Owner's manual

ManualsBrandsCirrus Logic ManualsHardwareEP93xx

371

372

373

374

375

376

377

378

379

380

Table Of Contents

Contents
- Figures
- Tables
- Revision History
Preface
- P.1 About the EP93xx User’s Guide
- P.2 Related Documents from Cirrus Logic
- P.3 Reference Documents
- P.4 Notational Conventions
- P.5 Register Example
Introduction
- 1.1 Introduction
- 1.2 EP93xx Features
- 1.3 EP93xx Processor Applications
- 1.4 EP93xx Processor Highlights
ARM920T Core and Advanced High-Speed Bus (AHB)
- 2.1 Introduction
- 2.2 Overview: ARM920T Core
- 2.3 AHB Decoder
MaverickCrunch Co-Processor
- 3.1 Introduction
- 3.2 Programming Examples
  - 3.2.1 Example 1
  - 3.2.2 Example 2
    - 3.2.2.1 C Code
    - 3.2.2.2 MaverickCrunch Assembly Language Instructions
- 3.3 DSPSC Register
- 3.4 ARM Co-Processor Instruction Format
- 3.5 Instruction Set for the MaverickCrunch Co-Processor
Boot ROM
- 4.1 Introduction
  - 4.1.1 Boot ROM Hardware Operational Overview
    - 4.1.1.1 Memory Map
  - 4.1.2 Boot ROM Software Operational Overview
- 4.2 Boot Options
System Controller
- 5.1 Introduction
- 5.2 Registers
Vectored Interrupt Controller
- 6.1 Introduction
- 6.2 Registers
Raster Engine With Analog/LCD Integrated Timing and Interface
- 7.1 Introduction
- 7.2 Features
- 7.3 Raster Engine Features Overview
- 7.4 Functional Details
- 7.5 Registers
Graphics Accelerator
- 8.1 Overview
- 8.2 Block Processing Modes
- 8.3 Line Draws
  - 8.3.1 Breshenham Line Draws
  - 8.3.2 Pixel Step Line Draws
- 8.4 Memory Organization for Graphics Accelerator
- 8.5 Register Programming
  - 8.5.1 Word Count
    - 8.5.1.1 Example: 8 BPP mode
    - 8.5.1.2 Example: 24 BPP (packed) mode
  - 8.5.2 Pixel End and Start
- 8.6 Register Usage
- 8.7 Registers
1/10/100 Mbps Ethernet LAN Controller
- 9.1 Introduction
- 9.2 Descriptor Processor
- 9.3 Registers
DMA Controller
- 10.1 Introduction
- 10.2 Registers
  - 10.2.1 DMA Controller Memory Map
  - 10.2.2 Internal M2P/P2M Channel Register Map
Universal Serial Bus Host Controller
- 11.1 Introduction
  - 11.1.1 Features
- 11.2 Overview
- 11.3 Registers
Static Memory Controller
- 12.1 Introduction
- 12.2 Static Memory Controller Operation
- 12.3 PCMCIA Interface (EP9315 Processor Only)
- 12.4 PC Card Memory-Mode Enable Signals
- 12.5 PC Card Memory Mapping
- 12.6 Registers
  - 12.6.1 Bank Configuration Registers
  - 12.6.2 PCMCIA Configuration Registers (EP9315 Processor Only)
SDRAM, SyncROM, and SyncFLASH Controller
- 13.1 Introduction
- 13.2 Booting from SyncROM or SyncFLASH
- 13.3 Address Pin Usage
- 13.4 SDRAM Initialization
- 13.5 Programming Mode Register: SDRAM Or SyncROM Device
- 13.6 SDRAM Self Refresh
  - 13.6.1 Entering Self Refresh Mode
  - 13.6.2 Exiting Self Refresh Mode
- 13.7 Programming Registers: SyncFLASH Device
- 13.8 External Synchronous Memory System
  - 13.8.1 Chip Select SDCSN[3:0] Decoding
  - 13.8.2 Address/Data/Control Required by Memory System
- 13.9 Registers
UART1 With HDLC and Modem Control Signals
- 14.1 Introduction
- 14.2 UART Overview
- 14.3 Modem
- 14.4 HDLC
- 14.5 UART1 Package Dependency
  - 14.5.1 Clocking Requirements
  - 14.5.2 Bus Bandwidth Requirements
- 14.1 Registers
UART2
- 15.1 Introduction
- 15.2 IrDA SIR Block
- 15.3 UART2 Package Dependency
  - 15.3.1 Clocking Requirements
  - 15.3.2 Bus Bandwidth Requirements
- 15.4 Registers
UART3 With HDLC Encoder
- 16.1 Introduction
- 16.2 Implementation Details
- 16.3 Registers
IrDA
- 17.1 Introduction
- 17.2 IrDA Interfaces
- 17.3 Shared IrDA Interface Feature
- 17.4 Medium IrDA Specific Features
  - 17.4.1 Introduction
    - 17.4.1.1 Bit Encoding
    - 17.4.1.2 Frame Format
  - 17.4.2 Functional Description
- 17.5 Fast IrDA Specific Features
- 17.6 Registers
Timers
- 18.1 Introduction
- 18.2 Registers
Watchdog Timer
- 19.1 Introduction
- 19.1 Registers
Real Time Clock With Software Trim
- 20.1 Introduction
  - 20.1.1 Software Trim
  - 20.1.2 Reset Control
- 20.1 Registers
I2S Controller
- 21.1 Introduction
- 21.2 I2S Transmitter Channel Overview
- 21.3 I2S Receiver Channel Overview
  - 21.3.1 Receiver FIFO’s
- 21.4 I2S Master Clock Generation
- 21.5 I2S Bit Clock Rate Generation
  - 21.5.1 Example of the Bit Clock Generation.
  - 21.5.2 Example of Right Justified LRCK format
- 21.6 Interrupts
- 21.7 Registers
AC’97 Controller
- 22.1 Introduction
- 22.2 Interrupts
  - 22.2.1 Channel Interrupts
  - 22.2.2 Global Interrupts
- 22.3 System Loopback Testing
- 22.4 Registers
Synchronous Serial Port
- 23.1 Introduction
- 23.2 Features
- 23.3 SSP Functionality
- 23.4 SSP Pin Multiplex
- 23.5 Configuring the SSP
- 23.6 Registers
Pulse Width Modulator
- 24.1 Introduction
- 24.2 Theory of Operation
  - 24.2.1 PWM Programming Examples
  - 24.2.2 Programming Rules
- 24.3 Registers
Analog Touch Screen Interface
- 25.1 Introduction
- 25.2 Touch Screen Controller Operation
- 25.3 Registers
Keypad Interface
- 26.1 Introduction
- 26.2 Theory of Operation
- 26.3 Registers
IDE Interface
- 27.1 Introduction
- 27.2 Theory of Operation
- 27.3 Registers
GPIO Interface
- 28.1 Introduction
- 28.2 Registers
Security
- 29.1 Introduction
- 29.2 Features
- 29.3 Contact Information
- 29.4 Registers
Glossary
EP93XX Register List

DS785UM1 9-69

1/10/100 Mbps Ethernet LAN Controller

EP93xx User’s Guide

TxEn: Transmit Enable. Writing a one to Transmit Enable causes

transmit DMA transfers to be enabled. This is reflected in

TxAct (Bus Master Status) being set. TxEn is an act-once-

bit and will clear automatically when the enable is

complete. The first time the TxEn bit is set following an

AHB reset, or a TxChRes, the MAC performs a transmit

channel initialization. During this initialization the TXDEnq

is cleared, and the Transmit Descriptor and Status Queues

are calculated. When the initialization is complete, the

TxAct (BMSts) is set.

EH2: Enable Header 2. When Enable Header2 is set, a status is

written to the receive status queue when the number of

bytes specified in Receive Header Length2 have been

transferred to the receive data buffer. If the transfer either

fills a receive buffer or ends a receive frame, only an end

of buffer or end of frame status is generated. The value in

Receive Header Length 2 should be greater than the value

in Receive Header Length 1 in order to generate a status

event.

EH1: Enable Header 1. When Enable Header1 is set, a status is

written to the receive status queue when the number of

bytes specified in Receive Header Length1 have been

transferred to the receive data buffer. If the transfer either

fills a receive buffer or ends a receive frame, only an end

of buffer or end of frame status is generated.

EEOB: Enable EOB. When Enable End Of Buffer bit is set, a

status is written to the receive status queue whenever an

end of receive buffer is reached. If reaching the end of the

receive buffer coincides with the end of frame, only one

status is written to the queue.

RxChR: Receive Channel Reset. Writing a “1” to Receive Channel

Reset causes the Receive Descriptor Processor and the

receive FIFO to be reset. This bit is an act-once-bit and

will clear automatically when the reset is complete.

RxDis: Receive Disable. Writing a “1” to Receive Disable causes

receive DMA transfers to be halted. If a receive frame is

currently in progress, transfers will be halted when the

receive frame status has been transferred to the status

buffer. When the transfers are halted, the RxAct bit (Bus

Master Status) is cleared. This bit is an act-once-bit and

will clear immediately.