Voice Gateway with Router User Guide Voice Model No.
Voice Gateway with Router Copyright and Trademarks Specifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Copyright © 2006 Cisco Systems, Inc. All rights reserved. Other brands and product names are trademarks or registered trademarks of their respective holders.
Voice Gateway with Router
Voice Gateway with Router Table of Contents Chapter 1: Introduction Welcome What’s in this Guide? Chapter 2: Networking Basics An Introduction to Local Area Networks The Use of IP Addresses Chapter 3: Getting to Know the Voice Gateway The Back Panel The Front Panel Chapter 4: Getting Started Before You Begin Connecting the Voice Gateway Configuring the Voice Gateway Chapter 5: Using the Interactive Voice Response Menu Overview Accessing the Interactive Voice Response Menu Using the Interactive Voice Re
Voice Gateway with Router Appendix A: Troubleshooting Common Problems and Solutions Frequently Asked Questions Appendix B: Finding the MAC Address and IP Address for Your Ethernet Adapter Windows 98 or Me Instructions Windows 2000 or XP Instructions For the Voice Gateway’s Web-based Utility Appendix C: Windows Help Appendix D: Glossary Appendix E: Specifications Appendix F: Warranty Information Appendix G: Regulatory Information Appendix H: Contact Information Internet Telephony Service Provider (ITSP) L
Voice Gateway with Router List of Figures Figure 3-1: Back Panel Figure 3-2: Front Panel Figure 4-1: Connect to the Telephone Wall Jack Figure 4-2: Connect a Telephone Figure 4-3: Connect a PC Figure 4-4: Connect to the Modem Figure 4-5: Connect Power Figure 4-6: Login Screen Figure 4-7: Router - WAN Setup Screen Figure 4-8: MAC Clone Settings Figure 4-9: Static IP Settings Figure 4-10: PPPoE Settings Figure 6-1: Login Screen Figure 6-2: Router - Status Screen Figure 6-3: Router - WAN Setup Screen Figure 6
Voice Gateway with Router Figure 6-12: Voice - User 1 Screen Figure 6-13: Speed Dial and Supplementary Service Settings Figure 6-14: Distinctive Ring and Ring Settings Figure 6-15: Voice - PSTN User Screen Figure 6-16: PSTN-To-VoIP Speed Dial Settings Figure 6-17: PSTN Ring Thru Line 1 Distinctive Ring Settings Figure 6-18: PSTN Ring Thru Line 1 Ring Settings Figure B-1: IP Configuration Screen Figure B-2: MAC/Adapter Address Figure B-3: MAC/Physical Address Figure B-4: MAC Address Cloning 40 42 43 45 46
Voice Gateway with Router Chapter 1: Introduction Welcome Thank you for choosing the Voice Gateway with Router. This Voice Gateway will allow your computers to share a high-speed Internet connection as well as resources, including files and printers. Plus, the Voice Gateway can bridge traditional phone service, also known as Public Switched Telephone Network (PSTN) service, with Internet phone service, also known as Voice over Internet Protocol (VoIP).
Voice Gateway with Router To create your network, install and set up the Voice Gateway. To guide you through the process, use the instructions in the Quick Installation or this User Guide to help you. These instructions should be all you need to get the most out of the Voice Gateway. What’s in this Guide? This guide covers the basic steps for setting up a network with the Voice Gateway.
Voice Gateway with Router • Appendix A: Troubleshooting This appendix describes some possible problems and solutions, as well as frequently asked questions, regarding installation and use of the Voice Gateway. • Appendix B: Finding the MAC Address and IP Address for Your Ethernet Adapter This appendix instructs you on how to find the MAC address or Ethernet address of your PC’s Ethernet network adapter.
Voice Gateway with Router 4 Chapter 1: Introduction What’s in this Guide?
Voice Gateway with Router Chapter 2: Networking Basics An Introduction to Local Area Networks Simply put, a router is a network device that connects two networks together. The Voice Gateway connects your local area network (LAN), or the group of PCs in your home or office, to the Internet. The Voice Gateway processes and regulates the data that travels between these two networks.
Voice Gateway with Router If you use the Voice Gateway to share your cable or DSL Internet connection, contact your ISP to find out if they have assigned a static IP address to your account. If so, you will need that static IP address when configuring the Voice Gateway. You can get the information from your ISP. A dynamic IP address is automatically assigned to a device on the network. These IP addresses are called dynamic because they are only temporarily assigned to the PC or other device.
Voice Gateway with Router Chapter 3: Getting to Know the Voice Gateway The Back Panel The Voice Gateway’s ports are located on the back panel. Figure 3-1: Back Panel LINE Use this port to connect the Voice Gateway to your standard telephone wall jack. PHONE Use this port to connect an analog phone (or fax machine) with an RJ-11 telephone cable. ETHERNET The ETHERNET port connects to a network device, such as a PC or a switch, with an Ethernet network cable.
Voice Gateway with Router The Front Panel The Voice Gateway’s LEDs, which inform you about network activities, are located on the front panel. Figure 3-2: Front Panel Power Green. The Power LED lights up when the Voice Gateway is powered on and connected to the Internet. It flashes when the Voice Gateway is not connected to the Internet. The LED also flashes when the Voice Gateway is booting up or upgrading its firmware. ETHERNET Green.
Voice Gateway with Router Chapter 4: Getting Started Before You Begin Make sure you have the following: • An active Internet connection • An active Internet phone service account and its settings • cable/DSL modem • One computer for configuration of the Voice Gateway • Analog telephone or fax machine with an RJ-11 phone cable Connecting the Voice Gateway 1. Power off your network devices, including your modem and PC. 2.
Voice Gateway with Router 4. Connect one end of an Ethernet network cable (included) to the ETHERNET port of the Voice Gateway. Connect the other end to the Ethernet port of your PC. 5. Connect one end of a different Ethernet network cable to the INTERNET port of the Voice Gateway. Connect the other end to your cable/DSL modem. 6. Power on the broadband modem. Figure 4-3: Connect a PC 7.
Voice Gateway with Router Configuring the Voice Gateway 1. Launch the web browser on the PC. 2. Enter 192.168.0.1/advanced in the Address field (192.168.0.1 is the default local IP address of the Voice Gateway). Then press the Enter key. 3. If your Internet Telephony Service Provider (ITSP) did not supply a password, you will not see a login screen. Proceed to step 4. Figure 4-6: Login Screen If your ITSP supplied a password, you will see a login screen.
Voice Gateway with Router Static IP a. Select Static IP from the Connection Type drop-down menu. b. In the Static IP Settings section, enter the IP address in the Static IP field, the subnet mask in the NetMask field, and the default gateway IP address in the Gateway field. c. In the Optional Settings section, enter the DNS server address(es) in the Primary DNS and optional Secondary DNS fields. d. Click the Submit All Changes button.
Voice Gateway with Router Chapter 5: Using the Interactive Voice Response Menu Overview NOTE: If your ITSP sent you the Voice Gateway, then it may be pre-configured for you, and you do not need to change any settings. Refer to the instructions supplied by your service provider for more information. You may need to manually configure the Voice Gateway by entering the settings provided by your Internet Telephony Service Provider (ITSP).
Voice Gateway with Router Using the Interactive Voice Response Menu While entering a value, such as an IP address, you may exit without entering any changes. Press the * (star) key twice within half a second. Otherwise, the * will be treated as a decimal point or dot. After entering a value, such as an IP address, press the # (pound) key to indicate you have finished your selection. To save the new setting, press 1. To review the new setting, press 2. To re-enter the new setting, press 3.
Voice Gateway with Router The settings you have saved will take effect after you have hung up the telephone. The Voice Gateway may reboot at this time. Interactive Voice Response Menu Action Command (press these keys on the telephone) Choices Enter Interactive Voice Response Menu **** Use this command to enter the Interactive Voice Response Menu. Do not press any other keys until you hear, “Linksys configuration menu. Please enter the option followed by the # (pound) key or hang up to exit.
Voice Gateway with Router Interactive Voice Response Menu Action Command (press these keys on the telephone) Check Firmware Version 150 Hear the version number of the firmware currently running on the Voice Gateway. Check Primary DNS Server IP Address 160 Hear the IP address of the primary DNS (Domain Name Service) server. Check Internet Web Server Port 170 Hear the port number of the Internet Web server used for the Web-based Utility.
Voice Gateway with Router Interactive Voice Response Menu Action Command (press these keys on the telephone) Choices Description Set Network (or Subnet) Mask 121 Enter the network or subnet mask using numbers on the telephone keypad. Use the * (star) key when entering a decimal point. First, set the Internet Connection Type to static IP address; otherwise, you will hear, “Invalid Option,” if you try to set the network or subnet mask.
Voice Gateway with Router Interactive Voice Response Menu Action Command (press these keys on the telephone) Choices Description Set the Mode 201 Press 0 to select the router/NAT mode. Press 1 to select the bridge/switch mode. If the Voice Gateway acts as the router for your network, use the router/NAT mode. Press 1 to enable. Press 0 to disable. Use this setting to enable or disable WAN access to the Web-based Utility. (This Utility lets you configure the Voice Gateway.
Voice Gateway with Router Interactive Voice Response Menu Action Command (press these keys on the telephone) Choices Description User Factory Reset 877778 Press 1 to confirm. Press * (star) to cancel. The Voice Gateway will request confirmation; enter 1 to confirm. You will hear, “Option successful.” Hang up the phone. The Voice Gateway will reboot and all user-configurable settings will be reset to their factory default settings.
Voice Gateway with Router • To enter P, Q, R, S, o, q, r, or s — press 7. • To enter T, U, V, t, u, or v — press 8. • To enter W, X, Y, Z, w, x, y, or z — press 9. • To enter all other characters, press 0. NOTE: These bulleted instructions only apply when you are entering a password. At all other times, pressing a number only selects a number, not a letter or punctuation mark. For example, to enter the password phone@321 by keypad, press these keys: 746630321.
Voice Gateway with Router Chapter 6: Using the Web-based Utility Overview NOTE: If your ITSP sent you the Voice Gateway, then it may be pre-configured for you, and you do not need to change any settings. Refer to the instructions supplied by your service provider for more information. If you do wish to make changes, follow the instructions in this chapter. The Web-based Utility can be accessed via your web browser through use of a computer on your network.
Voice Gateway with Router Voice • Info. This screen displays voice-related status information about the Voice Gateway. • System. Use this screen to configure the user password. • User 1. Use this screen to configure call forward, speed dial, supplementary service, and ring settings for the Internet phone line. • PSTN User. PSTN stands for Public Switched Telephone Network, which is the network that traditional phone service uses.
Voice Gateway with Router The Router Tab The Router - Status Screen This screen displays product and system information. Product Information Product Name. Shown here is the model number of the Voice Gateway. Serial Number. Shown here is the serial number of the Voice Gateway. Figure 6-2: Router - Status Screen Software Version. Shown here is the version number of the Voice Gateway software. Hardware Version. Shown here is the version number of the Voice Gateway hardware. MAC Address.
Voice Gateway with Router Current IP. Displayed here is the Internet IP address of the Voice Gateway. Host Name. Displayed here is the host name of the Voice Gateway. Domain. Displayed here is the domain name of the Voice Gateway. ip (internet protocol): a protocol used to send data over a network. ip address: the address used to identify a computer or device on a network. Current Netmask. Displayed here is the netmask or subnet mask of the Voice Gateway. Current Gateway.
Voice Gateway with Router The Router - WAN Setup Screen This screen lets you configure the Internet connection, MAC clone, remote management, QoS, VLAN, and optional settings. Information about your Internet connection type should be provided by your Internet Service Provider (ISP). If you do not have this information, contact your service provider. Internet Connection Settings Connection Type. Select the connection type you use: DHCP; Static IP; PPPOE; PPPoE, DHCP; or DHCP, PPPoE.
Voice Gateway with Router PPPoE Service Name (optional). Enter the service name provided by your ISP. Optional Settings HostName. Enter the host name, if provided by your ISP. Domain. Enter the domain name, if provided by your ISP. Primary DNS. Enter the IP address of the primary DNS server. Secondary DNS (optional). Enter the IP address of the secondary DNS server. MAC Clone Settings Enable MAC Clone Service. Select whether you want to clone a MAC address onto the Voice Gateway, yes or no.
Voice Gateway with Router Maximum Uplink Speed. Enter the maximum upload speed of your Internet connection. The default is 128Kbps. VLAN (Virtual Local Area Network) Settings Enable VLAN. VLAN (802.1Q) settings let you use the Voice Gateway in a virtual LAN environment. Select yes or no from the drop-down menu. The default is no. VLAN ID. Enter the ID number used by the Voice Gateway. The default is 1.
Voice Gateway with Router The Router - LAN Setup Screen This screen lets you configure the local network, dynamic DHCP, and static DHCP lease settings. Networking Service. Select the service you want to use, NAT or Bridge. The default is NAT. LAN Network Settings LAN IP Address. Enter the local IP address of the Voice Gateway. The default is 192.168.0.1. LAN Subnet Mask. Select the local subnet mask: 255.255.255.0, 255.255.255.128, 255.255.255.192, 255.255.255.224, 255.255.255.240, 255.255.255.
Voice Gateway with Router Host MAC Address. Enter the MAC address of the device whose IP address you want to specify. Host IP Address. Enter the IP address you want to assign to the device, 192.168.0.x (x being a different number for each device you specify). When you have finished making changes, click the Submit All Changes button to save the changes, or click the Undo All Changes button to undo your changes.
Voice Gateway with Router The Router - Application Screen This screen lets you configure port forwarding, DMZ, and reserved ports range settings. Port Forwarding Settings Enable. Select yes or no for each port forwarding entry, which defines a port range to be forwarded to a server. The default is no. Service Name. Enter the name of the service or application. Starting Port. Enter the starting port number of the forwarded port range. Ending Port. Enter the ending port number of the forwarded port range.
Voice Gateway with Router Miscellaneous Settings Multicast Passthru. Multicasting allows for multiple transmissions to specific recipients at the same time. If multicasting is permitted, then the Voice Gateway will allow IP multicast packets to be forwarded to the appropriate computers. Select the types of multicast transmissions to allow: Disabled (none), Inbound Only, Outbound Only, or Inbound and Outbound. The default is Disabled. System Reserved Ports Range Starting Port.
Voice Gateway with Router The Voice Tab The Voice - Info Screen This screen shows voice-related settings for the Voice Gateway. Product Information Product Name. Shown here is the model number of the Voice Gateway. Serial Number. Shown here is the serial number of the Voice Gateway. Software Version. Shown here is the version number of the Voice Gateway software. Hardware Version. Shown here is the version number of the Voice Gateway hardware. MAC Address.
Voice Gateway with Router RTP Bytes Sent. Displayed here is the number of RTP bytes sent by the Voice Gateway. RTP Packets Recv. Displayed here is the number of RTP packets received by the Voice Gateway. RTP Bytes Recv. Displayed here is the number of RTP bytes received by the Voice Gateway. SIP Messages Sent. Displayed here is the number of SIP messages sent by the Voice Gateway. SIP Bytes Sent. Displayed here is the number of SIP bytes sent by the Voice Gateway. SIP Messages Recv.
Voice Gateway with Router Last Called Number. Displayed here is the last number called. Last Caller Number. Displayed here is the number of the last caller. Mapped SIP Port. Shown here is the port number of the NAT mapped SIP port. Calls 1 and 2 have the same status information available. Call 1/2 State. Displayed here is the status of the call. Call 1/2 Tone. Displayed here is the type of tone used by the call. Call 1/2 Encoder. Displayed here is the codec used for encoding. Call 1/2 Decoder.
Voice Gateway with Router Call 1/2 Packets Recv. Displayed here is the number of packets received. Call 1/2 Bytes Sent. Displayed here is the number of bytes sent. Call 1/2 Bytes Recv. Displayed here is the number of bytes received. Call 1/2 Decode Latency. Displayed here is the number of milliseconds for decoder latency. Call 1/2 Jitter. Displayed here is the number of milliseconds for receiver jitter. Call 1/2 Round Trip Delay. Displayed here is the number of milliseconds for delay. Call 1/2 Packets Lost.
Voice Gateway with Router Next Registration In. Shown here is the number of seconds until the next registration. Last Called VoIP Number. VoIP stands for Voice over Internet Protocol, which is used by Internet phone calls. Displayed here is the last Internet phone number called from the landline. Last Called PSTN Number. Displayed here is the last landline number dialed by the Voice Gateway. Last VoIP Caller.
Voice Gateway with Router VoIP Peer Name. Displayed here is the name of the party at the VoIP call leg. PSTN Peer Name. Displayed here is the name of the party at the PSTN call leg. VoIP Peer Number. Displayed here is the phone number of the party at the VoIP call leg. PSTN Peer Number. Displayed here is the phone number of the party at the PSTN call leg. The following are the same as the status information for Line 1, Call 1 in the Line 1 Status section. VoIP Call Encoder.
Voice Gateway with Router VoIP Call Round Trip Delay. Displayed here is the number of milliseconds for delay. VoIP Call Packets Lost. Displayed here is the number of packets lost. VoIP Call Packet Error. Displayed here is the number of invalid packets received. VoIP Call Mapped RTP Port. Displayed here is the number of the NAT mapped RTP port. When you have finished making changes, click the Submit All Changes button to save the changes, or click the Undo All Changes button to undo your changes.
Voice Gateway with Router The Voice - System Screen This screen lets you change the password for user access to the Web-based Utility. NOTE: If your ITSP supplied this password, you may not be able to change it. Figure 6-11: Voice - System Screen System Configuration User Password. Enter the password for the user. (By default, there is no password.) When you have finished making your change, click the Submit All Changes button to save the changes, or click the Undo All Changes button to undo your change.
Voice Gateway with Router The Voice - User 1 Screen This screen lets you configure the settings for the Internet phone line. Call Forward Settings Enter the call forwarding numbers you want to use. Cfwd All Dest. Enter the number for the Call Forward All Service feature (when you want to forward all calls). Cfwd Busy Dest. Enter the number for the Call Forward Busy feature (when the line is busy). Cfwd No Ans Dest. Enter the number for the Call Forward No Answer feature (when the line is not answered).
Voice Gateway with Router Cfwd Sel3 Dest. Enter the forward number for the Call Forward Selective 3 feature. Cfwd Sel4 Caller. Enter the caller number pattern to trigger the Call Forward Selective 4 feature. Cfwd Sel4 Dest. Enter the forward number for the Call Forward Selective 4 feature. Cfwd Sel5 Caller. Enter the caller number pattern to trigger the Call Forward Selective 5 feature. Cfwd Sel5 Dest. Enter the forward number for the Call Forward Selective 5 feature. Cfwd Sel6 Caller.
Voice Gateway with Router Speed Dial Settings Speed Dial 2. Enter the target phone number (or URL) to assign to speed dial 2. Speed Dial 3. Enter the target phone number (or URL) to assign to speed dial 3. Speed Dial 4. Enter the target phone number (or URL) to assign to speed dial 4. Figure 6-13: Speed Dial and Supplementary Service Settings Speed Dial 5. Enter the target phone number (or URL) to assign to speed dial 5. Speed Dial 6. Enter the target phone number (or URL) to assign to speed dial 6.
Voice Gateway with Router CWCID Setting. Select whether you want to enable caller ID for call waiting, yes or no. The default is yes. Dist Ring Setting. Select whether you want to use the distinctive ring feature, yes or no. The default is yes. Message Waiting. Select whether you want to use the message waiting feature, yes or no. The default is no. Distinctive Ring Settings Ring1 Caller. Enter the caller number pattern to play Distinctive Ring/Call Waiting Tone (CWT) 1. Ring2 Caller.
Voice Gateway with Router Hold Reminder Ring. Select the ring pattern that will remind you of a call on hold when the phone is on-hook. Call Back Ring. Select the ring pattern for call back notification. Cfwd Ring Splash Len. Enter the duration of the ring splash when a call is forwarded. The range is 0 to 10.0 seconds. Cblk Ring Splash Len. Enter the duration of the ring splash when a call is blocked. The range is 0 to 10.0 seconds. VMWI Ring Splash Len.
Voice Gateway with Router The Voice - PSTN User Screen This screen lets you configure the settings for the LINE port service, which can be a PSTN service or a second VoIP service. PSTN-To-VoIP Selective Call Forward Settings Enter the landline caller numbers that will be forwarded to specific Internet phone numbers. Cfwd Sel1 Caller. Enter the caller number pattern that will be forwarded to the Cfwd Sel1 Dest number. Cfwd Sel1 Dest. Enter the forward number for the Cfwd Sel1 Caller.
Voice Gateway with Router Cfwd Sel5 Dest. Enter the forward number for the Cfwd Sel5 Caller. If this is blank, then the landline caller is blocked for Internet phone service. Cfwd Sel6 Caller. Enter the caller number pattern that will be forwarded to the Cfwd Sel6 Dest number. Cfwd Sel6 Dest. Enter the forward number for the Cfwd Sel6 Caller. If this is blank, then the landline caller is blocked for Internet phone service. Cfwd Sel7 Caller.
Voice Gateway with Router Speed Dial 6. Enter the target phone number to assign to speed dial 6. Speed Dial 7. Enter the target phone number to assign to speed dial 7. Speed Dial 8. Enter the target phone number to assign to speed dial 8. Speed Dial 9. Enter the target phone number to assign to speed dial 9. PSTN Ring Thru Line 1 Distinctive Ring Settings Enter the landline caller numbers that will trigger the corresponding ring tones for Line 1. Ring1 Caller.
Voice Gateway with Router PSTN Ring Thru Line 1 Ring Settings This ring tone will be used to ring through Line 1. Default Ring. Select the default ringing pattern for all callers. If you select Follow Line 1, then the ring selection will be determined by Line 1’s distinctive ring settings. Figure 6-18: PSTN Ring Thru Line 1 Ring Settings When you have finished making your change, click the Submit All Changes button to save the changes, or click the Undo All Changes button to undo your change.
Voice Gateway with Router Appendix A: Troubleshooting This appendix provides solutions to problems that may occur during the installation and operation of the Voice Gateway. Read the description below to solve your problems. If you can't find an answer here, check the website of your Internet Telephony Service Provider (ITSP) or the Linksys website at www.linksys.com. Common Problems and Solutions 1. I don’t hear a dial tone, and the PHONE LED is not lit.
Voice Gateway with Router C. Click Tools. Click Internet Options. Click the Security tab. Click the Default level button. Make sure the security level is Medium or lower. Then click the OK button. 3. I need to set a static IP address on a PC. The Voice Gateway, by default, assigns an IP address range of 192.168.0.100 to 192.168.0.150 using the DHCP server on the Voice Gateway. To set a static IP address, you can only use the ranges 192.168.0.2 to 192.168.0.99 and 192.168.0.151 to 192.168.0.254.
Voice Gateway with Router For Windows 2000: A. Click Start, Settings, and Control Panel. Double-click Network and Dial-Up Connections. B. Right-click the Local Area Connection that is associated with the Ethernet adapter you are using, and select the Properties option. C. In the Components checked are used by this connection box, highlight Internet Protocol (TCP/IP), and click the Properties button. Select Use the following IP address option. D.
Voice Gateway with Router D. In the This connection uses the following items box, highlight Internet Protocol (TCP/IP). Click the Properties button. E. Enter a unique IP address that is not used by any other computer on the network connected to the Voice Gateway. You can only use an IP address in the ranges 192.168.0.2 to 192.168.0.99 and 192.168.0.151 to 192.168.0.254. F. Enter the Subnet Mask, 255.255.255.0. G. Enter the Default Gateway, 192.168.0.1 (Voice Gateway’s default IP address). H.
Voice Gateway with Router 4. Click the OK button in the Internet Protocol (TCP/IP) Properties window, and click the OK button in the Local Area Connection Properties window. 5. Restart the computer if asked. 6. Click the OK button in the Internet Protocol (TCP/IP) Properties window, and click the OK button in the Local Area Connection Properties window. 7. Restart the computer if asked. For Windows XP: The following instructions assume you are running Windows XP with the default interface.
Voice Gateway with Router • If you do NOT get a reply, check the cable, and make sure Obtain an IP address automatically is selected in the TCP/IP settings for your Ethernet adapter. D. In the command prompt, type ping followed by your Internet IP address and press the Enter key. The Internet IP Address can be found in the web interface of the Voice Gateway. For example, if your Internet IP address is 1.2.3.4, you would enter ping 1.2.3.4 and press the Enter key.
Voice Gateway with Router E. Make sure the cable connecting from your cable or DSL modem is connected to the Voice Gateway’s Internet port. Verify that the Router - Status page of the Voice Gateway’s Web-based Utility shows a valid IP address from your ISP. F. Turn off the computer, Voice Gateway, and cable/DSL modem. Wait 30 seconds, and then turn on the Voice Gateway, cable/DSL modem, and computer. Check the Router - Status page of the Voice Gateway’s Web-based Utility to see if you get an IP address. 6.
Voice Gateway with Router D. Enter the port range of the service you are using. For example, if you have a web server, you would enter the range 80 (in the Starting Port field) to 80 (in the Ending Port field). E. Select the protocol you will be using, TCP or UDP, or select Both. F. Enter the IP address of the PC or network device that you want the port server to go to. For example, if the web server’s Ethernet adapter IP address is 192.168.0.100, you would enter 100 in the field provided.
Voice Gateway with Router information on what port services to use is to go to the website of the online game or application you want to use. Follow these steps to set up online game hosting or use a certain Internet application: A. Access the Voice Gateway’s Web-based Utility by going to http://192.168.0.1 or the IP address of the Voice Gateway. Go to the Router => Application tab. B. Select yes from the Enable drop-down menu. C. Enter any name you want to use for the service. D.
Voice Gateway with Router 9. I can’t get the Internet game, server, or application to work. If you are having difficulties getting any Internet game, server, or application to function properly, consider exposing one PC to the Internet using DeMilitarized Zone (DMZ) hosting. This option is available when an application requires too many ports or when you are not sure which port services to use.
Voice Gateway with Router For Microsoft Internet Explorer 5.0 or higher: A. B. C. D. E. Click Start, Settings, and Control Panel. Double-click Internet Options. Click the Connections tab. Click the LAN settings button and remove anything that is checked. Click the OK button to go back to the previous screen. Click the option Never dial a connection. This will remove any dial-up pop-ups for PPPoE users. For Netscape 4.7 or higher: A.
Voice Gateway with Router Frequently Asked Questions Can I make calls if my Internet connection is down? When you make Internet phone calls, your high-speed Internet connection must be active. However, you can make calls using your landline. Can I make calls while I’m browsing the Internet? Yes. You can make calls while browsing the Internet. However, your web browsing may affect the quality of your Internet calls, depending on the amount of upstream data traffic passing through your Internet connection.
Voice Gateway with Router accounts, such as DSL or cable modems, when only one TCP/IP address is provided by the ISP. The user may have many private addresses behind this single address provided by the ISP. Does the Voice Gateway support any operating system other than Windows 98, Millennium, 2000, or XP? Yes, but Linksys does not, at this time, provide technical support for setup, configuration or troubleshooting of any non-Windows operating systems.
Voice Gateway with Router How do I get Half-Life: Team Fortress to work with the Voice Gateway? The default client port for Half-Life is 27005. The computers on your LAN need to have “+clientport 2700x” added to the HL shortcut command line; the x would be 6, 7, 8, and on up. This lets multiple computers connect to the same server. One problem: Version 1.0.1.6 won’t let multiple computers with the same CD key connect at the same time, even if on the same LAN (not a problem with 1.0.1.3).
Voice Gateway with Router Navigator, click Edit, Preferences, Advanced, and Proxy. Make sure that Netscape Navigator is set to Direct connection to the Internet. What is DMZ Hosting? Demilitarized Zone (DMZ) allows one IP address (computer) to be exposed to the Internet. Some applications require multiple TCP/IP ports to be open. It is recommended that you set your computer with a static IP if you want to use DMZ Hosting.
Voice Gateway with Router 64 Appendix A: Troubleshooting Frequently Asked Questions
Voice Gateway with Router Appendix B: Finding the MAC Address and IP Address for Your Ethernet Adapter This section describes how to find the MAC address for your computer’s Ethernet adapter so you can use the MAC address cloning feature of the Voice Gateway. You can also find the IP address of your computer’s Ethernet adapter. This IP address is used for the Voice Gateway’s forwarding and/or DMZ features.
Voice Gateway with Router Windows 2000 or XP Instructions 1. Click Start and Run. In the Open field, enter cmd. Press the Enter key or click the OK button. 2. At the command prompt, enter ipconfig /all. Then press the Enter key. 3. Write down the Physical Address as shown on your computer screen; it is the MAC address for your Ethernet adapter. This appears as a series of numbers and letters. The MAC address/Physical Address is what you will use for MAC address cloning.
Voice Gateway with Router Appendix C: Windows Help Almost all Linksys products require Microsoft Windows. Windows is the most used operating system in the world and comes with many features that help make networking easier. These features can be accessed through Windows Help and are described in this appendix. TCP/IP Before a computer can communicate with a network router, TCP/IP must be enabled. TCP/IP is a set of instructions, or protocol, all PCs follow to communicate over a network.
Voice Gateway with Router 68 Appendix C: Windows Help
Voice Gateway with Router Appendix D: Glossary This glossary contains some basic networking terms you may come across when using this product. For more advanced terms, see the complete Linksys glossary at http://www.linksys.com/glossary. Bandwidth - The transmission capacity of a given device or network. Bit - A binary digit. Boot - To start a device and cause it to start executing instructions. Broadband - An always-on, fast Internet connection.
Voice Gateway with Router DNS (Domain Name Server) - The IP address of your ISP's server, which translates the names of websites into IP addresses. Domain - A specific name for a network of computers. Download - To receive a file transmitted over a network. DSL (Digital Subscriber Line) - An always-on broadband connection over traditional phone lines. Dynamic IP Address - A temporary IP address assigned by a DHCP server. Encryption - Encoding data transmitted in a network.
Voice Gateway with Router IPCONFIG - A Windows 2000 and XP utility that displays the IP address for a particular networking device. ISP (Internet Service Provider) - A company that provides access to the Internet. LAN - The computers and networking products that make up your local network. MAC (Media Access Control) Address - The unique address that a manufacturer assigns to each networking device. Mbps (MegaBits Per Second) - One million bits per second; a unit of measurement for data transmission.
Voice Gateway with Router Server - Any computer whose function in a network is to provide user access to files, printing, communications, and other services. SMTP (Simple Mail Transfer Protocol) - The standard e-mail protocol on the Internet. SNMP (Simple Network Management Protocol) - A widely used network monitoring and control protocol. Static IP Address - A fixed address assigned to a computer or device that is connected to a network. Static Routing - Forwarding data in a network via a fixed path.
Voice Gateway with Router Appendix E: Specifications Model SPA3102 Data Networking MAC Address (IEEE 802.
Voice Gateway with Router Voice Gateway Voice Algorithms Fax Capability 74 SIPv2: Session Initiation Protocol v2 (RFC 3261, 3262, 3263, 3264) SIP Proxy Redundancy - Dynamic via DNS SRV, A Records Re-registration with Primary SIP Proxy Server SIP Support in Network Address Translation Networks - NAT (incl. STUN) Secure (Encrypted) Calling via Pre-Standard Implementation of Secure RTP Codec Name Assignment G.711 (A-law and µ-law) G.726 (16/24/32/40 kbps) G.729 A G.723.1 (6.3 kbps, 5.
Voice Gateway with Router VMWI - via FSK Polarity Control Hook Flash Event Signaling Caller ID Generation (Name & Number) - Bellcore, DTMF, ETSI Music on Hold Client Streaming Audio Server - up to 10 sessions Security Password Protected System Reset to Factory Default Password Protected Admin and User Access Authority Provisioning/Configuration/Authentication: HTTPS with Factory Installed Client Certificate HTTP Digest - Encrypted Authentication via MD5 (RFC 1321) Up to 256-bit AES Encryption Provisionin
Voice Gateway with Router Physical Interfaces 2 100baseT RJ-45 Ethernet Port (IEEE 802.
Voice Gateway with Router Documentation Quick Installation and Compliance Guide User Guide Administration Guide - Service Providers Only Provisioning Guide - Service Providers Only Dimensions (W x H x D) 3.98" x 3.98" x 1.10" (101 x 101 x 28 mm) Unit Weight 5.11 oz. (0.145 kg) Operating Temp. 32 to 113º F (0 to 45º C) Storage Temp.
Voice Gateway with Router 78 Appendix E: Specifications
Voice Gateway with Router Appendix F: Warranty Information This Warranty is valid and may be processed only in the country of purchase. Contact your service provider if the warranty support issues are to be handled by them as per your service agreements. Linksys warrants to You that, for a period of two years (the “Warranty Period”), your Linksys Product will be substantially free of defects in materials and workmanship under normal use.
Voice Gateway with Router provided under this Agreement fails of its essential purpose. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to You. Please direct all inquiries to: Linksys, P.O. Box 18558, Irvine, CA 92623.
Voice Gateway with Router Appendix G: Regulatory Information FCC Statement This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Voice Gateway with Router The REN is useful to determine the quantity of devices that may be connected to the telephone line and still have all of those devices ring when your telephone number is called. In most, but not all areas, the sum of RENs should not exceed 5. To be certain of the number of devices that may be connected to the line, as determined by the total RENs, contact the telephone company to determine the maximum REN for the calling area.
Voice Gateway with Router Industry Canada (Canada) This device complies with Industry Canada ICES-003 rule. Cet appareil est conforme à la norme NMB003 d'Industrie Canada.
Voice Gateway with Router User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste Electric and Electronic Equipment (WEEE) This document contains important information for users with regards to the proper disposal and recycling of Linksys products.
Voice Gateway with Router Appendix G: Regulatory Information 85
Voice Gateway with Router 86 Appendix G: Regulatory Information
Voice Gateway with Router Appendix G: Regulatory Information 87
Voice Gateway with Router 88 Appendix G: Regulatory Information
Voice Gateway with Router Appendix H: Contact Information Internet Telephony Service Provider (ITSP) For support, contact your ITSP. Linksys Visit Linksys online for information on the latest products and updates to your existing products at: Appendix H: Contact Information Internet Telephony Service Provider (ITSP) http://www.linksys.
Voice Gateway with Router 90 Appendix H: Contact Information Linksys
www.linksys.
