Owner's manual

ManualsBrandsCirrus Logic ManualsHardwareEP93xx

321

322

323

324

325

326

327

328

329

330

Table Of Contents

Contents
- Figures
- Tables
- Revision History
Preface
- P.1 About the EP93xx User’s Guide
- P.2 Related Documents from Cirrus Logic
- P.3 Reference Documents
- P.4 Notational Conventions
- P.5 Register Example
Introduction
- 1.1 Introduction
- 1.2 EP93xx Features
- 1.3 EP93xx Processor Applications
- 1.4 EP93xx Processor Highlights
ARM920T Core and Advanced High-Speed Bus (AHB)
- 2.1 Introduction
- 2.2 Overview: ARM920T Core
- 2.3 AHB Decoder
MaverickCrunch Co-Processor
- 3.1 Introduction
- 3.2 Programming Examples
  - 3.2.1 Example 1
  - 3.2.2 Example 2
    - 3.2.2.1 C Code
    - 3.2.2.2 MaverickCrunch Assembly Language Instructions
- 3.3 DSPSC Register
- 3.4 ARM Co-Processor Instruction Format
- 3.5 Instruction Set for the MaverickCrunch Co-Processor
Boot ROM
- 4.1 Introduction
  - 4.1.1 Boot ROM Hardware Operational Overview
    - 4.1.1.1 Memory Map
  - 4.1.2 Boot ROM Software Operational Overview
- 4.2 Boot Options
System Controller
- 5.1 Introduction
- 5.2 Registers
Vectored Interrupt Controller
- 6.1 Introduction
- 6.2 Registers
Raster Engine With Analog/LCD Integrated Timing and Interface
- 7.1 Introduction
- 7.2 Features
- 7.3 Raster Engine Features Overview
- 7.4 Functional Details
- 7.5 Registers
Graphics Accelerator
- 8.1 Overview
- 8.2 Block Processing Modes
- 8.3 Line Draws
  - 8.3.1 Breshenham Line Draws
  - 8.3.2 Pixel Step Line Draws
- 8.4 Memory Organization for Graphics Accelerator
- 8.5 Register Programming
  - 8.5.1 Word Count
    - 8.5.1.1 Example: 8 BPP mode
    - 8.5.1.2 Example: 24 BPP (packed) mode
  - 8.5.2 Pixel End and Start
- 8.6 Register Usage
- 8.7 Registers
1/10/100 Mbps Ethernet LAN Controller
- 9.1 Introduction
- 9.2 Descriptor Processor
- 9.3 Registers
DMA Controller
- 10.1 Introduction
- 10.2 Registers
  - 10.2.1 DMA Controller Memory Map
  - 10.2.2 Internal M2P/P2M Channel Register Map
Universal Serial Bus Host Controller
- 11.1 Introduction
  - 11.1.1 Features
- 11.2 Overview
- 11.3 Registers
Static Memory Controller
- 12.1 Introduction
- 12.2 Static Memory Controller Operation
- 12.3 PCMCIA Interface (EP9315 Processor Only)
- 12.4 PC Card Memory-Mode Enable Signals
- 12.5 PC Card Memory Mapping
- 12.6 Registers
  - 12.6.1 Bank Configuration Registers
  - 12.6.2 PCMCIA Configuration Registers (EP9315 Processor Only)
SDRAM, SyncROM, and SyncFLASH Controller
- 13.1 Introduction
- 13.2 Booting from SyncROM or SyncFLASH
- 13.3 Address Pin Usage
- 13.4 SDRAM Initialization
- 13.5 Programming Mode Register: SDRAM Or SyncROM Device
- 13.6 SDRAM Self Refresh
  - 13.6.1 Entering Self Refresh Mode
  - 13.6.2 Exiting Self Refresh Mode
- 13.7 Programming Registers: SyncFLASH Device
- 13.8 External Synchronous Memory System
  - 13.8.1 Chip Select SDCSN[3:0] Decoding
  - 13.8.2 Address/Data/Control Required by Memory System
- 13.9 Registers
UART1 With HDLC and Modem Control Signals
- 14.1 Introduction
- 14.2 UART Overview
- 14.3 Modem
- 14.4 HDLC
- 14.5 UART1 Package Dependency
  - 14.5.1 Clocking Requirements
  - 14.5.2 Bus Bandwidth Requirements
- 14.1 Registers
UART2
- 15.1 Introduction
- 15.2 IrDA SIR Block
- 15.3 UART2 Package Dependency
  - 15.3.1 Clocking Requirements
  - 15.3.2 Bus Bandwidth Requirements
- 15.4 Registers
UART3 With HDLC Encoder
- 16.1 Introduction
- 16.2 Implementation Details
- 16.3 Registers
IrDA
- 17.1 Introduction
- 17.2 IrDA Interfaces
- 17.3 Shared IrDA Interface Feature
- 17.4 Medium IrDA Specific Features
  - 17.4.1 Introduction
    - 17.4.1.1 Bit Encoding
    - 17.4.1.2 Frame Format
  - 17.4.2 Functional Description
- 17.5 Fast IrDA Specific Features
- 17.6 Registers
Timers
- 18.1 Introduction
- 18.2 Registers
Watchdog Timer
- 19.1 Introduction
- 19.1 Registers
Real Time Clock With Software Trim
- 20.1 Introduction
  - 20.1.1 Software Trim
  - 20.1.2 Reset Control
- 20.1 Registers
I2S Controller
- 21.1 Introduction
- 21.2 I2S Transmitter Channel Overview
- 21.3 I2S Receiver Channel Overview
  - 21.3.1 Receiver FIFO’s
- 21.4 I2S Master Clock Generation
- 21.5 I2S Bit Clock Rate Generation
  - 21.5.1 Example of the Bit Clock Generation.
  - 21.5.2 Example of Right Justified LRCK format
- 21.6 Interrupts
- 21.7 Registers
AC’97 Controller
- 22.1 Introduction
- 22.2 Interrupts
  - 22.2.1 Channel Interrupts
  - 22.2.2 Global Interrupts
- 22.3 System Loopback Testing
- 22.4 Registers
Synchronous Serial Port
- 23.1 Introduction
- 23.2 Features
- 23.3 SSP Functionality
- 23.4 SSP Pin Multiplex
- 23.5 Configuring the SSP
- 23.6 Registers
Pulse Width Modulator
- 24.1 Introduction
- 24.2 Theory of Operation
  - 24.2.1 PWM Programming Examples
  - 24.2.2 Programming Rules
- 24.3 Registers
Analog Touch Screen Interface
- 25.1 Introduction
- 25.2 Touch Screen Controller Operation
- 25.3 Registers
Keypad Interface
- 26.1 Introduction
- 26.2 Theory of Operation
- 26.3 Registers
IDE Interface
- 27.1 Introduction
- 27.2 Theory of Operation
- 27.3 Registers
GPIO Interface
- 28.1 Introduction
- 28.2 Registers
Security
- 29.1 Introduction
- 29.2 Features
- 29.3 Contact Information
- 29.4 Registers
Glossary
EP93XX Register List

DS785UM1 9-19

1/10/100 Mbps Ethernet LAN Controller

EP93xx User’s Guide

EOF: End Of Frame. When this bit is set, the associated buffer

contains the last data associated with this frame. In the

case of an extra data or overrun error, the buffer may not

contain the actual end of frame data. For a receive header

status the EOF and EOB bits will both be clear.

EOB: End Of Buffer. When this bit is set, no more data will be

transferred to the associated data buffer. This may be due

to an end of frame transfer or to reaching the actual end of

the buffer. For a receive header status the EOF and EOB

bits will both be clear.

AM: Address Match:

00 - Individual Address match

01 - Global Address match

10 - Hashed Individual Address

11 - Hashed Multicast Address

RX_Err: RX Error. The RX_Err is set for any receive frame for

which the RX_ERR (MII pin) was activated.

OE: Overrun Error. The receive overrun bit is set on any frame

which could not be completely transferred to system

memory. This could be as a result of insufficient buffer

space, or an excessive bus arbitration time.

FE: Framing Error. This bit is set for any frame not having an

integral number of bytes, and received with a bad CRC

value.

Runt: Runt Frame. The Runt bit is set for any receive frame,

including CRC, that is shorter than 64 bytes.

EData: Extra Data. The ExtraData bit indicates that the length of

the incoming frame was equal or greater than the value

programmed in the Max Frame Len register. The receive

frame will be terminated at this maximum length to

conserve system buffer space.

CRCE: CRC Error. This indicates the frame was received with a

bad CRC.

CRCI: CRC Included. This bit is set to one when the CRC has

been included in the Receive data buffer. Including or

excluding the CRC is controlled by the BufferCRC bit in

the RXCtl register.