Ege 10/100 Dual Speed Ethernet Hub teeters FCC Compliance Statement This device compliance with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
18/100 Dual Speed Ethernet Hub CE Compliance Statement We hereby certify that the Ethernet Hub complies with the EN 50081-1 and EN 50082-1 requirements. ce NOTE: EN 50082-1 standard: IEC 861.
10/100 Dual Speed Ethernet Hub Chapter 1 Introduction The Ethernet Hub is a dual-speed hub that is designed to easily integrate the Fast Ethernet network into your existing 10 Bps network work groups. The dual-speed hub consists of two internal network segments, ong is for {BASE-Tnetwork operation, the other ane is providing [00BASE-TX Ethernet connection. | also includes an internal switching port to interlink different data transferring between 10 and 100 Bps networks.
10/100 Dual Speed Ethernet Hub Package Contents ‘The package of your dual-speed Ethernet hub should contain the following items: 0 Dual-speed Theme hub 0 External power adapter 0 User manual NOTE: If any items is missing or damaged, please contact your dealer for replacement.
10/1060 Dual Speed Ethernet Hub LED Indicators The dual-speed Ethernet hub provides» variety of informative LED on the front panel for easy viewing and troubleshooting. PWR LED The green LED indicates the power status, This green LED will be lit while the hub is receiving power. LED The amber LED displays the 10 Bps network collision status, If a collision is detected on the internal 10Mbps network segment, the amber LED will flash.
10/100 Dual Speed Ethernet Hub Utilization LED The green LED displays the network utilization status. The corresponding LED (shown as 1% ~ 50%) will light when the network traffic utilization has reached the percentage NOTE: Figure 1-1 saws the front view of the Dual-specs hubs LED indication, The switch can be easily configuration of last JR-45 port as a MDI or MID-X pin assignment.
10/100 Dual Speed Ethernet Hub Chapter 2 Installing the Dual-speed Hub Pr-Tnstallation Requirements Before you connect the dual-speed Ethernet hub to the network, make sure Thai you have had the proper operating environment, To provide the proper operating condition, make sure the following installation requirements: i Power Requirement: 100 to 240VAC Cable Requirement: The dual-speed Ethernet hub requires Category UTP cable wiring for the 10 Bps connection.
/100 Dual Speed Ethernet Hub Connection for a 10 and 100 Bps Device The dual-speed hub is equipped with five (5) R145 ports. Be sure to use the proper cable wiring to connect the hub 100 Bps network device. Verify the following connection requirements. NOTE: I. Set the switch to position "MID-X" while connect this dual-speed bub 100 Bps server or workstation, 2. Set the switch to position “MDI” while connect this dual-speed hub 100 Bps Ethernet hub.
10/100 Dual Speed Ethernet Hub Connection for Hubs Cascading The last JR-45 port of your dual-speed hub could be configured as MDI pin assignment and enable you to daisy-chain to another 10 or 100 Bps Ethernet hub. Before cascading the dual-speed hub to another, please make size the following installation requirements: 10 Bps Hub Cascading Use Category 3,4 or 5 UTP cable to link your dual-speed hub to another 10 Bps Ethernet hub. Make sure the UTP cable dares not exceed 100m. Based on IEEE 802.
10/100 Dual Speed Ethernet Hub Appendix A Specifications IEEE 802.3 standards: Wiring Connectors: Weight: Dimensions: Emission Certifications: Immunity Certifications: Input Voltage: Power Consumption; Operating Temperature: Operating Humidity: Operating Altitude: ABASE-T, 100BASE-TX RJ-45%5 480g 6.3" x 3.9" x 0.98" (160mm x 100mm x 25mm} FCC Part 15 Class B IEC 801-2 {Electrostatic Discharge) 1EC 801-3 (Radiated Immunity) IEC 801-4 (Electrical Fast Transient/Burst) 1.
10/100 Dual Speed Ethernet Hub — Appendix B JR-45 pin assignments 0 Twit iP Tear Rams ramie 0 Aon Table A-1: RISKS connector pin assignments JR-45 pin connector ET 0 Phone Side Plug Side Table A-2: RJ-4S connector pin locations
