If the system notices that the carrier detect line of an interface is up, but the line protocol is down, it periodically resets the interface in an effort to restart it.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show mgcp show mgcp To display Media Gateway Control Protocol (MGCP) configuration information, use the show mgcp command in EXEC mode. show mgcp Defaults No defaults Command Modes EXEC Command History Release Modification 12.1(1)T This command was introduced for the Cisco AS5300 universal access server. 12.1(3)T Output was updated to show additional gateway and platform information.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show mgcp Table 46 describes the significant fields shown in the display. Table 46 show mgcp Field Descriptions MGCP Admin State...Oper State The administrative and operational state of the MGCP daemon. The administrative state controls starting and stopping the application using the mgcp and mgcp block-newcalls commands. The operational state controls normal MGCP operations.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show mgcp Table 46 show mgcp Field Descriptions (continued) MGCP IP ToS high reliability The high-reliability parameter setting for the mgcp ip-tos command. Related Commands MGCP IP ToS low cost The low-cost parameter setting for the mgcp ip-tos command. MGCP IP precedence The precedence parameter setting for the mgcp ip-tos command. MGCP default package The default-package parameter setting for the mgcp default-package command.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show mgcp connection show mgcp connection To display Media Gateway Control Protocol (MGCP) configuration information, use the show mgcp connection command in EXEC mode. show mgcp connection Syntax Description connection Defaults No defaults Command Modes EXEC Command History Release Modification 12.1(1)T This command was introduced for the Cisco AS5300 universal access server. 12.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show mgcp connection Table 47 show mgcp connection Field Descriptions (continued) (P)ort The ports used for this connection. The first port is the local UDP port. The second port is the remote UDP port. (M)ode The call mode, where: 0—An invalid value for mode. 1—The gateway should only send packets. 2—The gateway should only receive packets. 3—The gateway can send and receive packets. 4—The gateway should neither send nor receive packets.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show mgcp endpoint show mgcp endpoint To display Media Gateway Control Protocol (MGCP) configuration information, use the show mgcp endpoint command in EXEC mode. show mgcp endpoint Syntax Description endpoint Defaults No defaults Command Modes EXEC Command History Release Modification 12.1(1)T This command was introduced for the Cisco AS5300 universal access server. 12.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show mgcp statistics show mgcp statistics To display Media Gateway Control Protocol (MGCP) configuration information, use the show mgcp statistics command in EXEC mode. show mgcp statistics Syntax Description statistics Defaults No defaults Command Modes EXEC Command History Release Modification 12.1(1)T This command was introduced for the Cisco AS5300 universal access server. 12.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show mgcp statistics Table 48 describes the significant fields shown in the display. Table 48 show mgcp statistics Field Descriptions UDP pkts rx, tx The number of UDP packets transmitted and received by the gateway’s MGCP application from the Call Agent. Unrecognized rx pkts The number of unrecognized UDP packets received by the MGCP application. MGCP message parsing errors The number of MGCP messages received with parsing errors.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show mgcp statistics show mgcp connection Displays connection-related MGCP configuration information. show mgcp endpoint Displays endpoint-specific MGCP configuration information.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show num-exp show num-exp To show the number expansions configured, use the show num-exp command in privileged EXEC mode. show num-exp [dialed-number] Syntax Description dialed-number Defaults No default behavior or values. Command Modes Privileged EXEC Command History Release Modification 11.3(1)T This command was introduced on the Cisco 3600 platform. 12.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show num-exp Table 49 describes the significant fields shown in the display. Table 49 Related Commands show num-exp Field Descriptions Field Description Dest Digit Pattern Index number identifying the destination telephone number digit pattern. Translation Expanded destination telephone number digit pattern. Command Description show call active voice Displays the Voice over IP active call table.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show pots csm show pots csm To show the current state of calls and the most recent event received by the call switching module (CSM) on the Cisco 800 series router, use the show pots csm command in EXEC mode. show pots csm port Syntax Description port Command Modes EXEC Command History Release Modification 12.1.(2)XF This command was introduced on the Cisco 800 series routers. Examples Port number 1 or 2.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show pots status show pots status To display the settings of the telephone port physical characteristics and other information on the telephone interfaces of the Cisco 800 series, use the show pots status command in privileged EXEC mode. show pots status [1 | 2] Syntax Description 1 (Optional) Display the settings of telephone port 1. 2 (Optional) Display the settings of telephone port 2. Defaults No default behavior or values.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show pots status CODEC Registers: SPI Addr: 2, DSLAC Revision: 4 SLIC Cmd: 0D, TX TS: 00, RX TS: 00 Op Fn: 6F, Op Fn2: 00, Op Cond: 00 AISN: 6D, ELT: B5, EPG: 32 52 00 00 SLIC Pin Direction: 1F CODEC Coefficients: GX: A0 00 GR: 3A A1 Z: EA 23 2A 35 A5 9F C2 AD 3A AE 22 46 C2 F0 B: 29 FA 8F 2A CB A9 23 92 2B 49 F5 37 1D 01 X: AB 40 3B 9F A8 7E 22 97 36 A6 2A AE R: 01 11 01 90 01 90 01 90 01 90 01 90 GZ: 60 ADAPT B: 91 B2 8F 62 31 CSM Finite State Machin
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show pots status Table 50 describes the significant fields shown in the display. Table 50 show pots status Field Descriptions Field Descriptions POTS Global Configuration Displays the settings of the telephone port physical characteristic commands. Also displays the following: • TX GAIN—Current transmit gain of telephone ports. • RX LOSS—Current transmit loss of telephone ports.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show pots status Command Description pots silence-time Specifies the interval of silence after a calling party disconnects (Cisco 800 series router). pots tone-source Specifies the source of dial, ringback, and busy tones for telephones, fax machines, or modems connected to a Cisco 800 series router.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show proxy h323 calls show proxy h323 calls To list each active call on the proxy, use the show proxy h323 calls command in privileged EXEC mode. show proxy h323 calls Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes Privileged EXEC Command History Release Modification 11.3(2)NA This command was introduced. 12.0(3)T The command was integrated into Cisco IOS Release 12.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show proxy h323 detail-call show proxy h323 detail-call To display the details of a particular call on a proxy, use the show proxy h323 detail-call command in privileged EXEC mode. show proxy h323 detail-call call-key Syntax Description call-key Defaults No default behavior or values. Command Modes Privileged EXEC Command History Release Specifies the call you want to display.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show proxy h323 detail-call Bandwidth = 374 kbps Time created = 731146318 ms Channel number = 1 Type = AUDIO State = OPEN Bandwidth = 81 kbps Time created = 731146317 ms H245 logical channels for call leg pte111@zone1.com<->50.0.0.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show proxy h323 detail-call State = OPEN Bandwidth = 225 kbps Time created = 730949664 ms RTP Statistics: Packet Received Count = 3390 Packet Dropped Count = 0 Packet Out of Sequence Count = 0 Number of initial packets used for Arrival-Spacing bin setup = 200 min_arrival_spacing = 0(ms) max_arrival_spacing = 856(ms) Average Arrival Rate = 86(ms) Arrival-Spacing(ms) Packet-Count 0 2116 26 487 52 26 78 0 104 0 130 1 156 0 182 1 208 0 234 4 260 99 286 315
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show proxy h323 detail-call Min Jitter = 0(ms) Max Jitter = 28(ms) Average Jitter Rate = 5 Jitter Rate(ms) Packet-Count 0 1069 3 2720 6 0 9 804 12 27 15 10 18 0 21 56 24 177 27 35 H245 logical channels for call leg cisco7-pxy <-> proxy.sanjose.cisco.com: Channel number = 259 RTP stream from cisco7-pxy to proxy.sanjose.cisco.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show proxy h323 detail-call Channel number = 257 RTP stream from cisco7-pxy to proxy.sanjose.cisco.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show proxy h323 detail-call Related Commands Command Description h323 qos Enables QoS on the proxy.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show proxy h323 status show proxy h323 status To display the overall status of a proxy, use the show proxy h323 status command in privileged EXEC mode. show proxy h323 status Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes Privileged EXEC Command History Release Modification 11.3(2)NA This command was introduced. 12.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show rawmsg show rawmsg To show the raw messages owned by the required component, use the show rawmsg command in privileged EXEC mode. show rawmsg {all | tsp | vtsp | ccapi | h323} Syntax Description all All selections below. tsp Telephony Service Provider subsystem. vtsp Voice Telephony Service Provider subsystem. ccapi API (Application Programming Interface) used to coordinate interaction between application and call legs (telephony or IP).
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show rlm group statistics show rlm group statistics To display the network latency of the Redundant Link Manager (RLM) group, use the show rlm group statistics command in privileged EXEC mode. show rlm group group-number statistics Syntax Description group-number Command Modes Privileged EXEC Command History Release Modification 11.3(7) This command was introduced. Examples RLM group number (0 to 255).
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show rlm group statistics Server Link Group[r2-server]: Open the link [10.1.1.1(Loopback1), 10.1.5.1]: last time occurred at 02:46:06.724, success=0(0%), failure=1 avg=0.000s, max=0.000s, min=0.000s, latest=0.000s Echo over link [10.1.1.1(Loopback1), 10.1.5.1]: last time occurred at 02:47:18.724, success=0(0%), failure=85 avg=0.000s, max=0.000s, min=0.000s, latest=0.000s Open the link [10.1.1.2(Loopback2), 10.1.5.2]: last time occurred at 02:46:06.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show rlm group statistics Related Commands Command Description clear interface Resets the hardware logic on an interface. clear rlm group Clears all RLM group time stamps to zero. interface Defines the IP addresses of the server, configures an interface type, and enters interface configuration mode. link (RLM) Specifies the link preference. protocol rlm port Reconfigures the port number for the basic RLM connection for the whole rlm-group.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show rlm group status show rlm group status To display the status of the Redundant Link Manager (RLM) group, use the show rlm group status command in privileged EXEC mode. show rlm group group-number status Syntax Description group-number Command Modes Privileged EXEC Command History Release Modification 11.3(7) This command was introduced. Examples RLM group number (0 to 255).
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show rlm group status Table 52 Related Commands show rlm group status Field Descriptions (continued) Field Description socket The status of the individual signaling link. Server Link Group[r2-server] The status of all signaling links configured under a particular RLM server link group (r2-server). Command Description clear interface Resets the hardware logic on an interface. clear rlm group Clears all RLM group time stamps to zero.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show rlm group timer show rlm group timer To display the current timer values, use the show rlm group timer command in privileged EXEC mode. show rlm group group-number timer Syntax Description group-number Command Modes Privileged EXEC Command History Release Modification 11.3(7) This command was introduced. Examples RLM group number (0 to 255).
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show rlm group timer Related Commands Command Description clear interface Resets the hardware logic on an interface. clear rlm group Clears all RLM group time stamps to zero. interface Defines the IP addresses of the server, configures an interface type, and enters interface configuration mode. link (RLM) Specifies the link preference. protocol rlm port Reconfigures the port number for the basic RLM connection for the whole rlm-group.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show rtsp client session show rtsp client session To display cumulative information about Real Time Streaming Protocol (RTSP) session records, use the show rtsp client session command in privileged EXEC mode. To set the value to the default, use the no form of this command.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show rtsp client session Examples The following output is displayed when the show rtsp client session active command is used during an active session: Router# show rtsp client session active RTSP Session ID:0x8 Current Status:RTSP_STATUS_PLAYING Associated CallID:0xF Active Request:RTSP_API_REQ_PLAY Control Protocol:TCP Data Protocol:RTP Total Packets Transmitted:0 (0 bytes) Total Packets Received:708 (226560 bytes) Cumulative Elapsed Play Time:00:00:
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show rtsp client session Related Commands Command Description rtsp client session history Specifies the length of time the RTSP is kept during the session. duration rtsp client session history Specifies the number of RTSP client session history records during the records session.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show rudpv0 failures show rudpv0 failures To show SS7 Reliable User Datagram Protocol (RUDP) failure statistics, enter the show rudpv0 failures command in privileged EXEC mode. show rudpv0 failures Syntax Description There are no keywords or arguments. Defaults There are no default behaviors or values. Command History Release Modification 12.0(7)XR This command was introduced. 12.1(1)T This command was integrated into Cisco IOS Release 12.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show rudpv0 failures Related Commands Command Description clear rudpv0 statistics Resets the counters for the statistics generated by show rudpv0 failures to 0. show rudpv0 statistics Displays RUDP information about number of packets sent, received, and so forth. clear rudpv0 statistics resets the counters for these statistics to 0.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show rudpv0 statistics show rudpv0 statistics To show SS7 Reliable User Datagram Protocol (RUDP) internal statistics, enter the show rudpv0 statistics privileged EXEC command. show rudpv0 statistics Syntax Description There are no keywords or arguments. Defaults There are no default behaviors or values. Command History Release Modification 12.0(7)XR This command was introduced. 12.1(1)T This command was integrated into Cisco IOS Release 12.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show rudpv0 statistics SoftResets SoftResetsRcvd 0 0 TotalPacketsSent TotalPacketsReceived TotalDataBytesSent TotalDataBytesReceived TotalDataPacketsSent TotalDataPacketsReceived TotalPacketsRetrans TotalPacketsDiscarded 7863 6755 173690 56121 2695 2265 0 0 Cumulative RudpV0 Statistics Related Commands RcvdInSeq RcvdOutOfSeq 2266 0 SoftResets SoftResetsRcvd 0 0 TotalPacketsSent TotalPacketsReceived TotalDataBytesSent TotalDataBytesReceived To
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show rudpv1 show rudpv1 To display Reliable User Datagram Protocol (RUDP) information, use the show rudpv1 command in privileged EXEC mode. show rudpv1 { failures | parameters | statistics } Syntax Description failures RUDP failure statistics. parameters RUDP connection parameters. statistics RUDP internal statistics. Defaults No default behavior or values. Command Modes Privileged EXEC Command History Release Modification 12.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show rudpv1 BufferTooLargeFailures ConnNotOpenFailures SendWindowFullFailures GetBufHdrSendFailures 0 0 0 0 SendInProgressFailures 0 GetDataBufFailures GetBufHdrFailures 0 0 SendFailures SendEackFailures SendAckFailures SendSynFailures SendRstFailures SendTcsFailures SendNullFailures 0 0 0 0 0 0 0 TimerFailures ApplQueueFailures FailedRetransmits IncomingPktsDropped CksumErrors UnknownRudpv1Events InvalidVersion InvalidNegotiation 0 0 0 0 0 0
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show rudpv1 Send Seg Size Max Auto Reset Max Cum Ack Max Retrans Max OutOfSeq Cum Ack Timeout Retrans Timeout Null Seg Timeout Trans State Timeout Cksum type 384 Requested 5 3 2 3 100 300 1000 2000 Hdr Negotiated 5 3 2 3 100 300 1000 2000 Hdr The following example shows sample output for show rudpv1 statistics: Router# show rudpv1 statistics *** RUDPV1 Internal Stats **** Connection ID:61F72B6C, Current State:OPEN RcvdInSeq RcvdOutOfSeq 647 95
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show rudpv1 TotalPacketsReceived TotalDataBytesSent TotalDataBytesReceived TotalDataPacketsSent TotalDataPacketsReceived TotalPacketsRetrans TotalPacketsDiscarded Related Commands Command Description clear rudpv1 statistics Clears the RUDP statistics counters. debug rudpv1 Displays debugging information for RUDP.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show settlement show settlement To display the configuration for all settlement servers and see the specific provider and transactions, use the show settlement command in privileged EXEC mode. To reset to the default value, use the no form of this command. show settlement [provider-number [transactions]] no show settlement [provider-number [transactions]] Syntax Description provider-number (Optional) Displays the attributes of a specific provider.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show settlement The following example shows transaction and state information about a specific settlement server: Router# show settlement 0 transactions Transaction ID=8796304133625270342 state=OSPC_GET_DEST_SUCCESS, index=0 callingNumber=5710868, calledNumber=15125551212 Table 54 describes the significant fields shown in the display. The provider attributes not configured are not shown. .
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show sgcp connection show sgcp connection To see all active SGCP connections on this router, use the show sgcp connection command in EXEC mode. show sgcp connection [interface number] Syntax Description interface (Optional) Specifies a DS1 interface. number (Optional) Specifies the T1 interface (controller) number. Valid values on the Cisco MC3810 multiservice concentrator are from 0 to 1. Defaults No default behavior or values.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show sgcp connection Table 55 Related Commands show sgcp connection Field Descriptions Field Description SGCP Admin State The administrative and operational state of the SGCP daemon. SGCP call-agent The address of the call agent specified in the sgcp command. SGCP graceful-shutdown enabled The state of the sgcp graceful-shutdown command. SGCP request timeout The setting for the sgcp request timeout command.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show sgcp endpoint show sgcp endpoint To see SGCP endpoints eligible for SGCP management, use the show sgcp endpoint command in EXEC mode. show sgcp endpoint [interface ds1 [ds0]] Syntax Description interface ds1 (Optional) Specifies the DS1 interface for which to display SGCP endpoint information. The valid range is from 1 to 1000. ds0 (Optional) Specifies the DS0 interface for which to display SGCP endpoint information.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show sgcp endpoint Related Commands Command Description show sgcp connection Displays all the active connections on the host router. show sgcp statistics Displays global statistics for the SGCP packet count, success, and failure counts.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show sgcp statistics show sgcp statistics To see global statistics for the SGCP packet count, success and failure counts, and other information, use the show sgcp statistics command in EXEC mode. show sgcp statistics Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes EXEC Command History Release Modification 12.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show sgcp statistics ModifyConn rx 0, successful 0, failed 0 DeleteConn tx 0, successful 0, failed 0 NotifyRequest rx 0, successful 0, failed 0 Notify tx 0, successful 0, failed 0 ACK tx 0, NACK tx 0 ACK rx 0, NACK rx 0 Router# show sgcp statistics | exclude ACK UDP pkts rx 0, tx 0 Unrecognized rx pkts 0, SGCP message parsing errors 0 Duplicate SGCP ack tx 0 Failed to send SGCP messages 0 CreateConn rx 0, successful 0, failed 0 DeleteConn rx 0, success
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show sip-ua show sip-ua To display information and settings for the Session Initiation Protocol (SIP) User Agent (UA), use the show sip-ua command in privileged EXEC mode. show sip-ua {retry | statistics | status | timers} Syntax Description retry Displays SIP protocol retry counts. statistics Displays SIP UA response, traffic, and retry statistics. status Displays SIP UA listener status.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show sip-ua OkInvite 0/0, OkBye 0/0, OkCancel 0/0, OkOptions 0/0 Redirection (Inbound only): MultipleChoice 0, MovedPermanently 0, MovedTemporarily 0, SeeOther 0, UseProxy 0, AlternateService 0 Client Error: BadRequest 0/0, Unauthorized 0/0, PaymentRequired 0/0, Forbidden 0/0, NotFound 0/0, MethodNotAllowed 0/0, NotAcceptable 0/0, ProxyAuthReqd 0/0, ReqTimeout 0/0, Conflict 0/0, Gone 0/0, LengthRequired 0/0, ReqEntityTooLarge 0/0, ReqURITooLarge 0/0, U
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show ss7 mtp2 ccb show ss7 mtp2 ccb To display SS7 MTP 2 Channel Control Block (CCB) information, use the show ss7 mtp2 ccb command in privileged EXEC mode. show ss7 mtp2 ccb [channel] Syntax Description channel Defaults The default is set when you first configure the MTP 2 variant. The link must be out of service in order to change the MTP 2 variant. Specifies a channel from 0 through 3.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show ss7 mtp2 ccb AbnormalBSN_flag UnreasonableBSN UnreasonableFSN Abnormal_FIBR_flag congestionDiscard = = = = = ThisIsA_MSU local_processor_outage remote_processor_outage = FALSE = FALSE = FALSE provingEmergencyFlag RemoteProvingEmergencyFlag further_proving_required ForceRetransmitFlag RetransmissionFlag = = = = = link_present Debug Mask = FALSE = 0x0 Cisco IOS Voice, Video, Fax Command Reference VR-796 FALSE FALSE FALSE FALSE TRUE FALSE
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show ss7 mtp2 state show ss7 mtp2 state To display internal SS7 Message Transfer Part level 2 (MTP 2) state machine information, use the show ss7 mtp2 state command in privileged EXEC mode. show ss7 mtp2 state [channel] Syntax Description channel Defaults If you do not specify a channel, the command shows state machine information for channel 0. Command Modes Privileged EXEC Command History Release Modification 12.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show ss7 mtp2 state Table 56 SS7 MTP 2 State Information Fields State Description Possible Values MTP2LSC Indicates the overall status of the OOS—The link is Out-of-Service. link. INITIAL_ALIGNMENT—The link is in a transitional link alignment state. ALIGNED_READY—The link is in a transitional link alignment state. ALIGNED_NOT_READY—The link is in a transitional link alignment state. INSERVICE—The link is in service.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show ss7 mtp2 state Table 56 SS7 MTP 2 State Information Fields (continued) State Description Possible Values MTP2AERM Indicates the status of the alignment error rate monitor state machine (AERM). IDLE—The state machine is inactive. Indicates the status of the congestion control state machine. IDLE—The state machine is inactive. No congestion is detected; normal traffic flow. MTP2CONGESTION MONITORING—Alignment error monitor is active.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show ss7 mtp2 stats show ss7 mtp2 stats To display SS7 MTP 2 operational statistics, use the show ss7 mtp2 stats command in privileged EXEC mode. show ss7 mtp2 stats [channel] Syntax Description channel Specifies a channel from 0 through 3. Defaults If you do not specify a channel, the command shows status information for channel 0. Command Modes Privileged EXEC Command History Release Modification 12.0(7)XR This command was introduced. 12.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show ss7 mtp2 stats OMLSSU_RCV_Count OMLSSU_RCV_SINCount OMLSSU_RCV_SIECount OMLSSU_RCV_SIOCount OMLSSU_RCV_SIOSCount OMLSSU_RCV_SIPOCount OMLSSU_RCV_SIBCount OMLSSU_RCV_InvalidCount = = = = = = = = 0 0 0 0 0 0 0 0 OMRemote_PO_Count = 0 OMRemote_Congestion_Cnt = 0 OMtimeINSV (secs) OMtimeNotINSV (secs) OMMSUBytesTransmitted OMMSUBytesReceived = = = = 0 9550 0 0 OMTransmitReqCount OMPDU_notAcceptedCount OMPDU_NACK_Count OMunreasonableFSN_rcvd OMun
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show ss7 mtp2 stats Table 57 SS7 OM Information Fields Field Description OMIACAlignAttemptCount Counts for Initial Alignment Control (IAC) attempts. OMIACAlignFailCount OMIACAlignCompleteCount OMMSU_TO_XMIT_Count This count is related to the results of the show ss7 sm stats command’s PDU_pkts_recieve_count statistic.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show ss7 mtp2 stats Table 57 SS7 OM Information Fields (continued) Field Description OMT1_TMO_Count These fields show information about timers in use.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show ss7 mtp2 timer show ss7 mtp2 timer To display durations of the SS7 MTP 2 state machine timers, use the show ss7 mtp2 timer command in privileged EXEC mode. show ss7 mtp2 timer [channel] Note The eight timers whose status is displayed using the show ss7 mtp2 timer command are set on the Media Gateway Controller using MML commands. The timers are then downloaded from the controller to the Cisco SLT.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show ss7 mtp2 timer Examples The following example shows how to display timer information for channel 0: Router# show ss7 mtp2 timer 0 SS7 MTP2 Timers for channel 0 in milliseconds Protocol version for channel 0 is Japan NTT Q.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show ss7 mtp2 variant show ss7 mtp2 variant To display information about the SS7 MTP 2 protocol variant, use the show ss7 mtp2 variant command in privileged EXEC mode. show ss7 mtp2 variant [channel] Syntax Description channel Defaults If you do not specify a channel, the command shows protocol information for channel 0. Command Modes Privileged EXEC Command History Release Modification 12.0(7)XR This command was introduced. 12.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show ss7 sm session show ss7 sm session To display information about SS7 Session Manager session, use the show ss7 sm session command in privileged EXEC mode. show ss7 sm session [session] Syntax Description session Defaults If you do not specify a session, the command shows information for both sessions. Command Modes Privileged EXEC Command History Release Modification 12.0(7)XR This command was introduced. 12.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show ss7 sm session Table 58 Related Commands Session Manager Session Information Field Description Remote Host, Local Host Shows the IP address and port number for the session. retrans_t Shows the retransmission timer value. cumack_t Shows the cumulative acknowledgment timer value. m_cumack Shows the maximum number of segments that can be received before the RUDP sends an acknowledgment.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show ss7 sm set show ss7 sm set To display information about the SS7 failover timer, use the show ss7 sm set command in privileged EXEC mode. show ss7 sm set Syntax Description There are no arguments or keywords. Defaults There is no default. Command Modes Privileged EXEC Command History Release Modification 12.0(7)XR This command was introduced. 12.1(1)T This command was integrated into Cisco IOS Release 12.1(1)T.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show ss7 sm stats show ss7 sm stats To display SS7 Session Manager session statistics, use the show ss7 sm stats command in privileged EXEC mode. show ss7 sm stats Syntax Description There are no arguments or keywords for this command. Defaults The command shows information for both sessions. Command Modes Privileged EXEC Command History Release Modification 12.0(7)XR This command was introduced. 12.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show ss7 sm stats Pkts send count Pkts requeue count -Pkts window full count -Pkts resource unavail count -Pkts enqueue fail count PDUs dropped (Large) PDUs dropped (Empty) = = = = = = = 0 0 0 0 0 0 0 RUDP Not Ready Errs RUDP Connection Not Open RUDP Invalid Conn Handle RUDP Unknown Errors RUDP Unknown Signal NonActive Receive count = = = = = = 0 0 0 0 0 0 Session[1] statistics Session Down count Open Retry count Related Commands SM SESSION STA
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show translation-rule show translation-rule To display the contents of the rules that have been configured for a specific translation name, use the show translation-rule command in privileged EXEC mode. show translation-rule [name-tag] Syntax Description name-tag Command Modes Privileged EXEC Command History Release Modification 12.0(7)XR1 This command was introduced for Voice over IP on the Cisco AS5300 universal access server. 12.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show translation-rule Examples The following example shows output for the show translation-rule command: Router# show translation-rule Translation rule address:0x61AB94F8 Tag name:21 Translation rule in_used 1 **** Xrule rule table ******* Rule :1 in_used state:1 Match pattern:555.% Sub pattern:1408555 Match type:subscriber Sub type:international **** Xrule rule table ******* Rule :2 in_used state:1 Match pattern:8.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show translation-rule Command Description translate Applies a translation rule to a calling party number or a called party number for incoming calls. translate-outgoing Applies a translation rule to a calling party number or a called party number for outgoing calls. translation-rule Creates a translation name and enters translation-rule configuration mode. voip-incoming translation-rule Captures calls that originate from H.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show vfc show vfc To see the entries in the host-name-and-address cache, use the show vfc command in privileged EXEC mode. show vfc slot-number [technology] Syntax Description slot-number VFC slot number. technology (Optional) Displays the technology type of the VFC. Defaults No default behavior or values. Command Modes Privileged EXEC Command History Release Modification 11.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show vfc cap-list show vfc cap-list To show the current list of files on the capability list for this voice feature card (VFC), use the show vfc cap-list command in user EXEC mode. show vfc slot cap-list Syntax Description slot Defaults No default behavior or values. Command Modes User EXEC Command History Release Modification 11.3 NA This command was introduced on the Cisco AS5300 universal access server.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show vfc default-file show vfc default-file To show the default files included in the default file list for a voice feature card (VFC), use the show vfc default-file command in user EXEC mode. show vfc slot default-file Syntax Description slot Defaults No default behavior or values. Command Modes User EXEC Command History Release Modification 11.3 NA This command was introduced on the Cisco AS5300 universal access server.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show vfc directory show vfc directory To show the list of all files residing on a voice feature card (VFC), use the show vfc directory command in user EXEC mode. show vfc slot directory Syntax Description slot Defaults No default behavior or values. Command Modes User EXEC Command History Release Modification 11.3 NA This command was introduced on the Cisco AS5300 universal access server. Identifies the slot where the VFC is installed.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show vfc directory Related Commands Command Description show vfc cap-list Displays the current list of files on the capability list for this VFC. show vfc default-file Displays the default files included in the default file list for this VFC. show vfc version Displays the version of the software residing on this VFC.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show vfc version show vfc version To show the version of the software residing on a voice feature card (VFC), use the show vfc version command in user EXEC mode. show vfc slot version {dspware | vcware} Syntax Description slot Identifies the slot where the VFC is installed. Valid values are 0, 1, and 2. dspware Defines which DSPWare software to display. vcware Defines which VCWare software to display. Defaults No default behavior or values.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show video call summary show video call summary To display summary information about video calls and the current status of the Video Call Manager (ViCM), use the show video call summary command in privileged EXEC mode. show video call summary Syntax Description There are no arguments or keywords. Defaults No default behavior or values. Command Modes Privileged EXEC Command History Release Modification 12.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice busyout show voice busyout To display information about the voice busyout state, use the show voice busyout command in privileged EXEC mode. show voice busyout Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes Privileged EXEC Command History Release Modification 12.0(3)T This command was introduced on the Cisco MC3810 multiservice concentrator. 12.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice busyout Related Commands Command Description busyout forced Forces a voice port into the busyout state. busyout monitor Places a voice port in the busyout monitor state. busyout seize Changes the busyout seize procedure from a voice port. voice-port busyout Places all voice ports associated with a serial or ATM interface in a busyout state.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice call show voice call To show the call status for voice ports on the Cisco router or concentrator, use the show voice call EXEC command.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice call For the Cisco MC3810 Multiservice Concentrator with Analog Voice Ports: slot/port summary (Optional) Displays information for the analog voice port you specify with the slot/port designation. • slot is the physical slot in which the analog voice module (AVM) is installed. The slot is always 1 for analog voice ports in the Cisco MC3810 multiservice concentrator. • port specifies an analog voice port number.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice call The show voice call command provides the status at these levels of the call handling module: Examples • Tandem switch • End-to-end call manager • Call processing state machine • Protocol state machine The following is a sample display from the show voice call summary command for voice ports on a Cisco MC3810 multiservice concentrator, showing two local calls connected without local bypass: PORT ======= 0:17.18 0:18.19 0:19.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice call sys252#show voice call 1/4 1/4 vtsp level 0 state = S_CONNECT vpm level 1 state = S_TRUNKED vpm level 0 state = S_UP router#***DSP VOICE VP_DELAY STATISTICS*** Clk Offset(ms): 1445779863, Rx Delay Est(ms): 95 Rx Delay Lo Water Mark(ms): 95, Rx Delay Hi Water Mark(ms): 125 ***DSP VOICE VP_ERROR STATISTICS*** Predict Conceal(ms): 10, Interpolate Conceal(ms): 0 Silence Conceal(ms): 0, Retroact Mem Update(ms): 0 Buf Overflow Discard(ms): 20
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice dsp show voice dsp To show the current status of all digital signal processor (DSP) voice channels, use the show voice dsp command in privileged EXEC mode. show voice dsp Syntax Description This command has no arguments or keywords. Defaults No default behavior or values. Command Modes Privileged EXEC Command History Release Modification 11.3(1)MA This command was introduced on the Cisco MC3810 multiservice concentrator. 12.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice dsp Table 61 show voice dsp Field Descriptions Field Description DSP Number of the DSP. Channel Number of the channel and its status.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice permanent-call show voice permanent-call To display information about the permanent calls on a voice interface, use the show voice permanent-call command in user EXEC or privileged EXEC mode. show voice permanent-call [voice-port] [summary] Syntax Description voice-port (Optional) Slot number or slot/port number of the voice interface for which you wish to display permanent call information.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice permanent-call max timeout timer 5016 (ms), restart timeout is 0 (ms) signaling packet fast-mode inter-arrival times (ms) 16 24 16 24 16 24 16 24 16 24 16 24 16 24 16 24 16 24 16 24 16 24 16 24 0 0 0 0 0 0 0 0 signaling 1101 1101 1101 1101 1101 1101 playout history 1101 1101 1101 1101 1101 1101 1101 1101 1101 1101 1101 1101 1101 1101 1101 1101 1101 1101 1101 1101 1101 1101 1101 1101 The following is sample output for the show voice permane
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice permanent-call Table 63 describes the fields shown in these displays. Table 63 show voice permanent-call Field Descriptions Field Description state Current status of the call on this voice port. coding Codec type used for this call. payload size Size in bytes of the voice payload. vad Indicates whether voice activity detection is turned on or off. ec Echo canceler length, in milliseconds.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice permanent-call Table 63 show voice permanent-call Field Descriptions (continued) Field Description RX INFO:missing Indicates the number of FRF.11 Annex B packets that were counted as missing based on checking Annex B sequence numbers. RX INFO:out of seq Number of FRF.11 Annex B packets that were counted as received in the wrong order based on checking Annex B sequence numbers. RX INFO:very late Number of FRF.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice port show voice port To display configuration information about a specific voice port, use the show voice port command in EXEC command.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice port For the Cisco 2600 and 3600 Series Router with Analog Voice Ports: slot/subunit/port summary (Optional) Displays information for the analog voice port you specify with the slot/subunit/port designation. • slot specifies a router slot in which a voice network module (VNM) is installed. Valid entries are router slot numbers for the particular platform. • subunit specifies a voice interface card (VIC) where the voice port is located.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice port For the Cisco MC3810 Multiservice Concentrator with Digital Voice Ports: slot:ds0-group summary (Optional) Displays information for the digital voice port you specify with the slot:ds0-group designation. • slot specifies the module (and controller). Valid entries are 0 for the MFT (controller 0) and 1 for the DVM (controller 1). • ds0-group specifies a T1 or E1 logical voice port number.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice port Command Modes EXEC Command History Release Modification 11.3(1) T This command was introduced on the Cisco 3600 series router. 11.3(1)MA Port-specific values for the Cisco MC3810 multiservice concentrator were added. 12.0(3)T Port-specific values for the Cisco MC3810 multiservice concentrator were added. 12.0(5)XK The ds0-group argument was added for the Cisco 2600 and Cisco 3600 series routers. 12.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice port 0:21 22 fxo-ls 0:22 23 fxo-ls 0:23 24 e&m-imd 1/1 -- fxs-ls 1/2 -- fxs-ls 1/3 -- e&m-imd 1/4 -- e&m-imd 1/5 -- fxo-ls 1/6 -- fxo-ls Elements : sys/voip/ccvpm sys/voip/ccvtsp sys/voip/cli up up up up up up up up up dorm dorm dorm dorm dorm dorm dorm dorm dorm idle idle idle on-hook on-hook idle idle idle idle on-hook on-hook idle idle idle idle idle on-hook on-hook y y y y y y y y y vpm_htsp.c (107) vtsp_core.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice port Dial Type is dtmf In Seizure is inactive Out Seizure is inactive Digit Duration Timing is set to 0 ms InterDigit Duration Timing is set to 0 ms Pulse Rate Timing is set to 0 pulses/second InterDigit Pulse Duration Timing is set to 0 ms Clear Wait Duration Timing is set to 0 ms Wink Wait Duration Timing is set to 0 ms Wink Duration Timing is set to 0 ms Delay Start Timing is set to 0 ms Delay Duration Timing is set to 0 ms The following
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice port Connection Mode is normal Connection Number is not set Initial Time Out is set to 10 s Interdigit Time Out is set to 10 s Coder Type is g729ar8 Companding Type is u-law Voice Activity Detection is disabled Ringing Time Out is 180 s Wait Release Time Out is 30 s Nominal Playout Delay is 80 milliseconds Maximum Playout Delay is 160 milliseconds Analog Info Follows: Region Tone is set for northamerica Currently processing Voice Maintenance
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice port The following is sample output from the show voice port summary command for all voice ports on a Cisco MC3810 multiservice concentrator with an analog voice module (AVM): IN OUT ECHO PORT SIG-TYPE 1/1 fxs-ls 1/2 fxs-ls 1/3 e&m-wnk 1/4 e&m-wnk 1/5 fxo-ls 1/6 fxo-ls ADMIN up up up up up up OPER up up up up up up IN-STATUS OUT-STATUS CODEC on-hook idle 729a on-hook idle 729a idle idle 729a idle idle 729a idle on-hook 729a idle on-hook 7
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice port Table 64 show voice port Field Descriptions (continued) Field Description InterDigit Pulse Duration Timing Pulse dialing interdigit timing, in milliseconds. Interdigit Time Out Amount of time the system waits for a subsequent input digit from the caller. Maintenance Mode Maintenance mode of the voice port.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice port Table 64 show voice port Field Descriptions (continued) Field Description Wait Release Time Out The length of time a voice port stays in the call-failure state while the Cisco MC3810 multiservice concentrator sends a busy tone, a reorder tone, or an out-of-service tone to the port. Wink Duration Timing Maximum wink duration for wink start signaling. Wink Wait Duration Timing Maximum wink wait duration for wink start signaling.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice port Table 65 describes the significant fields shown in the display. Table 65 show voice port Field Descriptions for the Cisco AS5800 Field Description Type of VoicePort Indicates the voice port type. Operational State Operational state of the voice port. Administrative State Administrative state of the voice port. Clear Wait Duration Timing Time of inactive seizure signal to declare call cleared.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice trunk-conditioning signaling show voice trunk-conditioning signaling To display the status of trunk-conditioning signaling and timing parameters for a voice port, use the show voice trunk-conditioning signaling command in user EXEC or privileged EXEC mode.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice trunk-conditioning signaling TX INFO :slow-mode seq#= 25, sig pkt cnt= 42, last-ABCD=0000 hardware-state ACTIVE signal type is NorthamericanCAS signal path is OPEN 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 RX INFO :slow-mode, sig pkt cnt= 37 missing = 0, out of seq = 0, very late = 0 playout depth = 0 (ms), refill count = 1 prev-seq#=
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice trunk-conditioning signaling Table 66 describes the significant fields shown in the display. Table 66 show voice trunk-conditioning signaling Field Descriptions Field Description current timer Time since last signaling packets were received.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice trunk-conditioning signaling Related Commands Command Description show dial-peer voice Displays the configuration for all VoIP and POTS dial peers configured on the router. show voice dsp Shows the current status of all DSP voice channels. show voice port Displays configuration information about a specific voice port.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice trunk-conditioning supervisory show voice trunk-conditioning supervisory To display the status of trunk supervision and configuration parameters for a voice port, use the show voice trunk-conditioning supervisory command in user EXEC or privileged EXEC mode.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice trunk-conditioning supervisory The following is a sample display from the show voice trunk-conditioning supervisory summary command for voice ports on a Cisco 3600 series router: Router# show voice trunk-conditioning supervisory summary 2/0/0 is 2/0/1 is 3/0:0 8 3/0:1 1 3/0:2 2 3/0:3 3 3/0:5 5 3/0:6(6) 3/0:7(7) 3/1:0(8) 3/1:1(1) 3/1:3(3) 3/1:5(5) 3/1:7(7) shutdown shutdown is shutdown is shutdown is shutdown is shutdown is shutdown : state
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show voice trunk-conditioning supervisory Table 67 describes the significant fields shown in the display. Table 67 Related Commands show voice trunk-conditioning supervisory Field Descriptions Field Description keep_alive Signaling packets periodically sent to the far end, even if there is no signal change. These signaling packets function as keep alive messages. master The voice port configured as “connect trunk xxxx.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show vrm active_calls show vrm active_calls To display active-only voice calls either for a specific voice feature card (VFC) or for all VFCs, use the show vrm active_calls command in privileged EXEC mode. show vrm active_calls {dial-shelf-slot-number | all} Syntax Description dial-shelf-slot-number Slot number of the dial shelf. Valid number is 0 to 13. all Lists all active calls for VFC slots. Defaults No default behavior or values.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show vrm active_calls Table 68 describes the significant fields shown in the display. Table 68 show vrm active_calls Field Descriptions Field Description slot Slot where voice card is installed. virtual voice dev (tag) Identification number of the virtual voice device. channel id Identification number of the channel associated with this virtual voice device. capability list map Bitmaps for the codec supported on that DSP channel.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show vrm active_calls Table 68 Related Commands show vrm active_calls Field Descriptions (continued) Field Description tot egress control Total number of control packets sent from the VoIP side of the connection to the PSTN side of the connection. tot egress data drops Total number of data packets dropped from the VoIP side of the connection to the PSTN side of the connection.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show vrm vdevices show vrm vdevices To display detailed information for a specific digital signal processor (DSP) or a brief summary display for all voice feature cards (VFCs), use the show vrm vdevices command in privileged EXEC mode. show vrm vdevices {{vfc-slot-number | voice-device-number} | summary} Syntax Description vfc-slot-number Slot number of the VFC. Valid number is from 0 to 11. voice-device-number DSP number.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show vrm vdevices tot tot tot tot tot tot tot ingress control = 1194 ingress data drops = 0 ingress control drops = 0 egress data = 39722 egress control = 1209 egress data drops = 0 egress control drops = 0 slot = 6 virtual voice dev (tag) = 1 channel id = 2 capabilities list map = 9FFF last/current codec loaded/used = None TDM timeslot = 1 Resource (vdev_common) status = 401 means :active others tot ingress data = 21 tot ingress control = 1167 tot i
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show vrm vdevices Table 69 show vrm vdevices Field Descriptions (continued) Field Description capability list map Bitmaps for the codec supported on that DSP channel.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show vrm vdevices Table 69 show vrm vdevices Field Descriptions (continued) Field Description Resource (vdev_common) status Current status of the VFC.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show vrm vdevices *********************************************************** ******summary of voice devices for all voice cards********* *********************************************************** slot = 6 major ver = 0 minor ver = 1 core type used = 2 number of modules = 16 number of voice devices (DSPs) = 96 chans per vdevice = 2 tot chans = 192 tot active calls = 178 module presense bit map = FFFF tdm mode = 1 num_of_tdm_timeslots = 384 auto recove
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show vrm vdevices Table 70 show vrm vdevices summary Field Descriptions (continued) Field Description core type used Type of DSPware in use. Possible field values are: • 1 = UBL (boot loader) • 2 = high complexity core • 3 = medium complexity core • 4 = low complexity core • 255 = invalid number of modules Number of modules on the VFC. Maximum is 16. number of voice devices (DSP)s Number of possible DSPs. Maximum number is 96.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show vrm vdevices Table 70 show vrm vdevices summary Field Descriptions (continued) Field Description built-in codec bitmap Represents the bitmap of the codec built into the DSP firmware.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh show vrm vdevices Table 70 Related Commands show vrm vdevices summary Field Descriptions (continued) Field Description fax codec bitmap Represents the fax codec bitmap. Possible field values are: FAX_NONE = 0x1 • FAX_VOICE = 0x2 • FAX_144 = 0x4 • FAX_96 = 0x8 • FAX_72 = 0x10 • FAX_48 = 0x20 • FAX_24 = 0x40 Logical Device (Tag) Tag number or DSP number on that VFC.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh shut shut To shut down a set of digital signal processors (DSPs) on the Cisco 7200 series router, use the shut command in DSP configuration mode. To put DSPs back in service, use the no form of this command. shut number no shut number Syntax Description number Defaults no shut Command Modes DSP configuration Command History Release Modification 12.0(5)XE This command was introduced on the Cisco 7200 series router. 12.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh shutdown (dial-peer) shutdown (dial-peer) To change the administrative state of the selected dial peer from up to down, use the shutdown command in dial-peer configuration mode. To change the administrative state of this dial peer from down to up, use the no form of this command. shutdown no shutdown Syntax Description This command has no arguments or keywords.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh shutdown (DS1) shutdown (DS1) To shut down a DS1 link (send a Blue Alarm), use the shutdown command in controller configuration mode. To activate the DS1 (cancel the sending of the Blue Alarm), use the no form of the command. shutdown no shutdown Syntax Description This command has no arguments or keywords. Defaults no shutdown Command Modes Controller configuration Command History Release Modification 11.3(1)MA This command was introduced.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh shutdown (gatekeeper) shutdown (gatekeeper) To disable the gatekeeper, use the shutdown command in gatekeeper configuration mode. To enable the gatekeeper, use the no form of this command. shutdown no shutdown Syntax Description This command has no arguments or keywords. Defaults Disabled (shut down) Command Modes gatekeeper configuration Command History Release Modification 11.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh shutdown (RLM) shutdown (RLM) To shut down all of the links under the RLM group, use the shutdown command in RLM configuration mode. RLM will not try to reestablish those links until the command is negated. To disable this function, use the no form of this command. shutdown no shutdown Syntax Description This command has no arguments or keywords. Defaults Disabled Command Modes RLM configuration Command History Release Modification 11.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh shutdown (settlement) shutdown (settlement) To deactivate the settlement provider, use the shutdown command in settlement configuration mode. To activate a settlement provider, use the no shutdown command shutdown no shutdown Syntax Description This command has no arguments or keywords. Defaults The default status of a settlement provider is deactivated. The settlement provider is down.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh shutdown (settlement) Command Description response-timeout Configures the maximum time to wait for a response from a server. retry-delay Sets the time between attempts to connect with the settlement provider. session-timeout Sets the interval for closing the connection when there is no input or output traffic. settlement Enters settlement configuration mode and specifies the attributes specific to a settlement provider.
Cisco IOS Voice, Video, and Fax Commands: R Through Sh shutdown (voice-port) shutdown (voice-port) To take the voice ports for a specific voice interface card offline, use the shutdown command in voice-port configuration mode. To put the ports back in service, use the no form of this command. shutdown no shutdown Syntax Description This command has no arguments or keywords. Defaults shutdown Command Modes Voice-port configuration Command History Release Modification 11.
