Regulatory Compliance and Safety Information for Cisco SB 100 Series Routers This document provides international regulatory and safety compliance information for all Cisco SB 100 series routers. Use this document with the other publications for the Cisco SB 100 series router you have purchased.
Translated Safety Warnings Translated Safety Warnings This section includes translations in multiple languages of the warnings that may appear in your product documents. The following statements are warnings or safety guidelines. A warning means danger. You are in a situation that could cause bodily injury. Before working on equipment, be aware of the hazards involved with electrical circuitry and standard safety practices to prevent accidents.
Translated Safety Warnings Attention La connexion du réseau numérique intégré (Integrated Services Digital Network ou ISDN) constitue une source de tension qui ne doit pas être accessible à l'utilisateur. Les utilisateurs ne doivent jamais tenter de modifier ni même d'ouvrir un matériel fourni par une compagnie de téléphone public, ou le matériel de connexion.
Translated Safety Warnings Statement 39—Grounded Equipment Warning Warning Waarschuwing This equipment is intended to be grounded. Ensure that the host is connected to earth ground during normal use. Deze apparatuur hoort geaard te worden Zorg dat de host-computer tijdens normaal gebruik met aarde is verbonden. Varoitus Tämä laitteisto on tarkoitettu maadoitettavaksi. Varmista, että isäntälaite on yhdistetty maahan normaalikäytön aikana. Attention Cet équipement doit être relié à la terre.
Translated Safety Warnings Statement 43—Jewelry Removal Warning Warning Before working on equipment that is connected to power lines, remove jewelry (including rings, necklaces, and watches). Metal objects will heat up when connected to power and ground and can cause serious burns or weld the metal object to the terminals. Waarschuwing Alvorens aan apparatuur te werken die met elektrische leidingen is verbonden, sieraden (inclusief ringen, kettingen en horloges) verwijderen.
Translated Safety Warnings Aviso Antes de trabalhar em equipamento que esteja ligado a linhas de corrente, retire todas as jóias que estiver a usar (incluindo anéis, fios e relógios). Os objectos metálicos aquecerão em contacto com a corrente e em contacto com a ligação à terra, podendo causar queimaduras graves ou ficarem soldados aos terminais. ¡Advertencia! Antes de operar sobre equipos conectados a líneas de alimentación, quitarse las joyas (incluidos anillos, collares y relojes).
Translated Safety Warnings Attention Lors de cette procédure, toujours porter des bracelets antistatiques pour éviter que des décharges électriques n’endommagent la carte. Pour éviter l’électrocution, ne pas toucher le fond de panier directement avec la main ni avec un outil métallique. Warnung Zur Vermeidung einer Beschädigung der Karte durch elektrostatische Entladung während dieses Verfahrens ein Erdungsband am Handgelenk tragen.
Translated Safety Warnings Statement 150—Power Off Before Working on System Warning Waarschuwing Varoitus Before working on a system that has a standby/off switch, turn off the power by pressing the power switch to standby and unplug the power cord. Alvorens aan een systeem met een standby/uit-schakelaar te werken dient u de voeding uit te schakelen door de voedingsschakelaar op standby te zetten en het voedingssnoer te verwijderen.
Translated Safety Warnings Statement 151—ISDN Network Voltages Warning Warning Network hazardous voltages are present in the ISDN cable. If you detach the ISDN cable, detach the end away from the router first to avoid possible electric shock. Network hazardous voltages also are present on the system card in the area of the ISDN port (RJ-45 connector), regardless of when power is turned off (by pressing power switch to standby).
Translated Safety Warnings ¡Advertencia! Las líneas RSDI contienen voltajes peligrosos de la red. Si desconecta el cable RSDI, separe primero el final del router para evitar posibles choques eléctricos. La tarjeta del sistema en el área del puerto RSDI (conector RJ-45) también contiene altos voltajes de la red, independientemente de si está apagada (posicionando el interruptor de la corriente a standby). Varning! I ISDN-kabeln förekommer spänningar som är farliga för nätverk.
Translated Safety Warnings Statement 1004—Installation Instructions Warning Waarschuwing Varoitus Read the installation instructions before connecting the system to the power source. Raadpleeg de installatie-instructies voordat u het systeem op de voedingsbron aansluit. Lue asennusohjeet ennen järjestelmän yhdistämistä virtalähteeseen. Attention Avant de brancher le système sur la source d'alimentation, consulter les directives d'installation.
Translated Safety Warnings Statement 1005—Circuit Breaker Warning Waarschuwing Varoitus This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 120 VAC, 15A U.S. (240 VAC, 10A international) Dit produkt is afhankelijk van de installatie van het gebouw voor kortsluit- (overstroom) beveiliging. Controleer of er een zekering of stroomverbreker van niet meer dan 120 Volt wisselstroom, 15 A voor de V.S.
Translated Safety Warnings Statement 1021—SELV Circuit Warning Waarschuwing Varoitus To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-network voltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits. Some LAN and WAN ports both use RJ-45 connectors. Use caution when connecting cables.
Translated Safety Warnings Attention Pour éviter une électrocution, ne raccordez pas les circuits de sécurité basse tension (Safety Extra-Low Voltage ou SELV) à des circuits de tension de réseau téléphonique (Telephone Network Voltage ou TNV). Les ports du réseau local (LAN) contiennent des circuits SELV et les ports du réseau longue distance (WAN) sont munis de circuits TNV. Certains ports LAN et WAN utilisent des connecteurs RJ-45. Raccordez les câbles en prenant toutes les précautions nécessaires.
Translated Safety Warnings Statement 1023—No. 26 AWG Warning Waarschuwing Varoitus To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord. Statement 1023 Om brandgevaar te reduceren, dient slechts telecommunicatielijnsnoer nr. 26 AWG of groter gebruikt te worden. Tulipalovaaran vähentämiseksi käytä ainoastaan nro 26 AWG- tai paksumpaa tietoliikennejohdinta.
Translated Safety Warnings Statement 1030—Equipment Installation Warning Waarschuwing Varoitus Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement 1030 Deze apparatuur mag alleen worden geïnstalleerd, vervangen of hersteld door bevoegd geschoold personeel. Tämän laitteen saa asentaa, vaihtaa tai huoltaa ainoastaan koulutettu ja laitteen tunteva henkilökunta.
Translated Safety Warnings Aviso Advarsel Warning Waarschuwing Varoitus Somente uma equipe treinada e qualificada tem permissão para instalar, substituir ou dar manutenção a este equipamento. Kun uddannede personer må installere, udskifte komponenter i eller servicere dette udstyr. Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Deze apparatuur mag alleen worden geïnstalleerd, vervangen of hersteld door bevoegd geschoold personeel.
Translated Safety Warnings Attention Il est vivement recommandé de confier l'installation, le remplacement et la maintenance de ces équipements à des personnels qualifiés et expérimentés. Warnung Das Installieren, Ersetzen oder Bedienen dieser Ausrüstung sollte nur geschultem, qualifiziertem Personal gestattet werden. Avvertenza Questo apparato può essere installato, sostituito o mantenuto unicamente da un personale competente.
Translated Safety Warnings Aviso Advarsel O descarte definitivo deste produto deve estar de acordo com todas as leis e regulamentações nacionais. Endelig bortskaffelse af dette produkt skal ske i henhold til gældende love og regler.
Agency Approvals Agency Approvals Table 1 lists the safety and electromagnetic interference (EMI) standards that apply to the Cisco SB 100 series routers.
FCC Class B Statement • TIA/EIA/IS-968, Technical Criteria for Terminal Equipment to Prevent Harm to the Telephone Network, July 2001, as adopted by the Administrative Council on Terminal Attachments (ACTA). The Cisco SB 100 series routers comply with Part 68 of the FCC rules. An FCC-compliant telephone cord and modular plug is provided with this equipment, designed to be connected to the telephone network or premises wiring using a compatible modular jack that is Part 68 compliant.
CISPR 22 Class B Statement CISPR 22 Class B Statement Emissions: This equipment complies with the requirements of CISPR 22 (EN 55022) for Class B Information Technology Equipment (ITE). Operating Conditions for Canada In addition to the warnings and safety guidelines listed in the “Obtaining Documentation” section on page 25, the following operating condition applies to routers used in Canada: The Industry Canada label identifies certified equipment.
Declaration of Conformity “These ports do not provide isolation sufficient to satisfy the requirement of EN 41003; apparatus connected to these ports should either have been approved to EN 41003 or have previously been evaluated against B5E301 British Telecommunications plc (Post Office) Technical Guides 2 or 26 and given permission to attach; any that other usage will invalidate any approval given to this apparatus.
Compliance Statements for Canada Compliance Statements for Canada Canadian Class B Statement This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of the Department of Communications.
Obtaining Documentation Obtaining Documentation Cisco documentation and additional literature are available on Cisco.com. Cisco also provides several ways to obtain technical assistance and other technical resources. These sections explain how to obtain technical information from Cisco Systems. Cisco.com You can access the most current Cisco documentation at this URL: http://www.cisco.com/univercd/home/home.htm You can access the Cisco website at this URL: http://www.cisco.
Obtaining Technical Assistance Obtaining Technical Assistance For all customers, partners, resellers, and distributors who hold valid Cisco service contracts, Cisco Technical Support provides 24-hour-a-day, award-winning technical assistance. The Cisco Technical Support Website on Cisco.com features extensive online support resources. In addition, Cisco Technical Assistance Center (TAC) engineers provide telephone support. If you do not hold a valid Cisco service contract, contact your reseller.
Obtaining Additional Publications and Information Definitions of Service Request Severity To ensure that all service requests are reported in a standard format, Cisco has established severity definitions. Severity 1 (S1)—Your network is “down,” or there is a critical impact to your business operations. You and Cisco will commit all necessary resources around the clock to resolve the situation.
Obtaining Additional Publications and Information • Internet Protocol Journal is a quarterly journal published by Cisco Systems for engineering professionals involved in designing, developing, and operating public and private internets and intranets. You can access the Internet Protocol Journal at this URL: http://www.cisco.com/ipj • World-class networking training is available from Cisco. You can view current offerings at this URL: http://www.cisco.com/en/US/learning/index.
