Installation and Upgrade Guide for Cisco Unified MeetingPlace Audio Server Release 6.x Published May 31, 2007 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
CONTENTS Preface vii Purpose Audience vii vii Naming Conventions vii Documentation Conventions ix Cisco Unified MeetingPlace Documentation x New Feature and Enhancement Information x Obtaining Documentation, Obtaining Support, and Security Guidelines CHAPTER 1 x Preparing to Install the Cisco Unified MeetingPlace 8100 Series Hardware Safety Warnings 1-1 1-2 Hardware Requirements 1-3 Tools Required for the Installation 1-4 Environmental Requirements for the Cisco Unified MeetingPlace 8
Contents Mounting the Cisco Unified MeetingPlace 8112 into a 19- or 23-Inch EIA Equipment Rack Mounting the Breakout Box for T1 PRI and E1 Cisco Unified MeetingPlace Systems 2-7 2-6 Connecting the Cables to the Cisco Unified MeetingPlace 8100 Series 2-10 Connecting the Power Cable to the Cisco Unified MeetingPlace 8100 Series 2-11 Connecting the SCSI Cable to the Cisco Unified MeetingPlace 8112 2-11 Connecting the LAN Cable to the Cisco Unified MeetingPlace 8100 Series 2-11 Connecting T1 CAS Telephony Ca
Contents Testing Inbound Calls for T1 CAS, T1 PRI, and E1 Telephony by Using a Dialing Sequence Testing Outbound Calls for T1 CAS, T1 PRI, and E1 Telephony Testing Scheduling 5-4 5-5 Testing Conferencing in Recorded Meetings 5-6 Testing Conferencing in Nonrecorded Meetings with Ad Hoc Recording Testing Cisco Unified MeetingPlace Web Conferencing Testing Network Latency CHAPTER 6 5-6 5-6 5-7 Maintaining the Cisco Unified MeetingPlace Audio Server System 6-1 Replacing the Filter in the Power Sup
Contents Installation and Upgrade Guide for Cisco Unified MeetingPlace Audio Server 6.
Preface This preface contains the following sections: • Purpose, page vii • Audience, page vii • Documentation Conventions, page ix • Cisco Unified MeetingPlace Documentation, page x • New Feature and Enhancement Information, page x • Obtaining Documentation, Obtaining Support, and Security Guidelines, page x Purpose This guide describes how to install and maintain the Cisco Unified MeetingPlace 8100 series hardware for a Cisco Unified MeetingPlace Audio Server Release 6.0 system.
Preface Table 1 Product Naming Conventions Term Definition Used in This Document As Cisco Unified MeetingPlace 8100 series server Includes Cisco Unified MeetingPlace 8106 and Cisco Unified MeetingPlace 8100 series Cisco Unified MeetingPlace 8112 servers. Cisco Unified Hardware on which Cisco Unified MeetingPlace 8106 Server MeetingPlace Audio Server software runs.
Preface Documentation Conventions Table 3 Conventions for Cisco Unified MeetingPlace Documentation Convention Description boldfaced text Used for: • Commands that you must enter exactly as shown. • Key and button names. • Information that you enter. italicized text Used for arguments for which you supply values. [ ] Used for elements that are optional. (square brackets) text in Courier font Used for information that appears on the screen.
Preface Cisco Unified MeetingPlace Documentation For descriptions and locations of Cisco Unified MeetingPlace documentation on Cisco.com, see the Documentation Guide for Cisco Unified MeetingPlace. The document is shipped with Cisco Unified MeetingPlace and is available at http://www.cisco.com/en/US/products/sw/ps5664/ps5669/products_documentation_roadmaps_list.htm l.
CH A P T E R 1 Preparing to Install the Cisco Unified MeetingPlace 8100 Series Hardware This chapter describes the requirements and hardware specifications for a Cisco Unified MeetingPlace 8100 series server. To ensure that the Cisco Unified MeetingPlace configuration integrates within your environment, refer to the configuration worksheets in the Installation Planning Guide for Cisco Unified MeetingPlace Release 6.0 at http://www.cisco.com/en/US/products/sw/ps5664/ps5669/prod_installation_guides_list.
Chapter 1 Preparing to Install the Cisco Unified MeetingPlace 8100 Series Hardware Safety Warnings Safety Warnings Read the following safety warnings before you begin installing the Cisco Unified MeetingPlace Audio Server system. Translations of the warnings are available online in Regulatory Compliance and Safety Information for Cisco MeetingPlace 8100 Series at http://www.cisco.com/en/US/products/sw/ps5664/ps5669/prod_installation_guides_list.html.
Chapter 1 Preparing to Install the Cisco Unified MeetingPlace 8100 Series Hardware Hardware Requirements Warning Blank faceplates and cover panels serve three important functions: they prevent exposure to hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not operate the system unless all cards, faceplates, front covers, and rear covers are in place.
Chapter 1 Preparing to Install the Cisco Unified MeetingPlace 8100 Series Hardware Tools Required for the Installation Tools Required for the Installation Before installing the Cisco Unified MeetingPlace Audio Server, confirm that you have the following tools necessary for a successful installation: • Laptop computer. • Null modem female to female DB9 serial cable. Cisco Systems provides this cable. (For details, see the “Connecting Your Laptop to Cisco Unified MeetingPlace” section on page 3-1.
Chapter 1 Preparing to Install the Cisco Unified MeetingPlace 8100 Series Hardware Environmental Requirements for the Cisco Unified MeetingPlace 8112 Environmental Requirements for the Cisco Unified MeetingPlace 8112 The recommended operating temperature range for the Cisco Unified MeetingPlace 8112 is 50 to 104 degrees Fahrenheit with a noncondensing humidity of 5 to 80 percent. It is essential to keep the Cisco Unified MeetingPlace 8112 equipment cool.
Chapter 1 T1 Digital Trunk Requirements for Cisco Unified MeetingPlace Systems Table 1-1 Preparing to Install the Cisco Unified MeetingPlace 8100 Series Hardware Power Requirements by Country for the Cisco Unified MeetingPlace 8100 Series Country Power Socket U.S. 115 VAC NEMA 5-15R socket. Outlet installed within 8 feet of the Audio Server. 240 VAC BS-1363 socket. Outlet installed within 8 feet of the Audio Server. 100 VAC (50 Hz for East Japan; 60 Hz for West Japan) NEMA 5-15R socket.
Chapter 1 Preparing to Install the Cisco Unified MeetingPlace 8100 Series Hardware T1-Supported Protocols for Cisco Unified MeetingPlace Systems Table 1-2 T1 Digital Trunk Requirements by Country Country Requirements U.S. Public network to Channel Service Unit (CSU) connection—recEive and transMit (E&M) wink start (line side and trunk side). Ground start or loop start (line side only). Canada Hong Kong U.S. only—FCC and CSA-listed CSU required. Customer-supplied connectors—USOC (male) RJ-48 jacks.
Chapter 1 Preparing to Install the Cisco Unified MeetingPlace 8100 Series Hardware T1-Supported Protocols for Cisco Unified MeetingPlace Systems End-to-end positive disconnect supervision is essential. Without it, Cisco Unified MeetingPlace cannot reliably tell when a caller hangs up. Many PBX and central office systems can provide disconnect signaling; we recommend E&M wink start lines because they provide for a positive answer and disconnect supervision.
Chapter 1 Preparing to Install the Cisco Unified MeetingPlace 8100 Series Hardware Wiring Requirements for Customer-Supplied Connectors—U.S., Canada, and Hong Kong Wiring Requirements for Customer-Supplied Connectors—U.S., Canada, and Hong Kong Table 1-3 and Table 1-4 describe wiring requirements for customer-supplied RJ-48 connectors.
Chapter 1 E1 Digital Trunk Requirements for Cisco Unified MeetingPlace Systems Preparing to Install the Cisco Unified MeetingPlace 8100 Series Hardware E1 Digital Trunk Requirements for Cisco Unified MeetingPlace Systems Confirm that the E1 digital trunk specifications meet the requirements in Table 1-6. Table 1-6 E1 Digital Trunk Requirements Country Requirements European Union Connection Type—Euro ISDN and QSIG digital telephony (E1).
Chapter 1 Preparing to Install the Cisco Unified MeetingPlace 8100 Series Hardware Modem Requirements for Cisco Unified MeetingPlace Systems Figure 1-3 Cisco Unified MeetingPlace Digital Connection Requirements—E1 PBX PSTN E1 Euro ISDN QSIG E1 Euro ISDN Customer-supplied RJ-45 connectors Channel service unit (CSU) (optional) Network interface unit (NIU) T1 Smart Blade Cisco Unified MeetingPlace Audio Server system 153999 Special 23 ft cable shipped with unit Modem Requirements for Cisco Unified
Chapter 1 Preparing to Install the Cisco Unified MeetingPlace 8100 Series Hardware LAN Requirements for Cisco Unified MeetingPlace Systems Table 1-7 Modem Requirements by Country (continued) Country Requirements Japan European Union • CE modem supplied by Cisco Systems. • Serial cable. • 8.2-foot modem cable. • Customer-supplied standard analog phone jack (RJ-11). You must be able to call the extension from the outside. • Global modem supplied by Cisco Systems. • Serial cable.
Chapter 1 Preparing to Install the Cisco Unified MeetingPlace 8100 Series Hardware LAN Cable Requirements for Cisco Unified MeetingPlace Systems LAN Cable Requirements for Cisco Unified MeetingPlace Systems The Cisco Unified MeetingPlace Audio Server system attaches to an Ethernet LAN, which provides all the communication from the Audio Server system to your network. There are two possible scenarios for using an Ethernet LAN cable: • Connecting from an Audio Server CPU to your network.
Chapter 1 Preparing to Install the Cisco Unified MeetingPlace 8100 Series Hardware LAN Cable Requirements for Cisco Unified MeetingPlace Systems Installation and Upgrade Guide for Cisco Unified MeetingPlace Audio Server 6.
CH A P T E R 2 Installing the Cisco Unified MeetingPlace 8100 Series Hardware This chapter contains the following sections: • Contents of Shipped Boxes for the Cisco Unified MeetingPlace Audio Server System, page 2-1 • Mounting the Cisco Unified MeetingPlace 8100 Series, page 2-3 • Connecting the Cables to the Cisco Unified MeetingPlace 8100 Series, page 2-10 • About Telephony Configurations for E1 and T1 PRI Cisco Unified MeetingPlace Systems, page 2-15 • About Telephony Configurations for IP Ci
Chapter 2 Contents of Shipped Boxes for the Cisco Unified MeetingPlace Audio Server System Installing the Cisco Unified MeetingPlace 8100 Series Hardware • The number of E1 telephony cables that you receive depends on the number of Multi Access Blades that were purchased for the Cisco Unified MeetingPlace system. You receive 16 cables with each Multi Access Blade.
Chapter 2 Installing the Cisco Unified MeetingPlace 8100 Series Hardware Mounting the Cisco Unified MeetingPlace 8100 Series • Trunk card interface cable assemblies (50-pin Amphenol cables). The number of trunk card interface cable assemblies that you receive depends on how many and the type of Multi Access Blades in the Cisco Unified MeetingPlace system. Cisco Systems ships two cables with each MP-MA-16-PRI and one cable with each MP-MA-4-PRI.
Chapter 2 Installing the Cisco Unified MeetingPlace 8100 Series Hardware Mounting the Cisco Unified MeetingPlace 8100 Series Step 2 Attach the Cisco Unified MeetingPlace 8106 to the rack. The Cisco Unified MeetingPlace 8106 comes with screws to attach the mounting brackets to the rack. See Figure 2-1.
Chapter 2 Installing the Cisco Unified MeetingPlace 8100 Series Hardware Mounting the Cisco Unified MeetingPlace 8100 Series Figure 2-2 Mounting the Cisco Unified MeetingPlace 8112 in a Frame-Relay Rack Front-mounting brackets OUT OF SERVICE OUT OF SERVICE 1 OUT OF SERVICE OUT OF SERVICE 2 OUT OF SERVICE OUT OF SERVICE OUT OF SERVICE OUT OF SERVICE 3 OUT OF SERVICE OUT OF SERVICE 4 OUT OF SERVICE OUT OF SERVICE 5 OUT OF SERVICE OUT OF SERVICE 6 7 OUT OF SERVICE OUT OF SERVICE 8 OUT OF SE
Chapter 2 Installing the Cisco Unified MeetingPlace 8100 Series Hardware Mounting the Cisco Unified MeetingPlace 8100 Series Figure 2-3 Mounting the Cisco Unified MeetingPlace 8106 in an EIA Equipment Rack Mounting the Cisco Unified MeetingPlace 8112 into a 19- or 23-Inch EIA Equipment Rack In a 19- or 23-inch EIA equipment rack, you mount the Cisco Unified MeetingPlace 8112 on the front rails.
Chapter 2 Installing the Cisco Unified MeetingPlace 8100 Series Hardware Mounting the Cisco Unified MeetingPlace 8100 Series Figure 2-4 Mounting the Cisco Unified MeetingPlace 8112 into an EIA Equipment Rack Rack-mounting holes OUT OF SERVICE OUT OF SERVICE 1 OUT OF SERVICE OUT OF SERVICE 2 OUT OF SERVICE OUT OF SERVICE OUT OF SERVICE OUT OF SERVICE 3 OUT OF SERVICE OUT OF SERVICE 4 OUT OF SERVICE OUT OF SERVICE 5 OUT OF SERVICE OUT OF SERVICE 6 7 OUT OF SERVICE OUT OF SERVICE 8 OUT OF S
Chapter 2 Installing the Cisco Unified MeetingPlace 8100 Series Hardware Mounting the Cisco Unified MeetingPlace 8100 Series To Mount the Breakout Box for a T1 PRI or E1 Cisco Unified MeetingPlace System Step 1 Locate the breakout box that shipped with the Cisco Unified MeetingPlace Audio Server. Step 2 Locate the screws for mounting the breakout box that came with the Cisco Unified MeetingPlace Audio Server.
Chapter 2 Installing the Cisco Unified MeetingPlace 8100 Series Hardware Mounting the Cisco Unified MeetingPlace 8100 Series Figure 2-6 Mounting the Breakout Box for a Cisco Unified MeetingPlace 8112 Installation and Upgrade Guide for Cisco Unified MeetingPlace Audio Server 6.
Chapter 2 Installing the Cisco Unified MeetingPlace 8100 Series Hardware Connecting the Cables to the Cisco Unified MeetingPlace 8100 Series Figure 2-7 Mounting Two Breakout Boxes for a Cisco Unified MeetingPlace 8112 Connecting the Cables to the Cisco Unified MeetingPlace 8100 Series This section contains the following information: • Connecting the Power Cable to the Cisco Unified MeetingPlace 8100 Series, page 2-11 • Connecting the SCSI Cable to the Cisco Unified MeetingPlace 8112, page 2-11 • C
Chapter 2 Installing the Cisco Unified MeetingPlace 8100 Series Hardware Connecting the Cables to the Cisco Unified MeetingPlace 8100 Series Connecting the Power Cable to the Cisco Unified MeetingPlace 8100 Series Warning This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available.
Chapter 2 Installing the Cisco Unified MeetingPlace 8100 Series Hardware Connecting the Cables to the Cisco Unified MeetingPlace 8100 Series Step 3 Plug the other end of the LAN cable into Ethernet connection 1 on the CPU transition module that is located in the back of the Cisco Unified MeetingPlace Audio Server.
Chapter 2 Installing the Cisco Unified MeetingPlace 8100 Series Hardware Connecting the Cables to the Cisco Unified MeetingPlace 8100 Series To Connect the T1 CAS Telephony Cables for a Cisco Unified MeetingPlace 8106 Step 1 Locate the T1 CAS telephony cables that shipped with the Cisco Unified MeetingPlace system. Each T1 CAS telephony cable has an RJ-48 connector on each end. Step 2 Plug one end of the first T1 CAS telephony cable into the socket.
Chapter 2 Installing the Cisco Unified MeetingPlace 8100 Series Hardware Connecting the Cables to the Cisco Unified MeetingPlace 8100 Series Figure 2-9 Back of Cisco Unified MeetingPlace 8112 Audio Server with T1s Connected To Connect the T1 CAS Telephony Cables for a Cisco Unified MeetingPlace 8112 Step 1 Locate the T1 CAS telephony cables that shipped with the Cisco Unified MeetingPlace system. Each T1 CAS telephony cable has an RJ-48 connector on each end.
Chapter 2 Installing the Cisco Unified MeetingPlace 8100 Series Hardware About Telephony Configurations for E1 and T1 PRI Cisco Unified MeetingPlace Systems About Telephony Configurations for E1 and T1 PRI Cisco Unified MeetingPlace Systems Cisco Systems ships the necessary number of Multi Access Blades with all Cisco Unified MeetingPlace Audio Server systems with E1 and T1 PRI configurations.
Chapter 2 About Telephony Configurations for E1 and T1 PRI Cisco Unified MeetingPlace Systems Figure 2-10 Installing the Cisco Unified MeetingPlace 8100 Series Hardware 50-Pin Amphenol Cable Cisco Systems ships the necessary number of E1 or T1 PRI telephony cables with the Cisco Unified MeetingPlace Audio Server system. The number depends on the number of ports being activated.
Chapter 2 Installing the Cisco Unified MeetingPlace 8100 Series Hardware About Telephony Configurations for E1 and T1 PRI Cisco Unified MeetingPlace Systems Figure 2-11 shows the cable connections for a Cisco Unified MeetingPlace 8106 with 480 E1 ports. Figure 2-11 Front of Cisco Unified MeetingPlace 8106 with Cables Connected Installation and Upgrade Guide for Cisco Unified MeetingPlace Audio Server 6.
Chapter 2 About Telephony Configurations for E1 and T1 PRI Cisco Unified MeetingPlace Systems Installing the Cisco Unified MeetingPlace 8100 Series Hardware Figure 2-12 shows the cable connections for a Cisco Unified MeetingPlace 8112 with 480 E1 ports.
Chapter 2 Installing the Cisco Unified MeetingPlace 8100 Series Hardware About Telephony Configurations for E1 and T1 PRI Cisco Unified MeetingPlace Systems Connecting E1 or T1 PRI Telephony Cables with One Multi Access Blade MP-MA-16-PRI To Connect the E1 or T1 PRI Telephony Cables with One Multi Access Blade MP-MA-16-PRI Step 1 Step 2 Locate the following items shipped with the Cisco Unified MeetingPlace Audio Server: • E1 or T1 PRI telephony cables.
Chapter 2 About Telephony Configurations for E1 and T1 PRI Cisco Unified MeetingPlace Systems Figure 2-15 Installing the Cisco Unified MeetingPlace 8100 Series Hardware Multi Access Blade Transition Module (Cisco Unified MeetingPlace 8106) For the Cisco Unified MeetingPlace 8112, the connector on the top of the Multi Access Blade transition module is for spans 1 to 8 and the connector on the bottom of the Multi Access Blade transition module is for spans 9 to 16.
Chapter 2 Installing the Cisco Unified MeetingPlace 8100 Series Hardware About Telephony Configurations for E1 and T1 PRI Cisco Unified MeetingPlace Systems Step 7 Repeat Step 5 and Step 6 for the second trunk card cable assembly (50-pin Amphenol cable). For the Cisco Unified MeetingPlace 8106, place the second trunk card cable assembly into the connectors on the left of the breakout box and on the left of the Multi Access Blade.
Chapter 2 About Telephony Configurations for E1 and T1 PRI Cisco Unified MeetingPlace Systems Figure 2-18 Installing the Cisco Unified MeetingPlace 8100 Series Hardware Back of Cisco Unified MeetingPlace 8112 (E1 with 1 MP-MA-16-PRI) Figure 2-19 shows the connections on the back of a Cisco Unified MeetingPlace 8106. This configuration supports 368 T1 PRI ports with one Multi Access Blade card MP-MA-16-PRI.
Chapter 2 Installing the Cisco Unified MeetingPlace 8100 Series Hardware About Telephony Configurations for E1 and T1 PRI Cisco Unified MeetingPlace Systems Figure 2-20 Back of Cisco Unified MeetingPlace 8112 (T1 PRI with 1 MP-MA-16-PRI) Connecting E1 or T1 PRI Telephony Cables with One Multi Access Blade MP-MA-4-PRI To Connect E1 or T1 PRI Telephony Cables with One Multi Access Blade MP-MA-4-PRI Step 1 Locate the following items that shipped with the Cisco Unified MeetingPlace Audio Server: • E1 or T
Chapter 2 About Telephony Configurations for E1 and T1 PRI Cisco Unified MeetingPlace Systems Step 2 Installing the Cisco Unified MeetingPlace 8100 Series Hardware Attach the far end of the first E1 or T1 PRI telephony cable to the equipment that will connect with Cisco Unified MeetingPlace. In many cases, the other equipment has an RJ-48c socket in which to plug the E1 or T1 PRI telephony cable. Alternately, the other equipment will be connected to a punchdown block.
Chapter 2 Installing the Cisco Unified MeetingPlace 8100 Series Hardware About Telephony Configurations for E1 and T1 PRI Cisco Unified MeetingPlace Systems Step 4 Repeat Step 2 and Step 3 until all the E1 or T1 PRI telephony cables are connected to the breakout box. Place the second, third, and fourth E1 or T1 PRI telephony cables, which correspond to the first MP-MA-4-PRI, into the RJ-45 jacks labeled 2, 3, and 4.
Chapter 2 About Telephony Configurations for E1 and T1 PRI Cisco Unified MeetingPlace Systems Step 2 Installing the Cisco Unified MeetingPlace 8100 Series Hardware Attach the far end of the first E1 or T1 PRI telephony cable to the equipment that will connect with Cisco Unified MeetingPlace. In many cases, the other equipment has an RJ-48c socket in which to plug the E1 or T1 PRI telephony cable. Alternately, the other equipment will be connected to a punchdown block.
Chapter 2 Installing the Cisco Unified MeetingPlace 8100 Series Hardware About Telephony Configurations for IP Cisco Unified MeetingPlace Systems Step 2 Attach the far end of the first E1 or T1 PRI telephony cable to the equipment that will connect with Cisco Unified MeetingPlace. In many cases, the other equipment has an RJ-48c socket in which to plug theE1 or T1 PRI telephony cable. Alternately, the other equipment will be connected to a punchdown block.
Chapter 2 Installing the Cisco Unified MeetingPlace 8100 Series Hardware About Telephony Configurations for IP Cisco Unified MeetingPlace Systems Connecting IP Telephony Cables for Cisco Unified MeetingPlace Systems To Connect IP Telephony Cables for a Cisco Unified MeetingPlace System Step 1 Locate the IP LAN cables that shipped with the Cisco Unified MeetingPlace Audio Server. Step 2 Attach the far end of the first IP LAN cable to the RJ-45 socket of the switch or other network equipment.
Chapter 2 Installing the Cisco Unified MeetingPlace 8100 Series Hardware About Telephony Configurations for IP Cisco Unified MeetingPlace Systems Figure 2-22 Back of Cisco Unified MeetingPlace 8112 (IP with 1 MP-MA-16) Figure 2-23 shows the connections on the back of a Cisco Unified MeetingPlace 8106. This configuration supports 120 IP ports with one MP-MA-4.
Chapter 2 About Telephony Configurations for Mixed Cisco Unified MeetingPlace Systems Figure 2-24 Installing the Cisco Unified MeetingPlace 8100 Series Hardware Back of Cisco Unified MeetingPlace 8112 (IP with 1 MP-MA-4) About Telephony Configurations for Mixed Cisco Unified MeetingPlace Systems A mixed Cisco Unified MeetingPlace system is a Cisco Unified MeetingPlace Audio Server system with both an IP configuration and a T1 CAS, T1 PRI, or E1 configuration.
Chapter 2 Installing the Cisco Unified MeetingPlace 8100 Series Hardware About Telephony Configurations for Mixed Cisco Unified MeetingPlace Systems Cisco Systems ships all Cisco Unified MeetingPlace Audio Server systems with the necessary number of cards and cables for the type of mixed configuration: For All Mixed Configurations E1, T1 PRI, and IP configurations all use Multi Access Blades.
Chapter 2 About Telephony Configurations for Mixed Cisco Unified MeetingPlace Systems Installing the Cisco Unified MeetingPlace 8100 Series Hardware Connecting the Telephony Cables for an E1/IP or T1 PRI/IP Cisco Unified MeetingPlace System To Connect the Telephony Cables for an E1/IP or T1 PRI/IP Cisco Unified MeetingPlace System Step 1 Locate the following items that shipped with the Cisco Unified MeetingPlace Audio Server: • IP LAN cables. • E1 or T1 PRI telephony cables. • Breakout box.
Chapter 2 Installing the Cisco Unified MeetingPlace 8100 Series Hardware About Telephony Configurations for Mixed Cisco Unified MeetingPlace Systems Two MP-MA-4s are used for the IP configuration and are in slots 15 and 16, shown on the left. For the T1 CAS configuration, there is a T1 Smart Blade in slot 1 and three Smart Blades in slots 2, 3, and 4.
Chapter 2 About Telephony Configurations for Mixed Cisco Unified MeetingPlace Systems Figure 2-27 Installing the Cisco Unified MeetingPlace 8100 Series Hardware Back of Cisco Unified MeetingPlace 8112 (Mixed Configuration with 23 T1 PRI and 120 IP Ports) Figure 2-28 shows the connections on the back of a Cisco Unified MeetingPlace 8112 with a mixed Cisco Unified MeetingPlace system with 480 E1 ports and 480 IP ports. The MP-MA-16 that is used for the IP configuration is shown on the left in slot 16.
Chapter 2 Installing the Cisco Unified MeetingPlace 8100 Series Hardware About Telephony Configurations for Mixed Cisco Unified MeetingPlace Systems Figure 2-28 Back of Cisco Unified MeetingPlace 8112 (Mixed Configuration with 480 E1 and 480 IP Ports) Connecting the Telephony Cables for a T1 CAS/IP Cisco Unified MeetingPlace System To Connect the Telephony Cables for a T1 CAS/IP Cisco Unified MeetingPlace System Step 1 Step 2 Locate the following items that shipped with the Cisco Unified MeetingPlace
Chapter 2 Installing the Cisco Unified MeetingPlace 8100 Series Hardware Installing and Connecting the Modem Step 3 Plug the other end of the first T1 CAS telephony cable into the T1 Smart Blade transition module in the back of the Cisco Unified MeetingPlace Audio Server. For the Cisco Unified MeetingPlace 8106, place the first T1 CAS telephony cable in the left most connector slot. Place the second T1 CAS telephony cable in the next connector slot moving to the right, and so on.
Chapter 2 Installing the Cisco Unified MeetingPlace 8100 Series Hardware Installing and Connecting the Modem Step 7 Looking at the back of the Cisco Unified MeetingPlace Audio Server, connect the DB25 end (the larger connector) of the modem cable to the back of the modem. See Figure 2-29 to see which end is the DB25 end.
Chapter 2 Installing the Cisco Unified MeetingPlace 8100 Series Hardware Installing and Connecting the Modem Installation and Upgrade Guide for Cisco Unified MeetingPlace Audio Server 6.
CH A P T E R 3 Connecting and Setting Up Your Laptop Computer This chapter explains how to connect your laptop to the Cisco Unified MeetingPlace system and how to set up your laptop so that you can use HyperTerminal.
Chapter 3 Connecting and Setting Up Your Laptop Computer About Configuring Your Laptop Figure 3-1 Null Modem Cable Pinouts Step 2 Connect one end of the null modem cable to the COM 1 port on the CPU card in the front of the Cisco Unified MeetingPlace Audio Server. Step 3 Connect the other end of the null modem cable to the COM port on your laptop.
Chapter 3 Connecting and Setting Up Your Laptop Computer Setting Up HyperTerminal Setting Up HyperTerminal This section explains how to set up HyperTerminal to telnet to the Cisco Unified MeetingPlace system. There are several ways to telnet to the Cisco Unified MeetingPlace system. HyperTerminal is available on all operating systems. These instructions are for the Microsoft Windows 2000 operating system. If you are not using this version, the HyperTerminal instructions may vary.
Chapter 3 Connecting and Setting Up Your Laptop Computer Setting Up Dial-Up Networking Setting Up Dial-Up Networking This section explains how to set up dial-up networking on a Microsoft Windows 2000 operating system to connect to the Cisco Unified MeetingPlace Audio Server system by using a modem. To Set Up Dial-Up Networking Step 1 On the Windows 2000 system, right-click the My Network Places icon on the desktop. Step 2 Select Properties. Step 3 Double-click Make New Connection.
Chapter 3 Connecting and Setting Up Your Laptop Computer Testing the Modem Connection Step 2 Select Properties. The Network and Dial-up Connections window appears. Step 3 Double-click the connection that you just created. Step 4 Click Dial. Installation and Upgrade Guide for Cisco Unified MeetingPlace Audio Server 6.
Chapter 3 Connecting and Setting Up Your Laptop Computer Testing the Modem Connection Installation and Upgrade Guide for Cisco Unified MeetingPlace Audio Server 6.
CH A P T E R 4 Upgrading the Cisco Unified MeetingPlace Audio Server Software This chapter describes how to upgrade the Cisco Unified MeetingPlace Audio Server software from Release 5.3 or 5.4 to Release 6.0 and contains the following sections: • Upgrading the Cisco Unified MeetingPlace Audio Server Software to Release 6.0, page 4-1 • Testing the Upgrade, page 4-3 Upgrading the Cisco Unified MeetingPlace Audio Server Software to Release 6.
Chapter 4 Upgrading the Cisco Unified MeetingPlace Audio Server Software to Release 6.0 Note Upgrading the Cisco Unified MeetingPlace Audio Server Software The default username is admin, and the default password is cisco. Step 5 Shut down the Cisco Unified MeetingPlace Audio Server software by entering down. Step 6 Note the current time. Step 7 Save the session capture to your desktop with the filename upgrade.txt.
Chapter 4 Upgrading the Cisco Unified MeetingPlace Audio Server Software Testing the Upgrade When Phase 2 is complete, the modem connection terminates. After approximately 5 minutes, the Cisco Unified MeetingPlace Audio Server system comes back up and you can re-establish a modem connection. To view the upgrade status, enter update status. The Cisco Unified MeetingPlace Audio Server system displays a message with the date and time of the last update.
Chapter 4 Upgrading the Cisco Unified MeetingPlace Audio Server Software Testing the Upgrade Installation and Upgrade Guide for Cisco Unified MeetingPlace Audio Server 6.
CH A P T E R 5 Testing the Cisco Unified MeetingPlace Audio Server System Installation and Upgrade This chapter explains how to power up the Cisco Unified MeetingPlace Audio Server and how to test the installation and upgrade.
Chapter 5 Testing the Cisco Unified MeetingPlace Audio Server System Installation and Upgrade About Testing the Cisco Unified MeetingPlace Audio Server System Installation or Upgrade Step 3 Step 4 If the Cisco Unified MeetingPlace Audio Server is not up, confirm that all components are secure: a. Confirm that all the cards are securely seated. (For the Cisco Unified MeetingPlace 8112, check if any of the blue LED lights below the cards are on.
Chapter 5 Testing the Cisco Unified MeetingPlace Audio Server System Installation and Upgrade Testing Inbound Calls for T1 CAS, T1 PRI, and E1 Telephony by Using Circular Hunting Unified MeetingPlace Audio Server at http://www.cisco.com/en/US/products/sw/ps5664/ps5669/products_installation_and_configuration_gu ides_list.html.
Chapter 5 Testing the Cisco Unified MeetingPlace Audio Server System Installation and Upgrade Testing Inbound Calls for T1 CAS, T1 PRI, and E1 Telephony by Using a Dialing Sequence Step 5 When you hear the prompt “Welcome to MeetingPlace,” press 2. The Cisco Unified MeetingPlace system replies with “Enter your profile number.” This verifies a full two-way connection between the PBX and central office. Step 6 Dial the Cisco Unified MeetingPlace system access number until each port is tested.
Chapter 5 Testing the Cisco Unified MeetingPlace Audio Server System Installation and Upgrade Testing Scheduling DebugMenu: 1) Quick Status of all Ports 2) Verbose Status of Port Range 3) Display complete Port Information Enter the Command (0 -- 100): 4 You entered 4. Enter destination for your call: Note 4) Make Test Call 5) Show All Confs 0) Quit The preceding code examples are for a Cisco Unified MeetingPlace 8112. For a Cisco Unified MeetingPlace 8106, there are 576 sessions and 576 conferences.
Chapter 5 Testing the Cisco Unified MeetingPlace Audio Server System Installation and Upgrade Testing Conferencing in Recorded Meetings To Test Scheduling Step 1 Confirm that you can schedule a new meeting. Step 2 Confirm that you can attend the new meeting. Step 3 If the Cisco Unified MeetingPlace notification option is enabled, confirm that you can receive notifications when meetings are scheduled.
Chapter 5 Testing the Cisco Unified MeetingPlace Audio Server System Installation and Upgrade Testing Network Latency Testing Network Latency To Test Network Latency Step 1 Access the CLI and enter ping -s 1000 IP_address_of_another_machine_on_the_network. The “-s 1000”argument simulates normal network activity by sending 1,000 bytes of dummy data to the other IP address. Step 2 After you receive several reply messages, enter Ctrl-C.
Chapter 5 Testing the Cisco Unified MeetingPlace Audio Server System Installation and Upgrade Testing Network Latency Installation and Upgrade Guide for Cisco Unified MeetingPlace Audio Server 6.
CH A P T E R 6 Maintaining the Cisco Unified MeetingPlace Audio Server System This chapter describes how to maintain—not repair—the Cisco Unified MeetingPlace Audio Server system and contains the following sections: • Replacing the Filter in the Power Supply Unit Fan (Cisco Unified MeetingPlace 8112 Only), page 6-1 • Enabling Server Disk Capacity Monitoring, page 6-3 (For information about repairing the Cisco Unified MeetingPlace Audio Server system, contact Cisco TAC.
Chapter 6 Maintaining the Cisco Unified MeetingPlace Audio Server System Replacing the Filter in the Power Supply Unit Fan (Cisco Unified MeetingPlace 8112 Only) Note CLI commands are case sensitive. For CLI command information, refer to the “Command-Line Interface Reference” appendix of the Configuration Guide for Cisco Unified MeetingPlace Audio Server at http://www.cisco.com/en/US/products/sw/ps5664/ps5669/products_installation_and_configura tion_guides_list.html.
Chapter 6 Maintaining the Cisco Unified MeetingPlace Audio Server System Enabling Server Disk Capacity Monitoring PS2: PS3: SCSI Adapter: DISK 1: DISK 2: Solid State Disk: Ethernet: Modem: Smart Blades: Slot 16: Slot 15: OK, fan is OK OK, fan is OK NCR 810 36000MB (SEAGATE ST336704LW REV=0004) 36000MB (SEAGATE ST336704LW REV=0004) IMPERIAL "MG-35/400 ULTRA" S/N=0128 REV=B403 Battery: usage = 307 days, charge is OK Intel 8225x PCI 10/100 (0001af03c05e) Absent or unrecognized NMS CG6000C S/N=20363257 REV=5
Chapter 6 Maintaining the Cisco Unified MeetingPlace Audio Server System Enabling Server Disk Capacity Monitoring 3) 4) 5) 6) 0 0 0 0 /tmp /lat/fs.1 /lat/fs.2 /lat/fs.3 Select an item to modify, s to save and exit, or q to quit without saving: 2 enter new value for /lat/db: 95 1) 2) 3) 4) 5) 6) CAP% FILESYSTEM ==== ========== 0 / 95 /lat/db 0 /tmp 0 /lat/fs.1 0 /lat/fs.2 0 /lat/fs.
CH A P T E R 7 Troubleshooting the Cisco Unified MeetingPlace Audio Server System Installation The chapter contains the following sections: • Troubleshooting the Connection to the Audio Server System, page 7-1 • Troubleshooting Telephony Configuration, page 7-2 Troubleshooting the Connection to the Audio Server System If you cannot connect to the Cisco Unified MeetingPlace Audio Server system by using MeetingTime, try any or all of the following tasks: Note • Enter ping to ping a known good IP addr
Chapter 7 Troubleshooting the Cisco Unified MeetingPlace Audio Server System Installation Troubleshooting Telephony Configuration Troubleshooting Telephony Configuration To Troubleshoot Telephony Configuration Step 1 Check that the information you entered into MeetingTime from the worksheets in the Installation Planning Guide for Cisco Unified MeetingPlace is correct. Step 2 Check all the physical connections to the Cisco Unified MeetingPlace Audio Server system.
A P P E N D I X A Cisco Unified MeetingPlace Audio Server Software Upgrade Reference This appendix contains sample sessions of upgrading the Cisco Unified MeetingPlace Audio Server software. (See the “Upgrading the Cisco Unified MeetingPlace Audio Server Software” chapter for upgrade procedures.
Appendix A Viewing the Remote Upgrade for a Sample Session Without a Disk Backup Cisco Unified MeetingPlace Audio Server Software Upgrade Reference - Archive created: Fri Aug 1813:51:39 PDT 2006 --------------------------------------------------------------Press to continue or to abort. Mon Aug 21 14:20:41 PDT 2006 Starting ./UPDATE.
Appendix A Cisco Unified MeetingPlace Audio Server Software Upgrade Reference Viewing the Upgrade Status for a Remote Upgrade Session Viewing the Upgrade Status for a Remote Upgrade Session Release 5.4, Aug 21, 2006 user name: tech Password: Last login: Mon Aug 21 19:31:14 from Unknown-HostName ************************************************************************* * MeetingPlace(tm) * * by Cisco Systems * * * * Copyright (c) 1993-2006 Cisco Systems * * All rights reserved.
Appendix A Viewing the Real-Time Upgrade Status for a Remote Upgrade Session Cisco Unified MeetingPlace Audio Server Software Upgrade Reference ----------- db preallocation complete Mon Aug ----------- Preallocating deletedrec Mon Aug 21 19:55:19 PDT 2006 21 19:55:19 PDT 2006 Reserving 1000000 deletedrec records (code 10000) ... the deletedrec file already has 1000000 record(s) Pre-allocating each key file... Adding 2 16384 byte pages to key file deletedrec.Sequence...
Appendix A Cisco Unified MeetingPlace Audio Server Software Upgrade Reference Viewing the Real-Time Upgrade Status for a Remote Upgrade Session Adding 2 16384 byte pages to key file user.vuname... Adding 2 16384 byte pages to key file user.glfn... Adding 2 16384 byte pages to key file user.UpdateTime... ----------- gen preallocation complete Mon Aug 21 19:55:21 PDT 2006 Database Initialization Utility Centura RDM 5.0.0 [24-Apr-2000] http://www.centurasoft.
Appendix A Viewing the Real-Time Upgrade Status for a Remote Upgrade Session Adding Adding Adding Adding Cisco Unified MeetingPlace Audio Server Software Upgrade Reference 3 16384 byte pages to key file crres.resourceid... 3 16384 byte pages to key file portres.resourceid... 343 16384 byte pages to key file vsres.resourceid... 343 16384 byte pages to key file vsres.UpdateTime... ----------- res preallocation complete Mon Aug 21 19:55:26 PDT 2006 Database Initialization Utility Centura RDM 5.0.
Appendix A Cisco Unified MeetingPlace Audio Server Software Upgrade Reference Viewing the Real-Time Upgrade Status for a Remote Upgrade Session Reserving 1000 trunk records (code 10005) ... the trunk file already has 10800 record(s) Reserving 100 trunkgroup records (code 10006) ... the trunkgroup file already has 1 16384 byte pages that can hold 110 record(s) Reserving 100 e1card records (code 10007) ...
Appendix A Viewing the Real-Time Upgrade Status for a Remote Upgrade Session Cisco Unified MeetingPlace Audio Server Software Upgrade Reference 6000 8000 10000 12000 14000 16000 18000 20000 22000 24000 26000 28000 30000 32000 34000 36000 38000 40000 42000 44000 46000 48000 50000 52000 54000 56000 58000 60000 62000 64000 66000 68000 70000 72000 74000 76000 78000 80000 82000 84000 86000 88000 90000 92000 94000 96000 98000 100000 102000 104000 106000 108000 110000 112000 114000 116000 118000 120000 122000 12
Appendix A Cisco Unified MeetingPlace Audio Server Software Upgrade Reference Viewing the Real-Time Upgrade Status for a Remote Upgrade Session 134000 136000 138000 140000 142000 144000 146000 148000 150000 152000 154000 156000 158000 160000 162000 164000 166000 168000 170000 172000 174000 176000 178000 180000 182000 184000 186000 188000 190000 192000 194000 196000 198000 200000 202000 204000 206000 208000 210000 212000 214000 216000 218000 220000 222000 224000 226000 228000 230000 232000 234000 236000 23
Appendix A Viewing the Real-Time Upgrade Status for a Remote Upgrade Session Cisco Unified MeetingPlace Audio Server Software Upgrade Reference 262000 264000 266000 268000 270000 272000 274000 276000 278000 280000 282000 284000 286000 288000 290000 292000 294000 296000 298000 300000 302000 304000 306000 308000 310000 312000 314000 316000 318000 320000 322000 324000 326000 328000 330000 332000 334000 336000 338000 340000 342000 344000 346000 348000 350000 352000 354000 356000 358000 360000 362000 364000 36
Appendix A Cisco Unified MeetingPlace Audio Server Software Upgrade Reference Viewing the Real-Time Upgrade Status for a Remote Upgrade Session 390000 392000 394000 396000 398000 400000 402000 404000 406000 408000 410000 412000 414000 416000 418000 420000 422000 424000 426000 428000 430000 432000 434000 436000 438000 440000 442000 444000 446000 448000 450000 452000 454000 456000 458000 460000 462000 464000 466000 468000 470000 472000 474000 476000 478000 480000 482000 484000 486000 488000 490000 492000 49
Appendix A Viewing the Real-Time Upgrade Status for a Remote Upgrade Session Cisco Unified MeetingPlace Audio Server Software Upgrade Reference 518000 520000 522000 524000 526000 528000 530000 532000 534000 536000 538000 540000 542000 544000 546000 548000 550000 552000 554000 556000 558000 560000 562000 564000 566000 568000 570000 572000 574000 576000 578000 580000 582000 584000 586000 588000 590000 592000 594000 596000 598000 600000 602000 604000 606000 608000 610000 612000 614000 616000 618000 620000 62
Appendix A Cisco Unified MeetingPlace Audio Server Software Upgrade Reference Viewing the Real-Time Upgrade Status for a Remote Upgrade Session 646000 648000 650000 652000 654000 656000 658000 660000 662000 664000 666000 668000 670000 672000 674000 676000 678000 680000 682000 684000 686000 688000 690000 692000 694000 696000 698000 700000 702000 704000 706000 708000 710000 712000 714000 716000 718000 720000 722000 724000 726000 728000 730000 732000 734000 736000 738000 740000 742000 744000 746000 748000 75
Appendix A Viewing the Real-Time Upgrade Status for a Remote Upgrade Session Cisco Unified MeetingPlace Audio Server Software Upgrade Reference 774000 776000 778000 780000 782000 784000 786000 788000 790000 792000 794000 796000 798000 800000 802000 804000 806000 808000 810000 812000 814000 816000 818000 820000 822000 824000 826000 828000 830000 832000 834000 836000 838000 840000 842000 844000 846000 848000 850000 852000 854000 856000 858000 860000 862000 864000 866000 868000 870000 872000 874000 876000 87
Appendix A Cisco Unified MeetingPlace Audio Server Software Upgrade Reference Viewing the Real-Time Upgrade Status for a Remote Upgrade Session 902000 904000 906000 908000 910000 912000 914000 916000 918000 920000 922000 924000 926000 928000 930000 932000 934000 936000 938000 940000 942000 944000 946000 948000 950000 952000 954000 956000 958000 960000 962000 964000 966000 968000 970000 972000 974000 976000 978000 980000 982000 984000 986000 988000 990000 992000 994000 996000 998000 1000000 1000001 records
Appendix A Viewing the Onsite Upgrade for a Sample Session Without a Disk Backup Cisco Unified MeetingPlace Audio Server Software Upgrade Reference Prompt Upgrade>> EOF (0) reached in /lat/fs.1/prompt_db_vfs_map_dir0 file (promptNum 1551): 0 ...
Appendix A Cisco Unified MeetingPlace Audio Server Software Upgrade Reference Viewing the Onsite Upgrade for a Sample Session Without a Disk Backup Mon Aug 21 18:50:22 PDT 2006 Starting ./UPDATE.
Appendix A Viewing the Onsite Upgrade for a Sample Session Without a Disk Backup Cisco Unified MeetingPlace Audio Server Software Upgrade Reference LynxOS (x86) created Mon Aug 18 15:05:41 PDT 2006 MeetingPlace by Cisco Systems Mon Aug 21 19:01:07 PDT 2006 Startup flags = a (all sizes and block numbers in decimal) (block size is 16384) (file system is byte-swapped) (file system creation time is Mon Aug 21 18:50:30 2006) (file system contains 31999 blocks and 7936 inodes) checking used files checking for o
Appendix A Cisco Unified MeetingPlace Audio Server Software Upgrade Reference Viewing the Onsite Upgrade for a Sample Session Without a Disk Backup Current slot 0 (0 seconds) Processing file /lat/db/hwconfig containing 0 records Current slot 0 (0 seconds) Processing file /lat/db/hwstats containing 0 records Current slot 0 (0 seconds) Processing file /lat/db/option containing 22 records Current slot 22 (0 seconds) Processing file /lat/db/outdialtrans containing 16 records Current slot 16 (0 seconds) Proces
Appendix A Viewing the Onsite Upgrade for a Sample Session Without a Disk Backup Cisco Unified MeetingPlace Audio Server Software Upgrade Reference Current slot 0 (0 seconds) Processing file /lat/db/didcnfgconfig containing 16 records Current slot 16 (0 seconds) Processing file /lat/db/schedparamsconfig containing 1 records Current slot 1 (0 seconds) dbrev completed, successful restructure Database Restructure Utility Centura RDM 5.0.0 [24-Apr-2000] http://www.centurasoft.
Appendix A Cisco Unified MeetingPlace Audio Server Software Upgrade Reference Viewing the Onsite Upgrade for a Sample Session Without a Disk Backup Copying 5.4.0/outdialtrans.recnum: 32768 32768 Copying 5.4.0/option.name: 2048 2048 Copying 5.4.0/timezone.id: 32768 32768 Copying 5.4.0/timezone.timezonekey: 32768 32768 Copying 5.4.0/unit.unitnum: 32768 32768 Copying 5.4.0/site.sitenum: 32768 32768 Copying 5.4.0/scsi.unitid: 32768 32768 Copying 5.4.0/mtgcategory.uniqueid: 32768 32768 Copying 5.4.
Appendix A Viewing the Onsite Upgrade for a Sample Session Without a Disk Backup Cisco Unified MeetingPlace Audio Server Software Upgrade Reference Processing file /lat/db/didres containing 0 records Current slot 0 (0 seconds) Processing file /lat/db/didconfigres containing 0 records Current slot 0 (0 seconds) Processing file /lat/db/schedparamsres containing 0 records Current slot 0 (0 seconds) Processing file /lat/db/crresfstaccess containing 13 records Current slot 13 (0 seconds) Processing file /lat/d
Appendix A Cisco Unified MeetingPlace Audio Server Software Upgrade Reference Viewing the Onsite Upgrade for a Sample Session Without a Disk Backup 32768 32768 Copying 5.4.0/vsres.UpdateTime: 32768 32768 cmdbrev: starting /lat/bin/initdb -y 5.4.0/res Database Initialization Utility Centura RDM 5.0.0 [24-Apr-2000] http://www.centurasoft.com/rdm Copyright (c) 1992-2000 Centura Software Corporation. All Rights Reserved. 5.4.
Appendix A Viewing the Onsite Upgrade for a Sample Session Without a Disk Backup Cisco Unified MeetingPlace Audio Server Software Upgrade Reference Processing file /lat/db/e1span containing 36 records Current slot 36 (0 seconds) Processing file /lat/db/accard containing 27 records Current slot 27 (0 seconds) Processing file /lat/db/acspan containing 432 records Current slot 432 (0 seconds) Processing file /lat/db/iprescard containing 108 records Current slot 108 (0 seconds) Processing file /lat/db/blade c
Appendix A Cisco Unified MeetingPlace Audio Server Software Upgrade Reference Viewing the Onsite Upgrade for a Sample Session Without a Disk Backup 32768 32768 Copying 5.4.0/portrescard.unitid: 32768 32768 Copying 5.4.0/t1card.unitid: 32768 32768 Copying 5.4.0/t1span.unitid: 32768 32768 Copying 5.4.0/trunk.unitid: 327680 327680 Copying 5.4.0/trunkgroup.id: 32768 32768 Copying 5.4.0/e1card.unitid: 32768 32768 Copying 5.4.0/e1span.unitid: 32768 32768 Copying 5.4.0/accard.unitid: 32768 32768 Copying 5.4.
Appendix A Viewing the Onsite Upgrade for a Sample Session Without a Disk Backup Cisco Unified MeetingPlace Audio Server Software Upgrade Reference Fixing group records++++++++++++++++++++++++++++++++! update: upgradetcnfg done cmdbrev: 5.4/update done cmdbrev: starting dbprealloc -b /lat/db ----------- Preallocating conf_att Mon Aug 21 19:01:58 PDT 2006 Reserving 200000 confatt records (code 10000) ...
Appendix A Cisco Unified MeetingPlace Audio Server Software Upgrade Reference Viewing the Onsite Upgrade for a Sample Session Without a Disk Backup Reserving 1 companyinfo records (code 10001) ... the companyinfo file already has 1 record(s) Reserving 1 filestats records (code 10002) ... Adding 1 16384 byte page(s) to get 1 record(s) ... Reserving 1 hwconfig records (code 10003) ... Adding 1 16384 byte page(s) to get 1 record(s) ... Reserving 1 hwstats records (code 10004) ...
Appendix A Viewing the Onsite Upgrade for a Sample Session Without a Disk Backup Adding Adding Adding Adding Adding Adding Adding Adding Adding Adding Adding Cisco Unified MeetingPlace Audio Server Software Upgrade Reference 3 16384 byte pages to key file timezone.timezonekey... 3 16384 byte pages to key file unit.unitnum... 3 16384 byte pages to key file site.sitenum... 3 16384 byte pages to key file scsi.unitid... 17 16384 byte pages to key file mtgcategory.uniqueid...
Appendix A Cisco Unified MeetingPlace Audio Server Software Upgrade Reference Viewing the Onsite Upgrade for a Sample Session Without a Disk Backup Record 10005 (FMOptionMenu): has no preallocation count Record 10006 (FMHangUp): has no preallocation count Record 10007 (FMFindMtg): has no preallocation count Record 10008 (FMReviewMtgMat): has no preallocation count Record 10009 (FMGetProfile): has no preallocation count Pre-allocating each key file...
Appendix A Viewing the Onsite Upgrade for a Sample Session Without a Disk Backup Cisco Unified MeetingPlace Audio Server Software Upgrade Reference Reserving 1 pomailbox records (code 10000) ... the pomailbox file already has 32 record(s) Reserving 20000 pomsgdata records (code 10001) ... Pre-allocating each key file... Adding 2 16384 byte pages to key file pomsgdata.compundkey...
Appendix A Cisco Unified MeetingPlace Audio Server Software Upgrade Reference Viewing the Onsite Upgrade for a Sample Session Without a Disk Backup Reserving 1 swstatus records (code 10003) ... the swstatus file already has 1 record(s) Reserving 1500 exlogformat records (code 10004) ... the exlogformat file already has 3374 record(s) Reserving 20 apps records (code 10005) ... the apps file already has 21 record(s) Reserving 10000 outdial records (code 10006) ...
Appendix A Viewing the Onsite Upgrade for a Sample Session Without a Disk Backup Pre-allocating each key Adding 3 16384 byte Adding 3 16384 byte Adding 3 16384 byte Adding 3 16384 byte Adding 3 16384 byte Adding 3 16384 byte Adding 3 16384 byte Adding 3 16384 byte file... pages to pages to pages to pages to pages to pages to pages to pages to key key key key key key key key Cisco Unified MeetingPlace Audio Server Software Upgrade Reference file file file file file file file file analogcard.unitid...
Appendix A Cisco Unified MeetingPlace Audio Server Software Upgrade Reference Viewing the Onsite Upgrade for a Sample Session Without a Disk Backup 56000 58000 60000 62000 64000 66000 68000 70000 72000 74000 76000 78000 80000 82000 84000 86000 88000 90000 92000 94000 96000 98000 100000 102000 104000 106000 108000 110000 112000 114000 116000 118000 120000 122000 124000 126000 128000 130000 132000 134000 136000 138000 140000 142000 144000 146000 148000 150000 152000 154000 156000 158000 160000 162000 164000
Appendix A Viewing the Onsite Upgrade for a Sample Session Without a Disk Backup Cisco Unified MeetingPlace Audio Server Software Upgrade Reference 184000 186000 188000 190000 192000 194000 196000 198000 200000 202000 204000 206000 208000 210000 212000 214000 216000 218000 220000 222000 224000 226000 228000 230000 232000 234000 236000 238000 240000 242000 244000 246000 248000 250000 252000 254000 256000 258000 260000 262000 264000 266000 268000 270000 272000 274000 276000 278000 280000 282000 284000 28600
Appendix A Cisco Unified MeetingPlace Audio Server Software Upgrade Reference Viewing the Onsite Upgrade for a Sample Session Without a Disk Backup 312000 314000 316000 318000 320000 322000 324000 326000 328000 330000 332000 334000 336000 338000 340000 342000 344000 346000 348000 350000 352000 354000 356000 358000 360000 362000 364000 366000 368000 370000 372000 374000 376000 378000 380000 382000 384000 386000 388000 390000 392000 394000 396000 398000 400000 402000 404000 406000 408000 410000 412000 41400
Appendix A Viewing the Onsite Upgrade for a Sample Session Without a Disk Backup Cisco Unified MeetingPlace Audio Server Software Upgrade Reference 440000 442000 444000 446000 448000 450000 452000 454000 456000 458000 460000 462000 464000 466000 468000 470000 472000 474000 476000 478000 480000 482000 484000 486000 488000 490000 492000 494000 496000 498000 500000 502000 504000 506000 508000 510000 512000 514000 516000 518000 520000 522000 524000 526000 528000 530000 532000 534000 536000 538000 540000 54200
Appendix A Cisco Unified MeetingPlace Audio Server Software Upgrade Reference Viewing the Onsite Upgrade for a Sample Session Without a Disk Backup 568000 570000 572000 574000 576000 578000 580000 582000 584000 586000 588000 590000 592000 594000 596000 598000 600000 602000 604000 606000 608000 610000 612000 614000 616000 618000 620000 622000 624000 626000 628000 630000 632000 634000 636000 638000 640000 642000 644000 646000 648000 650000 652000 654000 656000 658000 660000 662000 664000 666000 668000 67000
Appendix A Viewing the Onsite Upgrade for a Sample Session Without a Disk Backup Cisco Unified MeetingPlace Audio Server Software Upgrade Reference 696000 698000 700000 702000 704000 706000 708000 710000 712000 714000 716000 718000 720000 722000 724000 726000 728000 730000 732000 734000 736000 738000 740000 742000 744000 746000 748000 750000 752000 754000 756000 758000 760000 762000 764000 766000 768000 770000 772000 774000 776000 778000 780000 782000 784000 786000 788000 790000 792000 794000 796000 79800
Appendix A Cisco Unified MeetingPlace Audio Server Software Upgrade Reference Viewing the Onsite Upgrade for a Sample Session Without a Disk Backup 824000 826000 828000 830000 832000 834000 836000 838000 840000 842000 844000 846000 848000 850000 852000 854000 856000 858000 860000 862000 864000 866000 868000 870000 872000 874000 876000 878000 880000 882000 884000 886000 888000 890000 892000 894000 896000 898000 900000 902000 904000 906000 908000 910000 912000 914000 916000 918000 920000 922000 924000 92600
Appendix A Viewing the Onsite Upgrade for a Sample Session Without a Disk Backup Cisco Unified MeetingPlace Audio Server Software Upgrade Reference 952000 954000 956000 958000 960000 962000 964000 966000 968000 970000 972000 974000 976000 978000 980000 982000 984000 986000 988000 990000 992000 994000 996000 998000 1000000 1000001 records found cmdbrev: delrecinit done cmdbrev: ending Mon Aug 21 19:02:50 PDT 2006 Mon Aug 21 19:02:50 PDT 2006 Network setup: Unit class = SINGLE/LOCAL Updating error log form
Appendix A Cisco Unified MeetingPlace Audio Server Software Upgrade Reference Viewing the Onsite Upgrade for a Sample Session Without a Disk Backup Running vfptrfix... Initializing the file system... Getting the disk configuration status... Checking file system internal consistency... (may take a while) ... Number of records in the prompt files has been updated, ret = a0084 Mon Aug 21 19:02:57 PDT 2006 NOTE: Disk backups disabled; run 'save' to re-enable.
Appendix A Viewing the Onsite Upgrade for a Sample Session Without a Disk Backup Cisco Unified MeetingPlace Audio Server Software Upgrade Reference Installation and Upgrade Guide for Cisco Unified MeetingPlace Audio Server 6.
INDEX modem, connecting A activity command 2-36 power, connecting to Cisco Unified MeetingPlace 8100 series 2-11 5-4 alarms, power supply unit fan SCSI, connecting to Cisco Unified MeetingPlace 8112 2-11 6-1 Australia E1 digital trunk requirements LAN cable requirements T1 CAS, connecting for Cisco Unified MeetingPlace 8112 2-13 1-10 1-13 T1 digital trunk requirements T1 CAS telephony, shipped 1-7 2-2 T1 digital trunk requirements T1 PRI telephony, shipped 1-6 2-2 B telephony, connecting
Index commands activity T1 CAS telephony cables for Cisco Unified MeetingPlace 8112 2-13 5-4 configdiskcap down telephony cables for T1 CAS/IP system 4-2 hwconfig net telephony cables for E1/IP or T1 PRI/IP system 6-3 contents of shipped boxes 6-2 ping 4-2 restart enable 4-3 update 4-2 update trace DB9 serial cable, requirement 1-4 dial-up networking, setting up 3-4 disk capacity, monitoring 4-3 down command 4-3 COM port, laptop parameters 6-3 4-2 3-2 conferencing E testing
Index Cisco Unified MeetingPlace 8106 1-4 Cisco Unified MeetingPlace 8112 1-5 J Japan European Union E1 digital trunk requirements modem requirements power requirements LAN cable requirements 1-10 modem requirements 1-12 power requirements 1-6 1-13 1-12 1-6 T1 digital trunk requirements 1-7 F L FCC registration 1-7 filter, replacing in power supply unit fan LAN 6-1 cable requirements port requirements H 1-13 1-12 laptop hardware requirements configuring 1-3 connecting to Cisco U
Index Multi Access Blades configurations for E1 and T1 PRI systems, about 2-15 connecting E1 or T1 PRI telephony cables with one MP-MA-16-PRI 2-19 with two MP-MA-16-PRIs with two MP-MA-4-PRIs Cisco Unified MeetingPlace 8112 in 19- or 23-inch frame-relay 2-4 types supported with one MP-MA-16-PRI and one MP-MA-4-PRI 2-25 with one MP-MA-4-PRI Cisco Unified MeetingPlace 8112 in 19- or 23-inch EIA equipment 2-6 2-3 recordings testing conferencing in meetings 2-23 2-26 2-24 5-6 testing conferencing i
Index mounting breakout box S 2-7 testing safety warnings 1-2 scheduling, testing inbound calls by using circular hunting 5-5 inbound calls by using dialing sequence setting up outbound calls dial-up networking HyperTerminal 3-4 TCP port requirements Singapore, wiring requirements for customer-supplied RJ-45 connectors 1-9 software, upgrading Audio Server spanstat command 1-12 for E1 and T1PRI systems, about 4-1 for IP systems, about troubleshooting 2-15 2-27 for mixed systems, about 5-
Index modem requirements power requirements 1-11 1-6 T1 digital trunk requirements 1-7 wiring requirements for customer-supplied RJ-48 connectors 1-9 UDP port requirements update command 1-12 4-2 update status command update trace command 4-3 4-3 upgrade onsite, viewing for sample session without disk backup (reference) A-16 remote, viewing for a sample session without disk backup (reference) A-1 session, viewing real-time status for remote (reference) A-3 status, viewing for a remote upgrade sess
