Owner's manual

ManualsBrandsCirrus Logic ManualsHardwareEP93xx

451

452

453

454

455

456

457

458

459

460

Table Of Contents

Contents
- Figures
- Tables
- Revision History
Preface
- P.1 About the EP93xx User’s Guide
- P.2 Related Documents from Cirrus Logic
- P.3 Reference Documents
- P.4 Notational Conventions
- P.5 Register Example
Introduction
- 1.1 Introduction
- 1.2 EP93xx Features
- 1.3 EP93xx Processor Applications
- 1.4 EP93xx Processor Highlights
ARM920T Core and Advanced High-Speed Bus (AHB)
- 2.1 Introduction
- 2.2 Overview: ARM920T Core
- 2.3 AHB Decoder
MaverickCrunch Co-Processor
- 3.1 Introduction
- 3.2 Programming Examples
  - 3.2.1 Example 1
  - 3.2.2 Example 2
    - 3.2.2.1 C Code
    - 3.2.2.2 MaverickCrunch Assembly Language Instructions
- 3.3 DSPSC Register
- 3.4 ARM Co-Processor Instruction Format
- 3.5 Instruction Set for the MaverickCrunch Co-Processor
Boot ROM
- 4.1 Introduction
  - 4.1.1 Boot ROM Hardware Operational Overview
    - 4.1.1.1 Memory Map
  - 4.1.2 Boot ROM Software Operational Overview
- 4.2 Boot Options
System Controller
- 5.1 Introduction
- 5.2 Registers
Vectored Interrupt Controller
- 6.1 Introduction
- 6.2 Registers
Raster Engine With Analog/LCD Integrated Timing and Interface
- 7.1 Introduction
- 7.2 Features
- 7.3 Raster Engine Features Overview
- 7.4 Functional Details
- 7.5 Registers
Graphics Accelerator
- 8.1 Overview
- 8.2 Block Processing Modes
- 8.3 Line Draws
  - 8.3.1 Breshenham Line Draws
  - 8.3.2 Pixel Step Line Draws
- 8.4 Memory Organization for Graphics Accelerator
- 8.5 Register Programming
  - 8.5.1 Word Count
    - 8.5.1.1 Example: 8 BPP mode
    - 8.5.1.2 Example: 24 BPP (packed) mode
  - 8.5.2 Pixel End and Start
- 8.6 Register Usage
- 8.7 Registers
1/10/100 Mbps Ethernet LAN Controller
- 9.1 Introduction
- 9.2 Descriptor Processor
- 9.3 Registers
DMA Controller
- 10.1 Introduction
- 10.2 Registers
  - 10.2.1 DMA Controller Memory Map
  - 10.2.2 Internal M2P/P2M Channel Register Map
Universal Serial Bus Host Controller
- 11.1 Introduction
  - 11.1.1 Features
- 11.2 Overview
- 11.3 Registers
Static Memory Controller
- 12.1 Introduction
- 12.2 Static Memory Controller Operation
- 12.3 PCMCIA Interface (EP9315 Processor Only)
- 12.4 PC Card Memory-Mode Enable Signals
- 12.5 PC Card Memory Mapping
- 12.6 Registers
  - 12.6.1 Bank Configuration Registers
  - 12.6.2 PCMCIA Configuration Registers (EP9315 Processor Only)
SDRAM, SyncROM, and SyncFLASH Controller
- 13.1 Introduction
- 13.2 Booting from SyncROM or SyncFLASH
- 13.3 Address Pin Usage
- 13.4 SDRAM Initialization
- 13.5 Programming Mode Register: SDRAM Or SyncROM Device
- 13.6 SDRAM Self Refresh
  - 13.6.1 Entering Self Refresh Mode
  - 13.6.2 Exiting Self Refresh Mode
- 13.7 Programming Registers: SyncFLASH Device
- 13.8 External Synchronous Memory System
  - 13.8.1 Chip Select SDCSN[3:0] Decoding
  - 13.8.2 Address/Data/Control Required by Memory System
- 13.9 Registers
UART1 With HDLC and Modem Control Signals
- 14.1 Introduction
- 14.2 UART Overview
- 14.3 Modem
- 14.4 HDLC
- 14.5 UART1 Package Dependency
  - 14.5.1 Clocking Requirements
  - 14.5.2 Bus Bandwidth Requirements
- 14.1 Registers
UART2
- 15.1 Introduction
- 15.2 IrDA SIR Block
- 15.3 UART2 Package Dependency
  - 15.3.1 Clocking Requirements
  - 15.3.2 Bus Bandwidth Requirements
- 15.4 Registers
UART3 With HDLC Encoder
- 16.1 Introduction
- 16.2 Implementation Details
- 16.3 Registers
IrDA
- 17.1 Introduction
- 17.2 IrDA Interfaces
- 17.3 Shared IrDA Interface Feature
- 17.4 Medium IrDA Specific Features
  - 17.4.1 Introduction
    - 17.4.1.1 Bit Encoding
    - 17.4.1.2 Frame Format
  - 17.4.2 Functional Description
- 17.5 Fast IrDA Specific Features
- 17.6 Registers
Timers
- 18.1 Introduction
- 18.2 Registers
Watchdog Timer
- 19.1 Introduction
- 19.1 Registers
Real Time Clock With Software Trim
- 20.1 Introduction
  - 20.1.1 Software Trim
  - 20.1.2 Reset Control
- 20.1 Registers
I2S Controller
- 21.1 Introduction
- 21.2 I2S Transmitter Channel Overview
- 21.3 I2S Receiver Channel Overview
  - 21.3.1 Receiver FIFO’s
- 21.4 I2S Master Clock Generation
- 21.5 I2S Bit Clock Rate Generation
  - 21.5.1 Example of the Bit Clock Generation.
  - 21.5.2 Example of Right Justified LRCK format
- 21.6 Interrupts
- 21.7 Registers
AC’97 Controller
- 22.1 Introduction
- 22.2 Interrupts
  - 22.2.1 Channel Interrupts
  - 22.2.2 Global Interrupts
- 22.3 System Loopback Testing
- 22.4 Registers
Synchronous Serial Port
- 23.1 Introduction
- 23.2 Features
- 23.3 SSP Functionality
- 23.4 SSP Pin Multiplex
- 23.5 Configuring the SSP
- 23.6 Registers
Pulse Width Modulator
- 24.1 Introduction
- 24.2 Theory of Operation
  - 24.2.1 PWM Programming Examples
  - 24.2.2 Programming Rules
- 24.3 Registers
Analog Touch Screen Interface
- 25.1 Introduction
- 25.2 Touch Screen Controller Operation
- 25.3 Registers
Keypad Interface
- 26.1 Introduction
- 26.2 Theory of Operation
- 26.3 Registers
IDE Interface
- 27.1 Introduction
- 27.2 Theory of Operation
- 27.3 Registers
GPIO Interface
- 28.1 Introduction
- 28.2 Registers
Security
- 29.1 Introduction
- 29.2 Features
- 29.3 Contact Information
- 29.4 Registers
Glossary
EP93XX Register List

11-16 DS785UM1

Universal Serial Bus Host Controller

EP93xx User’s Guide

CLF: ControlListFilled:

This bit is used to indicate whether there are any TDs on

the Control list. It is set by HCD whenever it adds a TD to

an ED in the Control list. When HC begins to process the

head of the Control list, it checks CLF. As long as

ControlListFilled is 0, HC will not start processing the

Control list. If CF is 1, HC will start processing the Control

list and will set ControlListFilled to 0. If HC finds a TD on

the list, then HC will set ControlListFilled to 1 causing the

Control list processing to continue. If no TD is found on the

Control list, and if the HCD does not set ControlListFilled,

then ControlListFilled will still be 0 when HC completes

processing the Control list and Control list processing will

stop.

BLF: BulkListFilled:

This bit is used to indicate whether there are any TDs on

the Bulk list. It is set by HCD whenever it adds a TD to an

ED in the Bulk list. When HC begins to process the head

of the Bulk list, it checks BF. As long as BulkListFilled is 0,

HC will not start processing the Bulk list. If BulkListFilled is

1, HC will start processing the Bulk list and will set BF to 0.

If HC finds a TD on the list, then HC will set BulkListFilled

to 1 causing the Bulk list processing to continue. If no TD

is found on the Bulk list, and if HCD does not set

BulkListFilled, then BulkListFilled will still be 0 when HC

completes processing the Bulk list and Bulk list processing

will stop.

OCR: OwnershipChangeRequest:

This bit is set by an OS HCD to request a change of

control of the HC. When set HC will set the

OwnershipChange field in HcInterruptStatus. After the

changeover, this bit is cleared and remains so until the

next request from OS HCD.

SOC: SchedulingOverrunCount:

These bits are incremented on each scheduling overrun

error. It is initialized to 00b and wraps around at 11b. This

will be incremented when a scheduling overrun is detected

even if SchedulingOverrun in HcInterruptStatus has

already been set. This is used by HCD to monitor any

persistent scheduling problems.