Cisco AS5350 and Cisco AS5400 Universal Gateway Card Installation Guide Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
C O N T E N T S Preface vii Document Organization vii Document Conventions viii Obtaining Documentation xi World Wide Web xi Documentation CD-ROM xi Ordering Documentation xi Documentation Feedback xi Obtaining Technical Assistance xii Cisco.
Contents Overview 3-3 Removing the T1 or E1 DFC 3-3 Installing the T1 or E1 DFC 3-9 Configuring Input Impedance for the E1 DFC Configuration 3-11 Verification 3-11 Getting Help 3-14 Where to Go Next CHAPTER 4 T3 Dial Feature Card Overview 3-11 3-14 4-1 4-1 Online Installation and Removal (OIR) of the T3 DFC Overview 4-2 Removing the T3 DFC 4-2 Installing the T3 DFC 4-5 Getting Help 4-7 Where to Go Next CHAPTER 5 4-7 Universal Port Dial Feature Card Overview 4-2 5-1 5-1 Online Insertion
Contents Getting Help APPENDIX A 6-10 Cabling Specifications A-1 T1 and E1 Cable and Port Pinouts A-1 2-Port and 4-Port T1 or E1 DFC A-1 8-Port T1 or E1 DFC A-3 Attaching the 8-Port Interface Cable to a Bracket (Optional) CT3 Cable and Port Pinouts Bantam Jack Port Pinouts A-5 A-10 A-10 INDEX Cisco AS5350 and Cisco AS5400 Universal Gateway Card Installation Guide 78-13311-01 v
Contents Cisco AS5350 and Cisco AS5400 Universal Gateway Card Installation Guide vi 78-13311-01
Preface This preface describes the objectives and organization of this document and explains how to find additional information on related products and services.
Preface Document Conventions Table 1 Document Organization (continued) Chapter Title Description Chapter 6 Troubleshooting Describes how to troubleshoot using LEDs, bantam jacks, and environmental monitoring. Appendix A Cabling Specifications Describes cabling and pinout information for the dial feature cards. Document Conventions This publication uses the following conventions to convey instructions and information.
Preface Document Conventions Tip Warning This symbol means the following information will help you solve a problem. The tips information might not be troubleshooting or even an action, but could be useful information, similar to a Timesaver. This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents.
Preface Document Conventions Advarsel Dette varselsymbolet betyr fare. Du befinner deg i en situasjon som kan føre til personskade. Før du utfører arbeid på utstyr, må du vare oppmerksom på de faremomentene som elektriske kretser innebærer, samt gjøre deg kjent med vanlig praksis når det gjelder å unngå ulykker.
Preface Obtaining Documentation Obtaining Documentation The following sections provide sources for obtaining documentation from Cisco Systems. World Wide Web You can access the most current Cisco documentation on the World Wide Web at the following sites: • http://www.cisco.com • http://www-china.cisco.com • http://www-europe.cisco.com Documentation CD-ROM Cisco documentation and additional literature are available in a CD-ROM package, which ships with your product.
Preface Obtaining Technical Assistance Obtaining Technical Assistance Cisco provides Cisco.com as a starting point for all technical assistance. Customers and partners can obtain documentation, troubleshooting tips, and sample configurations from online tools. For Cisco.com registered users, additional troubleshooting tools are available from the TAC website. Cisco.com Cisco.
Preface Related Documentation Contacting TAC by Telephone If you have a priority level 1(P1) or priority level 2 (P2) problem, contact TAC by telephone and immediately open a case. To obtain a directory of toll-free numbers for your country, go to the following website: http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml P1 and P2 level problems are defined as follows: • P1—Your production network is down, causing a critical impact to business operations if service is not restored quickly.
Preface New Hardware Features Cisco AS5350 and Cisco AS5400 Universal Gateway Card Installation Guide xiv 78-13311-01
C H A P T E R 1 Safety Warnings, Recommendations, and Tools Required This chapter describes the safety warnings, recommendations, and tools required to install dial feature cards in the chassis.
Chapter 1 Safety Warnings, Recommendations, and Tools Required Maintaining Safety with Electricity Maintaining Safety with Electricity Warning Before working on equipment that is connected to power lines, remove jewelry (including rings, necklaces, and watches). Metal objects will heat up when connected to power and ground and can cause serious burns or can weld the metal object to the terminals.
Chapter 1 Safety Warnings, Recommendations, and Tools Required Preventing Electrostatic Discharge Warning This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that a fuse or circuit breaker no larger than 120 VAC, 15A U.S. (240 VAC, 10A international) is used on the phase conductors (all current-carrying conductors).
Chapter 1 Safety Warnings, Recommendations, and Tools Required Where to Go Next • ESD-preventive mat • Blank filler panel Where to Go Next The remaining chapters of this guide include information on installing and troubleshooting DFCs and creating cables.
C H A P T E R 2 Dial Feature Card and Carrier Card Guidelines This chapter includes the following sections: • Overview, page 2-1 • Online Insertion and Removal (OIR) of DFCs, page 2-2 • Removing and Installing Populated Carrier Cards, page 2-2 • Getting Help, page 2-7 • Where to Go Next, page 2-7 Overview Cisco AS5350 Chassis The Cisco AS5350 universal gateway chassis has a motherboard, high-speed backplane, and two backplane slots.
Chapter 2 Dial Feature Card and Carrier Card Guidelines Online Insertion and Removal (OIR) of DFCs • Universal access (analog modem or digital calls) is supported when an interface is configured for ISDN PRI signaling. PRI signaling is available for both T1 and E1 trunks.
Chapter 2 Dial Feature Card and Carrier Card Guidelines Removing and Installing Populated Carrier Cards Warning Before performing any of the following procedures, ensure that power is removed from the DC circuit. To ensure that all power is OFF, locate the circuit breaker on the panel board that services the DC circuit, switch the circuit breaker to the OFF position, and tape the switch handle of the circuit breaker in the OFF position.
Chapter 2 Dial Feature Card and Carrier Card Guidelines Removing and Installing Populated Carrier Cards Figure 2-3 Loosen the Captive Screws on the Cisco AS5400 37159 Chassis Captive screw Step 4 DFC Carrier card DFC Captive screw Grasp the DFC handles and gently pull toward you to guide the carrier card out of the slot. Place one hand under the carrier card as you pull it out of the chassis. (See Figure 2-4 and Figure 2-5.) Note Use the DFC handles to remove the carrier card.
Chapter 2 Dial Feature Card and Carrier Card Guidelines Removing and Installing Populated Carrier Cards Step 6 If the backplane slot is to remain empty, install a blank cover over the open slot to ensure proper airflow inside the chassis. (See Figure 2-6.) Blank Filler Panel 36033 Figure 2-6 Installing a Populated Carrier Card To install a populated carrier card: Slide the carrier card into the slot until it touches the backplane connector. (See Figure 2-7 and Figure 2-8.
Chapter 2 Dial Feature Card and Carrier Card Guidelines Removing and Installing Populated Carrier Cards Step 3 Tighten the two captive screws to secure the carrier card to the chassis. (See Figure 2-9 and Figure 2-10.
Chapter 2 Dial Feature Card and Carrier Card Guidelines Getting Help Getting Help For information about technical support, onsite service, and exchange and repair services, refer to the “Obtaining Technical Assistance” section on page -xii in the “Preface.” Where to Go Next For instructions on installing and removing dial feature cards, refer to: • Chapter 3, “T1 and E1 Dial Feature Cards.” • Chapter 4, “T3 Dial Feature Card.” • Chapter 5, “Universal Port Dial Feature Card.
Chapter 2 Dial Feature Card and Carrier Card Guidelines Where to Go Next Cisco AS5350 and Cisco AS5400 Universal Gateway Card Installation Guide 2-8 78-13311-01
C H A P T E R 3 T1 and E1 Dial Feature Cards This chapter describes the installation and removal procedures for the T1 and E1 dial feature cards (DFC) and includes the following sections: • Overview, page 3-1 • Online Installation and Removal of the T1 or E1 DFC, page 3-3 • Configuring Input Impedance for the E1 DFC, page 3-11 • Getting Help, page 3-14 • Where to Go Next, page 3-14 Overview You can install a T1 or E1 dial feature card in any dial feature card slot of the universal gateway chassi
Chapter 3 T1 and E1 Dial Feature Cards Overview 4-Port T1 or E1 DFC Bantam ports T1 or E1 ports 56023 Figure 3-2 4 PRI 0 2 3 Rx Tx ACT OK/ MAINT 8-Port T1 or E1 DFC 29030 Figure 3-3 1 Table 3-1 T1 DFC Network Specifications Description Specification Line rate 1.544 Mbps Data rates (per port) number x 56 or number x 64 kbps, where number = 1 to 24 Standards AT&T Pub. 62411, 54016, and 43081, and ANSI T1.
Chapter 3 T1 and E1 Dial Feature Cards Online Installation and Removal of the T1 or E1 DFC Online Installation and Removal of the T1 or E1 DFC Overview To remove a DFC without dropping any calls or connections, you will need to take the DFC out of service by using the busyout command to disable the DFC. The busyout command is executed on a per DFC basis and will gracefully disable the card by waiting for the active services to terminate.
Chapter 3 T1 and E1 Dial Feature Cards Online Installation and Removal of the T1 or E1 DFC Slot Numbering on the Cisco AS5400 Chassis 34977 Figure 3-5 Slot 0 Slot 1 Slot 2 Slot 3 Slot 4 Slot 5 Slot 6 Slot 7 Step 2 Initialize the software busyout procedure by entering the busyout command: Router# busyout Step 3 slot-number Enter the show busyout command to check busyout status for that specific slot: Router# show busyout Step 4 slot-number You may use the clear port command to immediately disab
Chapter 3 T1 and E1 Dial Feature Cards Online Installation and Removal of the T1 or E1 DFC Step 8 Loosen the two captive screws that secure the DFC to the chassis until each screw is free of the chassis. (See Figure 3-6 and Figure 3-7.
Chapter 3 T1 and E1 Dial Feature Cards Online Installation and Removal of the T1 or E1 DFC Figure 3-8 Remove the DFC from the Cisco AS5350 Rx Tx ACT OK Remove the DFC from the Cisco AS5400 37164 Figure 3-9 1 36815 2 PRI 0 Step 10 After you remove the DFC from the chassis, set it aside on an ESD-preventive mat. Step 11 If the DFC slot is to remain empty, install a blank cover over the open DFC slot to ensure proper airflow inside the chassis. (See Figure 3-10.
Chapter 3 T1 and E1 Dial Feature Cards Online Installation and Removal of the T1 or E1 DFC 6/1 6/2 6/3 6/4 6/5 6/6 6/7 :s :s :s :s :s :s :s s s s s s s s s s s s s s p p p s p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p n n n n n n n p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p
Chapter 3 T1 and E1 Dial Feature Cards Online Installation and Removal of the T1 or E1 DFC Router# show busyout 6 Busyout status for trunk DFC slot = 6: DFC slot busyout is in progress (p - pending, s - static(cfg/exec), d - dynamic, n - none) 6/0 6/1 6/2 6/3 6/4 6/5 6/6 6/7 :s :s :s :s :s :s :s :s s s s s s s s s s s s s s s s p s p p s p p p p s p p p p p p p s p p p p p p p s p p p p p p p s p p p p p p p s p p p p p p p s p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p p
Chapter 3 T1 and E1 Dial Feature Cards Online Installation and Removal of the T1 or E1 DFC Installing the T1 or E1 DFC Warning Do not work on the system or connect or disconnect cables during periods of lightning activity. To see translations of the warnings that appear in this publication, refer to the Regulatory Compliance and Safety Information document that accompanied this device.
Chapter 3 T1 and E1 Dial Feature Cards Online Installation and Removal of the T1 or E1 DFC 37165 Figure 3-12 Install the T1 or E1 DFC in the Cisco AS5400 Step 3 Align the captive screws with their holes, and seat the card completely. Step 4 Tighten the screws to secure the DFC to the chassis. (See Figure 3-13 and Figure 3-14.
Chapter 3 T1 and E1 Dial Feature Cards Configuring Input Impedance for the E1 DFC Note For information about configuring the T1 or E1 ports, refer to the Cisco AS5350 and Cisco AS5400 Universal Gateway Software Configuration Guide. Configuring Input Impedance for the E1 DFC Use the line-termination command to set the input impedance for the E1 DFC. You can set the input impedance before or after running the setup script.
Chapter 3 T1 and E1 Dial Feature Cards Configuring Input Impedance for the E1 DFC service timestamps log datetime localtime show-timezone no service password-encryption service internal service udp-small-servers service tcp-small-servers ! hostname Router ! boot system flash flash:1:vdukki/c5400-i-mz enable secret 5 $1$qfO1$OYKRD2cvIJx7hfQbhrJS61 enable password lab ! bert profile default pattern 220-O.
Chapter 3 T1 and E1 Dial Feature Cards Configuring Input Impedance for the E1 DFC no ip mroute-cache ! interface Serial0 ip address 1.1.1.1 255.255.255.
Chapter 3 T1 and E1 Dial Feature Cards Getting Help ! interface FastEthernet0 mac-address 0000.0c00.0011 ip address 15.0.0.1 255.0.0.0 no ip directed-broadcast ip route-cache same-interface no ip route-cache no ip mroute-cache no keepalive duplex full hold-queue 75 in ! ip classless ip route 223.255.254.254 255.255.255.255 Ethernet0 ! access-list 101 permit ip any any access-list 101 deny igrp any any dialer-list 1 protocol ip list 101 arp 25.0.0.1 1234.1234.1241 ARPA arp 27.0.0.1 1234.1234.
4 C H A P T E R T3 Dial Feature Card This chapter describes the T3 dial feature card and includes the following sections: • Overview, page 4-1 • Online Installation and Removal (OIR) of the T3 DFC, page 4-2 • Getting Help, page 4-7 • Where to Go Next, page 4-7 Overview The T3 DFC provides physical line termination for a channelized T3 ingress trunk line. It uses an onboard multiplexer to multiplex 28 channelized T1 lines into a single channelized T3 line. (See Figure 4-1.
Chapter 4 T3 Dial Feature Card Online Installation and Removal (OIR) of the T3 DFC Online Installation and Removal (OIR) of the T3 DFC Overview To remove a DFC without dropping any calls or connections, you will need to take the DFC out of service by using the busyout command to disable the DFC. The busyout command is executed on a per DFC basis and will gracefully disable the card by waiting for the active services to terminate.
Chapter 4 T3 Dial Feature Card Online Installation and Removal (OIR) of the T3 DFC Slot Numbering on the Cisco AS5400 Chassis 34977 Figure 4-3 Slot 0 Slot 1 Slot 2 Slot 3 Slot 4 Slot 5 Slot 6 Slot 7 Step 2 Initialize the software busyout procedure by entering the busyout command: Router# busyout Step 3 slot-number Enter the show busyout command to check busyout status for that specific slot: Router# show busyout Step 4 slot-number You may use the clear port command to immediately disable active
Chapter 4 T3 Dial Feature Card Online Installation and Removal (OIR) of the T3 DFC Step 8 Loosen the two captive screws that secure the DFC to the chassis until each screw is free of the chassis. (See Figure 4-4 and Figure 4-5.
Chapter 4 T3 Dial Feature Card Online Installation and Removal (OIR) of the T3 DFC Remove the DFC from the Cisco AS5350 Figure 4-7 Remove the DFC from the Cisco AS5400 37168 58761 Figure 4-6 Step 10 After you remove the DFC from the chassis, set it aside on an ESD-preventive mat. Step 11 If a DFC slot on the carrier card is to remain empty, install a blank cover over the open DFC slot to ensure proper airflow inside the chassis. (See Figure 4-8.
Chapter 4 T3 Dial Feature Card Online Installation and Removal (OIR) of the T3 DFC To install the T3 DFC, follow these steps: Step 1 Attach an ESD-preventive wrist strap. Step 2 Slide the DFC into the slot until the connector pins make contact with the carrier card backplane connector. (See Figure 4-9 and Figure 4-10.
Chapter 4 T3 Dial Feature Card Getting Help 37170 Figure 4-12 Tighten the Captive Screws on the Cisco AS5400 Captive screw Step 5 Captive screw Check the card LEDs to verify that the card is working properly. For information about dial feature card LEDs, refer to Chapter 6, “Troubleshooting” Getting Help For information about technical support, onsite service, and exchange and repair services, refer to the “Obtaining Technical Assistance” section on page -xii in the “Preface.
Chapter 4 T3 Dial Feature Card Where to Go Next Cisco AS5350 and Cisco AS5400 Universal Gateway Card Installation Guide 4-8 78-13311-01
5 C H A P T E R Universal Port Dial Feature Card This chapter describes the universal port dial feature card (DFC) and includes the following sections: • Overview, page 5-1 • Online Insertion and Removal (OIR) of the Universal Port DFC, page 5-2 • SPE Firmware, page 5-9 • Getting Help, page 5-9 • Where to Go Next, page 5-9 Overview The universal port DFC provides multiple port sessions, with each session capable of originating or terminating a session over a DS-0 in PCM format.
Chapter 5 Universal Port Dial Feature Card Online Insertion and Removal (OIR) of the Universal Port DFC Online Insertion and Removal (OIR) of the Universal Port DFC Overview To remove a DFC without dropping any calls or connections, you will need to take the DFC out of service by using the busyout command to disable the DFC. The busyout command is executed on a per DFC basis and will gracefully disable the card by waiting for the active services to terminate.
Chapter 5 Universal Port Dial Feature Card Online Insertion and Removal (OIR) of the Universal Port DFC Slot Numbering on the Cisco AS5400 Chassis 34977 Figure 5-3 Slot 0 Slot 1 Slot 2 Slot 3 Slot 4 Slot 5 Slot 6 Slot 7 Step 2 Initialize the software busyout procedure by entering the busyout command: Router# busyout Step 3 slot-number Enter the show busyout command to check busyout status for that specific slot: Router# show busyout Step 4 You may use the clear port command to immediately disable
Chapter 5 Universal Port Dial Feature Card Online Insertion and Removal (OIR) of the Universal Port DFC Step 8 Loosen the two captive screws that secure the DFC to the chassis until each screw is free of the chassis. (See Figure 5-4 and Figure 5-5.
Chapter 5 Universal Port Dial Feature Card Online Insertion and Removal (OIR) of the Universal Port DFC Remove the DFC from the Cisco AS5400 37172 Figure 5-7 Caution Avoid touching any pins or circuit board components during removal and installation of a DFC. Step 10 After you remove the DFC, set it aside on an ESD-preventive mat. Step 11 If the DFC slot is to remain empty, install a blank cover over the open DFC slot to ensure proper airflow inside the chassis. (See Figure 5-8.
Chapter 5 Universal Port Dial Feature Card Online Insertion and Removal (OIR) of the Universal Port DFC Router# Router# clear port 3 This will clear ports 3/00 - 3/107[confirm] Router# *Jan 1 00:14:22.
Chapter 5 Universal Port Dial Feature Card Online Insertion and Removal (OIR) of the Universal Port DFC Router# show chassis slot 3 Slot 3: DFC type is NP108 DFC OIR events: Number of insertions = 1, Number of removals = 1 DFC State is DFC_S_OPERATIONAL Installing the Universal Port DFC Warning Do not work on the system or connect or disconnect cables during periods of lightning activity.
Chapter 5 Universal Port Dial Feature Card Online Insertion and Removal (OIR) of the Universal Port DFC Step 4 Seat the DFC in the carrier by pushing the card firmly until the captive screws are aligned with their holes. Step 5 Tighten the screws to secure the DFC to the chassis. (See Figure 5-11 and Figure 5-12.
Chapter 5 Universal Port Dial Feature Card SPE Firmware SPE Firmware SPE firmware is automatically downloaded to a universal port DFC from the Cisco IOS image when you boot the system for the first time, or when you insert a universal port DFC while the system is operating. When you insert DFCs while the system is operating, the Cisco IOS image recognizes the cards and downloads the required firmware to the cards.
Chapter 5 Universal Port Dial Feature Card Where to Go Next Cisco AS5350 and Cisco AS5400 Universal Gateway Card Installation Guide 5-10 78-13311-01
C H A P T E R 6 Troubleshooting This chapter describes how to troubleshoot the universal gateway by referring to the LEDs on DFCs, and using the bantam jacks.
Chapter 6 Troubleshooting LEDs 8-Port T1 or E1 DFC LEDs LNK T3 DFC LEDs 31631 Figure 6-3 Local alarm, Remote alarm, or ACTIVITY (ACT) Loopback LED for OK/MAINT each T1/E1 port 31630 Figure 6-2 Loop LOS LA EN/DIS RA MA LNK ACTIVITY (ACT) OK/MAINT Universal Port DFC LEDs 31362 Figure 6-4 ACTIVITY (ACT) OK/MAINT Cisco AS5350 and Cisco AS5400 Universal Gateway Card Installation Guide 6-2 78-13311-01
Chapter 6 Troubleshooting LEDs Table 6-1 LEDs DFC LED State Description T1 or E1 DFC ACTIVITY (ACT) Fast flicker (Green) Indicates DFC is up and running. Slow flicker (Green) Indicates DFC is not yet fully functional. Green The T1 or E1 DFC has passed initial power-up diagnostics tests and is operating normally. Yellow The T1 or E1 DFC is not functioning. See the console for messages.
Chapter 6 Troubleshooting LEDs Table 6-1 LEDs (continued) DFC LED State Description T3 DFC ACTIVITY (ACT) Fast flicker Indicates DFC is up and running. Slow flicker Indicates DFC is not yet fully functional. On (Green) The CT3 DFC passed initial power-up diagnostics tests and is operating normally. Yellow The CT3 DFC is not functioning. See the console for messages.
Chapter 6 Troubleshooting LEDs Table 6-1 LEDs (continued) DFC LED State Description Universal Port DFC ACTIVITY (ACT) Flickering There is call activity on the DFC. OK/MAINT On The DFC passed the initial power-up diagnostic tests and is operating normally. Off Indicates that all calls associated with the card are shut down and it is safe to remove the card with the system powered on. 1. To display information about an M13 alarm, use the show CT3 EXEC command.
Chapter 6 Troubleshooting Environment Monitoring Environment Monitoring Overview The Cisco AS5350 and Cisco AS5400 contain temperature sensors to detect abnormal temperature conditions during system operation. The three levels of sensor detection are as follows: 1. When the operating temperature of the system exceeds 45° C, the system reaches a warning state. A warning message appears on the console.
Chapter 6 Troubleshooting Environment Monitoring If the operating temperature cools down to 45° C, Cisco IOS software powers on the first DFC, repeating the process for each DFC at 10 minute intervals. 3. When the operating temperature of the system rises above 65° C, Cisco IOS software shuts down all DFCs immediately. Displaying Environment Status You can use the command line interface (CLI) to check environment monitoring status of your universal gateway.
Chapter 6 Troubleshooting Environment Monitoring Temperature: Temperature Reading: Temperature at inlet is measured as 62C/143F. Temperature at outlet is measured as 74C/165F. Temperature State: Temperature is in critical state. DFC Busyout/Power-down: A DFC is powered down. Slot:1, Type:NP108 DFC A DFC is busyout. Slot:2, Type:T1 8 PRI DFC A DFC is busyout. Slot:3, Type:NP108 DFC Fans: Fans temperature delta is measured as 6C. All fans are running well. Power Supply: Redundant Power System is present.
Chapter 6 Troubleshooting Using the Bantam Jacks for Test Port Functionality Using the Bantam Jacks for Test Port Functionality Test port functionality is supported by Cisco IOS Release 12.1(2)XD and later releases. Monitoring Mode for the T1, E1 and T3 DFCs The monitor mode is available on the T1, E1 and T3 dial feature cards.
Chapter 6 Troubleshooting Troubleshooting Network Interfaces The test trunk drop-insert privileged EXEC command is used to enable or disable drop-insert mode on a T3 controller. When the system initially boots up, the drop-insert mode is disabled on all T3 controllers.
A P P E N D I X A Cabling Specifications This appendix provides cabling and pinout information for dial feature cards (DFCs) on the Cisco AS5350 and Cisco AS5400 universal gateway: Note • T1 and E1 Cable and Port Pinouts, page A-1 • Attaching the 8-Port Interface Cable to a Bracket (Optional), page A-8 • CT3 Cable and Port Pinouts, page A-13 • Bantam Jack Port Pinouts, page A-13 This appendix specifies pinouts only for the pins used.
Appendix A Cabling Specifications T1 and E1 Cable and Port Pinouts Figure A-1 through Figure A-5 show the types of cables that can connect to the RJ-45 connector on the T1 or E1 feature card. Figure A-1 RJ-45-to-DB-15 Cable Assembly J2 35644 J1 Table A-2 lists the RJ-45-to-DB-15 cable pinouts.
Appendix A Cabling Specifications T1 and E1 Cable and Port Pinouts Table A-4 lists the RJ-45-to-BNC cable pinouts.
Appendix A Cabling Specifications T1 and E1 Cable and Port Pinouts Table A-6 RJ-45-to-RJ-45 TE Cable Pinouts (continued) RJ-45 Pin Signal Description Direction J1-2 RX Ring Twisted Pair #1 J1-3 RX Shield Twisted Pair #3 J1-4 TX Tip Twisted Pair #2 —> J2-4 J1-5 TX Ring Twisted Pair #2 —> J2-5 J1-6 TX Shield Twisted Pair #4 <— RJ-45 TE Pin J2-2 J2-3 J2-6 Table A-7 lists the RJ-45-to-RJ-45 NT cable pinouts.
Appendix A Cabling Specifications T1 and E1 Cable and Port Pinouts Table A-9 lists the RJ-45 to bare wire cable pinouts.
Appendix A Cabling Specifications T1 and E1 Cable and Port Pinouts Figure A-6 8-Port T1/E1 Interface Cable P0 18 36 1 19 P1 P2 P3 P4 P6 P7 31603 P5 Table A-11 lists the port pinouts for the 8-port DFC serial port.
Appendix A Cabling Specifications T1 and E1 Cable and Port Pinouts Table A-11 8 PRI T1/E1 DFC Interface Cable (continued) Male and Female RJ-45 (CAB-DFC-OCTAL-xMF) From Signal Note Direction Signal To J1-21 TX_TIP Twisted Pair #2 ------> TX_TIP J8-4 J1-22 TX_RING Port 6 ------> TX_RING J8-5 J1-23 TX_TIP Twisted Pair #2 ------> TX_TIP J7-4 J1-24 TX_RING Port 5 ------> TX_RING J7-5 J1-25 TX_TIP Twisted Pair #2 ------> TX_TIP J6-4 J1-26 TX_RING Port 4 ------> TX_RING
Appendix A Cabling Specifications Attaching the 8-Port Interface Cable to a Bracket (Optional) Attaching the 8-Port Interface Cable to a Bracket (Optional) To attach the 8CT1/CE1 cable to a bracket: Step 1 Place the molded RJ-45 end of the cable on the bracket with the RJ-45 ports facing you. Align the two holes on the molded RJ-45 end of the cable with the holes on the bracket. (See Figure A-7.
Appendix A Cabling Specifications Attaching the 8-Port Interface Cable to a Bracket (Optional) Step 2 You can align the molded RJ-45 ends of the cables in different ways by following either Step a or Step b. a. Routing Cables with Molded RJ-45 Ends of Cables Next to Each Other 35059 Figure A-8 Place the molded RJ-45 ends of the cables next to each other. This placement creates space between the last molded RJ-45 end of the cable and the edge of the bracket adjacent to it.
Appendix A Cabling Specifications Attaching the 8-Port Interface Cable to a Bracket (Optional) b. Align the molded RJ-45 ends of the cables with an opening between each adjacent molded RJ-45 end of the cable. This placement creates space between each adjacent molded RJ-45 end. Route the cables through this space. (See Figure A-9.
Appendix A Cabling Specifications Attaching the 8-Port Interface Cable to a Bracket (Optional) Step 3 Secure the molded RJ-45 ends of the cables to the bracket with the flathead screws provided to you. (See Figure A-10.) Note To secure a single molded RJ-45 end of the cable, use the short flathead screws. To secure two (stacked) molded RJ-45 ends of the cables, use the long flathead screws.
Appendix A Cabling Specifications Attaching the 8-Port Interface Cable to a Bracket (Optional) Step 5 Insert the 36-pin cable connector into the 36-pin port on the AS54-DFC-8CT1/CE1 card. Tighten the captive screws on the 36-pin cable connector to secure the cable to the AS54-DFC-8CT1/CE1 card. (See Figure A-11.
Appendix A Cabling Specifications CT3 Cable and Port Pinouts CT3 Cable and Port Pinouts Figure A-12 shows a diagram of the CT3 interface cable assembly. See Table A-12 for the CT3 cable pinouts. 12951 Figure A-12 CT3 Cable Assembly Table A-12 CT3 Cable Pinouts Pin Description Receiver Port (On the left) 1 Rx signal 2 Ground Transmitter Port 1 Tx signal 2 Ground Bantam Jack Port Pinouts Table A-13 lists the port pinouts for the bantam jacks.
Appendix A Cabling Specifications Bantam Jack Port Pinouts Cisco AS5350 and Cisco AS5400 Universal Gateway Card Installation Guide A-14 78-13311-01
I N D E X Connecting the 36-Pin Cable Connector to an 8-port T1 DFC A-9 Numerics 2-Port or 4-Port T1 or E1 DFC LEDs (figure) 6-1 J-45 to DB-15 Interface Cable A-2 2-Port T1 or E1 DFC (figure) 3-1 RJ-45 to Bare Wire Interface Cable 4-Port T1 or E1 DFC (figure) 3-2 RJ-45 to BNC Interface Cable for 75-Ohm, Unbalanced Connections A-2 8-Port T1/E1 Interface Cable (figure) 8-Port T1 or E1 DFC (figure) A-3 RJ-45 to RJ-45 Interface Cable 3-2 8-Port T1 or E1 DFC LEDs (figure) A-3 A AC circuit break
Index Removing the Carrier Card from the Cisco AS5400 E RJ-45 to Bare Wire Interface Cable E1 network specifications (table) environment monitoring A-2 RJ-45 to BNC Interface Cable for 75-Ohm, Unbalanced Connections A-2 6-6 environment status, checking ESD wrist-strap, safety 3-2 2-4 RJ-45 to RJ-45 Interface Cable 6-7 A-2 RJ-45 to Twinax Interface Cable for 120-Ohm, Balanced Connections A-2 1-3 Routing Cables with Molded RJ-45 Ends of Cables Flush with Bracket Edges A-7 F Routing Cables wit
Index installing the T1 or E1 DFC installing the T3 DFC 3-9 N 4-5 installing the universal port DFC network interfaces, troubleshooting 5-7 install the carrier card in the Cisco As5350 (figure) 2-5 new hardware features install the carrier card in the Cisco AS5400 (figure) 2-5 note symbol, meaning of Install the DFC in the Cisco AS5400 (figure) 6-10 xiii viii 5-7 Install the T1 or E1 DFC in the Cisco AS5350 (figure) 3-9 O Install the T1 or E1 DFC in the Cisco AS5400 (figure) 3-10 obtain
Index removing a carrier card 2-3 T removing the carrier card from the Cisco AS5350 (figure) 2-4 removing the carrier card from the Cisco AS5400 (figure) 2-4 removing the T1 or E1 DFC 3-3 removing the universal port DFC required tools and equipment T1 network specifications (table) T1 or E1 DFCs (table) 1-3 RJ-45 to Bare Wire Interface Cable (figure) A-2 RJ-45 to BNC Interface Cable for 75-Ohm, Unbalanced Connections (figure) A-2 T3 cable pinouts 6-3 A-1 T3 DFC, installation and removal routi
Index troubleshooting, mixing WAN DFCs TX MON, Bantam Jack 6-5 6-9 U universal port DFC (figure) 5-1 universal port DFC, overview 5-1 universal port DFC LEDs (figure) 6-2 V verifying input impedance on the E1 DFC 3-11 W Warnings AC circuit breaker (15A) 1-3 chassis warning - disconnecting telephone-network cables 2-3 customer equipment 3-9 DC power disconnection 2-3 ground connection first 1-2 installation instructions 1-2 lightning activity 2-3, 3-4, 3-9, 4-3, 4-5, 5-3, 5-7 power su
Index Cisco AS5350 and Cisco AS5400 Universal Gateway Card Installation Guide IN-6 78-13311-01
