User manual
Table Of Contents
- Cisco Aironet 1130AG Series Access Point Hardware Installation Guide
- Contents
- Preface
- Overview
- Installing the Access Point
- Safety Information
- Warnings
- Unpacking the Access Point
- Basic Installation Guidelines
- Controller Discovery Process for Lightweight Access Points
- Deploying the Access Points on the Wireless Network
- Opening the Access Point Cover
- Mounting the Access Point on a Horizontal Surface
- Mounting the Access Point Below a Suspended Ceiling
- Mounting the Access Point Above a Suspended Ceiling
- Mounting Access Point on a Network Cable Box
- Mounting Access Point on a Desktop or Shelf
- Attaching the Access Point to the Mounting Plate
- Securing the Access Point
- Connecting the Ethernet and Power Cables
- Rotating the Cisco Logo
- Troubleshooting Autonomous Access Points
- Checking the Autonomous Access Point LEDs
- Checking Basic Settings
- Low Power Condition for Autonomous Access Points
- Running the Carrier Busy Test
- Running the Ping Test
- Resetting to the Default Configuration
- Reloading the Access Point Image
- Obtaining the Access Point Image File
- Connecting to the Access Point Console Port
- Obtaining the TFTP Server Software
- Troubleshooting Lightweight Access Points
- Guidelines for Using 1130AG Series Lightweight Access Points
- Checking the Lightweight Access Point LEDs
- Low Power Condition for Lightweight Access Points
- Manually Configuring Controller Information Using the Access Point CLI
- Returning the Access Point to Autonomous Mode
- Obtaining the Autonomous Access Point Image File
- Connecting to the Access Point Console Port
- Obtaining the TFTP Server Software
- Translated Safety Warnings
- Declarations of Conformity and Regulatory Information
- Manufacturers Federal Communication Commission Declaration of Conformity Statement
- VCCI Statement for Japan
- Industry Canada
- European Community, Switzerland, Norway, Iceland, and Liechtenstein
- Declaration of Conformity for RF Exposure
- Guidelines for Operating Cisco Aironet Access Points in Japan
- Administrative Rules for Cisco Aironet Access Points in Taiwan
- Declaration of Conformity Statements
- Access Point Specifications
- Channels and Maximum Power Levels
- Console Cable Pinouts
- Priming Lightweight Access Points Prior to Deployment
- Configuring DHCP Option 43 for Lightweight Access Points
- Glossary
- Index
Contents
iv
Cisco Aironet 1130AG Series Access Point Hardware Installation Guide
OL-8369-05
Warnings 2-2
Unpacking the Access Point 2-3
Package Contents 2-3
Basic Installation Guidelines 2-4
Controller Discovery Process for Lightweight Access Points 2-4
Deploying the Access Points on the Wireless Network 2-5
Access Point Layout and Connectors 2-6
Mounting Plate 2-7
Suspended Ceiling Adjustable T-Rail Clips 2-8
Opening the Access Point Cover 2-11
Mounting the Access Point on a Horizontal Surface 2-12
Mounting the Access Point Below a Suspended Ceiling 2-13
Mounting the Access Point Above a Suspended Ceiling 2-14
Mounting Access Point on a Network Cable Box 2-16
Mounting Access Point on a Desktop or Shelf 2-16
Attaching the Access Point to the Mounting Plate 2-16
Securing the Access Point 2-18
Using a Security Cable 2-18
Securing the Access Point to the Mounting Plate 2-19
Connecting the Ethernet and Power Cables 2-21
Connecting to an Ethernet Network with an Inline Power Source 2-22
Connecting to an Ethernet Network with Local Power 2-23
Rotating the Cisco Logo 2-24
CHAPTER
3 Troubleshooting Autonomous Access Points 3-1
Checking the Autonomous Access Point LEDs 3-2
Checking Basic Settings 3-4
Default IP Address Behavior 3-4
Default SSID and Radio Behavior 3-4
Enable Radio Interfaces 3-5
SSID 3-5
WEP Keys 3-5
Security Settings 3-5
Low Power Condition for Autonomous Access Points 3-6
Intelligent Power Management 3-6
Inline Power Status Messages 3-7
Configuring Power Using the CLI 3-10
Issuing the Cisco IOS Command Using the CLI 3-11